Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs
The DOI matches its Crossref record; 35 of the 40 references it cites were found in a registry or an index.
Abstract
A computational model is proposed for the prediction of friction-related mechanical efficiency losses of parallel-axis gear pairs. The model incorporates a gear load distribution model, a friction model, and a mechanical efficiency formulation to predict the instantaneous mechanical efficiency of a gear pair under typical operating, surface, and lubrication conditions. The friction model uses a new friction coefficient formula obtained by using a validated non-Newtonian thermal elastohydrodynamic lubrication (EHL) model in conjunction with a multiple linear regression analysis. The load and friction coefficient distribution predictions are used to compute instantaneous torque/power losses and the mechanical efficiency of a gear pair at any given rotational position. Efficiency measurements from gear pairs having various gear designs and surface treatments are compared to model predictions. Mechanical efficiency predictions are shown to be within 0.1% of the measured values, indicating that the proposed efficiency model is accurate. Results of a parametric study are presented at the end to highlight the influence of key basic gear geometric parameters, tooth modifications, operating conditions, surface finish, and lubricant properties on mechanical efficiency losses.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Gear Geometry and Applied Theory
Litvin, F. L., & Fuentes, A. (2004) · Cambridge University Press eBooks · doi:10.1017/cbo9780511547126 · Cited by 2,332
Elasto-Hydrodynamic Lubrication
(1977) · Elsevier eBooks · doi:10.1016/c2013-0-05764-7 · Cited by 591
Applied Tribology: Bearing Design and Lubrication
Kennedy, F. E. (2002) · Journal of Tribology · doi:10.1115/1.1432665 · Cited by 325
Handbook of Practical Gear Design
Dudley, D. W. (1984) · Medical Entomology and Zoology · Cited by 286
Applied Tribology: Bearing Design and Lubrication
Khonsari, M. M., & Booser, E. R. (2017) · Wiley eBooks · doi:10.1002/9781118700280 · Cited by 235
Instantaneous Coefficients of Gear Tooth Friction
Benedict, G. H., & Kelley, B. W. (1961) · A S L E Transactions · doi:10.1080/05698196108972420 · Cited by 201
Fourth Paper: Shear Behaviour of Elastohydrodynamic Oil Films at High Rolling Contact Pressures
Johnson, K. L., & Cameron, R. (1967) · Proceedings of the Institution of Mechanical Engineers · doi:10.1243/pime_proc_1967_182_029_02 · Cited by 162
Development of a generalized mechanical efficiency prediction methodology for gear pairs
Xu, H. J. (2005) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 161
Self-citationChittenden, R. J., Dowson, D., Dunn, J. F., & Taylor, C. M. (1985) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1985.0015 · Cited by 155
Conry, T. F., & Seireg, A. (1973) · Journal of Engineering for Industry · doi:10.1115/1.3438259 · Cited by 145
Dowson, D., & Higginson, G. R. (1977) · Elsevier eBooks · doi:10.1016/b978-0-08-021302-6.50012-6 · Cited by 122
The Geometry of Involute Gears
Colbourne, J. R., & Errichello, R. (1988) · Journal of Mechanisms Transmissions and Automation in Design · doi:10.1115/1.3258895 · Cited by 101
Elasto–Hydrodynamic Lubrication
Hirani, H. (2016) · Cambridge University Press eBooks · doi:10.1017/cbo9781107479975.007 · Cited by 97
Determination of power losses in gear transmissions with rolling and sliding friction incorporated
Michlin, Y. H., & Myunster, V. (2002) · Mechanism and Machine Theory · doi:10.1016/s0094-114x(01)00070-2 · Cited by 92
A review of friction predictions in gear teeth
Martin, K. F. (1978) · Wear · doi:10.1016/0043-1648(78)90088-1 · Cited by 91
Effect of Geometry and Operating Conditions on Spur Gear System Power Loss
Anderson, N. E., & Loewenthal, S. H. (1981) · Journal of Mechanical Design · doi:10.1115/1.3254854 · Cited by 89
Self-citationFriction and Temperature in Rolling Sliding Contacts
O'Donoghue, J. P., & Cameron, A. (1966) · A S L E Transactions · doi:10.1080/05698196608972134 · Cited by 83
A Friction Model of Partial-EHL Contacts and its Application to Power Loss in Spur Gears
Wu, S., & Cheng, H. S. (1991) · Tribology Transactions · doi:10.1080/10402009108982050 · Cited by 83
Friction and scoring under the conditions of Simultaneous rolling and sliding of bodies
Drozdov, Y. N., & Gavrikov, Y. A. (1968) · Wear · doi:10.1016/0043-1648(68)90177-4 · Cited by 73
Design of Spur Gears for Improved Efficiency
Anderson, N. E., & Loewenthal, S. H. (1982) · Journal of Mechanical Design · doi:10.1115/1.3256434 · Cited by 68
Self-citationApplication of EHD Oil Film Theory to Industrial Gear Drives
Wellauer, E. J., & Holloway, G. A. (1976) · Journal of Engineering for Industry · doi:10.1115/1.3438951 · Cited by 62
Efficiency of Nonstandard and High Contact Ratio Involute Spur Gears
Anderson, N. E., & Loewenthal, S. H. (1986) · Journal of Mechanisms, Transmissions, and Automation in Design · doi:10.1115/1.3260774 · Cited by 58
Self-citationThe Efficiency of Involute Spur Gears
Martin, K. F. (1981) · Journal of Mechanical Design · doi:10.1115/1.3254855 · Cited by 57
Review of Gear Efficiency Equation and Force Treatment
Yada, T. (1997) · JSME international journal Ser C Dynamics control robotics design and manufacturing · doi:10.1299/jsmec1993.40.1 · Cited by 48
Determining Power Losses in Helical Gear Mesh: Case Study
Heingartner, P., & Mba, D. (2003) · IEEE/ASME International Conference on Mechatronic and Embedded Systems and Applications · doi:10.1115/detc2003/ptg-48118 · Cited by 47
Cioc, C., Cioc, S., Moraru, L., Kahraman, A., & Keith, T. G. (2002) · Tribology Transactions · doi:10.1080/10402000208982587 · Cited by 35
Self-citationStudies on Frictional Loss, Temperature Rise and Limiting Load for Scoring of Spur Gear
Naruse, C., HAIZUKA, S., Nemoto, R., et al. (1986) · Bulletin of JSME · doi:10.1299/jsme1958.29.600 · Cited by 30
Thermo-EHD Analysis of Lubrication of Helical Gears
Simon, V. V. (1988) · Journal of Mechanisms Transmissions and Automation in Design · doi:10.1115/1.3267466 · Cited by 26
EHD Lubricant Film Thickness Formulas for Power Transmission Gears
Akin, L. S. (1974) · Journal of Lubrication Technology · doi:10.1115/1.3451989 · Cited by 26
Predicting the Coefficient of Friction in Sliding-Rolling Contacts
Li, Y., & Seireg, A. A. (1989) · Journal of Tribology · doi:10.1115/1.3261930 · Cited by 15
Frictional and Thermal Behaviors of Sliding-Rolling Concentrated Contacts
Ku, P. M., Staph, H. E., & Carper, H. J. (1978) · Journal of Lubrication Technology · doi:10.1115/1.3453101 · Cited by 15
Development of an efficiency test methodology for high-speed gearboxes
Chase, D. (2005) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 14
Fundamental Research on Gear Lubrication
SASAKI, T., OKAMURA, K., & ISOGAI, R. (1961) · Bulletin of JSME · doi:10.1299/jsme1958.4.382 · Cited by 6
Study of Influence of Helix Angle on Friction Characteristics of Helical Gears
HAIZUKA, S., Naruse, C., & Yamanaka, T. (1999) · Tribology Transactions · doi:10.1080/10402009908982256 · Cited by 6
Modeling and Analysis of Sliding Friction in Gear Dynamics
Vaishya, M., & Houser, D. R. (2000) · Volume 6: 8th International Power Transmission and Gearing Conference · doi:10.1115/detc2000/ptg-14431
Research works printed but not linked: 7
- Reuleaux, Friction in Tooth Gearing, Trans. ASME, VIII, 45
- Kelley, Lubrication of Involute Gearing, Proc. Inst. Mech. Eng., 182, 173
- Dowson, A Theory of Involute Gear Lubrication, 8
- Simon, V. , 1981, “Load Capacity and Efficiency of Spur Ears in Regard to Thermo-End Lubrication,” International Symposium on Gearing and Power Transmissions, Tokyo, Japan.
- Mihalidis, A., Bakolas, V., Panagiotidis, K., and Drivakos, N., 2002, “Prediction of the Friction Coefficient of Spur Gear Pairs,” VDI-Berichte, NR. 1665, pp. 705–719.
- Chittenden, A Theoretical Analysis of The Isothermal Elastohydrodynamic Lubricant of Concentrated Contacts, Proc. R. Soc. London, Ser. A, 397, 271
- Johnson, Shear Behavior of Elastohydrodynamic Oil Films at High Rolling Contact Pressures, Proc. Inst. Mech. Eng., 182, 307
Cited by
An Experimental Investigation of Spur Gear Efficiency
Petry-Johnson, T. T., Kahraman, A., Anderson, N. E., & Chase, D. R. (2008) · Journal of Mechanical Design · doi:10.1115/1.2898876 · Cited by 205
“A large number of theoretical studies have been published on the efficiency of gear trains [ 1-16 ].”
BackgroundMethodResultInfluentialSelf-citationA tribo-dynamic model of a spur gear pair
Li, S., & Kahraman, A. (2013) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2013.04.022 · Cited by 177
“[28] compared the impacts of different friction models on power losses to indicate that the constant friction coefficient assumption is not accurate through comparisons to benchmark experiments.”
Self-citationLi, S., & Kahraman, A. (2010) · Tribology Transactions · doi:10.1080/10402000903502279 · Cited by 149
“( 3 ) provided a detailed review of these earlier gear efficiency studies, indicating that (a) the friction coefficient along the tooth surface is not constant but varies significantly, and (b) the empirical friction formulae are usually valid within narrow ranges that the experimental conditions and lubricants repres…”
BackgroundSelf-citationLoad-Independent Spin Power Losses of a Spur Gear Pair: Model Formulation
Seetharaman, S., & Kahraman, A. (2009) · Journal of Tribology · doi:10.1115/1.3085943 · Cited by 176
Self-citationOn optimal tooth profile modification for reduction of vibration and noise in spur gear pairs
Ghosh, S., & Chakraborty, G. (2016) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2016.06.008 · Cited by 139
Metadata
- Authors
- Xu, H., Kahraman, A., Anderson, N. E., & Maddock, D. G.
- Affiliations
- The Ohio State University (US)
- General Motors (United States) (US)
- Venue
- Journal of Mechanical Design
- Publisher
- ASME International
- Published
- 2006-06-14
- Volume
- 129
- Issue
- 1
- Pages
- 58-68
- ISSN
- 0161-8458 (ISSN-L)
- 1050-0472
- 1528-9001
- OpenAlex
- W1970036055
- Semantic Scholar
- e4f46f1dbb4c333508d9b97b58992c11dcdd3355
- Cited by
- 323
- References
- 40
- Citations by year
- 2026: 22 · 2025: 31 · 2024: 28 · 2023: 23 · 2022: 25 · 2021: 26 · 2020: 23 · 2019: 15 · 2018: 20 · 2017: 13 · 2016: 12 · 2015: 17 · 2014: 19 · 2013: 11 · 2012: 9
- FWCI
- 13.71
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Mechanical Design (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanics of Materials › Tribology and Wear Analysis
- Keywords
- parallel-axis gears, friction losses, gear load distribution, friction coefficient, elastohydrodynamic lubrication, non-Newtonian lubrication, tooth modification, lubricant properties, gear geometry
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.