The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Effects of Humidity and Solution Viscosity on Electrospun Fiber Morphology
Open accessAbstract
Electrospinning is a popular technique to fabricate tissue engineering scaffolds due to the exceptional tunability of fiber morphology that can be used to control scaffold mechanical properties, degradation rate, and cell behavior. Although the effects of modulating processing or solution parameters on fiber morphology have been extensively studied, there remains limited understanding of the impact of environmental parameters such as humidity. To address this gap, three polymers (poly(ethylene glycol) [PEG], polycaprolactone [PCL], and poly(carbonate urethane) [PCU]) were electrospun at a range of relative humidities (RH = 5%-75%) and the resulting fiber architecture characterized with scanning electron microscopy. Low relative humidity (< 50%) resulted in fiber breakage for all three polymers due to decreased electrostatic discharge from the jet. At high relative humidity (> 50%), three distinct effects were observed based on individual polymer properties. An increase in fiber breakage and loss of fiber morphology occurred in the PEG system as a result of increased water absorption at high relative humidity. In contrast, surface pores on PCL fibers were observed and hypothesized to have formed via vapor-induced phase separation. Finally, decreased PCU fiber collection occurred at high humidity likely due to increased electrostatic discharge. These findings highlight that the effects of relative humidity on electrospun fiber morphology are dependent on polymer hydrophobicity, solvent miscibility with water, and solvent volatility. An additional study was conducted to highlight that small changes in molecular weight can strongly influence solution viscosity and resulting fiber morphology. We propose that solution viscosity rather than concentration is a more useful parameter to report in electrospinning methodology to enable reproduction of findings. In summary, this study further elucidates key mechanisms in electrospun fiber formation that can be utilized to fabricate tissue engineering scaffolds with tunable and reproducible properties.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Keun Kwon, I., Kidoaki, S., & Matsuda, T. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2004.10.007 · Cited by 607
Cited by
Electrospinning: Processes, Structures, and Materials
Ahmadi Bonakdar, M., & Rodrigue, D. (2024) · Macromol · doi:10.3390/macromol4010004 · Cited by 380
Coaxial Electrospinning Formation of Complex Polymer Fibers and their Applications
Han, D., & Steckl, A. J. (2019) · ChemPlusChem · doi:10.1002/cplu.201900281 · Cited by 355
Fabrication of Electrospun Polymer Nanofibers with Diverse Morphologies
Wang, C., Wang, J., Zeng, L., Qiao, Z., Liu, X., Liu, H., Zhang, J., & Ding, J. (2019) · Molecules · doi:10.3390/molecules24050834 · Cited by 331
Porous electrospun polycaprolactone (PCL) fibres by phase separation
Katsogiannis, K. A. G., Vladisavljević, G. T., & Georgiadou, S. (2015) · European Polymer Journal · doi:10.1016/j.eurpolymj.2015.01.028 · Cited by 266
Development of Filter Media by Electrospinning for Air Filtration of Nanoparticles from PET Bottles
Bonfim, D. P. F., Cruz, F. G. S., Guerra, V. G., & Aguiar, M. L. (2021) · Membranes · doi:10.3390/membranes11040293 · Cited by 60
Metadata
- Authors
- Nezarati, R. M., Eifert, M. B., & Cosgriff-Hernandez, E.
- Venue
- Tissue Engineering Part C: Methods
- Publisher
- SAGE Publications
- Published
- 2013-10
- Volume
- 19
- Issue
- 10
- Pages
- 810-819
- ISSN
- 1937-3384 (ISSN-L)
- 1937-3392
- OpenAlex
- W1995707214
- Cited by
- 459
- References
- 1
- FWCI
- 4.43
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effects of Humidity and Solution Viscosity on Electrospun Fiber Morphology. https://app.cochat.ai/papers/10.1089/ten.tec.2012.0671
- The paper
- Nezarati, R. M., Eifert, M. B., & Cosgriff-Hernandez, E. (2013). Effects of Humidity and Solution Viscosity on Electrospun Fiber Morphology. Tissue Engineering Part C: Methods. https://doi.org/10.1089/ten.tec.2012.0671
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.