Global Identification of a Low-Order Lumped-Parameter Thermal Network for Permanent Magnet Synchronous Motors
The DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index.
Abstract
Monitoring critical temperatures in permanent magnet synchronous motors (PMSM) is essential to prevent device failures or excessive motor life-time reduction due to thermal stress. A lumped-parameter thermal network (LPTN) consisting of four nodes is designed to model the most important motor parts, i.e., the stator yoke, stator winding, stator teeth, and the permanent magnets. An empirical approach based on the comprehensive experimental training data and a particle swarm optimization are used to identify the LPTN parameters of a 60-kW automotive traction PMSM. Varying parameters and physically motivated constraints are taken into account to extend the model scope beyond the training data domain. Here, a so-called global identification technique for linear parameter-varying systems is innovatively applied to a thermal motor model for the first time. The model accuracy is cross-validated with independent load profiles, and a maximum estimation error (worst-case) of 8°C regarding all considered motor temperatures is achieved. Also, a comprehensive residual statistical analysis proves suitable estimation results in terms of model robustness and accuracy.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Kennedy, J., & Eberhart, R. (2002) · Proceedings of ICNN'95 - International Conference on Neural Networks · doi:10.1109/icnn.1995.488968 · Cited by 58,192
Clerc, M. (2006) · Wiley eBooks · doi:10.1002/9780470612163 · Cited by 1,622
Lumped parameter thermal model for electrical machines of TEFC design
Mellor, P. H., Roberts, D., & Turner, D. R. (1991) · IEE Proceedings B Electric Power Applications · doi:10.1049/ip-b.1991.0025 · Cited by 885 · cited 5×
“However, white-box approaches based on the classical T-equivalent-circuit-method [25] or the k-shift-approach [32] still lead to large differentialalgebraic-equation systems.”
BackgroundMethodInfluentialModeling and Identification of Linear Parameter-Varying Systems
Tóth, R. (2010) · Lecture Notes in Control and Information Sciences · doi:10.1007/978-3-642-13812-6 · Cited by 598 · cited 1×
“tion can be realized in two different ways [38], [39]: Following the local approach several independent experiments are carried out in the complete scheduling plane (operation area of the”
BackgroundAir-Gap Convection in Rotating Electrical Machines
Howey, D. A., Childs, P. R. N., & Holmes, A. S. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2100337 · Cited by 331 · cited 3×
“To limit the search room the maximum values ai,j,max , bi,j,max , and Ri,j,0,max are conservatively estimated based on the analytical formulations in [37] and [54] in advance.”
BackgroundMethodEstimation of Equivalent Thermal Parameters of Impregnated Electrical Windings
Simpson, N., Wrobel, R., & Mellor, P. H. (2013) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2013.2263271 · Cited by 291 · cited 1×
“[53].”
Temperature effects on torque production and efficiency of PM motors using NdFeB magnets
Sebastian, T. (1995) · IEEE Transactions on Industry Applications · doi:10.1109/28.370284 · Cited by 246
A Practical Thermal Model for the Estimation of Permanent Magnet and Stator Winding Temperatures
Kral, C., Haumer, A., & Lee, S. B. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2253128 · Cited by 206 · cited 1×
“However, in the field of thermal motor modeling [17], [19], [20], [22] and also other engineering applications [38], [41], [42], the local approach is clearly dominating in the existing literature.”
BackgroundIdentification of Linear Parameter-Varying Systems Using Nonlinear Programming
Lee, L. H., & Poolla, K. R. (1999) · Journal of Dynamic Systems Measurement and Control · doi:10.1115/1.2802444 · Cited by 176
Magnet Temperature Estimation in Surface PM Machines Using High-Frequency Signal Injection
Reigosa, D. D., Briz, F., García, P., Guerrero, J. M., & Degner, M. W. (2010) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2010.2049816 · Cited by 172
Temperature effects on torque production and efficiency of PM motors using NdFeB magnets
Sebastian, T. (2002) · Conference Record of the 1993 IEEE Industry Applications Conference Twenty-Eighth IAS Annual Meeting · doi:10.1109/ias.1993.298907 · Cited by 167 · cited 1×
“, torque accuracy due to PM flux linkage variation) can be compensated, if real-time temperature information is available [6], [7].”
BackgroundOptimal Control of Traction Motor Drives Under Electrothermal Constraints
Lemmens, J., Vanassche, P., & Driesen, J. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2299765 · Cited by 157 · cited 1×
“Realtime temperature estimation of critical motor components can be used as the input quantities of derating controllers [3].”
BackgroundWilson, S. D., Stewart, P., & Taylor, B. (2010) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2010.2051811 · Cited by 125 · cited 1×
“, NdFeB) show only a low temperature sensitivity, and the ohmic voltage drop in high-power machines is only small in contrast to the total terminal voltage [14].”
BackgroundIdentification in Parametric Models
Bekker, P. A., & Wansbeek, T. J. (2003) · Wiley eBooks · doi:10.1002/9780470996249.ch8 · Cited by 106
Identification of linear parametrically varying systems
Nemani, M., Ravikanth, R., & Bamieh, B. A. (2002) · IEEE Conference on Decision and Control (CDC) · doi:10.1109/cdc.1995.478600 · Cited by 76 · cited 1×
“Only in purely academic and artificial studies [43], [44] and in the context of a simplified transformer LPTN with simple load profiles (especially without overload operation) [45] global LPV identifications can be found.”
BackgroundRothe, R., & Hameyer, K. (2011) · IEEE International Electric Machines & Drives Conference (IEMDC) · doi:10.1109/iemdc.2011.5994793 · Cited by 49 · cited 1×
“Beside the prevention of partial or total motor destruction, intensive thermal stress can lead to a shortened device life-time [1], [2].”
Background
Cited by
Rafaq, M. S., & Jung, J.-W. (2020) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2019.2944413 · Cited by 266
Thermal Parameter and State Estimation for Digital Twins of E-Powertrain Components
Rodriguez, B., Sanjurjo, E., Tranchero, M., Romano, C., & Gonzalez, F. (2021) · IEEE Access · doi:10.1109/access.2021.3094312 · Cited by 49
Metadata
- Authors
- Wallscheid, O., & Bocker, J.
- Venue
- IEEE Transactions on Energy Conversion
- Published
- 2016-03
- Volume
- 31
- Issue
- 1
- Pages
- 354-365
- ISSN
- 0885-8969 (ISSN-L)
- 1558-0059
- OpenAlex
- W2288981278
- Cited by
- 242
- References
- 16
- FWCI
- 3.69
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.