The DOI matches its Crossref record.
Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect
Open accessAbstract
Three-dimensional (3D) printing bioactive ceramics have demonstrated alternative approaches to bone tissue repair, but an optimized materials system for improving the recruitment of host osteogenic cells into the bone defect and enhancing targeted repair of the thin-wall craniomaxillofacial defects remains elusive. Herein we systematically evaluated the role of side-wall pore architecture in the direct-ink-writing bioceramic scaffolds on mechanical properties and osteogenic capacity in rabbit calvarial defects. The pure calcium silicate (CSi) and dilute Mg-doped CSi (CSi-Mg6) scaffolds with different layer thickness and macropore sizes were prepared by varying the layer deposition mode from single-layer printing (SLP) to double-layer printing (DLP) and then by undergoing one-, or two-step sintering. It was found that the dilute Mg doping and/or two-step sintering schedule was especially beneficial for improving the compressive strength (∼25-104 MPa) and flexural strength (∼6-18 MPa) of the Ca-silicate scaffolds. The histological analysis for the calvarial bone specimens in vivo revealed that the SLP scaffolds had a high osteoconduction at the early stage (4 weeks) but the DLP scaffolds displayed a higher osteogenic capacity for a long time stage (8-12 weeks). Although the DLP CSi scaffolds displayed somewhat higher osteogenic capacity at 8 and 12 weeks, the DLP CSi-Mg6 scaffolds with excellent fracture resistance also showed appreciable new bone tissue ingrowth. These findings demonstrate that the side-wall pore architecture in 3D printed bioceramic scaffolds is required to optimize for bone repair in calvarial bone defects, and especially the Mg doping wollastontie is promising for 3D printing thin-wall porous scaffolds for craniomaxillofacial bone defect treatment.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Three-dimensional (3D) printed scaffold and material selection for bone repair
Zhang, L., Yang, G., Johnson, B. N., & Jia, X. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2018.11.039 · Cited by 865
Self-citationDigital light processing 3D printed silk fibroin hydrogel for cartilage tissue engineering
Hong, H., Seo, Y. B., Kim, D. Y., Lee, J. S., Lee, Y. J., Lee, H., Ajiteru, O., Sultan, M. T., Lee, O. J., Kim, S. H., et al. (2020) · Biomaterials · doi:10.1016/j.biomaterials.2019.119679 · Cited by 473
Rheological characterisation of ceramic inks for 3D direct ink writing: A review
del-Mazo-Barbara, L., & Ginebra, M.-P. (2021) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2021.08.031 · Cited by 444
Current Biomedical Applications of 3D Printing and Additive Manufacturing
Ahangar, P., Cooke, M. E., Weber, M. H., & Rosenzweig, D. H. (2019) · Applied Sciences · doi:10.3390/app9081713 · Cited by 309
Zhang, B., Pei, X., Zhou, C., Fan, Y., Jiang, Q., Ronca, A., D'Amora, U., Chen, Y., Li, H., Sun, Y., et al. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.04.065 · Cited by 305
Metadata
- Authors
- Shao, H., Ke, X., Liu, A., Sun, M., He, Y., Yang, X., Fu, J., Liu, Y., Zhang, L., Yang, G., Xu, S., & Gou, Z.
- Venue
- Biofabrication
- Publisher
- IOP Publishing
- Published
- 2017-04-12
- Volume
- 9
- Issue
- 2
- Pages
- 025003
- ISSN
- 1758-5082 (ISSN-L)
- 1758-5090
- OpenAlex
- W2595489832
- Cited by
- 172
- References
- 0
- FWCI
- 8.61
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect. https://app.cochat.ai/papers/10.1088/1758-5090/aa663c
- The paper
- Shao, H., Ke, X., Liu, A., Sun, M., He, Y., Yang, X., Fu, J., Liu, Y., Zhang, L., Yang, G., Xu, S., & Gou, Z. (2017). Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect. Biofabrication. https://doi.org/10.1088/1758-5090/aa663c
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.