Cited by 3Ferroelectric and Piezoelectric MaterialsAdvancements in Solid Oxide Fuel CellsElectronic and Structural Properties of Oxides

Chemical and phase inhomogeneity in LaNiO3 electrodes prepared by chemical solution deposition

Atanova, A. V., Zhigalina, O. M., Khmelenin, D. N., Kotova, N. M., Seregin, D. S., Vorotilov, K. A.·2021·Ferroelectrics

Abstract

The structure of lanthanum nickelate (LNO) thin film electrodes prepared by chemical solution deposition has been investigated. Features of LNO microstructure have been studied using high-resolution transmission electron microscopy techniques, electron diffraction, and elemental mapping by energy dispersive X-ray analysis. Structure evolution of LNO after crystallization in the temperature range of 550 ÷ 800 °C has been visualized. Chemical and phase delamination within each sublayer was revealed in the LNO structure over the entire temperature range. Nanograins of Ni3O4 (С2/m), La2O3 (С2/m), LaNiO3 (Pm3¯m), and La2Ni2O5 (С2/m) phases were identified in the annealed LNO layer.

Integrity signals

Registry

Crossref · 10.1080/00150193.2021.1888046

Cites

1 of 1 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Claims the paper makes

This paper’s full text isn’t openly available, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

  • If drying proceeds in 300-450 °C range, interaction between metal oxide molecules occurs and crystallization creates not only LaNiO3 but also Ni3O4, La2O3 and La2Ni2O5 phases.

    “If drying proceeds in this temperature range, an interaction between metal oxide molecules occurs and crystallization creates not only LaNiO3 (s.g. Pm3¯m), but also Ni3O4 (C2/m), La2O3 (C2/m) and La2Ni2O5 (C2/m) phases [71].”

    From Control of Columnar Grain Microstructure in CSD LaNiO3 Films (2023) · cites this paper as [71]

  • In case of hard-baking at 300-450 °C, intermediate phases are created and final annealing at 650 °C gives multiphase structure.

    “In contrast, in the case of hard-baking at 300–450 °C, intermediate phases are created and final annealing at 650 °C gives the multiphase structure, as it was mentioned before [71].”

    From Control of Columnar Grain Microstructure in CSD LaNiO3 Films (2023) · cites this paper as [71]

Cites

Flagged first, then by citations

Cited by

Sorted by citations

Authors
Atanova, A. V., Zhigalina, O. M., Khmelenin, D. N., Kotova, N. M., Seregin, D. S., & Vorotilov, K. A.
Affiliations
  • FSRC “Crystallography and Photonics” RAS, Moscow, Russia
  • Bauman Moscow State Technical University (RU)
  • Federal Scientific Research Centre Crystallography and Photonics (RU)
  • MIREA - Russian Technological University, Moscow, Russia
  • MIREA - Russian Technological University (RU)
Venue
Ferroelectrics
Published
2021-04-04
Volume
574
Issue
1
Pages
29-36
ISSN
  • 0015-0193 (ISSN-L)
  • 1563-5112
OpenAlex
W3158564484
Cited by
3
References
1
Citations by year
2024: 1 · 2023: 1 · 2022: 1
FWCI
0.23
Type
journal article
Language
en
Open access
closed
Locations
Ferroelectrics (publishedVersion)
Funders
  • Ministry of Science and Higher Education program (0706-2020-0022)
  • RFBR (19-29-03058)
  • Crystallography and Photonics (RFMEFI62119X0035)
Topics
  • Physical Sciences › Materials Science › Materials Chemistry › Ferroelectric and Piezoelectric Materials
  • Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
  • Physical Sciences › Materials Science › Materials Chemistry › Electronic and Structural Properties of Oxides
Keywords
LaNiO3, LaNiO3 thin films, chemical solution deposition, phase inhomogeneity, compositional heterogeneity, microstructure, crystallization, lanthanum oxide, annealing, electrode structure

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review