Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers
Open accessThe DOI matches its Crossref record; 106 of the 106 references it cites were found in a registry or an index; 1 of the 14 sources its claims cite were checked for support.
Abstract
Incinerators are widely used to burn the municipal waste, biowaste, wood, straw, and biomedical waste. Combustion of these types of waste results in generation of chlorides of sodium and potassium which may attack the metallic part of the incinerator. In biofuel-fired boilers, similar type of highly corrosive environment is present. Attempt has been made to review the corrosion problems and their solutions as per the available literature.
Overview
CoChat Summary
TL;DR
This review summarizes high-temperature corrosion problems in incinerators and biomass-fuel-fired boilers, focusing on alkali chlorides and sulphates, active oxidation, and remedial measures such as sulphur additives and thermal-spray coatings. It concludes that chlorine is mainly responsible for damage to protective oxide scales and that coatings and inhibitors can extend component life.
Key findings
- Incineration reduces waste mass by 70% and volume by up to 90% while producing energy, but fireside corrosion causes unforeseen shutdowns; chlorides and sulphates form molten salts on superheater tubes, with NaCl and KCl causing severe corrosion.
- Chlorine/alkali chlorides drive active oxidation, leading to volatile species, porous scale, internal oxidation, and metal loss; Ni-based superalloys resist chloride-containing environments but are susceptible to sulphur-containing environments, while Cr₂O₃-forming alloys are prone to alkaline flux dissolution.
- In Swedish power stations fired with 100% wood-based biofuels, conventional low-chromium ferritic superheater steels had to be replaced after about 20,000 hours if steam temperature was 470°C or higher. Addition of sulphur or sulphur-containing compounds decreased corrosion rate by 50–70%; ammonium sulphate halved the corrosion rate of ferritic/martensitic steels in a wood-fired boiler, and 300 ppm SO₂ drastically reduced corrosion rate.
- D-gun and HVOF sprayed coatings such as 50% Ni-50% Cr, alloy 625, NiCrBSiFe, and alloy 718 performed well; D-gun sprayed 50% Ni-50% Cr in an actual refuse incineration plant operated for about 7 years without problems, and alloy 625, NiCrBSiFe, and alloy 718 performed better than alloy C-276 under simulated biomass combustion conditions.
Methods
- Narrative literature review of corrosion studies in incinerators and biomass-fuel-fired boilers; no original experimental work by the authors is described.
- The review compiles studies on boiler steels, superalloys, and thermal-spray coatings exposed to chloride- and sulphate-containing environments, including NaCl, KCl, Na₂SO₄, V₂O₅, HCl, and SO₂ at various temperatures.
- Main analysis is a qualitative synthesis and tabulation of alloy/coating performance under simulated and actual incinerator/biomass boiler conditions; no systematic search strategy or quantitative meta-analysis is described.
Limitations
- Not stated in the paper: the paper has no explicit limitations section.
- Evident from the text: it is a narrative review without described systematic search, inclusion, or quality-assessment criteria.
- Evident from the text: the summary table is incomplete/fragmented in the provided text, and cited studies use varied environments, temperatures, exposure times, and materials, limiting direct comparability.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 0 Not valid · 13 Not checked · 11 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Normally, incinerators are operated at high temperature between 300 ∘ C and 1100 ∘ C based on volume and type of waste, incinerator, and fuel used [5].”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 1. Introduction
What the sources say
- Partly supportedcites [5] 5. S. W. Manyele and I. S. Kagonji, "Analysis of medical waste incinerator performance based on fuel consumption and cycle times, " Engineering, vol. 4, pp. 625-635, 2012. sourceExperimental — accuracy not yet measured
Section 2.1 describes medical-waste incineration at 850–1000°C and says exhaust gases can reach 1100°C. Section 2.5 gives a typical primary-chamber range of 500–800°C. These passages support high-temperature operation, but not a normal operating range starting at 300°C or the stated dependence of that range on waste volume, waste type, incinerator, and fuel. (LLM, conf=0.85)
- Partly supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“From table it can be seen that NaCl will lead to severe corrosion.Alloy steels and superalloys are resistant to sulphates environment but addition of chlorides increases the corrosion rate manifolds.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 6. Discussion
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Active oxidation is the main mechanism for the corrosion in chlorides environment leading to mass loss due to formation of volatile species, formation of porous scale, and internal oxidation.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 6. Discussion
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“(3) Researchers showed that presence of chlorine in environment is mainly responsible for the damage of protective oxide.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 7. Conclusions
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“(5) Coating can be sprayed using different thermal spray technique which can save the material from direct contact with the salt and hence enhance the life.Already, D-gun and HVOF sprayed coatings such as 50% Ni-50% Cr, alloy 625, NiCrBSiFe, and alloy 718 have been tried in simulated refuse incinerator and biomass-fuel-fired boiler environment and had shown good performance.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 7. Conclusions
20 more claims
Create a free account to see all 25 claims and every source verdict.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 2. High Temperature Corrosion Problem in Incinerator
“Miller and Krause [18] found that accumulation of elements such as sulphur, chlorine, zinc, aluminium, potassium, and occasionally lead and copper occurred at the metal/scale interface as a deposit in municipal incinerators.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > References
“18. W. Ma and S. Rotter, "Overview on the chlorine origin of MSW and Cl-originated corrosion during MSW & RDF combustion process, "”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > Biofuel Boiler
“Low alloyed ferritic steel EN1.7380 [Fe-2.25Cr-1Mo]”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > Biofuel Boiler
“the austenitic EN1.7380 [Fe-18Cr-9Ni]”
Citations
Cites
Production of first and second generation biofuels: A comprehensive review
Naik, S. N., Goud, V. V., Rout, P. K., & Dalai, A. K. (2010) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2009.10.003 · Cited by 3,264
Biomass combustion in fluidized bed boilers: Potential problems and remedies
Khan, A. A., de Jong, W., Jansens, P. J., & Spliethoff, H. (2009) · Fuel Processing Technology · doi:10.1016/j.fuproc.2008.07.012 · Cited by 1,122
The implications of chlorine-associated corrosion on the operation of biomass-fired boilers
Nielsen, H. P., Frandsen, F. J., Dam-Johansen, K., & Baxter, L. L. (2000) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(00)00003-4 · Cited by 785
Biomass-coal co-combustion: opportunity for affordable renewable energy
Baxter, L. (2005) · Fuel · doi:10.1016/j.fuel.2004.09.023 · Cited by 588 · cited 1×
“Apart from these benefits some technical issues associated with cofiring include fuel supply, handling and storage challenges, potential increase in corrosion, decrease in overall efficiency, ash deposition issues, pollutant emissions, carbon burnout impacts on ash marketing, impacts on selective catalytic reduction (…”
BackgroundGrabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Zahs, A., Spiegel, M., & Grabke, H. J. (2000) · Corrosion Science · doi:10.1016/s0010-938x(99)00142-0 · Cited by 365
High temperature corrosion of coatings and boiler steels below chlorine-containing salt deposits
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. A. (2004) · Corrosion Science · doi:10.1016/j.corsci.2003.09.026 · Cited by 260
High-Temperature Corrosion in Waste-to-Energy Boilers
Lee, S.-H., Themelis, N. J., & Castaldi, M. J. (2007) · Journal of Thermal Spray Technology · doi:10.1007/s11666-006-9005-4 · Cited by 178
Ishitsuka, T., & Nose, K. (2002) · Corrosion Science · doi:10.1016/s0010-938x(01)00059-2 · Cited by 177
A review on biomass classification and composition, co-firing issues and pretreatment methods
Tumuluru, J. S., Wright, C. T., Boardman, R. D., Yancey, N. A., & Sokhansanj, S. (2011) · 2011 Louisville, Kentucky, August 7 - August 10, 2011 · doi:10.13031/2013.37191 · Cited by 158 · cited 1×
“It is found that there is a growing interest in the use of biofuels for energy purposes due to various reasons such as reduction in dependency on imported oil, generation of 20 times more employment, mitigation of greenhouse gases [38–40], and reduction of acid rain [41].”
Background
Research works printed but not linked: 15
- 2011, International Journal of Geology, Earth and Environment Sciences, 1, 48
- 1999, Oxidation of Metals, 51, 507
- 2001, NKK Technical Review, 38
- 1997, Materials at High Temperatures, 14, 137
- 2004, Materials Science Forum, 461-464, 1055
- 2012, Journal of Achievements in Materials and Manufacturing Engineering, 54, 58
- 2010, International Journal of Energy and Environment, 1, 667
- 2006, International Journal of Physical Sciences, 1, 27
- 1996, Materials Letters, 29, 19
- 2012, Anbar Journal For Engineering Sciences, 12
- 1999, Oxidation of Metals, 51, 353
- 2013, High Temperature Materials and Processes, 323, 317
- 2013, Research Inventy, 2, 31
- 2007, Materials Science Forum, 546-549, 1739
- 1989, Materials Science and Engineering A, 120-121, 61
Cited by
Ma, W., Wenga, T., Frandsen, F. J., Yan, B., & Chen, G. (2020) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2019.100789 · Cited by 275
Sadeghi, E., Markocsan, N., & Joshi, S. V. (2019) · Journal of Thermal Spray Technology · doi:10.1007/s11666-019-00938-1 · Cited by 164
A review of biomass ash related problems: Mechanism, solution, and outlook
Abioye, K. J., Harun, N. Y., Sufian, S., Yusuf, M., Jagaba, A. H., Ekeoma, B. C., Kamyab, H., Sikiru, S., Waqas, S., & Ibrahim, H. (2024) · Journal of the Energy Institute · doi:10.1016/j.joei.2023.101490 · Cited by 135
Ma, Z. G., Knotzer, A., Billanes, J. D., & Jôrgensen, B. N. (2020) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2020.109750 · Cited by 112
Environmental implications of the quality of charcoal briquettes and lump charcoal used for grilling
Jelonek, Z., Drobniak, A., Mastalerz, M., & Jelonek, I. (2020) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2020.141267 · Cited by 79
Biomass briquette fuel, boiler types and pollutant emissions of industrial biomass boiler: A review
Huang, H. Z., Gao, Y., Chen, H., Wu, Y., Wang, J., Yu, C., Li, J., & Zou, C. (2022) · Particuology · doi:10.1016/j.partic.2022.08.016 · Cited by 81
Kassim, S. A., Thor, J. A., Seman, A. A., & Abdullah, T. K. (2020) · Corrosion Science · doi:10.1016/j.corsci.2020.108761 · Cited by 64
Sadeghi, E., Markocsan, N., & Joshi, S. V. (2019) · Journal of Thermal Spray Technology · doi:10.1007/s11666-019-00939-0 · Cited by 60
Zhou, S., Liu, C., & Zhang, L. (2019) · Energy & Fuels · doi:10.1021/acs.energyfuels.9b02958 · Cited by 50
Maj, I., Kalisz, S., Wejkowski, R., Pronobis, M., & Gołombek, K. (2022) · Fuel · doi:10.1016/j.fuel.2022.124749 · Cited by 53
Zeng, Y., Li, K., Hughes, R. W., & Luo, J. (2017) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.7b03664 · Cited by 49
Corrosion of heat exchanger materials in co-combustion thermal power plants
Li, K., & Zeng, Y. (2022) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2022.112328 · Cited by 55
Zhang, X., Liu, H., Chen, T., Wang, G., Li, H., Hu, H., Yu, Y., & Yao, H. (2020) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c02145 · Cited by 46
Goli, V. S. N. S., Singh, D. N., & Başer, T. (2021) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2021.105643 · Cited by 44
Effect of grain size on high-temperature corrosion performance of laser cladding inconel 625 coating
Peng, J., Li, K., Xie, Z., Tan, L., Wang, Y., Liu, F., & Liu, Y. (2024) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2024.10.052 · Cited by 41
Heat transfer and ash deposition performance of heat exchange surface in waste incineration flue gas
Zhang, Y., Du, X., Yue, M., Yan, M., & Shi, Y. (2020) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.119691 · Cited by 37
Wenga, T., Macdonald, D. D., & Ma, W. (2024) · Progress in Materials Science · doi:10.1016/j.pmatsci.2024.101359 · Cited by 36
Emissions during grilling with wood pellets and chips
Jelonek, Z., Drobniak, A., Mastalerz, M., & Jelonek, I. (2021) · Atmospheric Environment X · doi:10.1016/j.aeaoa.2021.100140 · Cited by 34
Setyan, A., Patrick, M., & Wang, J. (2017) · Atmospheric Environment · doi:10.1016/j.atmosenv.2017.07.018 · Cited by 27
Assessing pellet fuels quality: A novel application for reflected light microscopy
Jelonek, Z., Drobniak, A., Mastalerz, M., & Jelonek, I. (2020) · International Journal of Coal Geology · doi:10.1016/j.coal.2020.103433 · Cited by 22
Long-term Hot Corrosion Behavior of Boiler Tube Alloys in Waste-to-Energy Plants
Liu, J., Dyson, D., & Asselin, E. (2016) · Oxidation of Metals · doi:10.1007/s11085-016-9627-y · Cited by 18
Wei, Z., Liang, X., Wang, L., Yuan, Z., & Wu, L. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.115973 · Cited by 21
Adoption of strategies for clean combustion of biomass in boilers
Sharma, S., Sharma, M., Mudgal, D., & Bhowmick, H. (2021) · Corrosion Reviews · doi:10.1515/corrrev-2020-0095 · Cited by 23
Self-citationEffect of Hydrogen Chloride on Corrosion Behaviour of Fe–Cr Alloys in Wet CO2 Gas at 650 °C
Aye, K. K., Zhang, J., & Young, D. J. (2020) · Oxidation of Metals · doi:10.1007/s11085-020-09978-3 · Cited by 15
“However, a major obstacle in incinerators is the severe fire-side corrosion of superheater tubes by the flue gas and fly ash deposits produced by waste combustion [2].”
BackgroundLariot-Sánchez, C., Gutierrez, A. R., Rodríguez–Machín, L., Rubio-González, A., & Quintero, P. J. I. (2022) · Oxidation of Metals · doi:10.1007/s11085-022-10102-w · Cited by 19
“[64] also recommends the addition of sulphur or sulphur-containing components to the fuel to decrease corrosion.”
BackgroundXie, Z., Liu, B., Fu, A., Li, K., Cao, Y., Zhou, H. M., Peng, J., & Liu, Y. (2024) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2024.131429 · Cited by 18
Commoditization of wet and high ash biomass: wet torrefaction—a review
Mościcki, K., Niedźwiecki, Ł., Owczarek, P., & Wnukowski, M. (2016) · Journal of Power Technologies · Cited by 19
A short review on the performance of high velocity oxy-fuel coatings in boiler steel applications
Parkash, J., Saggu, H. S., & Vasudev, H. (2021) · Materials Today Proceedings · doi:10.1016/j.matpr.2021.09.014 · Cited by 8
Effect of hot corrosion on the bimetallic joints employed in the coal-fired boiler
Prabu, S. S., Ramkumar, K. D., & Arivazhagan, N. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab43fd · Cited by 8
Effect of Temperature on Corrosion Behaviour of Fe–Cr Alloys in Wet CO2 With and Without HCl Gases
Aye, K. K., Cai, Y., Zhang, J., & Young, D. J. (2022) · Oxidation of Metals · doi:10.1007/s11085-021-10092-1 · Cited by 7
Mudgal, D., Ahuja, L., Singh, S. P., & Prakash, S. (2016) · Materials at High Temperatures · doi:10.1080/09603409.2016.1234663 · Cited by 8
“[5] Hence, burning of hazardous/medical waste requires very high temperature to destroy waste along with microorganism.[6,7] Such high temperature in the furnace and boilers can lead to various corrosion problems which includes scaling, fluxing, fouling, hot corrosion, oxidation, sulfidationor erosion.”
BackgroundSelf-citationJin, L., Lindberg, D., Tsuchiyama, Y., & Robelin, C. (2022) · Chemical Engineering Science · doi:10.1016/j.ces.2022.117847 · Cited by 7
Roshith, P., & Arivarasu, M. (2022) · Engineering Research Express · doi:10.1088/2631-8695/ac5ebd · Cited by 7
Biomass to Energy: Scope, Challenges and Applications
Raina, S., Singh, H. M., Kothari, R., Singh, A., Allen, T., Pandey, A. K., & Tyagi, V. V. (2022) · Microorganisms for sustainability · doi:10.1007/978-981-19-2912-0_1 · Cited by 8
Application of modified Kalina cycle in biomass chp plants
Jaćimović, B., Genic, S. B., & Jaćimović, N. (2020) · International Journal of Energy Research · doi:10.1002/er.5570 · Cited by 7
“Owing to their lower melting points, molten chlorides are more frequently encountered.(24) In general, ORC can be suggested to be used in biomass power plants for the electrical power output of 0.”
BackgroundRoshith, P., & Arivarasu, M. (2022) · Welding International · doi:10.1080/09507116.2022.2089608 · Cited by 7
Use of hornbeam, pine and MDF waste in wood-polymer composites as construction elements
Atay, H. Y., & Türkmen, M. (2022) · Journal of the Indian Academy of Wood Science · doi:10.1007/s13196-022-00303-w · Cited by 7
“To put an end to this, finding ways to use the generated waste (without burning/destroying) seems to be the best solution, one of which is the method of reinforcing wood-polymer composites (Mudgal et al. 2014).”
MethodPrediction of biomass corrosiveness over different coatings in fluidized bed combustion
Contreras, M. L., Benito, M., & Bahillo, A. (2022) · International journal of energy and environmental engineering · doi:10.1007/s40095-022-00544-y · Cited by 7
“There are studies on different aspects of coatings, including wear [28] or erosioncorrosion performance [29], hot corrosion [30] low-temperature corrosion [31] and corrosion in supercritical boilers [32].”
BackgroundVerma, R., Kaushal, G., & Bala, N. (2023) · Journal of Thermal Spray Technology · doi:10.1007/s11666-023-01569-3 · Cited by 6
Sundaram, S., Singaravelu, C., & Vikneswaran, M. (2022) · Surface Topography Metrology and Properties · doi:10.1088/2051-672x/aca3be · Cited by 5
“The addition of compounds containing sulfur to the fuel by a thermal spray of 50% Ni-50% Cr, IN625, NiCrBSiFe, and alloy 718 decreased the rate of corrosion in incinerators and biofuel-fired boilers [21].”
BackgroundA SELECTION OF THE APPLICATION OF PINUS SYLVESTRIS L. FROM PUSZCZA NOTECKA BY CHEMICAL ANALYSIS
Zborowska, M., Pradzynski, W., Kusiak, W., Stachowiak–Wencek, A., Roszyk, E., & Moliński, W. (2018) · Drewno Prace Naukowe Doniesienia Komunikaty = Wood Research Papers Reports Announcements · doi:10.12841/wood.1644-3985.d10.02 · Cited by 4
“For example, the high content of chlorine is the reason for exploitation problems of boilers such as chloride corrosion [Mudgal et al. 2014].”
BackgroundRaclavská, H., Růžičková, J., Švédová, B., Kucbel, M., Šafář, M., Raclavský, K., & Abel, E. L. D. S. (2022) · Wiley eBooks · doi:10.1002/9781119679523.ch5 · Cited by 9
Usman, A., Isern, L., Nicholls, J. R., Cordero-Cabrera, M. C., & Syed, A. U. (2025) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-025-11630-7 · Cited by 3
“10, 11) and four salt-deposited coating samples (Fig.”
Huda, M. Y. Q., Wibawa, I. G. A. C. S., & Novendianto, I. B. (2022) · International Conference on Power Engineering and Renewable Energy (ICPERE) · doi:10.1109/icpere56870.2022.10037322 · Cited by 2
Sah, S. P., & Nishikata, A. (2022) · Springer eBooks · doi:10.1007/978-981-19-4767-4_7 · Cited by 2
Arias-Guerrero, D. A., Castillo-Hernández, M., Mayorga-Guzmán, J. D., et al. (2026) · Biofuels · doi:10.1080/17597269.2025.2599597 · Cited by 1
“This explains why fer-ritic steels exposed to high-Cl biomass like EFB may suffer premature failure unless mitigation strategies such as fuel additives or advanced coatings are employed [31].”
Mitigation of steel corrosion in waste-to-energy from poultry litter by modifying ash chemistry
Maj, I., Niesporek, K., Matus, K., Płaza, P., Miccio, F., & Maier, J. (2026) · Waste Management · doi:10.1016/j.wasman.2026.115745 · Cited by 1
Roshith, P. (2024) · Canadian Metallurgical Quarterly · doi:10.1080/00084433.2024.2367187 · Cited by 1
Organic waste materials as fuels in boilers: challenges and solutions
Posada, E., Jaramillo, M., & Saenz, G. (2012) · Engineering & Technology Reference · doi:10.1049/etr.2016.0026
Singh, R., Singh, G., & Sidhu, H. S. (2023) · Biomedical materials for multi-functional applications · doi:10.1007/978-981-99-6286-0_10
High-temperature Corrosion of Coal-based Thermal Power Plants, Gas Turbines, and Steam Turbines
Kumar, A., Kumar, S., & Singh, R. (2024) · BENTHAM SCIENCE PUBLISHERS eBooks · doi:10.2174/9789815223552124010007
Kong, Y., Ning, H., Shen, Y., Cheng, K., Li, J., Huang, Y., Liu, Q., & Liu, Z. (2025) · Materials Today Communications · doi:10.1016/j.mtcomm.2025.113139
Online monitoring of deposit-induced corrosion in a Waste-to-Energy boiler
Liu, W., Wang, Y., Wang, Y., Liu, Y., Du, A., Ren, Q., Zheng, X., Chen, X., Zhou, M., Wang, Y., et al. (2026) · Waste Management · doi:10.1016/j.wasman.2026.115507
Salsabillah, N., Izzuddin, H., Santjojo, D. J. D. H., Wismogroho, A. S., Sugiarti, E., Jayadi, Widayatno, W. B., Dian, J., & Nugroho, A. (2026) · High Temperature Corrosion of Materials · doi:10.1007/s11085-026-10427-w
Metadata
- Authors
- Mudgal, D., Singh, S., & Prakash, S.
- Affiliations
- Indian Institute of Technology Roorkee (IN)
- Corresponding author
- Mudgal, Deepa
- Venue
- International Journal of Corrosion
- Publisher
- Wiley
- Published
- 2014
- Volume
- 2014
- Pages
- 1-14
- ISSN
- 1687-9325 (ISSN-L)
- 1687-9333
- OpenAlex
- W2044980082
- Semantic Scholar
- 9172decc47a443d3e5202d1876b63e9ec1c502de
- Cited by
- 56
- References
- 100
- Citations by year
- 2026: 5 · 2025: 4 · 2024: 5 · 2023: 3 · 2022: 15 · 2021: 4 · 2020: 8 · 2019: 5 · 2018: 1 · 2017: 2 · 2016: 3
- FWCI
- 2.46
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- International Journal of Corrosion (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Materials Science › Materials Chemistry › Corrosion Behavior and Inhibition
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Keywords
- corrosion, incinerators, biomass boiler, biofuel combustion, municipal solid waste, organic waste, sodium chloride, potassium chloride, corrosion protection
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-27 (prompt extract-v2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.