Modeling ethylene/butene copolymerization with multi-site catalysts: parameter estimability and experimental design
The DOI matches its Crossref record; 33 of the 34 references it cites were found in a registry or an index.
Abstract
Mechanistic models for ethylene copolymerization with Ziegler–Natta catalysts contain many kinetic rate constants. Precise estimates of key parameters are required if the models are to be used to obtain reliable predictions of polymer properties for a specified catalyst over a range of polymerization conditions. In this paper, a novel method is developed to assist modelers in assessing whether their model parameters will be estimable from existing or proposed experimental data, and in determining subsets of influential parameters that can be estimated from the data when the complete set of model parameters cannot be estimated. The effects of using different types of data, varying the number of observations per experimental run, and increasing the number of experimental runs on the number of estimable parameters are considered. A method for comparison of the relative effectiveness of different experimental designs for estimating key parameters in gas‐phase ethylene copolymerization is also presented.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“These methods are appropriate if functional relations h between the parameters emerging from structural non-identifiability are linear.This is often not the case for reaction networks modeled by ODE, because observables depend non-linearly on the parameters.Practical non-identifiability cannot be detected, because a quadratic approximation is not able to explain increasing but limited behavior of”
From Structural and practical identifiability analysis of partially observed dynamical models by exploiting the profile likelihood (2009) · cites this paper as Yao et al., 2003
Citations
Cites
Introduction to Linear Regression Analysis.
Assuncao, R., Sampson, P. D., Montgomery, D. C., & Peck, E. A. (1993) · Journal of the American Statistical Association · doi:10.2307/2290746 · Cited by 5,388
Nonlinear Regression Analysis and Its Applications
Bates, D. M., & Watts, D. G. (1988) · Wiley Series in Probability and Statistics · doi:10.1002/9780470316757 · Cited by 3,979
Nonlinear Parameter Estimation
Chambers, J. M., & Bard, Y. (1975) · Technometrics · doi:10.2307/1268363 · Cited by 2,158
Nonlinear Parameter Estimation
Brubaker, T. A., & O'Keefe, K. R. (1979) · Analytical Chemistry · doi:10.1021/ac50049a796 · Cited by 2,134
Parameter Estimation in Engineering and Science
de Oliveira, J. T., Beck, J. V., & Arnold, K. J. (1979) · International Statistical Review / Revue Internationale de Statistique · doi:10.2307/1403212 · Cited by 1,480 · cited 3×
“6 is equivalent to scaling by the standard deviations (Beck and Arnold, 1977).”
BackgroundInfluentialIntroduction to Linear Regression Analysis
Gray, J. B. (2002) · Technometrics · doi:10.1198/tech.2002.s714 · Cited by 943
DESIGN OF EXPERIMENTS IN NON-LINEAR SITUATIONS
BOX, G. E. P., & LUCAS, H. L. (1959) · Biometrika · doi:10.1093/biomet/46.1-2.77 · Cited by 738 · cited 2×
“The widely used D-optimality design criterion (Box and Lucas, 1959), which directly minimizes the size of the JCR, can be written as:”
MethodParameter Estimation in Engineering and Science.
Folks, J. L., Beck, J. V., & Arnold, K. J. (1978) · Journal of the Royal Statistical Society. Series A (General) · doi:10.2307/2344460 · Cited by 610
The Bayesian estimation of common parameters from several responses
BOX, G. E. P., & DRAPER, N. R. (1965) · Biometrika · doi:10.1093/biomet/52.3-4.355 · Cited by 304
Identifiability of State Space Models
Walter, E. (1982) · Lecture Notes in Biomathematics · doi:10.1007/978-3-642-61823-9 · Cited by 278 · cited 1×
“Estimability is closely linked with sensitivity analysis (Walter, 1982).”
Background
Research works printed but not linked: 9
- Haskins G. D., 1999, M.Sc. thesis
- Klaus R. A., 1981, Ph. D. thesis
- Kou B., 2003, Ph.D. thesis
- Pigeon M. G., 1996, PhD thesis
- Seber G. A.F., 1989, Nonlinear Regression, Wiley Series in Probability and Mathematical Statistics: Probability and Mathematical Statistics
- Shaw B. M., 1999, Ph.D. thesis
- Soares J. B.P., 1995, Polym. React. Eng., 3, 261
- Stewart W. E., 1995, GREG: A Fortran Subroutine for Nonlinear Regression and Experimental Design, User's Manual
- Williams C. H., 1996, Master's thesis
Cited by
Raue, A., Kreutz, C., Maiwald, T., Bachmann, J., Schilling, M., Klingmüller, U., & Timmer, J. (2009) · Bioinformatics · doi:10.1093/bioinformatics/btp358 · Cited by 1,442
On Identifiability of Nonlinear ODE Models and Applications in Viral Dynamics
Miao, H., Xia, X., Perelson, A. S., & Wu, H. (2011) · SIAM Review · doi:10.1137/090757009 · Cited by 610
“[120], the norm ‖Sh ‖ was proposed as the measurement of nearly linear dependency between the vector Sh and the vector space VSI , since the shorter the distance, the larger the dependence.”
BackgroundMethodLinking data to models: data regression
Jaqaman, K., & Danuser, G. (2006) · Nature Reviews Molecular Cell Biology · doi:10.1038/nrm2030 · Cited by 243
“Given the structure of a model, is it possible to uniquely estimate its unknown parameters? What experimental data are required to achieve unique parameter identificatio”
BackgroundAdvances and selected recent developments in state and parameter estimation
Kravaris, C., Hahn, J., & Chu, Y. (2013) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2012.06.001 · Cited by 177
“The technique was originally presented as a heuristic method (Yao et al., 2003) and later identified as a forward selection which maximizes the D-criterion (Chu & Hahn, 2007).”
McLean, K. A. P., & McAuley, K. B. (2012) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.20660 · Cited by 166
Self-citationIterative approach to model identification of biological networks
Gadkar, K. G., Gunawan, R., & Doyle, F. J. (2005) · BMC Bioinformatics · doi:10.1186/1471-2105-6-155 · Cited by 156
Addressing parameter identifiability by model-based experimentation
Raue, A., Kreutz, C., Maiwald, T., Klingmüller, U., & Timmer, J. (2011) · IET Systems Biology · doi:10.1049/iet-syb.2010.0061 · Cited by 145
“in [26–29].”
BackgroundYue, H., Brown, M., Knowles, J., Wang, H., Broomhead, D. S., & Kell, D. B. (2006) · Molecular BioSystems · doi:10.1039/b609442b · Cited by 148
Quaiser, T., & Mönnigmann, M. (2009) · BMC Systems Biology · doi:10.1186/1752-0509-3-50 · Cited by 114
“We presented a detailed comparison of the proposed eigenvalue approach to three established methods for identifiability testing, namely, the correlation method [25], the PCA based method [27], and the orthogonal method [24].”
BackgroundMethodInfluentialNonlinear ill-posed problem analysis in model-based parameter estimation and experimental design
C., D. C. L., Barz, T., Körkel, S., & Wozny, G. (2015) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2015.03.002 · Cited by 124
Point-of-care biomarker quantification enabled by sample-specific calibration
McNerney, M. P., Zhang, Y., Steppe, P., Silverman, A. D., Jewett, M. C., & Styczynski, M. P. (2019) · Science Advances · doi:10.1126/sciadv.aax4473 · Cited by 92
Model identification of signal transduction networks from data using a state regulator problem.
Gadkar, K. G., Doyle III, F. J., & Varner, J. (2005) · Systems Biology · doi:10.1049/sb:20045029 · Cited by 75
Wu, S.-H., McLean, K. A. P., Harris, T. J., & McAuley, K. B. (2011) · International Journal of Advanced Mechatronic Systems · doi:10.1504/ijamechs.2011.042615 · Cited by 77
Self-citationParameter set selection for estimation of nonlinear dynamic systems
Chu, Y., & Hahn, J. (2007) · AIChE Journal · doi:10.1002/aic.11295 · Cited by 79
Parameter Estimation in a Simplified MWD Model for HDPE Produced by a Ziegler‐Natta Catalyst
Thompson, D. E., McAuley, K. B., & McLellan, P. J. (2009) · Macromolecular Reaction Engineering · doi:10.1002/mren.200800052 · Cited by 73
Self-citationIdentification of parameter correlations for parameter estimation in dynamic biological models
Li, P., & Vu, Q. D. (2013) · BMC Systems Biology · doi:10.1186/1752-0509-7-91 · Cited by 83
“[21] used the rank of the sensitivity matrix to determine the number of estimable parameters.”
BackgroundMethodParameter identifiability of power-law biochemical system models
Srinath, S., & Gunawan, R. (2010) · Journal of Biotechnology · doi:10.1016/j.jbiotec.2010.02.019 · Cited by 68
Chu, Y., & Hahn, J. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie800432s · Cited by 69
“…method (Velez-Reyes and Verghese, 1995), an extension of the relative gain array (Sandink et al., 2001), a Gram-Schmidt orthogonalization method (Yao et al., 2003), a recursive approach based upon principal component analysis (Li et al., 2004) and a combination of Hankel singular value and…”
MethodKou, B., McAuley, K. B., Hsu, C., Bacon, D. W., & Yao, K. Z. (2005) · Industrial & Engineering Chemistry Research · doi:10.1021/ie048957o · Cited by 66
Self-citationBui, L. H. T., Chakrabarti, R., & Bhan, A. (2016) · ACS Catalysis · doi:10.1021/acscatal.6b01830 · Cited by 63
Baij, L., Hermans, J. J., Keune, K., & Iedema, P. D. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b00890 · Cited by 62
Fysikopoulos, D., Benyahia, B., Borsos, Á., Nagy, Z. K., & Rielly, C. D. (2018) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2018.09.007 · Cited by 66
Mean-Squared-Error Methods for Selecting Optimal Parameter Subsets for Estimation
McLean, K. A. P., Wu, S.-H., & McAuley, K. B. (2012) · Industrial & Engineering Chemistry Research · doi:10.1021/ie202352f · Cited by 55
Self-citationWu, S.-H., McAuley, K. B., & Harris, T. J. (2011) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.20479 · Cited by 55
Self-citationIdentifiability and estimability study for a dynamic solid oxide fuel cell model
Jayasankar, B. R., Ben‐Zvi, A., & Huang, B. (2008) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2008.11.005 · Cited by 50
“To assess the estimability of the system under noisy onditions, a cut-off value, for the sensitivity coefficients, below hich the parameters would be deemed inestimable was set at .04 (Yao et al., 2003).”
BackgroundMethodInfluentialKou, B., McAuley, K. B., Hsu, J. C. C., & Bacon, D. W. (2005) · Macromolecular Materials and Engineering · doi:10.1002/mame.200400392 · Cited by 48
Self-citationExperimental evaluation of an approach to online redesign of experiments for parameter determination
Barz, T., C., D. C. L., Arellano‐García, H., & Wozny, G. (2012) · AIChE Journal · doi:10.1002/aic.13957 · Cited by 54
Benyahia, B., Latifi, M. A., Fonteix, C., & Pla, F. (2012) · Chemical Engineering Science · doi:10.1016/j.ces.2012.12.013 · Cited by 54
“Instead, the cut-off value can be specified arbitrarily a priori (Yao et al. (2003)) or refined with respect to the value of the objective function for the parameter estimation (Wu et al. (2011), Littlejohns et al. (2010)).”
BackgroundMethodInfluentialSun, C., & Hahn, J. (2006) · Chemical Engineering Science · doi:10.1016/j.ces.2006.04.027 · Cited by 47
Generating Effective Models and Parameters for RNA Genetic Circuits
Hu, C. Y., Varner, J. D., & Lucks, J. B. (2015) · ACS Synthetic Biology · doi:10.1021/acssynbio.5b00077 · Cited by 58
C., D. C. L., Barz, T., Peñuela, M., Quiceno, A. P. V., Ochoa, S., & Wozny, G. (2013) · Biotechnology Progress · doi:10.1002/btpr.1753 · Cited by 51
Pyomo.DOE : An open‐source package for model‐based design of experiments in Python
Wang, J., & Dowling, A. W. (2022) · AIChE Journal · doi:10.1002/aic.17813 · Cited by 58
Simultaneous model identification and optimization in presence of model-plant mismatch
Mandur, J. S., & Budman, H. M. (2015) · Chemical Engineering Science · doi:10.1016/j.ces.2015.02.038 · Cited by 42
Chu, Y., & Hahn, J. (2008) · AIChE Journal · doi:10.1002/aic.11562 · Cited by 41
Model for a solid–liquid stirred tank two-phase partitioning bioscrubber for the treatment of BTEX
Littlejohns, J. V., McAuley, K. B., & Daugulis, A. J. (2009) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2009.10.091 · Cited by 41
Self-citationImproving prediction capabilities of complex dynamic models via parameter selection and estimation
Chu, Y., Huang, Z. J., & Hahn, J. (2009) · Chemical Engineering Science · doi:10.1016/j.ces.2009.06.057 · Cited by 40
Parameter estimation of kinetic models from metabolic profiles: two-phase dynamic decoupling method
Jia, G., Stephanopoulos, G. N., & Gunawan, R. (2011) · Bioinformatics · doi:10.1093/bioinformatics/btr293 · Cited by 43
Simultaneous State and Parameter Estimation: The Role of Sensitivity Analysis
Liu, J., Gnanasekar, A., Zhang, Y., Bo, S., Liu, J., Hu, J., & Zou, T. (2021) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.0c03793 · Cited by 38
Modeling and optimization of a seeded suspension polymerization process
Lin, W., Biegler, L. T., & Jacobson, A. M. (2010) · Chemical Engineering Science · doi:10.1016/j.ces.2010.03.052 · Cited by 38
Lei, M., Vallières, C., Grévillot, G., & Latifi, M. A. (2013) · Industrial & Engineering Chemistry Research · doi:10.1021/ie3029152 · Cited by 42
C., D. C. L., Wozny, G., Flores‐Tlacuahuac, A., Vasquez-Medrano, R. C., & Zavala, V. M. (2016) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.5b03910 · Cited by 39
Mathematical Modeling of RNA-Based Architectures for Closed Loop Control of Gene Expression
Agrawal, D. K., Tang, X., Westbrook, A. M., Marshall, R., Maxwell, C. S., Lucks, J. B., Noireaux, V., Beisel, C. L., Dunlop, M. J., & Franco, E. (2018) · ACS Synthetic Biology · doi:10.1021/acssynbio.8b00040 · Cited by 42
On the drying rates of individual iron oxide pellets
Tsukerman, T., Duchesne, C., & Hodouin, D. (2007) · International Journal of Mineral Processing · doi:10.1016/j.minpro.2007.06.004 · Cited by 36
Shahmohammadi, A., & McAuley, K. B. (2018) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.8b03047 · Cited by 39
Self-citationAnalysis of an industrial adsorption process based on ammonia chemisorption: Modeling and simulation
Cardenas, C., Latifi, M. A., Vallières, C., Marsteau, S., & Sigot, L. (2021) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2021.107474 · Cited by 39
Woloszyn, J. D., & McAuley, K. B. (2011) · Macromolecular Reaction Engineering · doi:10.1002/mren.201100021 · Cited by 34
Self-citationParameter subset selection techniques for problems in mathematical biology
Olsen, C. H., Ottesen, J. T., Smith, R. C., & Olufsen, M. S. (2018) · Biological Cybernetics · doi:10.1007/s00422-018-0784-8 · Cited by 34
Mean squared error criterion for model-based design of experiments with subset selection
Kim, B., Ryu, K. H., & Heo, S. (2022) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2022.107667 · Cited by 35
Quaiser, T., Dittrich, A., Schaper, F., & Mönnigmann, M. (2011) · BMC Systems Biology · doi:10.1186/1752-0509-5-30 · Cited by 43
“Methods for at-a-point identifiability testing [1,3,4,18-22], in contrast, are easier to implement and more widely * Correspondence: martin.”
MethodChen, K., Mehdiabadi, S., Liu, B., & Soares, J. B. P. (2016) · Macromolecular Reaction Engineering · doi:10.1002/mren.201600003 · Cited by 31
Using prior parameter knowledge in model‐based design of experiments for pharmaceutical production
Shahmohammadi, A., & McAuley, K. B. (2020) · AIChE Journal · doi:10.1002/aic.17021 · Cited by 32
Self-citationWu, Y., Figueira, F. L., Steenberge, P. H. M. V., D’hooge, D., Zhou, Y., & Luo, Z. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.130463 · Cited by 32
Maheshwari, V., Lakshminarayanan, S., & Rangaiah, G. P. (2011) · Annals of Biomedical Engineering · doi:10.1007/s10439-011-0383-5 · Cited by 30
Ngo, V. V., Michel, J., Gujisaite, V., Latifi, M. A., & Simonnot, M. (2014) · Journal of Contaminant Hydrology · doi:10.1016/j.jconhyd.2014.01.005 · Cited by 31
“For doing so, we applied an estimability method developed by Yao et al. (2003) to look for insight into the above factors based on the available data collected from the experiments under saturated and unsaturated flow conditions.”
BackgroundMethodInfluentialCampbell, D., & Lele, S. R. (2013) · Computational Statistics & Data Analysis · doi:10.1016/j.csda.2013.09.013 · Cited by 32
“Assessing practical identifiability is commonly performed using artificial data sets based on a-priori parameter values to explore the sensitivity of the MLE to data uncertainty (Yao et al. 2003 and Anh et al. 2006).”
MethodMiller, J. H., Bui, L. H. T., & Bhan, A. (2019) · Reaction Chemistry & Engineering · doi:10.1039/c8re00285a · Cited by 29
Bouchkira, I., Latifi, M. A., Khamar, L., & Benjelloun, S. (2020) · Reliability Engineering & System Safety · doi:10.1016/j.ress.2020.107263 · Cited by 31
Robust batch‐to‐batch optimization in the presence of model‐plant mismatch and input uncertainty
Hille, R., Mandur, J. S., & Budman, H. M. (2017) · AIChE Journal · doi:10.1002/aic.15645 · Cited by 28
Yoo, S. J., Kim, J. H., & Lee, J. M. (2014) · Bioresource Technology · doi:10.1016/j.biortech.2014.03.128 · Cited by 34
Parameters estimation and model discrimination for solid-liquid reactions in batch processes
Wang, Y., Biegler, L. T., Patel, M., & Wassick, J. M. (2018) · Chemical Engineering Science · doi:10.1016/j.ces.2018.05.040 · Cited by 28
Selection of simplified models: I. Analysis of model‐selection criteria using mean‐squared error
Wu, S., McAuley, K. B., & Harris, T. J. (2010) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.20406 · Cited by 27
Self-citationNogueira, I. B. R., Fontes, C. H., Sartori, I., Pontes, K. V., & Embiruçu, M. (2017) · Computers & Industrial Engineering · doi:10.1016/j.cie.2017.01.030 · Cited by 31
Zhang, C., Shao, Z., Chen, X., Yao, Z., Gu, X., & Biegler, L. T. (2014) · AIChE Journal · doi:10.1002/aic.14527 · Cited by 30
“1ktM j ð Þ M 1⁄2 RLY j ð Þ2KTD j ð ÞY(1) j ð Þ (15)”
Modeling of equilibrium water vapor adsorption isotherms on activated carbon, alumina and hopcalite
Cardenas, C., Farrusseng, D., Daniel, C., & Aubry, R. (2022) · Fluid Phase Equilibria · doi:10.1016/j.fluid.2022.113520 · Cited by 29
Model re-parameterization and output prediction for a bioreactor system
Surisetty, K., Siegler, H. D. L. H., McCaffrey, W. C., & Ben‐Zvi, A. (2010) · Chemical Engineering Science · doi:10.1016/j.ces.2010.04.024 · Cited by 27
Jang, S. S., & Gopaluni, R. B. (2011) · Chemical Engineering Science · doi:10.1016/j.ces.2011.03.029 · Cited by 25
Koeva, V. I., Daneshvar, S., Senden, R. J., Imam, A. H. M., Schreiner, L. J., & McAuley, K. B. (2009) · Macromolecular Theory and Simulations · doi:10.1002/mats.200900023 · Cited by 25
“To select an appropriate subset for estimation we used a parameter estimability algorithm([24-26]) to rank the parameters from most estimable to least estimable.”
BackgroundMethodSelf-citationPuskas, J. E., Shaikh, S. K., Yao, K. Z., McAuley, K. B., & Kaszás, G. (2004) · European Polymer Journal · doi:10.1016/j.eurpolymj.2004.08.006 · Cited by 24
Self-citationParameter Selection and Estimation Techniques in a Styrene Polymerization Model
Woloszyn, J. D., Hesse, P., Hungenberg, K., & McAuley, K. B. (2013) · Macromolecular Reaction Engineering · doi:10.1002/mren.201200074 · Cited by 24
Self-citationModeling of Slurry Polymerization of Ethylene Using a Soluble Cp2ZrCl2/MAO Catalytic System
Ahmadi, M., Nekoomanesh, M., Jamjah, R., Zohuri, G., & Arabi, H. (2007) · Macromolecular Theory and Simulations · doi:10.1002/mats.200700010 · Cited by 24
Bouchkira, I., Latifi, M. A., Khamar, L., & Benjelloun, S. (2021) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2021.107536 · Cited by 25
Kinetics and mechanisms in carbocationic polymerization: The quest for true rate constants
Puskas, J. E., Chan, S. W. P., McAuley, K. B., Shaikh, S. K., & Kaszás, G. (2005) · Journal of Polymer Science Part A Polymer Chemistry · doi:10.1002/pola.21011 · Cited by 23
Self-citationA unified framework for estimating parameters of kinetic biological models
Baker, S. M., Poskar, C. H., Schreiber, F., & Junker, B. H. (2015) · BMC Bioinformatics · doi:10.1186/s12859-015-0500-9 · Cited by 24
“This effect is minimal due to the lower sensitivity of these parameters on the system output [26].”
BackgroundMethodInfluentialChu, Y., & Hahn, J. (2011) · AIChE Journal · doi:10.1002/aic.12727 · Cited by 26
Zhan, Z., Fang, B., Wan, S., Bai, Y., Hong, J., & Li, X. (2024) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2024.03.036 · Cited by 22
Lee, D., Ding, Y., Jayaraman, A., & Kwon, J. S. (2018) · Processes · doi:10.3390/pr6030021 · Cited by 25
Onyemelukwe, I. I., Benyahia, B., Reis, N. M., Nagy, Z. K., & Rielly, C. D. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.015 · Cited by 22
Shahmohammadi, A., & McAuley, K. B. (2019) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2019.06.029 · Cited by 26
Self-citationRisk mitigation in model-based experiment design: A continuous-effort approach to optimal campaigns
Kusumo, K. P., Kuriyan, K., Vaidyaraman, S., García‐Muñoz, S., Shah, N., & Chachuat, B. (2022) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2022.107680 · Cited by 22
Estimability Analysis and Optimisation of Soil Hydraulic Parameters from Field Lysimeter Data
Ngo, V. V., Latifi, M. A., & Simonnot, M. (2013) · Transport in Porous Media · doi:10.1007/s11242-013-0155-9 · Cited by 21
“Therefore, the use of the estimability analysis method of Yao et al. (2003) allows us not only to rank the estimability order of parameters but also to evaluate possible correlations among them, for a given experimental condition.”
BackgroundMethodInfluentialEghtesadi, Z., & McAuley, K. B. (2014) · Industrial & Engineering Chemistry Research · doi:10.1021/ie5002444 · Cited by 22
Self-citationZhu, Y., & Huang, B. (2010) · AIChE Journal · doi:10.1002/aic.12479 · Cited by 20
Modelling coke formation in an industrial ethane‐cracking furnace for ethylene production
Karimi, H., Olayiwola, B. O., Farag, H., & McAuley, K. B. (2019) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.23619 · Cited by 20
Self-citationSensitivity and identifiability analysis of COVID-19 pandemic models
Игоревна, К. О., Kabanikhin, S. I., Sosnovskaya, M. I., & Andornaya, D. V. (2021) · Vavilov Journal of Genetics and Breeding · doi:10.18699/vj21.010 · Cited by 25
Müller, D., Esche, E., C., D. C. L., & Wozny, G. (2014) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2014.07.007 · Cited by 21
“…et al., 2013), (Velez-Reyes & Verghese, 1995), (Grah, 2004), and (Quaiser & Monnigmann, 2009) and a focus on the sensitivities of identifiable parameters is made in (Brun et al., 2002), (Chu & Hahn, 2009), (Yao et al., 2003), (Chandrakant & Bisaria, 1998), and (Weijers & Vanrolleghem, 1997).”
Dobre, S., Bastogne, T., Profeta, C., Barberi‐Heyob, M., & Richard, A. (2012) · Automatica · doi:10.1016/j.automatica.2012.05.004 · Cited by 23
“Indeed, while the relationship between local sensitivity and identifiability analysis, through the Fisher information matrix, is clearly established [3,31,33], the link between global studies is less obvious.”
BackgroundZhao, Y. R., Arriola, D. J., Puskas, J. E., & McAuley, K. B. (2016) · Macromolecular Theory and Simulations · doi:10.1002/mats.201600004 · Cited by 19
Self-citationIedema, P. D., Schamboeck, V., Boonen, H., Koskamp, J. A., Schellekens, S., & Willemse, R. X. E. (2017) · Chemical Engineering Science · doi:10.1016/j.ces.2017.11.009 · Cited by 19
Feng, H.-H., Chen, X., Gu, X., Feng, L., Wang, D.-F., Yang, G., Gao, Y., Zhang, C., & Hu, G. (2022) · Chemical Engineering Science · doi:10.1016/j.ces.2022.117952 · Cited by 20
Lee, D., Singla, A., Wu, H., & Kwon, J. S. (2018) · AIChE Journal · doi:10.1002/aic.16209 · Cited by 21
Gene-Centric Model Approaches for Accurate Prediction of Pesticide Biodegradation in Soils
Rodríguez, L. C., Ingalls, B., Schwarz, E., Streck, T., Uksa, M., & Pagel, H. (2020) · Environmental Science & Technology · doi:10.1021/acs.est.0c03315 · Cited by 21
Temperature and soil moisture change microbial allocation of pesticide‐derived carbon
Wirsching, J., Rodríguez, L. C., Ditterich, F., Pagel, H., He, R., Uksa, M., Zwiener, C., Kandeler, E., & Poll, C. (2023) · European Journal of Soil Science · doi:10.1111/ejss.13417 · Cited by 19
“We complemented our model calibration with a local sensitivity analysis of our parameter fits through the sensitivity coefficient (Ingalls, 2008; Zi, 2011), identifiability score (Malwade et al., 2017; Yao et al., 2003), and error (Malwade et al., 2017) of estimated parameters.”
MethodRobust modeling of a microalgal heterotrophic fed-batch bioreactor
Surisetty, K., Siegler, H. D. L. H., McCaffrey, W. C., & Ben‐Zvi, A. (2010) · Chemical Engineering Science · doi:10.1016/j.ces.2010.06.008 · Cited by 19
Nogueira, I. B. R., & Pontes, K. V. (2016) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2016.10.013 · Cited by 18
Balakrishnan, N. P., Lakshminarayanan, S., & Rangaiah, G. P. (2014) · Journal of Theoretical Biology · doi:10.1016/j.jtbi.2014.04.038 · Cited by 19
Ahmadi, M., Nekoomanesh, M., & Arabi, H. (2009) · Macromolecular Theory and Simulations · doi:10.1002/mats.200800088 · Cited by 18
Mathematical Model of Polyether Production From 1,3‐Propanediol
Cui, W. J., McAuley, K. B., Whitney, R. A., Spence, R. E. V. H., & Xie, T. (2013) · Macromolecular Reaction Engineering · doi:10.1002/mren.201200068 · Cited by 18
Self-citationA kinetic model for propylene oxidation on a mixed metal oxide catalyst
Bui, L. H. T., & Bhan, A. (2018) · Applied Catalysis A General · doi:10.1016/j.apcata.2018.07.004 · Cited by 18
Modeling of sequence length distribution for olefin copolymerization with vanadium‐based catalyst
Cheng, X., Feng, L., Gu, X., Chen, X., Liu, Z., & McAuley, K. B. (2019) · AIChE Journal · doi:10.1002/aic.16784 · Cited by 18
Self-citationMathematical Modeling of Arborescent Polyisobutylene Production in Batch Reactors
Zhao, Y. R., McAuley, K. B., Puskas, J. E., Santos, L. M. D., & Alvarez, A. (2013) · Macromolecular Theory and Simulations · doi:10.1002/mats.201200058 · Cited by 17
Self-citation
Metadata
- Authors
- Yao, K. Z., Shaw, B. M., Kou, B., McAuley, K. B., & Bacon, D. W.
- Affiliations
- Queen's University (CA)
- a Department of Chemical Engineering , Queen's University , Kingston , Ontario , K7L 3N6 , Canada
- ORCID
- Kou, Bo
- Venue
- Polymer Reaction Engineering
- Publisher
- Informa UK Limited
- Published
- 2003-01-09
- Volume
- 11
- Issue
- 3
- Pages
- 563-588
- ISSN
- 1054-3414 (ISSN-L)
- 1532-2408
- OpenAlex
- W1967988563
- Cited by
- 290
- References
- 34
- Citations by year
- 2026: 5 · 2025: 13 · 2024: 13 · 2023: 23 · 2022: 16 · 2021: 19 · 2020: 21 · 2019: 15 · 2018: 24 · 2017: 9 · 2016: 14 · 2015: 12 · 2014: 14 · 2013: 15 · 2012: 13
- FWCI
- 2.82
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Polymer Reaction Engineering (publishedVersion)
- Funders
- Government of Ontario
- Natural Sciences and Engineering Research Council of Canada
- Topics
- Physical Sciences › Chemistry › Organic Chemistry › Organometallic Complex Synthesis and Catalysis
- Social Sciences › Decision Sciences › Management Science and Operations Research › Optimal Experimental Design Methods
- Physical Sciences › Engineering › Control and Systems Engineering › Control Systems and Identification
- Keywords
- Ziegler-Natta catalysts, parameter estimability, experimental design, rate constants, gas-phase polymerization, polymerization kinetics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.