The DOI matches its Crossref record.
Fused deposition modeling of patient‐specific polymethylmethacrylate implants
Abstract
Purpose: The purpose of this paper is to investigate the use of medical‐grade polymethylmethacrylate (PMMA) in fused deposition modeling (FDM) to fabricate porous customized freeform structures for several applications including craniofacial reconstruction and orthopaedic spacers. It also aims to examine the effects of different fabrication conditions on porosity and mechanical properties of PMMA samples. Design/methodology/approach: The building parameters and procedures to properly and consistently extrude PMMA filament in FDM for building 3D structures were determined. Two experiments were performed that examined the effects of different fabrication conditions, including tip wipe frequency, layer orientation, and air gap (AG) (or distance between filament edges) on the mechanical properties and porosity of the fabricated structures. The samples were characterized through optical micrographs, and measurements of weight and dimensions of the samples were used to calculate porosity. The yield strength, strain, and modulus of elasticity of the samples were determined through compressive testing. Findings: Results show that both the tip wipe frequency (one wipe every layer or one wipe every ten layers) and layer orientation (transverse or axial with respect to the applied compressive load) used to fabricate the scaffolds have effects on the mechanical properties and resulting porosity. The samples fabricate in the transverse orientation with the high tip wipe frequency have a larger compressive strength and modulus than the lower tip wipe frequency samples (compressive strength: 16±0.97 vs 13±0.71 MPa, modulus: 370±14 vs 313±29 MPa, for the high vs low tip wipe frequency, respectively). Also, the samples fabricated in the transverse orientation have a larger compressive strength and modulus than the ones fabricated in the axial orientation (compressive strength: 16±0.97 vs 13±0.83 MPa, modulus: 370±14 vs 281±22 MPa; for samples fabricated with one tip wipe per layer in the transverse and axial orientations, respectively). In general, the stiffness and yield strength decreased when the porosity increased (compressive strength: 12±0.71 to 7±0.95 MPa, Modulus: 248±10 to 165±16 MPa, for samples with a porosity ranging from 55 to 70 percent). As a demonstration, FDM is successfully used to fabricate patient‐specific, 3D PMMA implants with varying densities, including cranial defect repair and femur models. Originality/value: This paper demonstrates that customized, 3D, biocompatible PMMA structures with varying porosities can be designed and directly fabricated using FDM. By enabling the use of PMMA in FDM, medical implants such as custom craniofacial implants can be directly fabricated from medical imaging data improving the current state of PMMA use in medicine.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Recent advances in 3D printing of biomaterials
Chia, H. N., & Wu, B. M. (2015) · Journal of Biological Engineering · doi:10.1186/s13036-015-0001-4 · Cited by 1,734
Polymeric Biomaterials for Medical Implants and Devices
Teo, A. J. T., Mishra, A., Park, I., Kim, Y.-J., Park, W.-T., & Yoon, Y.-J. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.5b00429 · Cited by 778
Mohan, N., Senthil, P., Vinodh, S., & Jayanth, N. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1274490 · Cited by 457
Extrusion-based additive manufacturing of PEEK for biomedical applications
Vaezi, M., & Yang, S. (2015) · Virtual and Physical Prototyping · doi:10.1080/17452759.2015.1097053 · Cited by 406
Waldbaur, A., Rapp, H., Länge, K., & Rapp, B. E. (2011) · Analytical Methods · doi:10.1039/c1ay05253e · Cited by 381
Metadata
- Authors
- Espalin, D., Arcaute, K., Rodriguez, D., Medina, F., Posner, M., & Wicker, R.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2010-04-27
- Volume
- 16
- Issue
- 3
- Pages
- 164-173
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2012264942
- Cited by
- 176
- References
- 0
- FWCI
- 14.42
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Fused deposition modeling of patient‐specific polymethylmethacrylate implants. https://app.cochat.ai/papers/10.1108/13552541011034825
- The paper
- Espalin, D., Arcaute, K., Rodriguez, D., Medina, F., Posner, M., & Wicker, R. (2010). Fused deposition modeling of patient‐specific polymethylmethacrylate implants. Rapid Prototyping Journal. https://doi.org/10.1108/13552541011034825
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.