CoChat

Level Set Topology Optimization of Printed Active Composites

Open access
Maute, Kurt, Tkachuk, Anton, Wu, Jiangtao, Jerry Qi, H., Ding, Zhen, Dunn, Martin L. · 2015 · Journal of Mechanical Design
Cited by 101

The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.

Abstract

Multimaterial polymer printers allow the placement of different material phases within a composite, where some or all of the materials may exhibit an active response. Utilizing the shape memory (SM) behavior of at least one of the material phases, active composites can be three-dimensional (3D) printed such that they deform from an initially flat plate into a curved structure. This paper introduces a topology optimization approach for finding the spatial arrangement of shape memory polymers (SMPs) within a passive matrix such that the composite assumes a target shape. The optimization approach combines a level set method (LSM) for describing the material layout and a generalized formulation of the extended finite-element method (XFEM) for predicting the response of the printed active composite (PAC). This combination of methods yields optimization results that can be directly printed without the need for additional postprocessing steps. Two multiphysics PAC models are introduced to describe the response of the composite. The models differ in the level of accuracy in approximating the residual strains generated by a thermomechanical programing process. Comparing XFEM predictions of the two PAC models against experimental results suggests that the models are sufficiently accurate for design purposes. The proposed optimization method is studied with examples where the target shapes correspond to a plate-bending type deformation and to a localized deformation. The optimized designs are 3D printed and the XFEM predictions are compared against experimental measurements. The design studies demonstrate the ability of the proposed optimization method to yield a crisp and highly resolved description of the optimized material layout that can be realized by 3D printing. As the complexity of the target shape increases, the optimal spatial arrangement of the material phases becomes less intuitive, highlighting the advantages of the proposed optimization method.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1115/1.4030994

Cites

2 of 2 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 2 references

Research works printed but not linked: 26

  1. 2014, Advanced Shape Memory Technology to Reshape Product Design, Manufacturing and Recycling, Polymers, 6, 2287, 10.3390/polym6082287 · DOI · Paper page
  2. 2014, Active Origami by 4D Printing, Smart Mater. Struct., 23, 094007, 10.1088/0964-1726/23/9/094007 · DOI · Paper page
  3. 2010, Shape-Memory Polymers and Shape-Changing Polymers, 1
  4. 2010, Thermally Actuated Shape-Memory Polymers: Experiments, Theory, and Numerical Simulations, J. Mech. Phys. Solids, 58, 1100, 10.1016/j.jmps.2010.04.004 · DOI · Paper page
  5. 2014, Reduced Time as a Unified Parameter Determining Fixity and Free Recovery of Shape Memory Polymers, Nat. Commun., 5, 3066, 10.1038/ncomms4066 · DOI · Paper page
  6. 1989, Optimal Shape Design as a Material Distribution Problem, Struct. Multidiscip. Optim., 1, 193, 10.1007/BF01650949 · DOI · Paper page
  7. 1991, The COC Algorithm, Part II: Topological, Geometrical and Generalized Shape Optimization, Comput. Methods Appl. Mech. Eng., 89, 309, 10.1016/0045-7825(91)90046-9 · DOI
  8. 2014, A Survey of Structural and Multidisciplinary Continuum Topology Optimization: Post 2000, Struct. Multidiscip. Optim., 49, 1, 10.1007/s00158-013-0956-z · DOI · Paper page
  9. 2013, Level-Set Methods for Structural Topology Optimization: A Review, Struct. Multidiscip. Optim., 48, 437, 10.1007/s00158-013-0912-y · DOI · Paper page
  10. 2010, The Extended/Generalized Finite Element Method: An Overview of the Method and Its Applications, Int. J. Numer. Methods Eng., 84, 253, 10.1002/nme.2914 · doi:10.1002/nme.2914
  11. 2012, Levelset Based Fluid Topology Optimization Using the Extended Finite Element Method, Struct. Multidiscip. Optim., 46, 311, 10.1007/s00158-012-0782-8 · DOI
  12. 2014, Numerical Instabilities in Level Set Topology Optimization With the Extended Finite Element Method, Struct. Multidiscip. Optim., 49, 185, 10.1007/s00158-013-0982-x · DOI
  13. 2014, Density and Level Set-XFEM Schemes for Topology Optimization of 3-D Structures, Comput. Mech., 54, 133, 10.1007/s00466-014-1027-z · DOI
  14. 2008, A Thermoviscoelastic Model for Amorphous Shape Memory Polymers: Incorporating Structural and Stress Relaxation, J. Mech. Phys. Solids, 56, 2792, 10.1016/j.jmps.2008.04.007 · DOI · Paper page
  15. 2008, Finite Deformation Thermo-Mechanical Behavior of Thermally Induced Shape Memory Polymers, J. Mech. Phys. Solids, 56, 1730, 10.1016/j.jmps.2007.12.002 · DOI · Paper page
  16. Stiltner, L. J., Elliott, A. M., and Williams, C. B., 2011, “A Method for Creating Actuated Joints Via Fiber Embedding in a Polyjet 3D Printing Process,” International Solid Freeform Fabrication Symposium, Vol. 22, pp. 583–592.
  17. 2015, Level Set Topology Optimization of Scalar Transport Problems, Struct. Multidiscip. Optim., 51, 267, 10.1007/s00158-014-1142-7 · DOI
  18. 1999, On the Topological Derivative in Shape Optimization, SIAM J. Control Optim., 37, 1251, 10.1137/S0363012997323230 · DOI
  19. 2005, Structural Optimization Using Topological and Shape Sensitivity Via a Level Set Method, Control Cybern., 34, 59
  20. 2007, A Topological Derivative Method for Topology Optimization, Struct. Multidiscip. Optim., 33, 375, 10.1007/s00158-007-0094-6 · DOI
  21. 2004, A Finite Element Method for the Simulation of Strong and Weak Discontinuities in Solid Mechanics, Comput. Methods Appl. Mech. Eng., 193, 3523, 10.1016/j.cma.2003.12.041 · doi:10.1016/j.cma.2003.12.041
  22. 2003, Finite Cover Method for Linear and Non-Linear Analyses of Heterogeneous Solids, Int. J. Numer. Methods Eng., 58, 1321, 10.1002/nme.820 · doi:10.1002/nme.820
  23. 2011, A Multiple Level Set Approach to Prevent Numerical Artefacts in Complex Microstructures With Nearby Inclusions Within XFEM, Int. J. Numer. Methods Eng., 85, 1436, 10.1002/nme.3025 · doi:10.1002/nme.3025
  24. 2014, A Simple and Efficient Preconditioning Scheme for XFEM With Heaviside Enrichments, Comput. Mech., 54, 1357, 10.1007/s00466-014-1063-8 · doi:10.1007/s00466-014-1063-8
  25. 1986, gmres: A Generalized Minimal Residual Algorithm for Solving Nonsymmetric Linear Systems, SIAM J. Sci. Stat. Comput., 7, 856, 10.1137/0907058 · DOI · Paper page
  26. 2002, A Class of Globally Convergent Optimization Methods Based on Conservative Convex Separable Approximations, SIAM J. Optim., 12, 555, 10.1137/S1052623499362822 · DOI · Paper page

Cited by

See all 101

Metadata

Authors
Maute, K., Tkachuk, A., Wu, J., Jerry Qi, H., Ding, Z., & Dunn, M. L.
Venue
Journal of Mechanical Design
Published
2015-10-12
Volume
137
Issue
11
ISSN
  • 0161-8458 (ISSN-L)
  • 1050-0472
  • 1528-9001
OpenAlex
W2097925802
Cited by
101
References
2
FWCI
13.21
Type
journal article
Language
en
Open access
bronze

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Level Set Topology Optimization of Printed Active Composites. https://app.cochat.ai/papers/10.1115/1.4030994
The paper
Maute, K., Tkachuk, A., Wu, J., Jerry Qi, H., Ding, Z., & Dunn, M. L. (2015). Level Set Topology Optimization of Printed Active Composites. Journal of Mechanical Design. https://doi.org/10.1115/1.4030994

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.