Modeling ethylene/butene copolymerization with multi-site catalysts: parameter estimability and experimental design
The DOI matches its Crossref record; 33 of the 34 references it cites were found in a registry or an index.
Abstract
Mechanistic models for ethylene copolymerization with Ziegler–Natta catalysts contain many kinetic rate constants. Precise estimates of key parameters are required if the models are to be used to obtain reliable predictions of polymer properties for a specified catalyst over a range of polymerization conditions. In this paper, a novel method is developed to assist modelers in assessing whether their model parameters will be estimable from existing or proposed experimental data, and in determining subsets of influential parameters that can be estimated from the data when the complete set of model parameters cannot be estimated. The effects of using different types of data, varying the number of observations per experimental run, and increasing the number of experimental runs on the number of estimable parameters are considered. A method for comparison of the relative effectiveness of different experimental designs for estimating key parameters in gas‐phase ethylene copolymerization is also presented.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“These methods are appropriate if functional relations h between the parameters emerging from structural non-identifiability are linear.This is often not the case for reaction networks modeled by ODE, because observables depend non-linearly on the parameters.Practical non-identifiability cannot be detected, because a quadratic approximation is not able to explain increasing but limited behavior of”
From Structural and practical identifiability analysis of partially observed dynamical models by exploiting the profile likelihood (2009) · cites this paper as Yao et al., 2003
Citations
Cites
Introduction to Linear Regression Analysis.
Assuncao, R., Sampson, P. D., Montgomery, D. C., & Peck, E. A. (1993) · Journal of the American Statistical Association · doi:10.2307/2290746 · Cited by 5,388
Nonlinear Regression Analysis and Its Applications
Bates, D. M., & Watts, D. G. (1988) · Wiley Series in Probability and Statistics · doi:10.1002/9780470316757 · Cited by 3,979
Nonlinear Parameter Estimation
Chambers, J. M., & Bard, Y. (1975) · Technometrics · doi:10.2307/1268363 · Cited by 2,158
Nonlinear Parameter Estimation
Brubaker, T. A., & O'Keefe, K. R. (1979) · Analytical Chemistry · doi:10.1021/ac50049a796 · Cited by 2,134
Parameter Estimation in Engineering and Science
de Oliveira, J. T., Beck, J. V., & Arnold, K. J. (1979) · International Statistical Review / Revue Internationale de Statistique · doi:10.2307/1403212 · Cited by 1,480 · cited 3×
“6 is equivalent to scaling by the standard deviations (Beck and Arnold, 1977).”
BackgroundInfluentialIntroduction to Linear Regression Analysis
Gray, J. B. (2002) · Technometrics · doi:10.1198/tech.2002.s714 · Cited by 943
DESIGN OF EXPERIMENTS IN NON-LINEAR SITUATIONS
BOX, G. E. P., & LUCAS, H. L. (1959) · Biometrika · doi:10.1093/biomet/46.1-2.77 · Cited by 738 · cited 2×
“The widely used D-optimality design criterion (Box and Lucas, 1959), which directly minimizes the size of the JCR, can be written as:”
MethodParameter Estimation in Engineering and Science.
Folks, J. L., Beck, J. V., & Arnold, K. J. (1978) · Journal of the Royal Statistical Society. Series A (General) · doi:10.2307/2344460 · Cited by 610
The Bayesian estimation of common parameters from several responses
BOX, G. E. P., & DRAPER, N. R. (1965) · Biometrika · doi:10.1093/biomet/52.3-4.355 · Cited by 304
Identifiability of State Space Models
Walter, E. (1982) · Lecture Notes in Biomathematics · doi:10.1007/978-3-642-61823-9 · Cited by 278 · cited 1×
“Estimability is closely linked with sensitivity analysis (Walter, 1982).”
Background
Research works printed but not linked: 9
- Haskins G. D., 1999, M.Sc. thesis
- Klaus R. A., 1981, Ph. D. thesis
- Kou B., 2003, Ph.D. thesis
- Pigeon M. G., 1996, PhD thesis
- Seber G. A.F., 1989, Nonlinear Regression, Wiley Series in Probability and Mathematical Statistics: Probability and Mathematical Statistics
- Shaw B. M., 1999, Ph.D. thesis
- Soares J. B.P., 1995, Polym. React. Eng., 3, 261
- Stewart W. E., 1995, GREG: A Fortran Subroutine for Nonlinear Regression and Experimental Design, User's Manual
- Williams C. H., 1996, Master's thesis
Cited by
Items 101–200 of 289
Chen, X., Shao, Z., Gu, X., Feng, L., & Biegler, L. T. (2018) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.8b04424 · Cited by 17
Pant, S. (2018) · Journal of The Royal Society Interface · doi:10.1098/rsif.2017.0871 · Cited by 24
“Lastly, parameter identifiability based on sensitivity analysis also assesses correlation/dependence between the parameters—through principle component analysis [2], correlation method [3], orthogonal method [4], and the eigenvalue method [5]—to identify which pairs of parameters, owing to the high correlation, are li…”
MethodPhotocuring of di-acrylate in presence of oxygen
Iedema, P. D., Schamboeck, V., Boonen, H., van der Linden, M. N., & Willemse, R. X. E. (2019) · Chemical Engineering Science · doi:10.1016/j.ces.2019.05.056 · Cited by 17
Goshtasbi, A., Chen, J., Waldecker, J. R., Hirano, S., & Ersal, T. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ab7092 · Cited by 24
Galbusera, L., Azzini, I., Jonkeren, O., & Giannopoulos, G. (2016) · ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems Part A Civil Engineering · doi:10.1061/ajrua6.0000861 · Cited by 16
A Multi-Model Approach to Identification of Biosynthetic Pathways
Dunlop, M. J., Franco, E., & Murray, R. M. (2007) · Proceedings of the ... American Control Conference/Proceedings of the American Control Conference · doi:10.1109/acc.2007.4282720 · Cited by 17
“An iterative scheme to optimi ze identifiability of biochemical networks is offered in [11], which is an extension of a method introduced in [27].”
MethodParameter subset selection and biased estimation for a class of ill-conditioned estimation problems
Kim, B., & Lee, J. H. (2019) · Journal of Process Control · doi:10.1016/j.jprocont.2019.05.015 · Cited by 16
Receding horizon experiment design with application in SOFC parameter estimation
Jayasankar, B. R., Huang, B., & Ben‐Zvi, A. (2010) · IFAC Proceedings Volumes · doi:10.3182/20100705-3-be-2011.00090 · Cited by 16
“The sensitivity matrix based on derivative of dynamic response trajectory with respect to parameters has been given in Yao et al. (2003) .”
MethodBrandão, A. L. T., Alberton, A. L., Pinto, J. C., & Soares, J. B. P. (2016) · Macromolecular Theory and Simulations · doi:10.1002/mats.201600059 · Cited by 16
Identifiability study of a liquid–liquid phase‐transfer catalyzed reaction system
Ben‐Zvi, A., McAuley, K. B., & McLellan, P. J. (2004) · AIChE Journal · doi:10.1002/aic.10202 · Cited by 16
Self-citationParameter estimation with improved model prediction for over-parametrized nonlinear systems
Chen, W., Wang, B., & Biegler, L. T. (2021) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2021.107601 · Cited by 17
Sensitivity Analysis and Practical Identifiability of Some Mathematical Models in Biology
Игоревна, К. О., Andornaya, D. V., & Kabanikhin, S. I. (2020) · Journal of Applied and Industrial Mathematics · doi:10.1134/s1990478920010123 · Cited by 17
Population‐based modeling of the progression of apoptosis in mammalian cell culture
Meshram, M., Naderi, S., McConkey, B. J., Budman, H. M., Scharer, J. M., & Ingalls, B. (2011) · Biotechnology and Bioengineering · doi:10.1002/bit.24392 · Cited by 15
“We employed an identifiability analysis via the orthogonalization method (Yao et al., 2003) and used the Fisher information matrix (FIM) to calculate confidence intervals for the identifiable model parameters.”
MethodBedel, S., Vallières, C., & Latifi, M. A. (2017) · Adsorption · doi:10.1007/s10450-017-9864-7 · Cited by 15
“The set of the most estimable parameters was determined by applying the following algorithm, which consists of eight steps (Yao et al. 2003): Step 1: Compute the magnitude, that is, the square root”
BackgroundMethodInfluentialPredictive Modeling of a Batch Filter Mating Process
Malwade, A., Nguyen, A., Sadat-Mousavi, P., & Ingalls, B. (2017) · Frontiers in Microbiology · doi:10.3389/fmicb.2017.00461 · Cited by 16
“To account for correlation among the parameters, the orthogonalization approach of Yao et al. (2003) was applied Frontiers in Microbiology | www.frontiersin.org 4 March 2017 | Volume 8 | Article 461 to arrive at practical measures of identifiability, as follows.”
MethodInfluentialModelling of heat transfer and pyrolysis reactions in an industrial ethylene cracking furnace
Karimi, H., Cowperthwaite, E. V., Olayiwola, B. O., Farag, H., & McAuley, K. B. (2017) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.22844 · Cited by 15
Self-citationChaffart, D., & Ricardez‐Sandoval, L. (2017) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.22912 · Cited by 16
Saadat, S., Soares, J. B. P., DesLauriers, P. J., & Fodor, J. S. (2019) · Macromolecular Reaction Engineering · doi:10.1002/mren.201900032 · Cited by 15
Wu, W.-L., Chappelow, C., Hanspal, N. S., Larsen, P. A., Patton, J. T., Shinkle, A. A., & Nagy, Z. K. (2024) · Organic Process Research & Development · doi:10.1021/acs.oprd.3c00373 · Cited by 14
Modeling the coupled extracellular and intracellular environments in mammalian cell culture
Meshram, M., Naderi, S., McConkey, B. J., Ingalls, B., Scharer, J. M., & Budman, H. M. (2013) · Metabolic Engineering · doi:10.1016/j.ymben.2013.06.002 · Cited by 18
“Instead, the estimability analysis of Yao et al. (2003) addresses the correlation issue by extracting the effect of a group of parameter on the sensitivity matrix and then addressing the effect of the remaining parameters.”
BackgroundMethodOptimal Experimental Design for an Enzymatic Biodiesel Production System
Yu, H., Yue, H., & Halling, P. J. (2015) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2015.09.141 · Cited by 17
“In this work, based on the LSA results, the orthogonalization-based method (Yao et al., 2003) is applied to examine parameter correlations and to rank parameters so as to select the set of identifiable parameters.”
MethodYu, H., Yue, H., & Halling, P. J. (2018) · Chemical Engineering Science · doi:10.1016/j.ces.2018.05.047 · Cited by 13
Assessment of the parameter identifiability of population balance models for air jet mills
Bhonsale, S. S., Stokbroekx, B., & van Impe, J. F. M. (2020) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2020.107056 · Cited by 14
Eghtesadi, Z., & McAuley, K. B. (2015) · AIChE Journal · doi:10.1002/aic.15096 · Cited by 15
Self-citationEghtesadi, Z., Wu, S., & McAuley, K. B. (2012) · Industrial & Engineering Chemistry Research · doi:10.1021/ie302408b · Cited by 16
Self-citationChen, K., Liu, B., & Soares, J. B. P. (2016) · Macromolecular Reaction Engineering · doi:10.1002/mren.201500066 · Cited by 14
Pladis, P., Baltsas, A., Meimaroglou, D., & Kiparissides, C. A. (2018) · Macromolecular Reaction Engineering · doi:10.1002/mren.201800017 · Cited by 14
Nogueira, I. B. R., Ribeiro, A. M., Rodrigues, A. E., & LOUREIRO, J. M. (2015) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2015.12.009 · Cited by 16
Model‐based design of experiments for polyether production from bio‐based 1,3‐propanediol
Vo, A. D., Shahmohammadi, A., & McAuley, K. B. (2021) · AIChE Journal · doi:10.1002/aic.17394 · Cited by 14
Self-citationDistributed simultaneous state and parameter estimation of nonlinear systems
Liu, S., Yin, X., Liu, J., Liu, J., & Ding, F. (2022) · Chemical Engineering Research and Design · doi:10.1016/j.cherd.2022.02.027 · Cited by 13
Bouchkira, I., Benjelloun, S., Khamar, L., & Latifi, M. A. (2022) · Fluid Phase Equilibria · doi:10.1016/j.fluid.2022.113594 · Cited by 15
Elmisaoui, S., Latifi, M. A., & Khamar, L. (2023) · Hydrometallurgy · doi:10.1016/j.hydromet.2023.106197 · Cited by 13
Baker, S. M., Poskar, C. H., & Junker, B. H. (2011) · EURASIP Journal on Bioinformatics and Systems Biology · doi:10.1186/1687-4153-2011-7 · Cited by 18
Multirate moving horizon estimation combined with parameter subset selection
Bae, J., Kim, Y., & Lee, J. M. (2021) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2021.107253 · Cited by 13
Acilan, E., & Göl, M. (2021) · IEEE Transactions on Power Systems · doi:10.1109/tpwrs.2021.3130076 · Cited by 13
“In [24], the authors proposed to rank the columns of sensitivity matrix corresponding to the parameters using an orthogonal-projection based method.”
MethodYuan, X., Nagy, Z. K., & Benyahia, B. (2025) · Chemical Engineering Journal Advances · doi:10.1016/j.ceja.2025.100823 · Cited by 13
Mathematical Modeling of Polyether Production from 1,3‐Propanediol: Accounting for Linear Oligomers
Cui, W. J., McAuley, K. B., Spence, R. E. V. H., & Xie, T. (2015) · Macromolecular Reaction Engineering · doi:10.1002/mren.201400038 · Cited by 12
Self-citationAhmadjo, S., Arabi, H., Nekoomanesh, M., Mortazavi, S. M. M., Zohuri, G., Ahmadi, M., & Bolandi, S. (2011) · Chemical Engineering & Technology · doi:10.1002/ceat.201000272 · Cited by 12
Accelerating the parameters identifiability procedure: Set by set selection
Alberton, K. P. F., Alberton, A. L., Maggio, J. D., Díaz, M. S., & Secchi, A. R. (2013) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2013.04.014 · Cited by 12
Modeling of a batch emulsion copolymerization reactor in the presence of a chain transfer agent
Benyahia, B., Latifi, M. A., Fonteix, C., & Pla, F. (2011) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-444-53711-9.50026-2 · Cited by 12
Sequential Parameter Estimation for Mammalian Cell Model Based on In Silico Design of Experiments
Wang, Z., Sheikh, H., Lee, K., & Georgakis, C. (2018) · Processes · doi:10.3390/pr6080100 · Cited by 12
Reduced Hessian based parameter selection and estimation with simultaneous collocation approach
Chen, W., & Biegler, L. T. (2020) · AIChE Journal · doi:10.1002/aic.16242 · Cited by 12
Parameter estimation and estimability analysis in pharmaceutical models with uncertain inputs
Moshiritabrizi, I., Abdi, K., McMullen, J. P., Wyvratt, B. M., & McAuley, K. B. (2023) · AIChE Journal · doi:10.1002/aic.18168 · Cited by 11
Self-citationAtarianshandiz, M., McAuley, K. B., & Shahsavand, A. (2023) · Processes · doi:10.3390/pr11102838 · Cited by 11
Self-citationAiello, J. P., Jiang, Y., Moebus, J. A., Greenhalgh, B. R., & McAuley, K. B. (2021) · Macromolecular Theory and Simulations · doi:10.1002/mats.202000079 · Cited by 11
Self-citationTuveri, A., Nakama, C. S. M., Matias, J., Holck, H. E., Jäschke, J., Imsland, L., & Bar, N. (2023) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2023.108183 · Cited by 16
Kinetic parameter estimation based on spectroscopic data with unknown absorbing species
Chen, W., Biegler, L. T., & García‐Muñoz, S. (2018) · AIChE Journal · doi:10.1002/aic.16334 · Cited by 11
Mathematical Models of Protease-Based Enzymatic Biosensors
Agrawal, D. K., Dolan, E. M., Hernandez, N. E., Blacklock, K. M., Khare, S. D., & Sontag, E. D. (2020) · ACS Synthetic Biology · doi:10.1021/acssynbio.9b00279 · Cited by 11
An Improved PO3G Model–Accounting for Cyclic Oligomers
Vo, A. D., Cui, W. J., & McAuley, K. B. (2020) · Macromolecular Theory and Simulations · doi:10.1002/mats.202000023 · Cited by 11
Self-citationJoubert, D., Stigter, J. D., & Molenaar, J. (2021) · Scientific Reports · doi:10.1038/s41598-021-96293-9 · Cited by 13
Robust Batch-to-Batch Optimization with Scenario Adaptation
Kim, B., Huusom, J. K., & Lee, J. H. (2019) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.8b06233 · Cited by 11
Dynamical modelling of street protests using the Yellow Vest Movement and Khabarovsk as case studies
Alsulami, A., Glukhov, A., Shishlenin, M. A., & Petrovskii, S. (2022) · Scientific Reports · doi:10.1038/s41598-022-23917-z · Cited by 11
Effect of mercury in the influx and efflux of nutrients in the microalga Desmodesmus armatus
Quevedo-Ospina, C., Arroyave, C., Peñuela, M., & Quiceno, A. P. V. (2023) · Aquatic Toxicology · doi:10.1016/j.aquatox.2023.106496 · Cited by 12
Moeini, N., Teimoury, H., Salimi, M., Bahri‐Laleh, N., Joshaghani, M., Duran, J., Poater, A., & Posada‐Pérez, S. (2023) · Polymer · doi:10.1016/j.polymer.2023.126640 · Cited by 10
Modeling of Polyolefin Polymerization in Semibatch Slurry Reactors: Experiments and Simulations
Casalini, T., Visscher, F., Janssen, E., Bertola, F., Storti, G., & Morbidelli, M. (2016) · Macromolecular Reaction Engineering · doi:10.1002/mren.201600036 · Cited by 10
Schenk, C., Short, M., Rodriguez, J. S., Thierry, D. M., Biegler, L. T., García‐Muñoz, S., & Chen, W. (2020) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2019.106716 · Cited by 10
Ben‐Zvi, A. (2008) · AIChE Journal · doi:10.1002/aic.11465 · Cited by 11
Gibson, L. A., Liu, F. F., Harris, T. J., & McAuley, K. B. (2024) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.3c04058 · Cited by 9
Self-citationBinns, M., Usai, A., & Theodoropoulos, C. (2024) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2024.108683 · Cited by 9
Optimal experimental design for optimal process design: A trilevel optimization formulation
Walz, O., Djelassi, H., & Mitsos, A. (2019) · AIChE Journal · doi:10.1002/aic.16788 · Cited by 9
Simultaneous Parameters Identifiability and Estimation of anE. coliMetabolic Network Model
Alberton, K. P. F., Alberton, A. L., Maggio, J. D., Estrada, V., Díaz, M. S., & Secchi, A. R. (2015) · BioMed Research International · doi:10.1155/2015/454765 · Cited by 12
“[25], the most identifiable parameter is the one with the highest Euclidian norm of the sensitivity vector, that is, max j ‖b θj ‖.”
BackgroundMethodInfluentialPietrafesa, T. R., Brandolin, A., Sarmoria, C., & Asteasuain, M. (2023) · Macromolecular Theory and Simulations · doi:10.1002/mats.202300018 · Cited by 8
Kozachynskyi, V., Hoffmann, C., & Esche, E. (2024) · Chemical Engineering Science · doi:10.1016/j.ces.2024.121122 · Cited by 9
Feng, H.-H., Yang, G., Wang, H., Gu, X., Feng, L., Zhang, C., Chen, X., Wang, D.-F., & Gao, Y. (2023) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.2c03786 · Cited by 8
Ngo, V. V., Latifi, M. A., & Simonnot, M. (2013) · Journal of Hydrologic Engineering · doi:10.1061/(asce)he.1943-5584.0000953 · Cited by 8
Kinetic modeling of Moorella thermoacetica growth on single and dual-substrate systems
Schmitt, E., Bura, R., Gustafson, R., & Ehsanipour, M. (2016) · Bioprocess and Biosystems Engineering · doi:10.1007/s00449-016-1631-8 · Cited by 8
Discrete-Time Model Representation for Biochemical Pathway Systems
He, F., Yeung, L. F., & Brown, M. (2007) · Cited by 9
Dynamic response to process disturbances—A comparison between TMB/SMB models in transient regime
Nogueira, I. B. R., Ribeiro, A. M., Rodrigues, A. E., & LOUREIRO, J. M. (2017) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2017.01.026 · Cited by 8
Bae, J., Jeong, D. H., & Lee, J. M. (2020) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.0c04219 · Cited by 8
Cardenas, C., Latifi, M. A., Vallières, C., & Marsteau, S. (2023) · Separation and Purification Technology · doi:10.1016/j.seppur.2023.124173 · Cited by 8
Parallel models for arborescent polyisobutylene synthesized in batch reactor
Zhao, Y. R., McAuley, K. B., & Puskas, J. E. (2014) · AIChE Journal · doi:10.1002/aic.14655 · Cited by 8
Self-citationCasas‐Orozco, D., Villa, A. L., Guerra, O. J., & Reklaitis, G. V. (2018) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2018.04.002 · Cited by 8
Straznicky, J. I., Gibson, L. A., Celse, B., & McAuley, K. B. (2025) · Chemical Engineering Research and Design · doi:10.1016/j.cherd.2025.02.037 · Cited by 8
Self-citationClustering of Redundant Parameters for Fault Isolation with Gaussian Residuals
Mendler, A., Döhler, M., Ventura, C. E., & Mevel, L. (2020) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2020.12.877 · Cited by 7
Kusumo, K. P., Kuriyan, K., Vaidyaraman, S., García‐Muñoz, S., Shah, N., & Chachuat, B. (2022) · Reaction Chemistry & Engineering · doi:10.1039/d1re00465d · Cited by 7
An Improved Model for Polyether Production from 1,3‐Propanediol
Vo, A. D., Elraghy, A., Spence, R. E. V. H., & McAuley, K. B. (2020) · Macromolecular Reaction Engineering · doi:10.1002/mren.201900045 · Cited by 7
Self-citationImproved Kinetic Rate Constants for Nylon 6, Nylon 6,6, and Nylon 6/6,6 Copolymer
Liu, F. F., & McAuley, K. B. (2019) · Macromolecular Reaction Engineering · doi:10.1002/mren.201900037 · Cited by 7
Self-citationDetermination of critical network interactions: an augmented Boolean pseudo-dynamics approach
Soni, A. S., Jenkins, J. W., & Sundaram, S. (2008) · IET Systems Biology · doi:10.1049/iet-syb:20070025 · Cited by 7
Localizability of damage with statistical tests and sensitivity-based parameter clusters
Mendler, A., Döhler, M., Ventura, C. E., & Mevel, L. (2023) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2023.110783 · Cited by 8
KIPET – An Open-Source Kinetic Parameter Estimation Toolkit
Short, M., Schenk, C., Thierry, D. M., Rodriguez, J. S., Biegler, L. T., & García‐Muñoz, S. (2019) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-12-818597-1.50047-3 · Cited by 6
A dynamic model of tablet film coating processes for control system design
Rodrigues, C. P., Duchesne, C., Poulin, É., & Lapointe-Garant, P.-P. (2023) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2023.108251 · Cited by 6
Nassiri, H., Arabi, H., & Hakim, S. (2011) · Reaction Kinetics Mechanisms and Catalysis · doi:10.1007/s11144-011-0391-3 · Cited by 6
Ngo, V. V., Gerke, H. H., & Badorreck, A. (2014) · Transport in Porous Media · doi:10.1007/s11242-014-0315-6 · Cited by 6
Haidar, H. M., Butler, J. W., Lotfi, S., Vo, A. D., Gogolek, P. E. G., & McAuley, K. B. (2024) · Energy Conversion and Management · doi:10.1016/j.enconman.2024.119372 · Cited by 5
Self-citationAnalyzing the Effects of Irrigation on the Sensitivity and Estimability of Soil Hydraulic Parameters
Agarwal, P., & Sharma, P. K. (2022) · Journal of Irrigation and Drainage Engineering · doi:10.1061/(asce)ir.1943-4774.0001691 · Cited by 5
Campbell, T. J. S., Rielly, C. D., & Benyahia, B. (2024) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-443-28824-1.50058-2 · Cited by 5
Parameter Estimation in a PO3G Model with Temperature Effects
Vo, A. D., Spence, R. E. V. H., & McAuley, K. B. (2020) · Macromolecular Theory and Simulations · doi:10.1002/mats.202000061 · Cited by 5
Self-citationDiagnosing Parameter Estimability Problems in Polymerization Models
Liu, F. F., Vo, A. D., & McAuley, K. B. (2021) · Macromolecular Theory and Simulations · doi:10.1002/mats.202100045 · Cited by 5
Self-citationOrthogonalization-Based Gain Conditioning for Linear Model Predictive Control
Sanborn, S. D., Varshney, D., & McAuley, K. B. (2023) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.2c02700 · Cited by 5
Self-citationAnalysis of an Industrial Adsorption Process based on Ammonia Chemisorption: Modeling and Simulation
Cardenas, C., Marsteau, S., Sigot, L., Vallières, C., & Latifi, M. A. (2020) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-12-823377-1.50105-1 · Cited by 5
A model for the devolatilization of EPDM rubber in a series of steam stripping vessels
Francoeur, A. J. B., Karimi, H., McAuley, K. B., & D’Agnillo, L. (2014) · AIChE Journal · doi:10.1002/aic.14448 · Cited by 5
Self-citationDesign of a genetic layered feedback controller in synthetic biological circuitryPreprint
Hu, C. Y., & Murray, R. M. (2019) · bioRxiv (Cold Spring Harbor Laboratory) · doi:10.1101/647057 · Cited by 6
“Next we performed parameter sensitivity analysis [10, 11, 12] of the two types of layered feedback controllers in their transient states—with sRNA regulators and protein regulators.”
MethodESTAN—A toolbox for standardized and effective global sensitivity-based estimability analysis
Bouchkira, I., Latifi, M. A., & Benyahia, B. (2024) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2024.108690 · Cited by 4
Tang, R., Liang, D., Wang, Y., Su, Y., Zhou, Y., Luo, Z., & Xie, L. (2024) · Chemical Engineering Science · doi:10.1016/j.ces.2024.121047 · Cited by 4
Understanding street protests: from a mathematical model to protest management
Petrovskii, S., Shishlenin, M. A., & Glukhov, A. (2025) · PLoS ONE · doi:10.1371/journal.pone.0319837 · Cited by 9
“In order to investigate the parameters’ identifiability, we apply the orthogonal method [46].”
Yoo, S. J., Oh, S.-K., & Lee, J. M. (2013) · Korean Chemical Engineering Research · doi:10.9713/kcer.2013.51.1.87 · Cited by 4
“Generally, not all parameters have a significant effect on the model predictions[Yao et al., 2003].”
BackgroundMethodHille, R., & Budman, H. M. (2016) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2016.07.217 · Cited by 4
Near‐optimal time series sampling based on the reduced Hessian
Chen, W., & Biegler, L. T. (2020) · AIChE Journal · doi:10.1002/aic.16248 · Cited by 4
Gibson, L. A., Jiang, Y., Boller, T., Chiang, H., & McAuley, K. B. (2023) · Macromolecular Reaction Engineering · doi:10.1002/mren.202200067 · Cited by 4
Self-citationYuan, X., & Benyahia, B. (2023) · Computer-aided chemical engineering/Computer aided chemical engineering · doi:10.1016/b978-0-443-15274-0.50041-x · Cited by 5
Metadata
- Authors
- Yao, K. Z., Shaw, B. M., Kou, B., McAuley, K. B., & Bacon, D. W.
- Affiliations
- Queen's University (CA)
- a Department of Chemical Engineering , Queen's University , Kingston , Ontario , K7L 3N6 , Canada
- ORCID
- Kou, Bo
- Venue
- Polymer Reaction Engineering
- Publisher
- Informa UK Limited
- Published
- 2003-01-09
- Volume
- 11
- Issue
- 3
- Pages
- 563-588
- ISSN
- 1054-3414 (ISSN-L)
- 1532-2408
- OpenAlex
- W1967988563
- Cited by
- 290
- References
- 34
- Citations by year
- 2026: 5 · 2025: 13 · 2024: 13 · 2023: 23 · 2022: 16 · 2021: 19 · 2020: 21 · 2019: 15 · 2018: 24 · 2017: 9 · 2016: 14 · 2015: 12 · 2014: 14 · 2013: 15 · 2012: 13
- FWCI
- 2.82
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Polymer Reaction Engineering (publishedVersion)
- Funders
- Government of Ontario
- Natural Sciences and Engineering Research Council of Canada
- Topics
- Physical Sciences › Chemistry › Organic Chemistry › Organometallic Complex Synthesis and Catalysis
- Social Sciences › Decision Sciences › Management Science and Operations Research › Optimal Experimental Design Methods
- Physical Sciences › Engineering › Control and Systems Engineering › Control Systems and Identification
- Keywords
- Ziegler-Natta catalysts, parameter estimability, experimental design, rate constants, gas-phase polymerization, polymerization kinetics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.