CoChat

Polyethylene materials with in-chain ketones from nonalternating catalytic copolymerization

Open access

Published version of a preprint

The DOI matches its Crossref record; 47 of the 47 references it cites were found in a registry or an index; 1 of the 8 sources its claims cite were checked for support.

Abstract

Polyethylene with a nickel’s worth of CO: The biggest problem with polyethylene, the most abundantly manufactured plastic, is that it doesn’t break down easily once it is discarded. Chemists have long sought to introduce small quantities of carbon monoxide (CO) into polyethylene chains to promote photodegradation, but too much CO tends to jump in and spoil the plastic’s other properties. Baur et al . report that nickel catalysts coordinated by bulky phosphinophenolate ligands can catalyze ethylene polymerization with approximately 1% CO incorporation, preserving tensile strength while promoting degradation under ultraviolet exposure (see the Perspective by Sobkowicz). —JSY

Overview

CoChat Summary

TL;DR

Neutral Ni(II) phosphinophenolate catalysts enable non-alternating copolymerization of ethylene and CO, placing isolated in-chain keto groups into high molecular weight polyethylene while retaining HDPE-like crystallinity and tensile properties. The resulting keto-modified polyethylenes are melt-processable and may offer a route to less environmentally persistent polyolefins.

Key findings

  • Non-alternating ethylene/CO copolymerization was achieved with Ni(II) catalysts 2–7; at low CO incorporation, keto groups are mostly isolated or non-alternating rather than alternating. For example, entry 4 gave 0.3 mol% CO incorporation, I/NA/A = 79/21/0, Mn = 140 × 10³ g mol⁻¹, Mw/Mn = 1.6, and Tm = 134 °C (68% crystallinity); entry 10 gave 0.6 mol% CO by IR (1.4 mol% by ¹³C NMR), I/NA/A = 27/33/39, Mn = 154 × 10³ g mol⁻¹, and Tm = 134 °C.
  • The keto-modified polyethylenes reached high molecular weights up to Mw ~400,000 g mol⁻¹ and Mn ~220,000 g mol⁻¹, in contrast to prior ethylene–CO copolymerizations that yielded low molecular weight brittle waxes with Mn ≤ 3,000 g mol⁻¹.
  • HDPE materials properties were retained: WAXS diffractograms were virtually identical to HDPE, melting/crystallization points were virtually unaltered, and injection-molded test bars showed ductile tensile behavior comparable to commercial HDPE. Reported tensile values were E = 995 MPa and σy = 29 MPa, compared with literature HDPE E = 900 MPa and σy = 27 MPa, and LDPE E = 240 MPa and σy = 12 MPa.
  • CO appeared to suppress chain transfer and branching: endgroup analysis showed only olefinic endgroups also found in homopolyethylenes, and copolymers showed complete absence of branches compared with ethylene homopolymers; catalysts were stable for hours in CO copolymerizations.

Methods

  • Polymerization experiments screened neutral Ni(II) catalyst precursors: salicylaldiminato 1 and phosphinophenolato complexes 2–8 with bulky substituents. Table 1 conditions were typically 10 µmol precatalyst, 100 mL toluene, 500 rpm, 50–120 °C, 5–40 bar ethylene, CO in feed 0.2–2.6 mol%, and 10–240 min; selected entries used 5 µmol precatalyst, 200 mL toluene, and 0.05 atm CO introduced before ethylene.
  • Microstructure was analyzed by ¹³C NMR using ¹³CO copolymers, with 1D and 2D NMR and IR spectroscopy; CO incorporation was determined by IR and by ¹³C NMR. Molecular weights were measured by GPC in 1,2-dichlorobenzene at 160 °C via universal calibration against polystyrene standards; thermal data by DSC second heating; solid-state structure by WAXS; mechanical properties by tensile tests on injection-molded bars.
  • Mechanistic features were probed by comparing polymer composition and yield over time, comparing copolymerization with ethylene homopolymerization, and analyzing polymer endgroups.

Limitations

  • The paper does not include a dedicated Limitations section. Stated limitations include: copolymerization yields and average activities were lowered compared with ethylene homopolymerization; efficient copolymerization with catalyst 2 required ca. 100 °C; higher polymerization temperatures decreased CO incorporation and were necessary to achieve non-alternation; catalyst 1 had limited temperature stability and formed only alternating polyketone even at elevated temperature.
  • Evident from the data: non-alternating products were obtained only at high E/CO ratios on the order of 100 and generally low CO feed (many useful entries at 0.2–0.6 mol% CO in feed); higher CO feed often gave alternating polyketone or very low yields. Several catalyst precursors (e.g., 1, 3, 4, 6, 8 under tested conditions) gave alternating polyketone or negligible activity.
  • The paper presents perspectives for photolytic and oxidative chain breakdown but does not report degradation or long-term environmental persistence data for these specific materials.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1126/science.abi8183

Cites

47 of 47 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Fig. 1 Catalyst precursors studied. Salicylaldiminato complex 1 , and phosphinephenolato complexes 2 to 8 .
Fig. 1 Catalyst precursors studied. Salicylaldiminato complex 1 , and phosphinephenolato complexes 2 to 8 .CC-BY-NC-ND · From the PDF
Fig. 2 Microstructure Characterization of Copolymers. a, Carbonyl regime of 13 C NMR spectra of 13 CO copolymers with different keto contents (C2 D2Cl4 solvent, 383 K) and an alternating polyketone (hexafluoroisopropanol/C6D6 solvent, 273 K) for comparison. IC: Isolated carbonyl, DCX: Double carbonyl separated by X repeat units of ethylene, APK: Alternating polyketone, *: Carbonyl adjacent to an alternating sequence b, IR spectra of copolymers with different keto contents, and alternating polyketone for comparison. The absorbance intensity of alternating polyketone is adjusted for clarity. Note these are 13 CO copolymers as in a, which shifts the absorption frequency compared to non-labelled copolymers (cf. the Supporting Information for IR spectra of the latter).
Fig. 2 Microstructure Characterization of Copolymers. a, Carbonyl regime of 13 C NMR spectra of 13 CO copolymers with different keto contents (C2 D2Cl4 solvent, 383 K) and an alternating polyketone (hexafluoroisopropanol/C6D6 solvent, 273 K) for comparison. IC: Isolated carbonyl, DCX: Double carbonyl separated by X repeat units of ethylene, APK: Alternating polyketone, *: Carbonyl adjacent to an alternating sequence b, IR spectra of copolymers with different keto contents, and alternating polyketone for comparison. The absorbance intensity of alternating polyketone is adjusted for clarity. Note these are 13 CO copolymers as in a, which shifts the absorption frequency compared to non-labelled copolymers (cf. the Supporting Information for IR spectra of the latter).CC-BY-NC-ND · From the PDF
Fig. 3 Materials Characterization of Copolymers. a, WAXS of copolymers with different keto contents and commercial HDPE. Reflexes correspond to the orthorhombic unit cell of polyethylene. b, GPC trace of copolymer (1.0 mol% keto repeat units), and commercial HDPE for comparison. c, DSC trace of copolymer (0.8 mol% keto repeat units), and commercial HDPE for comparison. d, Representative stressstrain curves of injection molded keto-modified polyethylene (0.6 mol% keto repeat units) in comparison to commercial HDPE.
Fig. 3 Materials Characterization of Copolymers. a, WAXS of copolymers with different keto contents and commercial HDPE. Reflexes correspond to the orthorhombic unit cell of polyethylene. b, GPC trace of copolymer (1.0 mol% keto repeat units), and commercial HDPE for comparison. c, DSC trace of copolymer (0.8 mol% keto repeat units), and commercial HDPE for comparison. d, Representative stressstrain curves of injection molded keto-modified polyethylene (0.6 mol% keto repeat units) in comparison to commercial HDPE.CC-BY-NC-ND · From the PDF

Verification

Claims the paper makes

0 Valid · 2 Not valid · 5 Not checked · 28 Own results and interpretations

13 more claims

Create a free account to see all 35 claims and every source verdict.

See all claims — free account
  • It may state two separate claims as one. 16
  • Probably not a substantial claim. 2

Create a free account to see these claims.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

1 of 1

Citations

Cites

Show all 47 references

Research works printed but not linked: 2

  1. Press release by Hyosung of May 5 2016: Hyosung introduces the polyketone brand ‘POKETONE™’ to the global market (retrieved June 8 2021 from www.poketone.com).
  2. C. E. Ash, D. G. Waters, A. A. Smaardijk, Soc. Plast. Eng. 53, 2319 (1995).

Cited by

See all 287

Metadata

Authors
Baur, M., Lin, F., Morgen, T. O., Odenwald, L., & Mecking, S.
Affiliations
University of Konstanz (DE)
Corresponding author
Mecking, Stefan
Venue
Science
Published
2021-10-29
Volume
374
Issue
6567
Pages
604-607
ISSN
  • 0036-8075 (ISSN-L)
  • 1095-9203
OpenAlex
W3211073624
Cited by
287
References
46
Citations by year
2026: 60 · 2025: 72 · 2024: 65 · 2023: 40 · 2022: 42 · 2021: 8
FWCI
14.88
Type
journal article
Language
en
Open access
Licence
cc-by-nc-nd
Locations
  • Science (publishedVersion)
  • ChemRxiv (submittedVersion, cc-by-nc-nd)
  • PubMed (publishedVersion)
  • Figshare (submittedVersion, cc-by-nc-nd)
  • KOPS (University of Konstanz) (submittedVersion)
Funders
H2020 European Research Council (832480)
Topics
  • Physical Sciences › Chemistry › Organic Chemistry › Organometallic Complex Synthesis and Catalysis
  • Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
  • Physical Sciences › Chemistry › Organic Chemistry › Advanced Polymer Synthesis and Characterization
Keywords
polyethylene, high-density polyethylene, tensile properties, injection molding

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-12, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-12 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Polyethylene materials with in-chain ketones from nonalternating catalytic copolymerization. https://app.cochat.ai/papers/10.1126/science.abi8183
The paper
Baur, M., Lin, F., Morgen, T. O., Odenwald, L., & Mecking, S. (2021). Polyethylene materials with in-chain ketones from nonalternating catalytic copolymerization. Science. https://doi.org/10.1126/science.abi8183

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.