Modeling ethylene/butene copolymerization with multi-site catalysts: parameter estimability and experimental design
The DOI matches its Crossref record; 33 of the 34 references it cites were found in a registry or an index.
Abstract
Mechanistic models for ethylene copolymerization with Ziegler–Natta catalysts contain many kinetic rate constants. Precise estimates of key parameters are required if the models are to be used to obtain reliable predictions of polymer properties for a specified catalyst over a range of polymerization conditions. In this paper, a novel method is developed to assist modelers in assessing whether their model parameters will be estimable from existing or proposed experimental data, and in determining subsets of influential parameters that can be estimated from the data when the complete set of model parameters cannot be estimated. The effects of using different types of data, varying the number of observations per experimental run, and increasing the number of experimental runs on the number of estimable parameters are considered. A method for comparison of the relative effectiveness of different experimental designs for estimating key parameters in gas‐phase ethylene copolymerization is also presented.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“These methods are appropriate if functional relations h between the parameters emerging from structural non-identifiability are linear.This is often not the case for reaction networks modeled by ODE, because observables depend non-linearly on the parameters.Practical non-identifiability cannot be detected, because a quadratic approximation is not able to explain increasing but limited behavior of”
From Structural and practical identifiability analysis of partially observed dynamical models by exploiting the profile likelihood (2009) · cites this paper as Yao et al., 2003
Citations
Cites
Introduction to Linear Regression Analysis.
Assuncao, R., Sampson, P. D., Montgomery, D. C., & Peck, E. A. (1993) · Journal of the American Statistical Association · doi:10.2307/2290746 · Cited by 5,388
Nonlinear Regression Analysis and Its Applications
Bates, D. M., & Watts, D. G. (1988) · Wiley Series in Probability and Statistics · doi:10.1002/9780470316757 · Cited by 3,979
Nonlinear Parameter Estimation
Chambers, J. M., & Bard, Y. (1975) · Technometrics · doi:10.2307/1268363 · Cited by 2,158
Nonlinear Parameter Estimation
Brubaker, T. A., & O'Keefe, K. R. (1979) · Analytical Chemistry · doi:10.1021/ac50049a796 · Cited by 2,134
Parameter Estimation in Engineering and Science
de Oliveira, J. T., Beck, J. V., & Arnold, K. J. (1979) · International Statistical Review / Revue Internationale de Statistique · doi:10.2307/1403212 · Cited by 1,480 · cited 3×
“6 is equivalent to scaling by the standard deviations (Beck and Arnold, 1977).”
BackgroundInfluentialIntroduction to Linear Regression Analysis
Gray, J. B. (2002) · Technometrics · doi:10.1198/tech.2002.s714 · Cited by 943
DESIGN OF EXPERIMENTS IN NON-LINEAR SITUATIONS
BOX, G. E. P., & LUCAS, H. L. (1959) · Biometrika · doi:10.1093/biomet/46.1-2.77 · Cited by 738 · cited 2×
“The widely used D-optimality design criterion (Box and Lucas, 1959), which directly minimizes the size of the JCR, can be written as:”
MethodParameter Estimation in Engineering and Science.
Folks, J. L., Beck, J. V., & Arnold, K. J. (1978) · Journal of the Royal Statistical Society. Series A (General) · doi:10.2307/2344460 · Cited by 610
The Bayesian estimation of common parameters from several responses
BOX, G. E. P., & DRAPER, N. R. (1965) · Biometrika · doi:10.1093/biomet/52.3-4.355 · Cited by 304
Identifiability of State Space Models
Walter, E. (1982) · Lecture Notes in Biomathematics · doi:10.1007/978-3-642-61823-9 · Cited by 278 · cited 1×
“Estimability is closely linked with sensitivity analysis (Walter, 1982).”
Background
Research works printed but not linked: 9
- Haskins G. D., 1999, M.Sc. thesis
- Klaus R. A., 1981, Ph. D. thesis
- Kou B., 2003, Ph.D. thesis
- Pigeon M. G., 1996, PhD thesis
- Seber G. A.F., 1989, Nonlinear Regression, Wiley Series in Probability and Mathematical Statistics: Probability and Mathematical Statistics
- Shaw B. M., 1999, Ph.D. thesis
- Soares J. B.P., 1995, Polym. React. Eng., 3, 261
- Stewart W. E., 1995, GREG: A Fortran Subroutine for Nonlinear Regression and Experimental Design, User's Manual
- Williams C. H., 1996, Master's thesis
Cited by
Items 201–289 of 289
Santos, R. V. A., Rebello, C. M., Prudente, A. N., Santana, V. V., Ferreira, A. F. P., Ribeiro, A. M., Pontes, K. V., & Nogueira, I. B. R. (2023) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.3c02162 · Cited by 4
Parameter Subset Selection in Differential Equation Models with Dead Time
Vo, A. D., Elraghy, A., & McAuley, K. B. (2018) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2018.09.348 · Cited by 4
“The methodology builds on earlier algorithms for ranking model parameters in systems without time delay (Yao et al., 2003; Thompson et al., 2009) and for finding the optimum number of parameters for estimation (Wu et al., 2011; McLean and McAuley, 2012a).”
MethodSelf-citationA procedure for ranking parameter importance for estimation in predictive mechanistic models
Elevitch, C. R., & Johnson, C. R. (2020) · Ecological Modelling · doi:10.1016/j.ecolmodel.2020.108948 · Cited by 6
Gibson, L. A., Aiello, J. P., Jiang, Y., Boller, T., & McAuley, K. B. (2022) · Macromolecular Theory and Simulations · doi:10.1002/mats.202200023 · Cited by 4
Self-citationNgo, V. V., Michel, J., Lucas, L., Latifi, M. A., & Simonnot, M. (2014) · European Journal of Environmental and Civil engineering · doi:10.1080/19648189.2014.950759 · Cited by 4
“This numerical study showed that the estimability method of Yao et al. (2003) is useful for the evaluation of information content, correlation among parameters and prediction of limitation point of the breakthrough data.”
MethodInfluentialStructured model and parameter estimation in plant cell cultures of Thevetia peruviana
Quiceno, A. P. V., Arias, J. P., Aragón, D., Ochoa, S., & Arias, M. (2016) · Bioprocess and Biosystems Engineering · doi:10.1007/s00449-016-1722-6 · Cited by 5
Analysis of an industrial adsorption process based on ammonia chemisorption: model validation
Cardenas, C., Latifi, M. A., Vallières, C., & Marsteau, S. (2022) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-323-95879-0.50077-1 · Cited by 3
Agyeman, B. T., Orouskhani, E., Naouri, M., Appels, W. M., Wolleben, M., Liu, J., & Shah, S. L. (2025) · Control Engineering Practice · doi:10.1016/j.conengprac.2025.106593 · Cited by 3
“To address the limitations associated with post-estimation indentifiablity assessments, several studies in the general context of state and parameter estimation have advocated for assessing parameter identifiability prior to model calibration [18, 19].”
InfluentialImproved Parameter Estimation of Ill-Conditioned Problems
Kim, B., & Lee, J. H. (2018) · IEEE Conference on Decision and Control (CDC) · doi:10.1109/cdc.2018.8619123 · Cited by 3
“For example, the orthogonalization method, which is the most widely used, determines the selected parameters to estimate based on the norm and linear dependence of sensitivity vectors [6].”
MethodLi, H., & Zhang, E. (2021) · Water · doi:10.3390/w13212996 · Cited by 4
“When a specific mathematical model and the total number of samples are given, non-uniform sampling under this D-optimal designs will optimize sampling time and then arrange the number of repeated samplings corresponding to each sampling time [16,30,31].”
BackgroundPawar, S. R., Rapp, E. S., Gohean, J. R., & Longoria, R. G. (2021) · Journal of Engineering and Science in Medical Diagnostics and Therapy · doi:10.1115/1.4053065 · Cited by 6
Wang, L., & Qi, J. (2024) · IEEE Access · doi:10.1109/access.2024.3481318 · Cited by 7
“Note that the COP approach is much more time efficient than the forward selection method in [9].”
MethodModeling and Optimization of a Semi-Interpenetrating Polymer Network Process
Lin, W. (2011) · KiltHub Repository · doi:10.1184/r1/6720665 · Cited by 3
Shahmohammadi, A., & Bonnecaze, R. T. (2020) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2020.04.032 · Cited by 4
Identifiability analysis of an electrochemical model of li-ion battery
Samadi, M. F., & Saif, M. (2016) · Proceedings of the ... American Control Conference/Proceedings of the American Control Conference · doi:10.1109/acc.2016.7525395 · Cited by 3
“al [17], is a methodology that ranks the model parameters by analyzing”
MethodSIGNET: Boolean rule determination for abscisic acid signaling
Jenkins, J. W. (2008) · Cited by 3
Sensitivity Analysis for Global Parameter Identification. Application to Aerodynamic Coefficients
Albisser, M., & Dobre, S. (2018) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2018.09.069 · Cited by 3
Design of Experiments and Sensitivity Analysis for Microalgal Bioreactor Systems
Yoo, S. J., Oh, S.-K., & Lee, J. M. (2012) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-444-59520-1.50003-8 · Cited by 3
Kabanikhin, S. I., Bektemessov, M. A., Игоревна, К. О., & Bektemessov, Z. M. (2019) · International Journal of Mathematics and Physics · doi:10.26577/ijmph-2019-i1-5 · Cited by 3
“[6], more precisely, in this work, by the method of eigenvalues [7-8], we will determine only 4 identifiable parameters � � (�, ��, ��, ��)� from additional statistical information.”
Amato, M., Giménez, D., Kannepalli, S., Strom, P. F., Krogmann, U., & Miskewitz, R. (2020) · Journal of Environmental Management · doi:10.1016/j.jenvman.2020.110379 · Cited by 3
OBTAINING THE BEST MODEL PREDICTIONS AND PARAMETER ESTIMATES USING LIMITED DATA
McLean, K. A. P. (2011) · QSpace (Queen's University Library) · Cited by 6
Kim, Y. (2014) · Deep Blue (University of Michigan) · Cited by 4
Agyeman, B. T., Orouskhani, E., Naouri, M., Appels, W. M., Wolleben, M., Liu, J., & Shah, S. L. (2023) · SSRN Electronic Journal · doi:10.2139/ssrn.4463409 · Cited by 3
Sequential model-based design of experiments for a heat-integrated biomass downdraft gasifier
Haidar, H. M., Butler, J. W., Gogolek, P. E. G., & McAuley, K. B. (2025) · Bioresource Technology · doi:10.1016/j.biortech.2025.132729 · Cited by 2
Self-citationZhang, X., Lu, J., Tian, Z., Du, W., & Qian, F. (2025) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.5c02032 · Cited by 2
Selection of Parameter Subsets and Design of Experiments for Estimation of Nonlinear Dynamic Systems
Chu, Y., & Hahn, J. (2008) · IFAC Proceedings Volumes · doi:10.3182/20080706-5-kr-1001.00935 · Cited by 2
“…index (Brun et al., 2001), a column pivoting method (Velez-Reyes and Verghese, 1995), an extension of the relative gain array (Sandink et al., 2001), a Gram-Schmidt orthogonalization method (Yao et al., 2003) and a recursive approach based upon principal component analysis (Li et al., 2004).”
MethodMéndez-Blanco, C. S., & Özkan, L. (2024) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.3c03114 · Cited by 2
Moshiritabrizi, I., McMullen, J. P., Wyvratt, B. M., & McAuley, K. B. (2024) · Reaction Chemistry & Engineering · doi:10.1039/d4re00210e · Cited by 2
Self-citationKumar, A., & Sonkar, I. (2025) · Plant and Soil · doi:10.1007/s11104-024-07167-8 · Cited by 2
“The choice of cutoff criteria was somewhat arbitrary (Yao et al. 2003).”
InfluentialGlobal parametric identifiability of mechanistic models in chain polymerization
Rantow, F. S., Soroush, M., & Grady, M. C. (2006) · Proceedings of the ... American Control Conference/Proceedings of the American Control Conference · doi:10.1109/acc.2006.1657188 · Cited by 2
“Recent case studies mostly deal with biological/biochemical systems [15], [16], and a few with catalytic chemical systems [17], [18].”
BackgroundSouflas, I., Pezouvanis, A., & Ebrahimi, K. M. (2015) · Journal of Dynamic Systems Measurement and Control · doi:10.1115/1.4032052 · Cited by 2
Modeling and Analysis Challenges in Systems Biology
Gadkar, K. G., Gunawan, R., & Doyle, F. J. (2004) · IFAC Proceedings Volumes · doi:10.1016/s1474-6670(17)32551-x · Cited by 2
Evans, M. V., Eklund, C. R., Williams, D. N., Sey, Y. M., & Simmons, J. E. (2020) · Inhalation Toxicology · doi:10.1080/08958378.2020.1742818 · Cited by 2
“Sensitivity analysis is one of the tools that can determine if model parameters are identifiable when sensitivity coefficients are not linearly dependent in time (Yao et al. 2003; McLean and McAuley 2012).”
BackgroundDynamic Modelling of a Polypropylene Production Plant
Lesage, F., Nedelec, D., Descales, B., & Stephens, W. D. (2012) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-444-59520-1.50084-1 · Cited by 2
Analysis of the identifiability of the mathematical model of propane pyrolysis
Nurislamova, L. F., & Gubaydullin, I. M. (2021) · Computer Research and Modeling · doi:10.20537/2076-7633-2021-13-5-1045-1057 · Cited by 2
Global estimability analysis and model-based design of experiments in surrogate modeling
Bouchkira, I., Elmisaoui, S., Benjelloun, S., & Latifi, M. A. (2023) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-443-15274-0.50102-5 · Cited by 2
Discrete-Time Model Representations for Biochemical Pathways
He, F., Yeung, L. F., & Brown, M. (2008) · Lecture notes in electrical engineering · doi:10.1007/978-0-387-74935-8_19 · Cited by 2
“Besides, many optimal experimental design methods [10, 19, 38 ] are developed based on maximizing the information of FIM according to commonly used optimal design criteria [2].”
MethodA Two-loop Optimization Strategy for Multi-objective Optimal Experimental Design
Yu, H., Yue, H., & Halling, P. J. (2016) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2016.07.288 · Cited by 2
Игоревна, К. О., & Andornaya, D. V. (2021) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2092/1/012012 · Cited by 5
Run-to-Run Optimization of Biochemical Batch Processes in the Presence of Model-Plant Mismatch
Hille, R. (2018) · UWSpace (University of Waterloo) · Cited by 2
Structural identifiability of large systems biology models
Joubert, D. (2020) · doi:10.18174/507603 · Cited by 2
MIDDoE: An MBDoE Python package for model identification, discrimination, and calibration
Tabrizi, S. Z. B., Barbera, E., da Silva, W. R. L., & Bezzo, F. (2025) · Digital Chemical Engineering · doi:10.1016/j.dche.2025.100276 · Cited by 4
Hamer, C. E., Halbert, B. E., Webster, M., & Scharer, J. M. (2012) · WIT transactions on ecology and the environment · doi:10.2495/wp120141 · Cited by 1
Zaman, M., Maggioni, G. M., & Rajagopalan, A. K. (2025) · Chemical Engineering Science · doi:10.1016/j.ces.2025.123151 · Cited by 2
Cao, X., Chen, X., & Biegler, L. T. (2025) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2025.109296 · Cited by 1
Amaral, G. C., Rios, A. G., Rodrigues, A. E., Ribeiro, A. M., Rodrigues, D., Nogueira, I. B. R., & Ferreira, A. F. P. (2026) · Chemical Engineering Science · doi:10.1016/j.ces.2026.123447 · Cited by 1
Two novel criteria for model-based design of experiments in ill-conditioned systems
Tabrizi, S. Z. B., da Silva, W. R. L., & Bezzo, F. (2026) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2026.109806 · Cited by 1
Critical Issues in the Numerical Treatment of the Parameter Estimation Problems in Immunology
Bocharov, T. L. &. G. (2012) · Journal of Computational Mathematics · doi:10.4208/jcm.1110-m11si12 · Cited by 3
Yoo, S. J., Oh, S.-K., & Lee, J. M. (2012) · IFAC Proceedings Volumes · doi:10.3182/20120710-4-sg-2026.00102 · Cited by 1
Balakrishnan, N. P., Lakshminarayanan, S., & Rangaiah, G. P. (2013) · IFAC Proceedings Volumes · doi:10.3182/20131216-3-in-2044.00061 · Cited by 1
“Details of steps involved in iterative ranking of parameters can be found in Yao et al. (2003).”
BackgroundDesign of Experiments Based on Dynamic Real-time Optimization Approach
Bousbia-Salah, R., Lesage, F., & Latifi, M. A. (2017) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-444-63965-3.50380-9 · Cited by 1
Straznicky, J. I., Aiello, J. P., Gibson, L. A., Jiang, Y., Boller, T., Chiang, H., & McAuley, K. B. (2023) · Macromolecular Theory and Simulations · doi:10.1002/mats.202200073 · Cited by 1
Self-citationDynamic Modeling of Apoptosis and its Interaction with Cell Growth in Mammalian Cell Culture
Meshram, M., Naderi, S., Wei, Y., McConkey, B. J., Ingalls, B., Budman, H. M., & Scharer, J. M. (2011) · IFAC Proceedings Volumes · doi:10.3182/20110828-6-it-1002.02462 · Cited by 1
Set-Membership Parameter Estimation: Improved Understanding of Microgel Polymerization
Jung, F., Caspari, A., Mhamdi, A., & Mitsos, A. (2019) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2019.06.125 · Cited by 1
Santana, V. V., Martins, M. A. F., Rodrigues, A. E., LOUREIRO, J. M., Ribeiro, A. M., & Nogueira, I. B. R. (2021) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.1c00214 · Cited by 1
Mathematical Modeling for the Industrial 2-Mercaptobenzothiazole Batch Production Process
Liang, E., Zhang, S., Liu, B., Qi, B., Nie, Y., & Yuan, Z. (2022) · ACS Omega · doi:10.1021/acsomega.1c06646 · Cited by 1
Development of a Dynamic Model to Describe CHO cells Metabolic Network and Regulation
Ghorbaniaghdam, A. (2013) · PolyPublie (École Polytechnique de Montréal) · Cited by 3
Sepasi, D. (2012) · cIRcle (University of British Columbia) · doi:10.14288/1.0080734 · Cited by 1
“In some applications, parameters with little contribution to the inputoutput behavior can be ignored in the estimation process [64, 116].”
BackgroundZhao, Y. R. (2014) · QSpace (Queen's University Library) · Cited by 1
Polymerization Kinetics of Ethylene/1-Hexene Copolymers Made with Two Metallocene Catalysts
Saadat, S. (2018) · ERA: Education and Research Archive (University of Alberta) · doi:10.7939/r3639km27 · Cited by 1
Leysi-Derilou, Y. (2011) · Corpus Université Laval (Université Laval) · Cited by 1
Optimisation dynamique en temps-réel d’un procédé de polymérisation par greffage
Bousbia-Salah, R. (2018) · doi:10.70675/7d2b62f1zaff8z4f9dzb2b8z18954c7bfad2 · Cited by 1
“7 – Algorithme d’orthogonalisation (Yao et al., 2003)”
Cardenas, C. (2021) · theses.fr (ABES) · doi:10.70675/87178232z2167z400cz9c49z854103ee55f6 · Cited by 8
Optimal input design for sensitivity analysis of microalgal bioreactor systems
Yoo, S. J., Oh, S.-K., & Lee, J. M. (2012) · International Conference on Control, Automation and Systems (ICCAS)
Dynamic Optimization of Integrated Active - Passive Strategies for Building Enthalpy Control
Zhang, R. (2014) · KiltHub Repository · doi:10.1184/r1/6716120
A kinetic model for hydroconversion processing of vacuum residue
Shams, S., McCaffrey, W. C., Gray, M. R., & Ben‐Zvi, A. (2011) · International Symposium on Advanced Control of Industrial Processes
Selection of Simplified Models and Parameter Estimation Using Limited Data
Wu, S.-H. (2009) · QSpace (Queen's University Library)
Karimi, H. (2013) · QSpace (Queen's University Library) · Cited by 2
Golfar, B. (2014) · QSpace (Queen's University Library)
Parameter Estimation of Complex Systems from Sparse and Noisy Data
Chu, Y. (2010) · OakTrust (Texas A&M University Libraries) · Cited by 4
Modeling and identification of a gene regulatory network programming erythropoiesis (1)
Vos, D. D. (2009) · Centrum Wiskunde & Informatica (CWI), the national research institute for mathematics and computer science in the Netherlands
Parameter Identifiability and Estimation in Gene and Protein Interaction Networks
Shelton, R. K. (2008) · VTechWorks (Virginia Tech)
Balakrishnan, N. P., Lakshminarayanan, S., & Rangaiah, G. P. (2021) · National University of Singapore
Gunawan, R., & Bagheri, N. (2018) · MDPI eBooks · doi:10.3390/books978-3-03897-434-5
Applied Control Theory for Biological Processes
Noble, S. L., & Rundell, A. E. (2015) · Springer eBooks · doi:10.1007/978-3-540-70529-1_63
Tio, Z. K., & Balakrishnan, N. P. (2022) · International Symposium on Advanced Control of Industrial Processes · doi:10.1109/adconip55568.2022.9894218
Modelling of water vapor adsorption/desorption on hopcalite in an industrial medical air dryer
Cardenas, C., & Farrusseng, D. (2023) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-443-15274-0.50081-0
An Objective Measure of Distributional Estimability as Applied to the Phase-Type Aging Model
Nie, C., Liu, X., & Provost, S. B. (2024) · Risks · doi:10.3390/risks12020037
Practical Identification of Heat Exchanger Model ParametersPreprint
Tassanbayev, S., Uskenbayeva, G., Shukirova, A., Kulniyazova, K., & Slastenov, I. (2025) · Preprints.org · doi:10.20944/preprints202505.1692.v1
Haidar, H. M., Butler, J. W., Vo, A. D., Gogolek, P. E. G., & McAuley, K. B. (2025) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.5c01138
Self-citationTassanbayev, S., Uskenbayeva, G., Shukirova, A., Kulniyazova, K., & Slastenov, I. (2025) · Processes · doi:10.3390/pr13103289
Carlozo, M. N., Wang, N., Dowling, A. W., & Maginn, E. J. (2026) · Digital Discovery · doi:10.1039/d5dd00537j
A‐optimal model‐based design of experiments for processes with uncertain inputs
Ofori, B., Moshiritabrizi, I., Vo, A. D., & McAuley, K. B. (2026) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.70304
Self-citationIdentification of aerodynamic coefficients from free flight data
Albisser, M. (2015) · doi:10.70675/ab94f713z868bz4379za278z50bc17451ea3
“In practice, a second approach can be used as mentioned in [Yao et al. (2003)], based on a priori knowledge of the system.”
MethodStudy and enhancement of Bayesian calibration applied to building energy models
Akkari, S. (2022) · theses.fr (ABES) · doi:10.70675/f0d96ff9zbffcz469eza5acz7cd9af735d60 · Cited by 1
Modélisation et optimisation des fours de cémentation gazeuse basse pression
Matamoros, F. (2022) · theses.fr (ABES) · doi:10.70675/1f650849zec40z4940zb2e0zc07389e0ce3f
Elmisaoui, S. (2023) · theses.fr (ABES) · doi:10.70675/c723c26ez1959z4caazab3bz027007c890d1 · Cited by 1
A Framework for the Bayesian Calibration of Complex and Data-Scarce Models in Applied Sciences
Schenk, C., & Romero, I. (2026) · Archives of Computational Methods in Engineering · doi:10.1007/s11831-026-10665-w · Cited by 6
“Future work could include an estimability analysis, for example based on orthogonalization [ 65–67 ] or the identifiability approaches discussed in Sect.”
Metadata
- Authors
- Yao, K. Z., Shaw, B. M., Kou, B., McAuley, K. B., & Bacon, D. W.
- Affiliations
- Queen's University (CA)
- a Department of Chemical Engineering , Queen's University , Kingston , Ontario , K7L 3N6 , Canada
- ORCID
- Kou, Bo
- Venue
- Polymer Reaction Engineering
- Publisher
- Informa UK Limited
- Published
- 2003-01-09
- Volume
- 11
- Issue
- 3
- Pages
- 563-588
- ISSN
- 1054-3414 (ISSN-L)
- 1532-2408
- OpenAlex
- W1967988563
- Cited by
- 290
- References
- 34
- Citations by year
- 2026: 5 · 2025: 13 · 2024: 13 · 2023: 23 · 2022: 16 · 2021: 19 · 2020: 21 · 2019: 15 · 2018: 24 · 2017: 9 · 2016: 14 · 2015: 12 · 2014: 14 · 2013: 15 · 2012: 13
- FWCI
- 2.82
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Polymer Reaction Engineering (publishedVersion)
- Funders
- Government of Ontario
- Natural Sciences and Engineering Research Council of Canada
- Topics
- Physical Sciences › Chemistry › Organic Chemistry › Organometallic Complex Synthesis and Catalysis
- Social Sciences › Decision Sciences › Management Science and Operations Research › Optimal Experimental Design Methods
- Physical Sciences › Engineering › Control and Systems Engineering › Control Systems and Identification
- Keywords
- Ziegler-Natta catalysts, parameter estimability, experimental design, rate constants, gas-phase polymerization, polymerization kinetics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.