Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 20 of the 22 references it cites were found in a registry or an index.

High-Power (>300 mW) On-Chip Laser With Passively Aligned Silicon-Nitride Waveguide DBR Cavity

Open access

Abstract

We demonstrate a high-power on-chip 1550-nm laser implemented by passive flip-chip integration of a curved-channel, double-pass InGaAsP/InP slab-coupled optical waveguide amplifier (SCOWA) onto a photonic integrated circuit (PIC) containing a silicon nitride (SiN) waveguide and distributed Bragg reflector (DBR) grating. The combined chip-scale SCOW external cavity laser (SCOWECL) has single mode emission with 312 mW of optical power at a drive current of 2.5 A, and exhibits a side mode suppression ratio (SMSR) of 55 dB, peak photon conversion efficiency (PCE) of 10%, low relative-intensity noise (RIN) of ~160 dB/Hz, and an integrated linewidth of 192 kHz. Additionally, we demonstrate a multi-wavelength SCOWECL array comprised of four SCOWAs coupled to SiN-waveguide DBR gratings. The four-element array generates 80 mW per channel when the SCOWAs are driven in parallel (1.25 A/channel) with ~1-nm wavelength spacing centered at 1533 nm. We describe the fabrication and hybrid integration processes. The measured SCOWA-to-waveguide coupling loss is estimated to be 1.6 +/-1.0 dB which agrees well with the simulation.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1109/jphot.2020.3037834

Cites

20 of 20 references verified0 citation errors · 0 not checkable

Statistics

Figures

Image 1
CC-BY · From the PDF
Image 2
CC-BY · From the PDF
Image 3
CC-BY · From the PDF
Image 4
CC-BY · From the PDF
Image 5
CC-BY · From the PDF
Image 6
CC-BY · From the PDF
Fig. 1 (a) Diagram of the top view of a single element and (b) 4-element SCOWA device hybridized in a photonic submount with SiN waveguides and DBR gratings. Schematics of (c) longitudinal and (d) transverse cross-sections of the single-element device architecture.
Fig. 1 (a) Diagram of the top view of a single element and (b) 4-element SCOWA device hybridized in a photonic submount with SiN waveguides and DBR gratings. Schematics of (c) longitudinal and (d) transverse cross-sections of the single-element device architecture.CC-BY · From the PDF
Fig. 2 Fabrication flow for the photonic multi-chip module submount, illustrating, (a) initial oxide bottom clad deposition, (b) LPCVD SiN waveguide layer deposition, (c) waveguide, DBR, and mode converter patterning, (d) trench etch for vertical-alignment pedestals, (e) oxide deposition for the top clad, and vertical-alignment pedestals, (f) resist masking and insert-slot trench etch (oxide boundary marked by dotted line), (g) passivation oxide deposition, (h) metal bond pad evaporation and liftoff, (i) indium solder bump array evaporation and liftoff.
Fig. 2 Fabrication flow for the photonic multi-chip module submount, illustrating, (a) initial oxide bottom clad deposition, (b) LPCVD SiN waveguide layer deposition, (c) waveguide, DBR, and mode converter patterning, (d) trench etch for vertical-alignment pedestals, (e) oxide deposition for the top clad, and vertical-alignment pedestals, (f) resist masking and insert-slot trench etch (oxide boundary marked by dotted line), (g) passivation oxide deposition, (h) metal bond pad evaporation and liftoff, (i) indium solder bump array evaporation and liftoff.CC-BY · From the PDF
Fig. 3 Optical and SEM images of the fabricated SiN multi-chip photonic submount, SCOWA device, and hybridized regions of the chip. The PIC submount (a) features 14 insert slot locations, with 6 mechanical stops at each insert slot (light blue color). The fabricated SCOWA wafer and a single element and 4-element device are shown (b). Three single-element devices have been flip-chip bonded into the bottom left 3 insert slots of the submount shown in (a). An optical microscope image of the front region of the insert slot (c) shows the bottom P-electrode contact pad, indium solder bump array, and the input facet region. The SiN waveguide is visible (black line) in the oxide region of the PIC (purple region). A SEM image of the DBR grating structure showing 200-nm wide posts, and 1.1µ m wide waveguide (d). A tilted SEM view of the input region is shown in image (e) illustrating the location of waveguide, and the wall of the 10µ m deep insert slot. A top-down SEM image of an insert slot with a SCOWA device flip-chip bonded into position is visible in image (f), here the III-V device has been placed on-top of the indium bump array that was visible in image (d), and the emitting face abuts the input facet region with a 0.8µ m separation gap. The triangular mark on the left side of the image is a fiducial mark to help in aligning the III-V edge with the input facet.
Fig. 3 Optical and SEM images of the fabricated SiN multi-chip photonic submount, SCOWA device, and hybridized regions of the chip. The PIC submount (a) features 14 insert slot locations, with 6 mechanical stops at each insert slot (light blue color). The fabricated SCOWA wafer and a single element and 4-element device are shown (b). Three single-element devices have been flip-chip bonded into the bottom left 3 insert slots of the submount shown in (a). An optical microscope image of the front region of the insert slot (c) shows the bottom P-electrode contact pad, indium solder bump array, and the input facet region. The SiN waveguide is visible (black line) in the oxide region of the PIC (purple region). A SEM image of the DBR grating structure showing 200-nm wide posts, and 1.1µ m wide waveguide (d). A tilted SEM view of the input region is shown in image (e) illustrating the location of waveguide, and the wall of the 10µ m deep insert slot. A top-down SEM image of an insert slot with a SCOWA device flip-chip bonded into position is visible in image (f), here the III-V device has been placed on-top of the indium bump array that was visible in image (d), and the emitting face abuts the input facet region with a 0.8µ m separation gap. The triangular mark on the left side of the image is a fiducial mark to help in aligning the III-V edge with the input facet.CC-BY · From the PDF
Image 10
CC-BY · From the PDF
Fig. 4 Optical images of the alignment fiducials of the SCOWA and PIC submount as captured from the SET FC 150 vision system (a) and (b). In image (a) are the Vernier marks used for lateral alignment of the SCOWA chip in green, and the underlying Au marks visible in yellow. The Vernier constant is 0.4 µ m allowing us to readily identify shifting left or right up to 2.0 µ m, in this image the two chips are aligned and nearly centered with blue arrow marking the centered position. In top half of image (b) the front input facet of the PIC is visible with the SiN waveguide taper visible in the transparent cladding oxide in the trapezoidal shaped input region. In the lower half of the image the 5µ m wide ridge of the SCOWA is seen. The pair of nearly touching Au triangles define a target gap of ∼ 1.5 µ m serve as visual markers for aligning the SCOWA front edge (note for the case illustrated here the SCOWA chip is nearly touching the input facet, and would be shifted further down prior to initiating the bond. Image (c) is an IR microscope image of a flip chip bonded device showing centered Vernier marks.
Fig. 4 Optical images of the alignment fiducials of the SCOWA and PIC submount as captured from the SET FC 150 vision system (a) and (b). In image (a) are the Vernier marks used for lateral alignment of the SCOWA chip in green, and the underlying Au marks visible in yellow. The Vernier constant is 0.4 µ m allowing us to readily identify shifting left or right up to 2.0 µ m, in this image the two chips are aligned and nearly centered with blue arrow marking the centered position. In top half of image (b) the front input facet of the PIC is visible with the SiN waveguide taper visible in the transparent cladding oxide in the trapezoidal shaped input region. In the lower half of the image the 5µ m wide ridge of the SCOWA is seen. The pair of nearly touching Au triangles define a target gap of ∼ 1.5 µ m serve as visual markers for aligning the SCOWA front edge (note for the case illustrated here the SCOWA chip is nearly touching the input facet, and would be shifted further down prior to initiating the bond. Image (c) is an IR microscope image of a flip chip bonded device showing centered Vernier marks.CC-BY · From the PDF
Image 12
CC-BY · From the PDF
Fig. 5 (a) Power vs current (L-I) and electrical efficiency from three hybridized single-element InGaAsP/InP SCOECL devices biased up to 2.5A T = 25°C. The best-aligned of the three devices (A) emits 312 mW at 2.5A. (b) L-I plot for a 4-element SCOWECL device showing ∼ 80 mW emitted for each waveguide channel at a bias of 1.25 A per SCOWA (5 A total)T = 25°C.
Fig. 5 (a) Power vs current (L-I) and electrical efficiency from three hybridized single-element InGaAsP/InP SCOECL devices biased up to 2.5A T = 25°C. The best-aligned of the three devices (A) emits 312 mW at 2.5A. (b) L-I plot for a 4-element SCOWECL device showing ∼ 80 mW emitted for each waveguide channel at a bias of 1.25 A per SCOWA (5 A total)T = 25°C.CC-BY · From the PDF
Fig. 6 (a) Optical spectrum of single-element SCOWECL A, showing single longitudinal-mode emission with 55 dB SMSR at 2.2A bias. The left inset image shows a wide wavelength scan showing that no other lasing peaks are visible from 1440-1640 nm. (b) Optical spectra of a 4-element emitter biased at 2.0 A coupled to 4 waveguides with 0.5 nm pitch variation on the DBR gratings creating ∼ 1 nm wavelength off-sets in the emission spectrum. Insets on both figures show the mode image captured by focusing the emission from the PIC output facet through an aspherical lens onto an Infra-red camera.
Fig. 6 (a) Optical spectrum of single-element SCOWECL A, showing single longitudinal-mode emission with 55 dB SMSR at 2.2A bias. The left inset image shows a wide wavelength scan showing that no other lasing peaks are visible from 1440-1640 nm. (b) Optical spectra of a 4-element emitter biased at 2.0 A coupled to 4 waveguides with 0.5 nm pitch variation on the DBR gratings creating ∼ 1 nm wavelength off-sets in the emission spectrum. Insets on both figures show the mode image captured by focusing the emission from the PIC output facet through an aspherical lens onto an Infra-red camera.CC-BY · From the PDF
Image 15
CC-BY · From the PDF
Fig. 8 Plot of optical power of single element SCOWECL devices biased at 2.5 A (T = 25.0°C) and coupling loss plotted against the measured lateral off-set position as determined from IR microcsopy of overlay Vernier alignment fiducials at the device bond interface.
Fig. 8 Plot of optical power of single element SCOWECL devices biased at 2.5 A (T = 25.0°C) and coupling loss plotted against the measured lateral off-set position as determined from IR microcsopy of overlay Vernier alignment fiducials at the device bond interface.CC-BY · From the PDF
Image 17
CC-BY · From the PDF
Fig. 10 Plot of measured (symbols) and simulated (solid line) coupling loss from four single-element SCOWECLs, as a function of lateral positional alignment between the SCOWA and SiN waveguides.
Fig. 10 Plot of measured (symbols) and simulated (solid line) coupling loss from four single-element SCOWECLs, as a function of lateral positional alignment between the SCOWA and SiN waveguides.CC-BY · From the PDF

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 22 references

Research works printed but not linked: 2

  1. Y. Fan et al., "Hybrid integrated inp-Si3N4 diode laser with a 40-Hz intrinsic linewidth," Opt. Exp., vol. 28, pp. 21713-21728, 2020.
  2. D. T. Spencer, M. Davenport, S. Srinivasan, J. Khurgin, P. A. Morton, and J. E. Bowers, "Low kappa, narrow bandwidth Si3N4 bragg gratings," Opt. Exp., vol. 23, pp. 30329-30336, 2015.

Cited by

See all 35

Metadata

Authors
Kharas, D., Plant, J. J., Loh, W., Swint, R. B., Bramhavar, S., Heidelberger, C., Yegnanarayanan, S., & Juodawlkis, P. W.
Affiliations
MIT Lincoln Laboratory (US)
Venue
IEEE Photonics Journal
Published
2020-12
Volume
12
Issue
6
Pages
1-12
ISSN
  • 1943-0647 (ISSN-L)
  • 1943-0655
OpenAlex
W3104153322
Cited by
34
References
22
Citations by year
2026: 2 · 2025: 10 · 2024: 6 · 2023: 4 · 2022: 8 · 2021: 4
FWCI
1.37
Type
journal article
Language
en
Open access
Locations
  • IEEE photonics journal (publishedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Funders
United States Air Force under Air Force (FA8702-15-D-0001)
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Photonic and Optical Devices
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Semiconductor Lasers and Optical Devices
  • Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Photorefractive and Nonlinear Optics
Keywords
on-chip lasers, high-power lasers, silicon nitride waveguides, external cavity laser, flip-chip integration, multi-wavelength laser array, 1550 nm, side-mode suppression ratio, photon conversion efficiency, relative intensity noise, line width, photonic integrated circuits

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: High-Power (>300 mW) On-Chip Laser With Passively Aligned Silicon-Nitride Waveguide DBR Cavity. https://app.cochat.ai/papers/10.1109/jphot.2020.3037834
The paper
Kharas, D., Plant, J. J., Loh, W., Swint, R. B., Bramhavar, S., Heidelberger, C., Yegnanarayanan, S., & Juodawlkis, P. W. (2020). High-Power (>300 mW) On-Chip Laser With Passively Aligned Silicon-Nitride Waveguide DBR Cavity. IEEE Photonics Journal. https://doi.org/10.1109/jphot.2020.3037834

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.