The DOI matches its Crossref record; 4 of the 4 references it cites were found in a registry or an index.
Guidelines for etching silicon MEMS structures using fluorine high-density plasmas at cryogenic temperatures
Open accessAbstract
This paper presents guidelines for the deep reactive ion etching (DRIE) of silicon MEMS structures, employing SF/sub 6//O/sub 2/-based high-density plasmas at cryogenic temperatures. Procedures of how to tune the equipment for optimal results with respect to etch rate and profile control are described. Profile control is a delicate balance between the respective etching and deposition rates of a SiO/sub x/F/sub y/ passivation layer on the sidewalls and bottom of an etched structure in relation to the silicon removal rate from unpassivated areas. Any parameter that affects the relative rates of these processes has an effect on profile control. The deposition of the SiO/sub x/F/sub y/ layer is mainly determined by the oxygen content in the SF/sub 6/ gas flow and the electrode temperature. Removal of the SiO/sub x/F/sub y/ layer is mainly determined by the kinetic energy (self-bias) of ions in the SF/sub 6//O/sub 2/ plasma. Diagrams for profile control are given as a function of parameter settings, employing the previously published "black silicon method". Parameter settings for high rate silicon bulk etching, and the etching of micro needles and micro moulds are discussed, which demonstrate the usefulness of the diagrams for optimal design of etched features. Furthermore, it is demonstrated that in order to use the oxygen flow as a control parameter for cryogenic DRIE, it is necessary to avoid or at least restrict the presence of fused silica as a dome material, because this material may release oxygen due to corrosion during operation of the plasma source. When inert dome materials like alumina are used, etching recipes can be defined for a broad variety of microstructures in the cryogenic temperature regime. Recipes with relatively low oxygen content (1-10% of the total gas volume) and ions with low kinetic energy can now be applied to observe a low lateral etch rate beneath the mask, and a high selectivity (more than 500) of silicon etching with respect to polymers and oxide mask materials is obtained. Crystallographic preference etching of silicon is observed at low wafer temperature (-120/spl deg/C). This effect is enhanced by increasing the process pressure above 10 mtorr or for low ion energies (below 20 eV).
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Growth and Perfection of Crystals.
Vance, J. E. (1959) · Journal of the American Chemical Society · doi:10.1021/ja01522a099 · Cited by 1,385
Growth and perfection of crystals
Drew, J. B. (1959) · Journal of the Franklin Institute · doi:10.1016/0016-0032(59)90363-1 · Cited by 799
Esashi, M. (1998) · International Microprocesses and Nanotechnology Conference (MNC) · doi:10.1109/imnc.1998.729908 · Cited by 230
Micromachined needles for the transdermal delivery of drugs
Henry, S., McAllister, D. V., Allen, M. G., & Prausnitz, M. R. (2002) · IEEE International Conference on Micro Electro Mechanical Systems (MEMS) · doi:10.1109/memsys.1998.659807 · Cited by 117
Cited by
Enhanced Raman Scattering with Dielectrics
Alessandri, I., & Lombardi, J. R. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00365 · Cited by 655
Black silicon solar cells with interdigitated back-contacts achieve 22.1% efficiency
Savin, H., Repo, P., von Gastrow, G., Ortega, P., Calle, E., Garín, M., & Alcubilla, R. (2015) · Nature Nanotechnology · doi:10.1038/nnano.2015.89 · Cited by 586
Black silicon: fabrication methods, properties and solar energy applications
Liu, X., Coxon, P. R., Peters, M., Hoex, B., Cole, J. M., & Fray, D. J. (2014) · Energy Environ. Sci. · doi:10.1039/c4ee01152j · Cited by 511
Silicon micromachined hollow microneedles for transdermal liquid transport
Gardeniers, H. J. G. E., Luttge, R., Berenschot, E. J. W., de Boer, M. J., Yeshurun, S. Y., Hefetz, M., van-t Oever, R., & van den Berg, A. (2003) · Journal of Microelectromechanical Systems · doi:10.1109/jmems.2003.820293 · Cited by 413
Self-citationSurface tension-powered self-assembly of microstructures - The state-of-the-art
Syms, R. R. A., Yeatman, E. M., Bright, V. M., & Whitesides, G. M. (2003) · Journal of Microelectromechanical Systems · doi:10.1109/jmems.2003.811724 · Cited by 339
Metadata
- Authors
- de Boer, M. J., Gardeniers, J. G. E., Jansen, H. V., Smulders, E., Gilde, M.-J., Roelofs, G., Sasserath, J. N., & Elwenspoek, M.
- Venue
- Journal of Microelectromechanical Systems
- Published
- 2002-08
- Volume
- 11
- Issue
- 4
- Pages
- 385-401
- ISSN
- 1057-7157 (ISSN-L)
- OpenAlex
- W2109233209
- Cited by
- 266
- References
- 4
- FWCI
- 9.81
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.