Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs
The DOI matches its Crossref record; 35 of the 40 references it cites were found in a registry or an index.
Abstract
A computational model is proposed for the prediction of friction-related mechanical efficiency losses of parallel-axis gear pairs. The model incorporates a gear load distribution model, a friction model, and a mechanical efficiency formulation to predict the instantaneous mechanical efficiency of a gear pair under typical operating, surface, and lubrication conditions. The friction model uses a new friction coefficient formula obtained by using a validated non-Newtonian thermal elastohydrodynamic lubrication (EHL) model in conjunction with a multiple linear regression analysis. The load and friction coefficient distribution predictions are used to compute instantaneous torque/power losses and the mechanical efficiency of a gear pair at any given rotational position. Efficiency measurements from gear pairs having various gear designs and surface treatments are compared to model predictions. Mechanical efficiency predictions are shown to be within 0.1% of the measured values, indicating that the proposed efficiency model is accurate. Results of a parametric study are presented at the end to highlight the influence of key basic gear geometric parameters, tooth modifications, operating conditions, surface finish, and lubricant properties on mechanical efficiency losses.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Gear Geometry and Applied Theory
Litvin, F. L., & Fuentes, A. (2004) · Cambridge University Press eBooks · doi:10.1017/cbo9780511547126 · Cited by 2,332
Elasto-Hydrodynamic Lubrication
(1977) · Elsevier eBooks · doi:10.1016/c2013-0-05764-7 · Cited by 591
Applied Tribology: Bearing Design and Lubrication
Kennedy, F. E. (2002) · Journal of Tribology · doi:10.1115/1.1432665 · Cited by 325
Handbook of Practical Gear Design
Dudley, D. W. (1984) · Medical Entomology and Zoology · Cited by 286
Applied Tribology: Bearing Design and Lubrication
Khonsari, M. M., & Booser, E. R. (2017) · Wiley eBooks · doi:10.1002/9781118700280 · Cited by 235
Instantaneous Coefficients of Gear Tooth Friction
Benedict, G. H., & Kelley, B. W. (1961) · A S L E Transactions · doi:10.1080/05698196108972420 · Cited by 201
Fourth Paper: Shear Behaviour of Elastohydrodynamic Oil Films at High Rolling Contact Pressures
Johnson, K. L., & Cameron, R. (1967) · Proceedings of the Institution of Mechanical Engineers · doi:10.1243/pime_proc_1967_182_029_02 · Cited by 162
Development of a generalized mechanical efficiency prediction methodology for gear pairs
Xu, H. J. (2005) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 161
Self-citationChittenden, R. J., Dowson, D., Dunn, J. F., & Taylor, C. M. (1985) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1985.0015 · Cited by 155
Conry, T. F., & Seireg, A. (1973) · Journal of Engineering for Industry · doi:10.1115/1.3438259 · Cited by 145
Research works printed but not linked: 7
- Reuleaux, Friction in Tooth Gearing, Trans. ASME, VIII, 45
- Kelley, Lubrication of Involute Gearing, Proc. Inst. Mech. Eng., 182, 173
- Dowson, A Theory of Involute Gear Lubrication, 8
- Simon, V. , 1981, “Load Capacity and Efficiency of Spur Ears in Regard to Thermo-End Lubrication,” International Symposium on Gearing and Power Transmissions, Tokyo, Japan.
- Mihalidis, A., Bakolas, V., Panagiotidis, K., and Drivakos, N., 2002, “Prediction of the Friction Coefficient of Spur Gear Pairs,” VDI-Berichte, NR. 1665, pp. 705–719.
- Chittenden, A Theoretical Analysis of The Isothermal Elastohydrodynamic Lubricant of Concentrated Contacts, Proc. R. Soc. London, Ser. A, 397, 271
- Johnson, Shear Behavior of Elastohydrodynamic Oil Films at High Rolling Contact Pressures, Proc. Inst. Mech. Eng., 182, 307
Cited by
An Experimental Investigation of Spur Gear Efficiency
Petry-Johnson, T. T., Kahraman, A., Anderson, N. E., & Chase, D. R. (2008) · Journal of Mechanical Design · doi:10.1115/1.2898876 · Cited by 205
“A large number of theoretical studies have been published on the efficiency of gear trains [ 1-16 ].”
BackgroundMethodResultInfluentialSelf-citationA tribo-dynamic model of a spur gear pair
Li, S., & Kahraman, A. (2013) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2013.04.022 · Cited by 177
“[28] compared the impacts of different friction models on power losses to indicate that the constant friction coefficient assumption is not accurate through comparisons to benchmark experiments.”
Self-citationLi, S., & Kahraman, A. (2010) · Tribology Transactions · doi:10.1080/10402000903502279 · Cited by 149
“( 3 ) provided a detailed review of these earlier gear efficiency studies, indicating that (a) the friction coefficient along the tooth surface is not constant but varies significantly, and (b) the empirical friction formulae are usually valid within narrow ranges that the experimental conditions and lubricants repres…”
BackgroundSelf-citationLoad-Independent Spin Power Losses of a Spur Gear Pair: Model Formulation
Seetharaman, S., & Kahraman, A. (2009) · Journal of Tribology · doi:10.1115/1.3085943 · Cited by 176
Self-citationOn optimal tooth profile modification for reduction of vibration and noise in spur gear pairs
Ghosh, S., & Chakraborty, G. (2016) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2016.06.008 · Cited by 139
Shi, J., Gou, X.-F., & Zhu, L. (2019) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2019.01.018 · Cited by 138
Hu, B., Zhou, C., Wang, H., et al. (2020) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2020.107509 · Cited by 132
Prediction of dynamic friction forces in spur gears using alternate sliding friction formulations
He, S. L., Cho, S., & Singh, R. G. (2007) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2007.06.077 · Cited by 129
“[9,10] based on non-Newtonian, thermal EHL theory, is modified in our work to incorporate a reversal in the direction of the friction force at the pitch point as mXiðtÞ 1⁄4 e ðSRiðtÞ;PhiðtÞ;ZM ;SavgÞP2 hi jSRiðtÞj 3V6 ei ðtÞZ b7 MR b8 i ðtÞ sgn1⁄2modðOprbpt; lÞ þ ðn iÞl LAP , f ðSRiðtÞ;PhiðtÞ; ZM ;SavgÞ 1⁄4 b1 þ b4jSR…”
BackgroundMethodInfluentialDynamical modeling and experimental validation for tooth pitting and spalling in spur gears
Luo, Y., Baddour, N., & Liang, M. (2018) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2018.09.027 · Cited by 124
Influence factors on gearbox power loss
Michaelis, K., Höhn, B., & Hinterstoißer, M. (2011) · Industrial Lubrication and Tribology · doi:10.1108/00368791111101830 · Cited by 122
“Power loss reduction at the end of the power train has a large impact on the overall optimisation, although absolute efficiency in gearboxes and rear axles is already high (Xu et al., 2007).”
BackgroundPrediction of mechanical gear mesh efficiency of hypoid gear pairs
Kolivand, M., Li, S., & Kahraman, A. (2010) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2010.06.015 · Cited by 117
Self-citationTian, Q., Xiao, Q., Sun, Y., et al. (2014) · Multibody System Dynamics · doi:10.1007/s11044-014-9420-0 · Cited by 104
Numerical and experimental investigation of drag torque in a two-speed dual clutch transmission
Zhou, X., Walker, P. D., Zhang, N., Zhu, B., & Ruan, J. (2014) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2014.04.007 · Cited by 109
“The total drag torque within a gear-train for any transmission is generallymade up of several parts, including gear friction [3–6], windage [7–9] and oil churning [10,11].”
BackgroundMulti-objective optimization of gear unit design to improve efficiency and transmission error
Younes, E. B., Changenet, C., Bruyère, J., Rigaud, E., & Perret-Liaudet, J. (2021) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2021.104499 · Cited by 103
“Additionally, the gear responds favorably to the performance, precision and specific power requirements imposed in the modern mechanical architectures [1].”
BackgroundPrediction of friction-related power losses of hypoid gear pairs
Xu, H., & Kahraman, A. (2007) · Proceedings of the Institution of Mechanical Engineers Part K Journal of Multi-body Dynamics · doi:10.1243/14644193jmbd48 · Cited by 105
Self-citationVelex, P., & Ville, F. (2009) · Journal of Mechanical Design · doi:10.1115/1.3179156 · Cited by 79
Huangfu, Y., Dong, X., Chen, K., et al. (2022) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2022.107157 · Cited by 78
A thermal tribo-dynamic mechanical power loss model for spur gear Pairs
Li, S. (2015) · Tribology International · doi:10.1016/j.triboint.2015.03.022 · Cited by 84
Verstraten, T., Mathijssen, G., Furnémont, R., Vanderborght, B., & Lefeber, D. (2015) · Mechatronics · doi:10.1016/j.mechatronics.2015.07.004 · Cited by 82
Salgado, D. R., & del Castillo, J. M. (2013) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2013.11.001 · Cited by 75
Huang, K., Xiong, Y., Wang, T., et al. (2016) · Applied Surface Science · doi:10.1016/j.apsusc.2016.09.009 · Cited by 74
A spur gear mesh interface damping model based on elastohydrodynamic contact behaviour
Li, S., & Kahraman, A. (2011) · International Journal of Powertrains · doi:10.1504/ijpt.2011.041907 · Cited by 75
“On the other hand, gear EHL models were proposed to predict the gear mesh mechanical power losses mainly for efficiency prediction purposes (Li et al., 2009; Li and Kahraman, 2010b; Xu et al., 2007).”
MethodSelf-citationOptimisation of cylindrical gear pairs: A review
Miler, D., & Hoić, M. (2020) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2020.104156 · Cited by 71
Multi-objective optimal design of modification for helical gear
Wang, C. (2021) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2021.107762 · Cited by 71
Influence of Design Parameters on Mechanical Power Losses of Helical Gear Pairs
LI, S., VAIDYANATHAN, A., HARIANTO, J., & KAHRAMAN, A. (2009) · Journal of Advanced Mechanical Design, Systems, and Manufacturing · doi:10.1299/jamdsm.3.146 · Cited by 69
Self-citationTransmission efficiency of polyamide nanocomposite spur gears
Kirupasankar, S., Gurunathan, C., & Gnanamoorthy, R. (2012) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2012.02.045 · Cited by 67
Power flow and efficiency analysis of multi-flow planetary gear trains
Yang, F., Feng, J., & Zhang, H. (2015) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2015.05.003 · Cited by 67
Eckert, J. J., da Silva, S. F., Santiciolli, F. M., de Carvalho, Á. C., & Dedini, F. G. (2021) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2021.104644 · Cited by 63
Planetary gear sets power loss modeling: Application to wind turbines
Nutakor, C., Kłodowski, A., Sopanen, J., Mikkola, A., & Pedrero, J. I. (2016) · Tribology International · doi:10.1016/j.triboint.2016.09.029 · Cited by 67
An Experimental Investigation of the Efficiency of Planetary Gear Sets
Talbot, D. C., Kahraman, A., & Singh, A. (2012) · Journal of Mechanical Design · doi:10.1115/1.4005599 · Cited by 61
Self-citationA Windage Power Loss Model for Spur Gear Pairs
Seetharaman, S., & Kahraman, A. (2010) · Tribology Transactions · doi:10.1080/10402000903452848 · Cited by 57
Self-citationHelu, M., Vijayaraghavan, A., & Dornfeld, D. A. (2011) · CIRP Annals · doi:10.1016/j.cirp.2011.03.020 · Cited by 63
“Relationship between gear mesh efficiency, h, and RMS surface roughness, S, for different inlet lubricant temperatures, Toil, for a helical gear pair modeled after a final drive reduction [11].”
BackgroundInfluences of friction and mesh misalignment on time-varying mesh stiffness of helical gears
Han, L., Xu, L., & Qi, H. (2017) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-017-0602-6 · Cited by 54
Yue, K., Kang, Z., Zhang, M., Wang, L., Shao, Y., & Chen, Z. (2023) · Tribology International · doi:10.1016/j.triboint.2023.108378 · Cited by 58
An experimental investigation of spin power losses of a planetary gear set
Kahraman, A., Hilty, D. R., & Singh, A. K. (2014) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2014.12.003 · Cited by 53
Self-citationWang, S., & Zhu, R. (2020) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2020.105174 · Cited by 50
Novel calculation method for dynamic excitation of modified double-helical gear transmission
Yang, J., Lin, T., He, Z., et al. (2021) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2021.104467 · Cited by 47
A Method to Derive Friction and Rolling Power Loss Formulae for Mixed Elastohydrodynamic Lubrication
LI, S., & KAHRAMAN, A. (2011) · Journal of Advanced Mechanical Design, Systems, and Manufacturing · doi:10.1299/jamdsm.5.252 · Cited by 45
Self-citationDynamic modelling of gearbox with multiple localized defects and its coupled vibration analysis
Yu, Y., Shi, J., Shen, C., et al. (2022) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2022.109469 · Cited by 44
Simon, V. V. (2013) · Journal of Mechanical Design · doi:10.1115/1.4026264 · Cited by 43
Miao, Y., Rui, X., Wang, P., et al. (2023) · Applied Mathematical Modelling · doi:10.1016/j.apm.2023.09.027 · Cited by 42
Marques, P. M. T., Martins, R. C., & Seabra, J. (2016) · Tribology International · doi:10.1016/j.triboint.2016.02.002 · Cited by 40
Jiang, H., Shao, Y., Mechefske, C. K., et al. (2015) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-015-1001-5 · Cited by 40
Enhancement of wear resistance on normal contact ratio spur gear pairs through non-standard gears
Sekar, R. P., & Sathishkumar, R. (2017) · Wear · doi:10.1016/j.wear.2017.03.022 · Cited by 40
A novel prediction method for gear friction coefficients based on a computational inverse technique
Zhou, C., Hu, B., Qian, X., & Han, X. (2018) · Tribology International · doi:10.1016/j.triboint.2018.06.005 · Cited by 41
Study of Dynamic Model of Helical/Herringbone Planetary Gear System With Friction Excitation
Hou, S., Wei, J., Zhang, A., et al. (2018) · Journal of Computational and Nonlinear Dynamics · doi:10.1115/1.4041774 · Cited by 39
Liu, C., Qin, D., & Liao, Y. (2014) · Journal of Mechanical Design · doi:10.1115/1.4026572 · Cited by 39
Thermal-fluid-solid coupled dynamic modeling and validation for gear systems
Sun, Z., Tang, J., Chen, S., et al. (2025) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2025.110010 · Cited by 38
Wang, A. Z., & Kim, S. (2015) · Proceedings - IEEE International Conference on Robotics and Automation/Proceedings · doi:10.1109/icra.2015.7139307 · Cited by 38
“Experimental studies have tested on limited ratios, not enough to span the two gear ratios of a single pair of gears in step-up or step-down [17],[18],[19],[20],[21], [22].”
BackgroundDesign and power loss evaluation of a noncircular gear pair for an infinitely variable transmission
Li, G., & Zhu, W. D. (2020) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2020.104137 · Cited by 36
Chang, L., Jeng, Y., & Huang, P. (2012) · Journal of Tribology · doi:10.1115/1.4007809 · Cited by 36
“[6] presented an extensive literature summary of the modeling work and Petry-Johnson et al.”
BackgroundMethodA Transient Mixed Elastohydrodynamic Lubrication Model for Helical Gear Contacts
Chimanpure, A. S., Kahraman, A., & Talbot, D. C. (2020) · Journal of Tribology · doi:10.1115/1.4048499 · Cited by 35
Self-citationA novel approach for modeling the multiscale thermo-fluids of geared systems
Yazdani, M., & Soteriou, M. C. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.01.035 · Cited by 38
Moss, J., Kahraman, A., & Wink, C. H. (2018) · Journal of Tribology · doi:10.1115/1.4039929 · Cited by 38
Self-citationTorque loss in FZG-A10 gears lubricated with axle oils
Hammami, M., Fernandes, C. M. C. G., Martins, R. C., Abbès, M. S., Haddar, M., & Seabra, J. (2018) · Tribology International · doi:10.1016/j.triboint.2018.10.017 · Cited by 35
Analysis of efficiency of spur ground gears and the influence of running-in
Sjöberg, S., Sosa, M., Andersson, M., et al. (2015) · Tribology International · doi:10.1016/j.triboint.2015.08.045 · Cited by 35
Chen, J., Zhu, R., Chen, W., et al. (2022) · Nonlinear Dynamics · doi:10.1007/s11071-022-07872-y · Cited by 34
Partial EHL friction coefficient model to predict power losses in cylindrical gears
Arana, A., Larrañaga, J., & Ulacia, I. (2018) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650118778655 · Cited by 36
“One could, as an approximation, use two-slope viscosity– pressure models such as that suggested by Xu et al.(11) In addition, the type of equation used for the load sharing factor, , is a simple relationship allowing the extension of the fluid friction coefficient model to the partial EHL regime without computational…”
MethodMarques, P. M. T., Marafona, J. D. M., Martins, R. C., et al. (2021) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2021.104320 · Cited by 33
Chen, C., & Chen, J. (2015) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2014.12.017 · Cited by 33
“[13] introduced a prediction model, which accounts for load distribution and friction factors.”
BackgroundThe correlation between gear contact friction and ball on disc friction measurements
Björling, M., Miettinen, J., Marklund, P., Lehtovaara, A., & Larsson, R. (2014) · Tribology International · doi:10.1016/j.triboint.2014.11.007 · Cited by 32
“Such studies include both smooth [4, 5] and rough surfaces [6, 7, 8].”
BackgroundAnalysis of the Oil Squeezing Power Losses of a Spur Gear Pair by Mean of CFD Simulations
Concli, F., & Gorla, C. (2012) · ASME Biennial Conference on Engineering Systems Design and Analysis (ESDA) · doi:10.1115/esda2012-82591 · Cited by 37
Dynamic model of a helical gear pair considering tooth surface friction
Wang, C. (2020) · Journal of Vibration and Control · doi:10.1177/1077546319896124 · Cited by 32
“The results of this article fully conform to the conclusions of Xu et al. (2007).”
BackgroundResultInfluentialLi, Z., Chen, Z., & Zhai, W. (2022) · Nonlinear Dynamics · doi:10.1007/s11071-022-07963-w · Cited by 31
Prediction of the thermo-fluids of gearbox systems
Yazdani, M., Soteriou, M. C., Sun, F. P., & Chaudhry, Z. A. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.10.038 · Cited by 32
A Helical Gear Pair Pocketing Power Loss Model
Talbot, D. C., Kahraman, A., & Seetharaman, S. (2014) · Journal of Tribology · doi:10.1115/1.4026502 · Cited by 29
Self-citationA FBS-based energy modelling method for energy efficiency-oriented design
Li, L., Yu, S., Tao, J., et al. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.09.254 · Cited by 29
An experimental investigation of windage and oil churning power losses of gears and discs
Handschuh, M. J., Guner, A., & Kahraman, A. (2022) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501221104372 · Cited by 28
Self-citationParametric studies of spur gear lubrication performance considering dynamic loads
Liu, H., Mao, K., Zhu, C., et al. (2012) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650112445672 · Cited by 28
Influence of system-inherent phase in spur gear multi-state mesh based on nonlinear dynamics
Huang, Q., Tang, W., Lu, R., et al. (2022) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2021.108749 · Cited by 27
Hsu, C., & Huang, R.-H. (2008) · Journal of Mechanical Design · doi:10.1115/1.3013346 · Cited by 27
Talbot, D. C., Li, S., & Kahraman, A. (2013) · Journal of Mechanical Design · doi:10.1115/1.4025350 · Cited by 28
Self-citationEvolution of balanced root stress and tribological properties in high contact ratio spur gear drive
Ravivarman, R., Palaniradja, K., & Sekar, R. P. (2018) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2018.04.025 · Cited by 26
An Experimental Methodology to Determine Components of Power Losses of a Gearbox
Dindar, A., Chaudhury, K., Hong, I. J., Kahraman, A., & Wink, C. H. (2021) · Journal of Tribology · doi:10.1115/1.4049940 · Cited by 28
Self-citationA novel estimation method of friction coefficient for evaluating gear pitting fault
Wu, J., Yang, Y., & Cheng, J. (2021) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2021.105715 · Cited by 25
Zhang, Q., Wang, X., Wu, S., et al. (2022) · Nonlinear Dynamics · doi:10.1007/s11071-021-07092-w · Cited by 25
Dixit, Y., & Kulkarni, M. S. (2023) · Tribology International · doi:10.1016/j.triboint.2023.108284 · Cited by 28
Chen, Y., & Lin, Y. (2020) · Friction · doi:10.1007/s40544-020-0424-x · Cited by 24
Chen, S., Tan, R., Guo, X., et al. (2022) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2022.105028 · Cited by 24
High power density design for planetary gear transmission system
Wang, C. (2019) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406219850212 · Cited by 24
Enhanced friction model for high-speed right-angle gear dynamics
Feng, Z., Wang, S., Lim, T. C., & Peng, T. (2011) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-011-0803-3 · Cited by 23
“0.280.82Castrofα α= (7) 0.64 1.26 1.21 1 0.37 Zhufα α α = + (8) where min /Hα σ= is defined as the ratio of minimum film thickness lubricant minH to surface roughnessσ .”
BackgroundInfluentialNutakor, C., Montonen, J., Nerg, J. K., Heikkinen, J., Sopanen, J., & Pyrhonen, J. J. (2018) · Tribology International · doi:10.1016/j.triboint.2018.03.026 · Cited by 25
Sun, X., Wang, T., Zhang, R., et al. (2021) · Mathematics · doi:10.3390/math9030213 · Cited by 22
“μ(t) is the time-varying friction coefficient found in [25].”
BackgroundFace-gear drive: Meshing efficiency assessment
Zschippang, H. A., Weikert, S., & Wegener, K. (2022) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2022.104765 · Cited by 27
Efficiency and Durability Predictions of High Performance Racing Transmissions
Fatourehchi, E., Elisaus, V., Mohammadpour, M., Theodossiades, S., & Rahnejat, H. (2016) · SAE International Journal of Passenger Cars - Mechanical Systems · doi:10.4271/2016-01-1852 · Cited by 22
“[15] carried out a parametric studies using a numerical thermal EHL model to assess the effect of gear geometry, tooth modifications, operating conditions, lubricant properties, manufacturing and assembly errors, and surface finish on mechanical efficiency of gears.”
MethodA method for calculating gear meshing efficiency by measured data from gear test machine
Wang, C., Wang, S., & Wang, G. (2018) · Measurement · doi:10.1016/j.measurement.2018.01.031 · Cited by 22
Determination of load dependent gear loss factor on asymmetric spur gear
Sekar, R. P. (2019) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2019.02.011 · Cited by 22
Jiang, H., Liu, F., Zhang, J., et al. (2023) · International Journal of Non-Linear Mechanics · doi:10.1016/j.ijnonlinmec.2023.104583 · Cited by 20
Matsumoto, S., & MORIKAWA, K. (2014) · Elsevier eBooks · doi:10.1533/9781782421955.1078 · Cited by 19
A Novel Framework for Gear Safety Factor Prediction
Li, J., Liu, S., He, H., & Li, L. (2018) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2018.2868359 · Cited by 19
“4, for S , the pmf of D concentrates on the interval [1, 2], which is overlapped by the pmf of D .”
BackgroundTooth friction force and transmission error of spur gears due to sliding friction
Park, C. I. (2019) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-019-0232-2 · Cited by 19
Prediction Of Overall Efficiency In Multistage Gear Trains
Kuria, J., & Kihiu, J. M. (2011) · Zenodo (CERN European Organization for Nuclear Research) · doi:10.5281/zenodo.1076243 · Cited by 19
Electric Vehicle Energy Consumption Simulation by Modeling the Efficiency of Driveline Components
Tehrani, M. G., Kelkka, J., Sopanen, J., Mikkola, A., & Kerkkänen, K. S. (2016) · SAE International journal of commercial vehicles · doi:10.4271/2016-01-9016 · Cited by 18
Coefficient of friction of a starved lubricated spur gear pair
Liu, H., Zhu, C., Sun, Z., Zhang, Y., & Song, C. (2016) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-016-0424-y · Cited by 18
“proposed a model which combines a gear load distribution model, a friction coefficient model and a mechanical efficiency formulation to predict the instantaneous mechanical efficiency of a gear pair, and a friction coefficient formula was obtained through a multiple linear regression analysis [19].”
MethodAn experimental characterization of the friction coefficient of a wind turbine gearbox lubricant
Nutakor, C., Talbot, D. C., & Kahraman, A. (2019) · Wind Energy · doi:10.1002/we.2303 · Cited by 23
Self-citationInvestigating the efficiency of automotive manual gearboxes by experiment and simulation
Schaffner, T., Allmaier, H., Girstmair, J., et al. (2014) · Proceedings of the Institution of Mechanical Engineers Part K Journal of Multi-body Dynamics · doi:10.1177/1464419314539302 · Cited by 18
Xu, J., Jiao, C., Zou, D., et al. (2021) · Science China Technological Sciences · doi:10.1007/s11431-021-1916-x · Cited by 17
Influence of surface topography on the friction and dynamic characteristics of spur gears
Li, Z., Wang, J., Zhang, H., et al. (2020) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650119897471 · Cited by 17
“Xu et al.(25) predicted friction-related mechanical efficiency losses of parallel-axis gear pairs by combining TCA calculation results with EHL theory.”
MethodAnalytical and Experimental Investigation of Parameters Affecting Sliding Loss in a Spur Gear Pair
Yenti, C., Phongsupasamit, S., & Ratanasumawong, C. (2013) · Engineering Journal · doi:10.4186/ej.2013.17.1.79 · Cited by 17
Wang, S., & Zhu, R. (2022) · Journal of Tribology · doi:10.1115/1.4056351 · Cited by 16
Metadata
- Authors
- Xu, H., Kahraman, A., Anderson, N. E., & Maddock, D. G.
- Affiliations
- The Ohio State University (US)
- General Motors (United States) (US)
- Venue
- Journal of Mechanical Design
- Publisher
- ASME International
- Published
- 2006-06-14
- Volume
- 129
- Issue
- 1
- Pages
- 58-68
- ISSN
- 0161-8458 (ISSN-L)
- 1050-0472
- 1528-9001
- OpenAlex
- W1970036055
- Semantic Scholar
- e4f46f1dbb4c333508d9b97b58992c11dcdd3355
- Cited by
- 323
- References
- 40
- Citations by year
- 2026: 22 · 2025: 31 · 2024: 28 · 2023: 23 · 2022: 25 · 2021: 26 · 2020: 23 · 2019: 15 · 2018: 20 · 2017: 13 · 2016: 12 · 2015: 17 · 2014: 19 · 2013: 11 · 2012: 9
- FWCI
- 13.71
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Mechanical Design (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanics of Materials › Tribology and Wear Analysis
- Keywords
- parallel-axis gears, friction losses, gear load distribution, friction coefficient, elastohydrodynamic lubrication, non-Newtonian lubrication, tooth modification, lubricant properties, gear geometry
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.