The DOI matches its Crossref record.
The lubrication of rollers
Abstract
When lubricated rollers are run together they are separated by a hydrodynamically formed oil film. The thickness of this film has been measured by a capacitance method up to loads of 1000 Lb. per inch of face (1.76 x 103 dyn cm -1) for conditions of pure rolling and for conditions of rolling with sliding such as exist at the contacts of gear teeth. It has been found, at low loads, that the film thickness varies inversely with load and proportionately with speed, as simple hydrodynamic theory suggests, but that the actual thickness is approximately one-half of the theoretical thickness. At higher loads, of greater practical importance, the film thickness is shown to be of the order 1u (-4x10-5 in) which is greater than that predicted by simple theory. Experimental evidence is presented that this failure of the simple theory is due to the increased viscosity of the oil under pressure and to the deformation of the surfaces by the load. The film thickness, at practical loads, has been found to vary little with load, less than proportionately with speed but to vary greatly with the temperatures of the surfaces. Estimates of the temperature reached by the oil in its passage through the conjunction of the surfaces have been made from measurements of the electrical resistivity of the oil. This temperature, which depends upon load and the peripheral speeds and which may exceed 250° C, appears to have little influence upon the film thickness. From this it is argued that the film thickness is largely determined by the conditions, on the entry side of the conjunction, ahead of the region in which the viscous losses and heating of the oil become intense.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
The temperature of rubbing surfaces
Archard, J. F. (1959) · Wear · doi:10.1016/0043-1648(59)90159-0 · Cited by 1,062
Elasto-hydrodynamic lubrication: A survey of isothermal solutions
Dowson, D., Higginson, G. R., & Whitaker, A. V. (1962) · Journal of Mechanical Engineering Science · doi:10.1243/jmes_jour_1962_004_018_02 · Cited by 157
A Friction Model of Partial-EHL Contacts and its Application to Power Loss in Spur Gears
Wu, S., & Cheng, H. S. (1991) · Tribology Transactions · doi:10.1080/10402009108982050 · Cited by 83
The Effect of Material Properties on the Lubrication of Elastic Rollers
Dowson, D., & Higginson, G. R. (1960) · Journal of Mechanical Engineering Science · doi:10.1243/jmes_jour_1960_002_028_02 · Cited by 80
Metadata
- Authors
- Crook, A. W.
- Venue
- Philosophical Transactions of the Royal Society of London. Series A, Mathematical and Physical Sciences
- Publisher
- The Royal Society
- Published
- 1958-01-23
- Volume
- 250
- Issue
- 981
- Pages
- 387-409
- ISSN
- 0080-4614 (ISSN-L)
- 2054-0272
- OpenAlex
- W2052514883
- Cited by
- 174
- References
- 0
- FWCI
- 37.84
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The lubrication of rollers. https://app.cochat.ai/papers/10.1098/rsta.1958.0001
- The paper
- Crook, A. W. (1958). The lubrication of rollers. Philosophical Transactions of the Royal Society of London. Series A, Mathematical and Physical Sciences. https://doi.org/10.1098/rsta.1958.0001
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.