Mechanical Properties and Morphological Characterization of PLA/Chitosan/Epoxidized Natural Rubber Composites
Open accessThe DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.
Abstract
Poly (lactic acid) (PLA)/chitosan (CS) natural polymer/epoxidised natural rubber (ENR) composites were successfully prepared through a solution casting method. The morphological characteristics of fabricated composites were investigated by scanning electron microscopy (SEM) and optical microscopy. The microstructure of PLA/ENR was significantly altered with the addition of CS. SEM analysis of composites fractured surfaces revealed smooth and homogeneous texture and good dispersion of CS. However for 15 wt% CS composites, the phase segregation and poor adhesion between the polymers were observed. Fourier transform infrared spectroscopy revealed some levels of attractive interaction between CS, PLA, and ENR in the composites. The mechanical properties of composites in terms of tensile strength and tensile modulus were significantly improved with the addition of CS into the matrix while the percent elongation at break decreased. The tensile strength increased up to 5 wt% CS loading for both PLA/CS and PLA/ENR/CS and thereafter decreased while Young’s modulus increased up to 10 wt%. However, when the CS content was increased to 15 wt%, the tensile strength and tensile modulus were slightly decreased. These improvements were attributed to good dispersion of CS at the optimum filler levels and attractive interaction between the composites components.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Electrospinning of Nanofibers: Reinventing the Wheel?
Li, D., & Xia, Y. (2004) · Advanced Materials · doi:10.1002/adma.200400719 · Cited by 5,521
Chitosan Chemistry and Pharmaceutical Perspectives
Kumar, M. N. V. R., Muzzarelli, R. A. A., Muzzarelli, C., Sashiwa, H., & Domb, A. J. (2004) · Chemical Reviews · doi:10.1021/cr030441b · Cited by 2,938
Review: current international research into cellulose nanofibres and nanocomposites
Eichhorn, S. J., Dufresne, A., Aranguren, M., Marcovich, N. E., Capadona, J. R., Rowan, S. J., Weder, C., Thielemans, W., Roman, M., Renneckar, S., et al. (2010) · Journal of Materials Science · doi:10.1007/s10853-009-3874-0 · Cited by 2,418
Chitins and chitosans for the repair of wounded skin, nerve, cartilage and bone
Muzzarelli, R. A. A. (2009) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2008.11.002 · Cited by 1,103
Novel chitin and chitosan nanofibers in biomedical applications
Jayakumar, R., Prabaharan, M., Nair, S. V., & Tamura, H. (2010) · Biotechnology Advances · doi:10.1016/j.biotechadv.2009.11.001 · Cited by 1,013 · cited 1×
“CS was used to create edible coatings or films to extend foodstuffs’ shelf life, such as fruits, meat, fish, and seafood [15, 16].”
MethodJonoobi, M., Harun, J., Mathew, A. P., & Oksman, K. (2010) · Composites Science and Technology · doi:10.1016/j.compscitech.2010.07.005 · Cited by 863
Mathew, A. P., Oksman, K., & Sain, M. (2005) · Journal of Applied Polymer Science · doi:10.1002/app.21779 · Cited by 851
Manufacturing process of cellulose whiskers/polylactic acid nanocomposites
Oksman, K., Mathew, A. P., Bondeson, D., & Kvien, I. (2006) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.03.002 · Cited by 783
Structure and thermal properties of poly(lactic acid)/cellulose whiskers nanocomposite materials
Petersson, L., Kvien, I., & Oksman, K. (2007) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.12.012 · Cited by 576
Pei, A., Zhou, Q., & Berglund, L. A. (2010) · Composites Science and Technology · doi:10.1016/j.compscitech.2010.01.018 · Cited by 524
Research works printed but not linked: 3
- 2012, Bioresources, 7, 5568
- 2012, Journal of Thermoplastic Composite Materials, 26, 1
- 10.1002/adma.200400719 · DOI · Paper page
Cited by
Farah, S., Anderson, D. G., & Langer, R. (2016) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.06.012 · Cited by 3,443
Poly (lactic acid) blends: Processing, properties and applications
Nofar, M., Sacligil, D., Carreau, P. J., Kamal, M. R., & Heuzey, M.-C. (2019) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2018.12.002 · Cited by 780
Ilyas, R., Aisyah, H., Nordin, A., Ngadi, N., Zuhri, M., Asyraf, M., Sapuan, S., Zainudin, E., Sharma, S., Abral, H., et al. (2022) · Polymers · doi:10.3390/polym14050874 · Cited by 258
Habiba, U., Siddique, T. A., Joo, T. C., Salleh, A., Ang, B. C., & Afifi, A. M. (2017) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.11.037 · Cited by 243
Materials for food packaging applications based on bio-based polymer nanocomposites: A review
Attaran, S. A., Hassan, A., & Wahit, M. U. (2017) · Journal of Thermoplastic Composite Materials · doi:10.1177/0892705715588801 · Cited by 170
Self-citationWang, Y., Chen, K., Xu, C., & Chen, Y. (2015) · The Journal of Physical Chemistry B · doi:10.1021/acs.jpcb.5b06244 · Cited by 145
Habiba, U., Islam, M. S., Siddique, T. A., Afifi, A. M., & Ang, B. C. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.04.127 · Cited by 127
Self-citationRojas, A., Velásquez, E., Vidal, C. P., Guarda, A., Galotto, M. J., & de Dicastillo, C. L. (2021) · Antioxidants · doi:10.3390/antiox10121976 · Cited by 111
Mechanical properties of PLA-based composites for fused deposition modeling technology
Lebedev, S. M., Gefle, O. S., Amitov, E. T., Zhuravlev, D. V., Berchuk, D. Y., & Mikutskiy, E. A. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-1953-6 · Cited by 86
“based composites compared with PLA matrix can be caused by the restriction of the polymer chain mobility and deformability due to the presence of filler particles [12, 13].”
BackgroundVasile, C., Stoleru, E., Darie-Niță, R. N., Dumitriu, R. P., Pamfil, D., & Mititelu-Tarțău, L. (2019) · Polymers · doi:10.3390/polym11060941 · Cited by 75
“Similar results were found by other authors [104].”
ResultSingh, A. A., Sharma, S., Srivastava, M., & Majumdar, A. (2019) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2019.10.246 · Cited by 74
Görgün, E., Ali, A., & Islam, M. S. (2024) · ACS Omega · doi:10.1021/acsomega.3c08448 · Cited by 71
Self-citationThermal behavior and water absorption kinetics of polylactic acid/chitosan biocomposites
Kamaludin, N. H. I., Ismail, H., Rusli, A., & Ting, S. S. (2020) · Iranian Polymer Journal · doi:10.1007/s13726-020-00879-5 · Cited by 66
Poly(lactic acid) biocomposites with mango waste and organo‐montmorillonite for packaging
Lima, E. M. B., Lima, A. M., Minguita, A. P. D. S., dos Santos, N. R. R., Pereira, I. C. S., Neves, T. T. M., Gonçalves, L. F. D. C., Moreira, A. P., Middea, A., Neumann, R., et al. (2019) · Journal of Applied Polymer Science · doi:10.1002/app.47512 · Cited by 63
Paydayesh, A., Mousavi, S. R., Estaji, S., Khonakdar, H. A., & Nozarinya, M. A. (2021) · Polymer Composites · doi:10.1002/pc.26385 · Cited by 61
Reactive blending of thermoplastic starch, epoxidized natural rubber and chitosan
Jantanasakulwong, K., Leksawasdi, N., Seesuriyachan, P., Wongsuriyasak, S., Techapun, C., & Ougizawa, T. (2016) · European Polymer Journal · doi:10.1016/j.eurpolymj.2016.09.035 · Cited by 61
Bhat, V. G., Masti, S. P., Narasagoudr, S. S., Chougale, R. B., Kumar, S. K. P., Dalbanjan, N. P., & Malabadi, R. B. (2024) · Food Bioscience · doi:10.1016/j.fbio.2024.104402 · Cited by 61
Bakar, M. S. A., Asyraf, M. R. M., Syamsir, A., Ma, Q., Hazrati, K. Z., Azlin, M. N. M., Ali, M. M., Ghani, A., Lee, S. H., SaifulAzry, S. O. A., et al. (2024) · Polymer Composites · doi:10.1002/pc.28785 · Cited by 61
Chakravarty, J., Rabbi, M. F., Chalivendra, V., Ferreira, T., & Brigham, C. J. (2019) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2019.10.168 · Cited by 61
Azha, S. F., Shahadat, M., Ismail, S. B., Ali, S. W., & Ahammad, S. Z. (2021) · Journal of the Taiwan Institute of Chemical Engineers · doi:10.1016/j.jtice.2021.03.018 · Cited by 57
Abid, U., Gill, Y. Q., Irfan, M. S., Umer, R., & Saeed, F. (2021) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2021.03.057 · Cited by 52
Properties and Characterization of a PLA–Chitin–Starch Biodegradable Polymer Composite
Olaiya, N. G., Surya, I., Oke, P. K., Rizal, S., Sadiku, E. R., Ray, S. S., Farayibi, P. K., Hossain, M. S., & Khalil, H. P. S. A. (2019) · Polymers · doi:10.3390/polym11101656 · Cited by 48
Ranjbar‐Mohammadi, M., Shakoori, P., & Arab‐Bafrani, Z. (2021) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2021.07.160 · Cited by 44
Tithy, L. H., Rahman, A., Wong, S. Y., Xu, L., & Arafat, M. T. (2024) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2024.122111 · Cited by 38
Polylactide/Carbon Black Segregated Composites for 3D Printing of Conductive Products
Masiuchok, O., Iurzhenko, M. V., Kolisnyk, R. V., Mamunya, Y. P., Godzierz, M., Demchenko, V. L., Yermolenko, D., & Shadrin, A. O. (2022) · Polymers · doi:10.3390/polym14194022 · Cited by 39
Kalantari, K., & Afifi, A. M. (2018) · Separation Science and Technology · doi:10.1080/01496395.2018.1462388 · Cited by 37
“probably takes place between talc and polymer matrix as they are miscible.([23])”
BackgroundProperties of Macroalgae Biopolymer Films Reinforcement with Polysaccharide Microfibre
Rizal, S., Lai, T. K., Muksin, U., Olaiya, N. G., Abdullah, C. K., Ikramullah, I., Yahya, E. B., Chong, E. W. N., & Khalil, H. P. S. A. (2020) · Polymers · doi:10.3390/polym12112554 · Cited by 38
“These peaks are typically indicators of the presence of carrageenan in macroalgae biopolymer films [12].”
BackgroundPatwa, R., Saha, N., Sáha, P., & Katiyar, V. (2019) · Journal of Applied Polymer Science · doi:10.1002/app.47903 · Cited by 36
Mohamad, S. N. K., Ramli, I. B., Abdullah, L. C., Mohamed, N. H., Islam, M. S., Ibrahim, N. A., & Ishak, N. S. (2021) · Polymers · doi:10.3390/polym13111839 · Cited by 34
“This indicates that the addition of GO into CS/PLA composites will increase the efficiency interaction between the two components [37].”
BackgroundSelf-citationWang, Y., Liu, J., Xia, L., Shen, M., & Xin, Z. (2019) · Polymer Testing · doi:10.1016/j.polymertesting.2019.106077 · Cited by 33
Harikrishnan, M. P., Thampi, A., Lal, A. M. N., Warrier, A. S., Basil, M., & Kothakota, A. (2023) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2023.126888 · Cited by 32
Effects of chain extender and uniaxial stretching on the properties of PLA/PPC/mica composites
Xia, M., Shi, K., Zhou, M., Shen, Y., & Wang, T. (2019) · Polymers for Advanced Technologies · doi:10.1002/pat.4691 · Cited by 31
Tham, W. L., Poh, B. T., Ishak, Z. A. M., & Chow, W. S. (2015) · Journal of Applied Polymer Science · doi:10.1002/app.42850 · Cited by 30
Cosme, J. G. L., da Silva, V. M., Nunes, R. C. R., & Picciani, P. H. S. (2016) · Materials Sciences and Applications · doi:10.4236/msa.2016.74021 · Cited by 38
“Recently, the use of biodegradable and biocompatible polymers has become increasingly important due to their fascinating characteristics such as natural abundance, low costs, and wide range of applications [16].”
BackgroundAli, Q., Taweepreda, W., & Techato, K. (2019) · Polymer Testing · doi:10.1016/j.polymertesting.2019.106294 · Cited by 28
Tham, W. L., Poh, B. T., Ishak, Z. A. M., & Chow, W. S. (2016) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-016-5834-7 · Cited by 29
Guerra, N. B., Cassel, J. B., Henckes, N. A. C., de Oliveira, F. D. S., Lima, E. O. C., & dos Santos, L. A. (2018) · Journal of Polymer Research · doi:10.1007/s10965-018-1542-2 · Cited by 27
Boonmahitthisud, A., Mongkolvai, A., & Chuayjuljit, S. (2021) · Journal of Polymers and the Environment · doi:10.1007/s10924-021-02063-z · Cited by 25
“There are numerous studies for either PLA/NR or PLA/ENR composites reinforced with fillers such as talc [1], multiwalled carbon nanotube [26], chitosan [27], graphene oxide [28], catappa leaves [29], halloysite [30], but only a few studies have focused on determining the reinforcement of nSiO2 in PLA/ENR composites.”
BackgroundSynthesis and characterization of chitosan/TiO2 nanocomposite for the adsorption of Congo red
Habiba, U., Joo, T. C., Shezan, S. A., Das, R., Ang, B. C., & Afifi, A. M. (2019) · Desalination and Water Treatment · doi:10.5004/dwt.2019.24391 · Cited by 24
“Thus, inter facial adhesion between chitosan matrix and TiO2 particles is believed to be poor [17].”
BackgroundDeposition of Cu/a-C:H Nanocomposite Films
Hanuš, J., Steinhartova, T., Kylián, O., Kousal, J., Malinský, P., Choukourov, A., Macková, A., & Biederman, H. (2016) · Plasma Processes and Polymers · doi:10.1002/ppap.201500208 · Cited by 24
Properties enhancement of chitosan‐filled polylactic acid biocomposites using tannic acid treatment
Kamaludin, N. H. I., Ismail, H., Rusli, A., & Ting, S. S. (2021) · Polymer Composites · doi:10.1002/pc.26354 · Cited by 23
Gaweł, A., & Kuciel, S. T. (2020) · Polymers · doi:10.3390/polym12123056 · Cited by 22
Olaiya, N. G., Nuryawan, A., Oke, P. K., Khalil, H. P. S. A., Rizal, S., Mogaji, P. B., Sadiku, E. R., Ray, S. S., Farayibi, P. K., Ojijo, V. O., et al. (2020) · Polymers · doi:10.3390/polym12030592 · Cited by 22
“[23] have reported that the best mechanical properties of a PLA/chitin composite are with 5% chitin.”
BackgroundChitosan as a Polyfunctional Crosslinker for a Renewable-Based Resorcinol Diglycidyl Ether
Fusteș-Dămoc, I., Măluţan, T., & Mija, A. (2023) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.3c01429 · Cited by 18
Yeo, J. C. C., Muiruri, J. K., Lee, P. S. K., Raveenkumar, V., Lin, T., Zhang, X., Thitsartarn, W., Hadjichristidis, N., He, C., & Li, Z. (2024) · Advanced Composites and Hybrid Materials · doi:10.1007/s42114-024-00983-7 · Cited by 18
Selwin, M., Rajini, N., Ponsuriyaprakash, S., Oluwarotimi, I. S., Krishnan, K., Mohammad, F., Shaik, M. R., & Ayrılmış, N. (2024) · JOURNAL OF RENEWABLE MATERIALS · doi:10.32604/jrm.2024.052952 · Cited by 16
“Zakaria et al. [19] discussed the potential of PLA to bind with various additives and improve its properties, highlighting its biodegradability and biocompatibility.”
Altuntaş, E., & Aydemir, D. (2019) · Maderas Ciencia y tecnología · doi:10.4067/s0718-221x2019005000416 · Cited by 16
“The fractured surface was also determined to be smooth and homogeneous surfaces upon incorporation of CS in the PLA matrix (Zakaria et al. 2013).”
MethodChaiwutthinan, P., Chauyjuljit, S., Thipkham, N., Kowalski, C. P., & Boonmahitthisud, A. (2019) · Journal of Vinyl and Additive Technology · doi:10.1002/vnl.21697 · Cited by 16
Boonluksiri, Y., Siangdang, P., Johns, J., & Nakaramontri, Y. (2024) · Industrial Crops and Products · doi:10.1016/j.indcrop.2024.119102 · Cited by 14
Bedir, T., Ulağ, S., Aydogan, K., Şahin, A., Karademir-Yilmaz, B., Güvenç, Y., Bozlar, M., Üstündağ, C. B., & Gündüz, O. (2020) · Polymers for Advanced Technologies · doi:10.1002/pat.5159 · Cited by 15
Mustafa, S. N. I. S., Man, S. H. C., Hassan, A., & Baharulrazi, N. (2020) · AIP conference proceedings · doi:10.1063/5.0022360 · Cited by 13
Self-citationLi, W., Shen, J., Srithep, Y., Worajittiphon, P., & Liu, S. (2025) · Polymers for Advanced Technologies · doi:10.1002/pat.70178 · Cited by 12
Applications of rubber-based blends
Popescu, R. C., Popescu, D., & Grumezescu, A. M. (2016) · Elsevier eBooks · doi:10.1016/b978-0-08-100408-1.00004-2 · Cited by 12
Gupta, M., & Singh, A. (2025) · Journal of Inorganic and Organometallic Polymers and Materials · doi:10.1007/s10904-025-03624-8 · Cited by 11
“CS with Epoxidised Natural Rubber (ENR) improved filler interac - tion and mechanical strength and was incorporated with the PLA matrix through solution casting [31].”
Fekiač, J. J., Kakošová, L., Krbaťa, M., Kohutiar, M., Eckert, M., Studený, Z., & Dubec, A. (2025) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp9040134 · Cited by 17
Fitri, M. F. M., Asyraf, M. R. M., & Hassan, S. A. (2024) · Jurnal Kejuruteraan · doi:10.17576/jkukm-2024-36(5)-25 · Cited by 11
Taranamai, P., Phinyocheep, P., Panbangred, W., Janhom, M., & Daniel, P. (2019) · Journal of Materials Science · doi:10.1007/s10853-019-03599-1 · Cited by 11
Influence of Chitosan and Grape Seed Extract on Thermal and Mechanical Properties of PLA Blends
Goetjes, V., von Boyneburgk, C. L., Heim, H., & Horn, M. M. (2023) · Polymers · doi:10.3390/polym15061570 · Cited by 9
“reported an increase in tensile strength when 5% chitosan was used in PLA–chitosan blends, a further increase in the polysaccharide concentration implied a reduction in the tensile strength [28].”
BackgroundThermal and Mechanical Properties of Biodegradable Star‐Shaped/Linear Polylactide Stereocomplexes
Cheerarot, O., & Baimark, Y. (2015) · Journal of Chemistry · doi:10.1155/2015/206123 · Cited by 9
Mehwish, N., Kausar, A., Siddiq, M., & Raheel, M. (2014) · Journal of Plastic Film & Sheeting · doi:10.1177/8756087914555045 · Cited by 9
“Tensile modulus of the PVDF/SBS-MWCNT-based membranes prepared was found to be higher than literature elastomeric membranes having values up to 5MPa.(32,33) 128 Journal of Plastic Film & Sheeting 31(2)”
MethodValente, M., Puiggalí, J., del Valle, L. J., Titolo, G., & Sambucci, M. (2021) · Polymers · doi:10.3390/polym13162751 · Cited by 9
“This behavior is attributable to several possible reasons [27,28]: (a) The flaked morphology of CS reduces the interlocking with the PCL matrix; (b) the strong difference in polarity between PCL and CS results in phase-separated composites, reducing the mechanical properties; and (c) the non-optimal concentration of C…”
ResultKamaludin, N. H. I., Ismail, H., Rusli, A., & Sam, S. T. (2021) · Journal of Vinyl and Additive Technology · doi:10.1002/vnl.21816 · Cited by 8
Kamaludin, N. H. I., Ismail, H., Rusli, A., Sam, S. T., & Gunny, A. A. N. (2020) · AIP conference proceedings · doi:10.1063/5.0016532 · Cited by 8
Evaluation and Enhancement of Polylactic Acid Biodegradability in Soil by Blending with Chitosan
Kamaludin, N. H. I., Ismail, H., Rusli, A., Sam, S. T., & Osman, H. (2023) · Journal of Polymers and the Environment · doi:10.1007/s10924-023-02762-9 · Cited by 7
“This is based on the fact that natural fillers could improve the performance of PLA-based biocomposites, in particular its mechanical properties [22], while enhancing their degradation efficiency [23], apart from low cost [24].”
BackgroundChitosan-reinforced nitrile rubber – a step towards sustainable development
Rahim, S. A., Unnikrishnan, G. P., Joseph, M. A., Ali, M. M., & Afzal, A. (2021) · Plastics Rubber and Composites Macromolecular Engineering · doi:10.1080/14658011.2021.1991166 · Cited by 7
Tensile Behavior of SiCNP and MWCNTs Filled Toughened Epoxy Nanocomposites: A Comparative Study
Ratim, S., Ahmad, S., Bonnia, N. N., Ali, E. S., & Razak, J. A. (2016) · Procedia Chemistry · doi:10.1016/j.proche.2016.03.098 · Cited by 7
Ramamurthy, M., Vasanthkumar, P., Perumal, G., & Senthilkumar, N. (2025) · Journal of Environmental Nanotechnology · doi:10.13074/jent.2025.03.243932 · Cited by 6
The Strength characteristics of Chitosan- and Titanium- Poly (L-lactic) Acid Based Composites
Aworinde, A. K., Adeosun, S. O., Oyawale, F. A., Akinlabi, E. T., & Akinlabi, S. A. (2019) · Journal of Physics Conference Series · doi:10.1088/1742-6596/1378/2/022061 · Cited by 6
“% filler addition, are indications of the presence of chitosan [26], [33].”
BackgroundGuerra, N. B., Cassel, J. B., Muniz, N. O., Henckes, N. A. C., de Oliveira, F. D. S., Lima, E. O. C., & dos Santos, L. A. (2021) · Fibers and Polymers · doi:10.1007/s12221-021-0971-4 · Cited by 6
Chełminiak-Dudkiewicz, D., Macháček, M., Długaszewska, J., Mylkie, K., Smolarkiewicz-Wyczachowski, A., Kozlíková, M., Druzyński, S., Krygier, R., & Ziegler-Borowska, M. (2025) · Materials Advances · doi:10.1039/d5ma00029g · Cited by 5
Lee, D., Kao, C.-W., Huang, T., You, J.-H., & Liu, S. (2016) · International Polymer Processing · doi:10.3139/217.3082 · Cited by 5
“However, the use of pure chitosan has been limited due to its poor mechanical properties, weak barrier properties of the membrane and high moisture sensitivity (Zakaria et al., 2013).”
Thomas, M. S., Koshy, R. R., Mary, S. K., Thomas, S., & Pothan, L. A. (2018) · Springer briefs in molecular science · doi:10.1007/978-3-030-03158-9_3 · Cited by 5
Green Adhesives for Biomedical Applications
dos Santos, J. R. A., de Macedo, A. T., Santana, A. A., de Souza, M. E. P., Holanda, R. A., & Cruz, G. (2020) · Wiley eBooks · doi:10.1002/9781119655053.ch4 · Cited by 5
Dağdelen, A. F., Demirel, F. T. K., & Sarıcaoğlu, F. T. (2024) · GIDA / THE JOURNAL OF FOOD · doi:10.15237/gida.gd23131 · Cited by 3
Asri, S. E. A. M., Zakaria, Z., Hassan, A., Kassim, M. H. M., & Arjmandi, R. (2021) · Malaysian Journal of Fundamental and Applied Sciences · doi:10.11113/mjfas.v17n2.2002 · Cited by 3
“However, PLA have several weakness such as brittleness and poor thermal stability (Zakaria et al., 2013; Arjmandi et al., 2015).”
BackgroundSelf-citationKanani, N., Rahmayetty, R., Wardhono, E. Y., & Wardalia, W. (2022) · Materials science forum · doi:10.4028/p-bs885y · Cited by 3
“Chitosan (CH) is well known as high versatile material due to it’s biodegradable, biocompatible, antifungal and antimicrobial activity [12], however chitosan (CH) are typically poor in mechanical properties, fragile, weak barrier properties of film, high moisture sensitivity and water-insoluble material [13][14].”
BackgroundDevelopment of mandelic acid-loaded electrospun nanofibers as a wound dressing material
Koru, Z. E., Yeşiltepe, O., Güldü, Ö. K., Kırbay, F. Ö., Medine, E. İ., Vural, C., & Demirkol, D. O. (2025) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2025.131054 · Cited by 2
Morphological characteristics of elastomer blends and composites
Kiruthika, A. V. (2022) · Elsevier eBooks · doi:10.1016/b978-0-323-85832-8.00013-4 · Cited by 2
Mechanical and Rheological Properties of Biodegradable Polycaprolactone/Carbon Nanotube Composites
Lebedev, S. M., & Amitov, E. T. (2020) · Russian Physics Journal · doi:10.1007/s11182-020-02066-8 · Cited by 2
Pengembangan Bioplastik Antibakteri Untuk Bahan AAlat Pelindung Diri (APD) yang Ramah Lingkungan
Suhendar, D., Rasman, G. E., & Sutrisno, A. (2021) · Jurnal Health Sains · doi:10.46799/jhs.v2i9.270 · Cited by 1
Degradation Test of Natural Rubber/Chitosan Composite
Sukthaworn, C., Reowdecha, M., Dittanet, P., Moonprasith, N., Lampang, T. N., Loykulnant, S., & Prapainainar, P. (2017) · Key engineering materials · doi:10.4028/www.scientific.net/kem.751.320 · Cited by 1
Hakim, A. A. A., & Wahidah, N. R. (2015)
Polylactic Acid Based Rubber Composites and Nanocomposites
Dehbari, N., Tang, Y., & Moazeni, N. (2017) · Advanced structured materials · doi:10.1007/978-3-319-48806-6_7
Poly (Lactic Acid) Nanocomposites Reinforced with Different Additives
Valapa, R. B., Valapa, R. B., Pugazhenthi, G., & Katiyar, V. (2017) · Wiley eBooks · doi:10.1002/9781119441632.ch141
Kazushi, I. T. O., Takahashi, T., & Hedeaki, M. O. R. I. (2019) · Journal of the Society of Materials Engineering for Resources of Japan · doi:10.5188/sjsmerj.30.1_2_11
Biotechnological Advances in Chitin and Chitosan-Based Biocomposites: Challenges and Opportunities
Maniyan, V., & Panda, S. K. (2025) · Interdisciplinary biotechnological advances · doi:10.1007/978-981-96-6354-5_1
Chitin and Chitosan Bio-Whisker-Reinforced Polymer Blends
Rajendran, A. K., Padmanabhan, D., Ashokkumar, V., Muthusamy, S., & Senthilkumar, P. (2025) · Interdisciplinary biotechnological advances · doi:10.1007/978-981-96-6354-5_4
Bajpai, P. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-33524-2.00006-5
Natural Rubber‐Based Bio‐Composites and Bio‐Nanocomposites
Mnyango, J. I., Khumalo, M. V., & Hlangothi, S. P. (2025) · Wiley eBooks · doi:10.1002/9781394213825.ch3 · Cited by 1
Ecocompósitos multiescala para componentes de automóveis
Vieira, C. E. F. (2023) · Portuguese National Funding Agency for Science, Research and Technology (RCAAP Project by FCT)
Matériaux polymères durables synthétisés à base d'oligo- et de polysaccharides
Fusteș-Dămoc, I. (2023) · theses.fr (ABES) · doi:10.70675/3c68f3acz8bcfz48eaz86f3z6e89f17363a6
Metadata
- Authors
- Zakaria, Z., Islam, M. S., Hassan, A., Mohamad Haafiz, M. K., Arjmandi, R., Inuwa, I. M., & Hasan, M.
- Affiliations
- University of Technology Malaysia (MY)
- Universiti Putra Malaysia (MY)
- Department of Polymer Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor, Malaysia
- Corresponding author
- Zakaria, Zainoha
- Venue
- Advances in Materials Science and Engineering
- Publisher
- Wiley
- Published
- 2013
- Volume
- 2013
- Pages
- 1-7
- ISSN
- 1687-8434 (ISSN-L)
- 1687-8442
- OpenAlex
- W2032977557
- Cited by
- 89
- References
- 28
- Citations by year
- 2025: 9 · 2024: 8 · 2023: 5 · 2022: 4 · 2021: 14 · 2020: 9 · 2019: 15 · 2018: 5 · 2017: 3 · 2016: 10 · 2015: 6 · 2014: 1
- FWCI
- 4.09
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- Advances in Materials Science and Engineering (publishedVersion, cc-by)
- Aston Publications Explorer (Aston University) (submittedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Greater South Information System
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Natural Fiber Reinforced Composites
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Biomaterials › Nanocomposite Films for Food Packaging
- Keywords
- polylactic acid, chitosan, epoxidized natural rubber, polymer blends, natural polymer composites, tensile strength, Young's modulus, elongation at break, phase segregation, interfacial adhesion, filler dispersion, polymer-polymer interactions
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.