The DOI matches its Crossref record; 9 of the 10 references it cites were found in a registry or an index; none of the 10 sources its claims cite is checked for support yet.
Characterization of MgSO4 Hydrate for Thermochemical Seasonal Heat Storage
Open accessAbstract
Water vapor sorption in salt hydrates is one of the most promising means for compact, low loss, and long-term storage of solar heat in the built environment. One of the most interesting salt hydrates for compact seasonal heat storage is magnesium sulfate heptahydrate (MgSO4⋅7H2O). This paper describes the characterization of MgSO4⋅7H2O to examine its suitability for application in a seasonal heat storage system for the built environment. Both charging (dehydration) and discharging (hydration) behaviors of the material were studied using thermogravimetric differential scanning calorimetry, X-ray diffraction, particle distribution measurements, and scanning electron microscope. The experimental results show that MgSO4⋅7H2O can be dehydrated at temperatures below 150°C, which can be reached by a medium temperature (vacuum tube) collector. Additionally, the material was able to store 2.2 GJ/m3, almost nine times more energy than can be stored in water as sensible heat. On the other hand, the experimental results indicate that the release of the stored heat is more difficult. The amount of water taken up and the energy released by the material turned out to be strongly dependent on the water vapor pressure, temperature, and the total system pressure. The results of this study indicate that the application of MgSO4⋅7H2O at atmospheric pressure is problematic for a heat storage system where heat is released above 40°C using a water vapor pressure of 1.3 kPa. However, first experiments performed in a closed system at low pressure indicate that a small amount of heat can be released at 50°C and a water vapor pressure of 1.3 kPa. If a heat storage system has to operate at atmospheric pressure, then the application of MgSO4⋅7H2O for seasonal heat storage is possible for space heating operating at 25°C and a water vapor pressure of 2.1 kPa.
Overview
CoChat Summary
TL;DR
MgSO₄·7H₂O is characterized for seasonal thermochemical heat storage; it dehydrates below 150°C and its second dehydration step stores 2.2 GJ/m³, almost nine times water sensible heat. However, heat release is strongly limited by water vapor pressure and temperature, and atmospheric-pressure hydration is problematic for practical conditions above 40°C, though a low-pressure fixed-bed test showed a 4°C temperature lift.
Key findings
- Dehydration proceeds in at least three steps: first at 25–55°C with 6.9±0.2% mass loss (one H₂O); second at 60–265°C with 42.2±0.3% mass loss (5.9 H₂O) and an energy density of 2.2±0.1 GJ/m³, almost nine times water sensible heat (0.25 GJ/m³, 25–85°C); third near 275°C with 0.5±0.1% mass loss (0.1 H₂O). The second step is most interesting because it occurs below 150°C and avoids melting problems.
- Hydration at 25°C and 1 atm depends strongly on water vapor pressure: increasing P_H₂O from 1.3 kPa to 2.1 kPa raises uptake from one to six water molecules per MgSO₄. The single-step MgSO₄→MgSO₄·6H₂O hydration has an energy density of 1.8±0.1 GJ/m³, about 88% of the corresponding dehydration energy density (2.1±0.1 GJ/m³); at 1.3 kPa only 15% of stored energy is released (44.7 kJ/mol instead of 303 kJ/mol).
- At 50°C and P_H₂O=2.1 kPa, MgSO₄ is unable to take up water; under practical conditions (P_H₂O=1.3 kPa and T>40°C), the material cannot take up water at atmospheric pressure. A closed fixed-bed reactor at low pressure (evacuated to 2.8 mbar, reactor at 50°C, evaporator at 10°C, P_H₂O sat=1.3 kPa) showed a maximum temperature increase of 4°C, indicating a small amount of heat can be released.
- Melting occurs at 52.5°C, in good agreement with 50°C from Emons et al., and can reduce bed porosity and vapor transport; it was avoided with heating rates ≤1°C/min, particles <200 µm, and/or sample sizes ≤5 mg, which the paper notes will be difficult to meet in a large heat storage system. Particle size distribution had limited effect on hydration for the studied ranges, but layer thickness strongly affected hydration rate, indicating vapor transport through the layer is limiting.
Methods
- Reagent-grade MgSO₄·7H₂O (99.5% pure) was sieved into 20–38, 38–106, 106–200, and 200–500 µm fractions; unless stated otherwise, 38–106 µm particles were used. Thermal analysis used TG-DSC at ECN and Netzsch with Netzsch STA 409 PC Luxx and DSC 204 F1 Phoenix apparatus, nitrogen-water vapor flows, sample masses of 5–50 mg (standard 10 mg), and atmospheric pressure; hydration/dehydration were studied at 25°C and 50°C with P_H₂O of 1.3, 2.1, and 2.3 kPa.
- X-ray diffraction used a Bruker D8 Advance with MRI oven, Cu Kα1+α2=1.5418 Å, 2θ from 10° to 40°, 0.05° steps, 2 s per step; 150 mg samples were dehydrated from 25°C to 300°C at 1°C/min and hydrated at 25°C. SEM used a JEOL JSM 6330F with platinum-coated samples at 5–15 kV and 50–1500× magnification; particle size distribution used a Malvern Master 2000 laser diffraction instrument with MgSO₄-ethanol suspension and ultrasound.
- A fixed-bed reactor test used a 98 ml storage volume, 25 g MgSO₄·7H₂O dehydrated at 150°C, connected to an evaporator at 10°C and a vacuum pump system; the system was evacuated to 2.8 mbar, the reactor was held at 50°C, and thermocouples monitored temperature during hydration.
Limitations
- The paper states that the local water vapor pressure near the sample at ECN was not determined; possible incomplete gas mixing led the authors to assume 2.3 kPa instead of 1.3 kPa, and more experiments are required to verify this. It also states that the second dehydration step could not be clearly resolved into individual steps, the MgSO₄·2H₂O intermediate was not confirmed by XRD, and more research is needed to understand particle size behavior and the low-pressure process and actual energy released.
- The paper states that atmospheric-pressure application is problematic for heat release above 40°C at P_H₂O=1.3 kPa, and at 50°C and 2.1 kPa no water uptake occurred. The low-pressure fixed-bed result is described as an initial test with only a 4°C temperature lift, and the actual amount of energy released was not determined.
- Evident from the text: thermal analysis used small samples (5–50 mg, standard 10 mg) and the fixed-bed test used 25 g, so scale-up to a large storage system is not demonstrated; the melting-avoidance criteria (≤1°C/min, <200 µm, ≤5 mg) are noted as difficult to meet in large quantities. The ECN versus Netzsch discrepancy also indicates measurement/atmosphere uncertainty.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 0 Not valid · 12 Not checked · 84 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the reaction primarily occurs in a temperature range that can be covered by medium temperature collectors ͑Յ150° C͒”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The effect of increasing the temperature from 25° C ͑curve 2 in Fig. 4͒ to 50° C at constant water vapor pressure of 2.1 kPa is evident: MgSO 4 is unable to take up water at 50° C.”
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“However, first experiments performed in a closed system at low pressure indicate that a small amount of heat can be released at 50° C and a water vapor pressure of 1.3 kPa.”
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The results show that the dehydration of MgSO 4 •7H 2 O proceeds in at least three steps”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Hydration experiments performed at atmospheric pressure reveal that the amount of water taken up by MgSO 4 depends on partial water vapor pressure and the temperature.”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
57 more claims
Create a free account to see all 96 claims and to verify the 7 references still open.
- It may state two separate claims as one. 28
- Probably not a substantial claim. 8
Citations
Cites
Ullmann's Encyclopedia of Industrial Chemistry
(2012) · Choice Reviews Online · doi:10.5860/choice.50-1224 · Cited by 3,049
A Fundamental Equation of State for Heavy Water
Hill, P. G., MacMillan, R. D. C., & Lee, V. (1982) · Journal of Physical and Chemical Reference Data · doi:10.1063/1.555661 · Cited by 1,503
(1982) · Medical Entomology and Zoology · Cited by 1,294
Introduction to Thermal Analysis
Brown, M. E. (1988) · Springer eBooks · doi:10.1007/978-94-009-1219-9 · Cited by 685
Experimental stability of magnesium sulfate hydrates that may be present on Mars
Chipera, S. J., & Vaniman, D. T. (2007) · Geochimica et Cosmochimica Acta · doi:10.1016/j.gca.2006.07.044 · Cited by 175
Ruiz-Agudo, E., Martín-Ramos, J. D., & Rodriguez-Navarro, C. (2007) · The Journal of Physical Chemistry B · doi:10.1021/jp064460b · Cited by 59
Emons, H. H., Ziegenbalg, G., Naumann, R., & Paulik, F. (1990) · Journal of Thermal Analysis · doi:10.1007/bf01914050 · Cited by 37
First studies in reactor concepts for Thermochemical Storage
Schuitema, R., van Helden, W. G. J., Zondag, H. A., Krosse, L., van Essen, V. M., Bleijendaal, L. P. J., & Kalbasenka, A. N. (2009) · TNO Repository · Cited by 37
Self-citationCompacte chemische seizoenopslag van zonnewarmte Eindrapportage
. (2004) · TNO Repository
Cited by
Sorption thermal storage for solar energy
Yu, N., Wang, R. Z., & Wang, L. W. (2013) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2013.05.004 · Cited by 589
The latest advancements on thermochemical heat storage systems
Aydin, D., Casey, S. P., & Riffat, S. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.08.054 · Cited by 576
Adsorption-Driven Heat Pumps: The Potential of Metal–Organic Frameworks
de Lange, M. F., Verouden, K. J. F. M., Vlugt, T. J. H., Gascon, J., & Kapteijn, F. (2015) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00059 · Cited by 510
Lizana, J., Chacartegui, R., Barrios-Padura, A., & Valverde, J. M. (2017) · Applied Energy · doi:10.1016/j.apenergy.2017.06.008 · Cited by 410
A review of salt hydrates for seasonal heat storage in domestic applications
Donkers, P. A. J., Sögütoglu, L. C., Huinink, H. P., Fischer, H. R., & Adan, O. C. G. (2017) · Applied Energy · doi:10.1016/j.apenergy.2017.04.080 · Cited by 403
Metadata
- Authors
- van Essen, V. M., Zondag, H. A., Gores, J. C., Bleijendaal, L. P. J., Bakker, M., Schuitema, R., van Helden, W. G. J., He, Z., & Rindt, C. C. M.
- Affiliations
- Energy Research Centre of the Netherlands (NL)
- Eindhoven University of Technology (NL)
- Venue
- Journal of Solar Energy Engineering
- Publisher
- ASME International
- Published
- 2009-10-16
- Volume
- 131
- Issue
- 4
- ISSN
- 0199-6231 (ISSN-L)
- 1528-8986
- OpenAlex
- W2128670854
- Semantic Scholar
- 731a71a431ee100c16e7dfdba7e999ad1d3a0920
- Cited by
- 291
- References
- 10
- Citations by year
- 2026: 18 · 2025: 26 · 2024: 16 · 2023: 18 · 2022: 25 · 2021: 13 · 2020: 29 · 2019: 24 · 2018: 26 · 2017: 25 · 2016: 16 · 2015: 13 · 2014: 17 · 2013: 11 · 2012: 8
- FWCI
- 9.47
- Type
- journal article
- Language
- en
- Open access
- green
- resolver.tno.nl
- Locations
- Journal of Solar Energy Engineering (publishedVersion)
- TNO Repository (submittedVersion)
- TU/e Research Portal (submittedVersion)
- Repository hosted by TU Delft Library (TU Delft) (submittedVersion)
- Data Archiving and Networked Services (DANS) (submittedVersion, other-oa)
- Funders
- Technische Universiteit Eindhoven
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Physical Sciences › Engineering › Mechanical Engineering › Phase Change Materials Research
- Physical Sciences › Energy › Fuel Technology › Chemical Looping and Thermochemical Processes
- Keywords
- magnesium sulfate heptahydrate, salt hydrates, thermochemical energy storage, seasonal thermal energy storage, solar thermal energy storage, water vapor adsorption, hydration and dehydration, water vapor pressure, heat storage density, space heating
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-11-16, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-11-16 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Characterization of MgSO4 Hydrate for Thermochemical Seasonal Heat Storage. https://app.cochat.ai/papers/10.1115/1.4000275
- The paper
- van Essen, V. M., Zondag, H. A., Gores, J. C., Bleijendaal, L. P. J., Bakker, M., Schuitema, R., van Helden, W. G. J., He, Z., & Rindt, C. C. M. (2009). Characterization of MgSO4 Hydrate for Thermochemical Seasonal Heat Storage. Journal of Solar Energy Engineering. https://doi.org/10.1115/1.4000275
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.