Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers
Open accessThe DOI matches its Crossref record; 106 of the 106 references it cites were found in a registry or an index; 1 of the 14 sources its claims cite were checked for support.
Abstract
Incinerators are widely used to burn the municipal waste, biowaste, wood, straw, and biomedical waste. Combustion of these types of waste results in generation of chlorides of sodium and potassium which may attack the metallic part of the incinerator. In biofuel-fired boilers, similar type of highly corrosive environment is present. Attempt has been made to review the corrosion problems and their solutions as per the available literature.
Overview
CoChat Summary
TL;DR
This review summarizes high-temperature corrosion problems in incinerators and biomass-fuel-fired boilers, focusing on alkali chlorides and sulphates, active oxidation, and remedial measures such as sulphur additives and thermal-spray coatings. It concludes that chlorine is mainly responsible for damage to protective oxide scales and that coatings and inhibitors can extend component life.
Key findings
- Incineration reduces waste mass by 70% and volume by up to 90% while producing energy, but fireside corrosion causes unforeseen shutdowns; chlorides and sulphates form molten salts on superheater tubes, with NaCl and KCl causing severe corrosion.
- Chlorine/alkali chlorides drive active oxidation, leading to volatile species, porous scale, internal oxidation, and metal loss; Ni-based superalloys resist chloride-containing environments but are susceptible to sulphur-containing environments, while Cr₂O₃-forming alloys are prone to alkaline flux dissolution.
- In Swedish power stations fired with 100% wood-based biofuels, conventional low-chromium ferritic superheater steels had to be replaced after about 20,000 hours if steam temperature was 470°C or higher. Addition of sulphur or sulphur-containing compounds decreased corrosion rate by 50–70%; ammonium sulphate halved the corrosion rate of ferritic/martensitic steels in a wood-fired boiler, and 300 ppm SO₂ drastically reduced corrosion rate.
- D-gun and HVOF sprayed coatings such as 50% Ni-50% Cr, alloy 625, NiCrBSiFe, and alloy 718 performed well; D-gun sprayed 50% Ni-50% Cr in an actual refuse incineration plant operated for about 7 years without problems, and alloy 625, NiCrBSiFe, and alloy 718 performed better than alloy C-276 under simulated biomass combustion conditions.
Methods
- Narrative literature review of corrosion studies in incinerators and biomass-fuel-fired boilers; no original experimental work by the authors is described.
- The review compiles studies on boiler steels, superalloys, and thermal-spray coatings exposed to chloride- and sulphate-containing environments, including NaCl, KCl, Na₂SO₄, V₂O₅, HCl, and SO₂ at various temperatures.
- Main analysis is a qualitative synthesis and tabulation of alloy/coating performance under simulated and actual incinerator/biomass boiler conditions; no systematic search strategy or quantitative meta-analysis is described.
Limitations
- Not stated in the paper: the paper has no explicit limitations section.
- Evident from the text: it is a narrative review without described systematic search, inclusion, or quality-assessment criteria.
- Evident from the text: the summary table is incomplete/fragmented in the provided text, and cited studies use varied environments, temperatures, exposure times, and materials, limiting direct comparability.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 0 Not valid · 13 Not checked · 11 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Normally, incinerators are operated at high temperature between 300 ∘ C and 1100 ∘ C based on volume and type of waste, incinerator, and fuel used [5].”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 1. Introduction
What the sources say
- Partly supportedcites [5] 5. S. W. Manyele and I. S. Kagonji, "Analysis of medical waste incinerator performance based on fuel consumption and cycle times, " Engineering, vol. 4, pp. 625-635, 2012. sourceExperimental — accuracy not yet measured
Section 2.1 describes medical-waste incineration at 850–1000°C and says exhaust gases can reach 1100°C. Section 2.5 gives a typical primary-chamber range of 500–800°C. These passages support high-temperature operation, but not a normal operating range starting at 300°C or the stated dependence of that range on waste volume, waste type, incinerator, and fuel. (LLM, conf=0.85)
- Partly supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“From table it can be seen that NaCl will lead to severe corrosion.Alloy steels and superalloys are resistant to sulphates environment but addition of chlorides increases the corrosion rate manifolds.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 6. Discussion
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Active oxidation is the main mechanism for the corrosion in chlorides environment leading to mass loss due to formation of volatile species, formation of porous scale, and internal oxidation.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 6. Discussion
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“(3) Researchers showed that presence of chlorine in environment is mainly responsible for the damage of protective oxide.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 7. Conclusions
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“(5) Coating can be sprayed using different thermal spray technique which can save the material from direct contact with the salt and hence enhance the life.Already, D-gun and HVOF sprayed coatings such as 50% Ni-50% Cr, alloy 625, NiCrBSiFe, and alloy 718 have been tried in simulated refuse incinerator and biomass-fuel-fired boiler environment and had shown good performance.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 7. Conclusions
20 more claims
Create a free account to see all 25 claims and every source verdict.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > 2. High Temperature Corrosion Problem in Incinerator
“Miller and Krause [18] found that accumulation of elements such as sulphur, chlorine, zinc, aluminium, potassium, and occasionally lead and copper occurred at the metal/scale interface as a deposit in municipal incinerators.”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > References
“18. W. Ma and S. Rotter, "Overview on the chlorine origin of MSW and Cl-originated corrosion during MSW & RDF combustion process, "”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > Biofuel Boiler
“Low alloyed ferritic steel EN1.7380 [Fe-2.25Cr-1Mo]”
§ Corrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers > Biofuel Boiler
“the austenitic EN1.7380 [Fe-18Cr-9Ni]”
Citations
Cites
Production of first and second generation biofuels: A comprehensive review
Naik, S. N., Goud, V. V., Rout, P. K., & Dalai, A. K. (2010) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2009.10.003 · Cited by 3,264
Biomass combustion in fluidized bed boilers: Potential problems and remedies
Khan, A. A., de Jong, W., Jansens, P. J., & Spliethoff, H. (2009) · Fuel Processing Technology · doi:10.1016/j.fuproc.2008.07.012 · Cited by 1,122
The implications of chlorine-associated corrosion on the operation of biomass-fired boilers
Nielsen, H. P., Frandsen, F. J., Dam-Johansen, K., & Baxter, L. L. (2000) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(00)00003-4 · Cited by 785
Biomass-coal co-combustion: opportunity for affordable renewable energy
Baxter, L. (2005) · Fuel · doi:10.1016/j.fuel.2004.09.023 · Cited by 588 · cited 1×
“Apart from these benefits some technical issues associated with cofiring include fuel supply, handling and storage challenges, potential increase in corrosion, decrease in overall efficiency, ash deposition issues, pollutant emissions, carbon burnout impacts on ash marketing, impacts on selective catalytic reduction (…”
BackgroundGrabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Zahs, A., Spiegel, M., & Grabke, H. J. (2000) · Corrosion Science · doi:10.1016/s0010-938x(99)00142-0 · Cited by 365
High temperature corrosion of coatings and boiler steels below chlorine-containing salt deposits
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. A. (2004) · Corrosion Science · doi:10.1016/j.corsci.2003.09.026 · Cited by 260
High-Temperature Corrosion in Waste-to-Energy Boilers
Lee, S.-H., Themelis, N. J., & Castaldi, M. J. (2007) · Journal of Thermal Spray Technology · doi:10.1007/s11666-006-9005-4 · Cited by 178
Ishitsuka, T., & Nose, K. (2002) · Corrosion Science · doi:10.1016/s0010-938x(01)00059-2 · Cited by 177
A review on biomass classification and composition, co-firing issues and pretreatment methods
Tumuluru, J. S., Wright, C. T., Boardman, R. D., Yancey, N. A., & Sokhansanj, S. (2011) · 2011 Louisville, Kentucky, August 7 - August 10, 2011 · doi:10.13031/2013.37191 · Cited by 158 · cited 1×
“It is found that there is a growing interest in the use of biofuels for energy purposes due to various reasons such as reduction in dependency on imported oil, generation of 20 times more employment, mitigation of greenhouse gases [38–40], and reduction of acid rain [41].”
BackgroundRole of chlorides in hot corrosion of a cast Fe–Cr–Ni alloy. Part I: Experimental studies
Mohanty, B. P., & Shores, D. A. (2004) · Corrosion Science · doi:10.1016/j.corsci.2004.04.013 · Cited by 148
Gurrappa, I. (2001) · Surface and Coatings Technology · doi:10.1016/s0257-8972(00)01156-7 · Cited by 143 · cited 1×
“Presence of trace elements in the coating reduces coating life significantly [99]”
BackgroundHigh temperature corrosion of coatings and boiler steels in oxidizing chlorine-containing atmosphere
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. (2003) · Materials Science and Engineering A · doi:10.1016/s0921-5093(02)00537-3 · Cited by 140
Jiang, S. M., Li, H. Q., Ma, J., Xu, C. Z., Gong, J., & Sun, C. (2010) · Corrosion Science · doi:10.1016/j.corsci.2010.03.032 · Cited by 138
The role of chlorine in high temperature corrosion in waste-to-energy plants
Sorell, G. (1997) · Materials at High Temperatures · doi:10.1080/09603409.1997.11689546 · Cited by 136
The hot corrosion of 310 stainless steel with pre-coated NaCl/Na2SO4 mixtures at 750°C
Tsaur, C.-C., Rock, J. C., Wang, C.-J., & Su, Y.-H. (2005) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2004.10.002 · Cited by 133
Bao, Z., Wang, Q. M., Li, W., Liu, X., Gong, J., Xiong, T., & Sun, C. (2009) · Corrosion Science · doi:10.1016/j.corsci.2009.01.003 · Cited by 129
Kamal, S., Jayaganthan, R., & Prakash, S. (2008) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2008.09.031 · Cited by 125
Self-citationAlkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl2
Karlsson, S., Pettersson, J., Johansson, L. G., & Svensson, J. E. (2012) · Oxidation of Metals · doi:10.1007/s11085-012-9293-7 · Cited by 118
Pettersson, J., Folkeson, N., Johansson, L.-G., & Svensson, J.-E. (2011) · Oxidation of Metals · doi:10.1007/s11085-011-9240-z · Cited by 117
Lab-Scale Investigations of High-Temperature Corrosion Phenomena in Straw-Fired Boilers
Nielsen, H. P., Frandsen, F. J., & Dam-Johansen, K. (1999) · Energy & Fuels · doi:10.1021/ef990001g · Cited by 112
Hot Corrosion Behavior of CM 247 LC Alloy in Na2SO4 and NaCl Environments
Gurrappa, I. (1999) · Oxidation of Metals · doi:10.1023/a:1018831025272 · Cited by 112
Deb, D., Iyer, S. R., & Radhakrishnan, V. M. (1996) · Materials Letters · doi:10.1016/s0167-577x(96)00109-7 · Cited by 110
High temperature corrosion of coatings and boiler steels in reducing chlorine-containing atmosphere
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. (2002) · Surface and Coatings Technology · doi:10.1016/s0257-8972(02)00472-3 · Cited by 108
Comparative evaluation of RDF and MSW incineration
Chang, Y.-H., Chen, W. C., & Chang, N.-B. (1998) · Journal of Hazardous Materials · doi:10.1016/s0304-3894(97)00118-0 · Cited by 107 · cited 1×
“Millions of tons of municipal solid waste (MSW) are produced every year which have been treated using incineration technique which reduces waste mass by 70% and volume by up to 90%, as well as providing energy to generate electricity [11].”
BackgroundEffect of kaolin addition on ash characteristics of palm empty fruit bunch (EFB) upon combustion
Konsomboon, S., Pipatmanomai, S., Madhiyanon, T., & Tia, S. (2010) · Applied Energy · doi:10.1016/j.apenergy.2010.07.008 · Cited by 106
Li, Y. S., Niu, Y., & Wu, W. T. (2003) · Materials Science and Engineering A · doi:10.1016/s0921-5093(02)00386-6 · Cited by 103
High temperature corrosion problems in waste incineration systems
Krause, H. H. (1986) · Journal of Materials for Energy Systems · doi:10.1007/bf02833571 · Cited by 97 · cited 1×
“As waste generation has increased considerably worldwide in the last few decades; the combustion of biomedical waste, municipal solid wastes, and biomasses in fluidizedbed boiler facilities is an attractive solution for both energy production and conservation of land, otherwise wasted in landfills [8, 9].”
BackgroundZheng, L., Maicang, Z., & Jianxin, D. (2010) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2010.11.067 · Cited by 95
Slagging Characteristics on the Superheaters of a 12 MW Biomass-Fired Boiler
Niu, Y., Tan, H., Ma, L., Pourkashanian, M., Liu, Z., Liu, Y., Wang, X., Liu, H., & Xu, T. (2010) · Energy & Fuels · doi:10.1021/ef1008055 · Cited by 92
Reducing superheater corrosion in wood‐fired boilers
Henderson, P., Szakálos, P., Pettersson, R., Andersson, C., & Högberg, J. (2006) · Materials and Corrosion · doi:10.1002/maco.200503899 · Cited by 87
Hot corrosion behavior of boiler tube materials in refuse incineration environment
Yamada, K., Tomono, Y., Morimoto, J., Sasaki, Y., & Ohmori, A. (2002) · Vacuum · doi:10.1016/s0042-207x(01)00468-7 · Cited by 87
The Effect of SO 2 and NaCl on High Temperature Hot Corrosion
McKee, D. W., Shores, D. A., & Luthra, K. L. (1978) · Journal of The Electrochemical Society · doi:10.1149/1.2131463 · Cited by 77
NaCl-induced hot corrosion of Fe–Mn–Al–C alloys
Wang, C.-J., & Chang, Y.-C. (2002) · Materials Chemistry and Physics · doi:10.1016/s0254-0584(01)00515-6 · Cited by 77 · cited 1×
“In hot corrosion with NaCl deposit the addition of chromium reduces the metal loss, but overall resistance was not improved [91]”
BackgroundHot corrosion behaviour of a cobalt-base super-alloy K40S with and without NiCrAlYSi coating
Zhang, K., Liu, M. M., Liu, S. L., Sun, C., & Wang, F. H. (2011) · Corrosion Science · doi:10.1016/j.corsci.2011.02.022 · Cited by 74
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. (2002) · Wear · doi:10.1016/s0043-1648(02)00014-5 · Cited by 73
A study on the hot corrosion behavior of Ti–6Al–4V alloy
Anuwar, M., Jayaganthan, R., Tewari, V. K., et al. (2006) · Materials Letters · doi:10.1016/j.matlet.2006.07.058 · Cited by 69
Pettersson, J., Svensson, J. E., & Johansson, L. G. (2009) · Oxidation of Metals · doi:10.1007/s11085-009-9153-2 · Cited by 65
High temperature corrosion of superalloys in an environment containing both oxygen and chlorine
Oh, J. M., McNallan, M. J., Lai, G. Y., & Rothman, M. F. (1986) · Metallurgical Transactions A · doi:10.1007/bf02661276 · Cited by 64
Pihl, E., Heyne, S., Thunman, H., & Johnsson, F. (2010) · Energy · doi:10.1016/j.energy.2010.06.008 · Cited by 63
Role of chlorides in hot corrosion of a cast Fe–Cr–Ni alloy. Part II: thermochemical model studies
Shores, D. A., & Mohanty, B. P. (2004) · Corrosion Science · doi:10.1016/j.corsci.2004.04.014 · Cited by 60
Hot Corrosion of a Single Crystal Ni-Base Superalloy by Na-Salts at 900°C
Li, M., Sun, X., Hu, W., Guan, H., & Chen, S. (2006) · Oxidation of Metals · doi:10.1007/s11085-006-9004-3 · Cited by 60
High temperature corrosion behaviour of nickel aluminides
Klöwer, J., Brill, U., & Heubner, U. (1999) · Intermetallics · doi:10.1016/s0966-9795(99)00042-4 · Cited by 56
Yuan, L., & Wang, H. M. (2009) · Intermetallics · doi:10.1016/j.intermet.2009.08.004 · Cited by 52
Hot corrosion behaviour of a Ni+CrAlYSiN composite coating in Na2SO4–25wt.% NaCl melt
Zhu, L., Zhu, S., & Wang, F. (2012) · Applied Surface Science · doi:10.1016/j.apsusc.2012.12.012 · Cited by 49
Zhang, C., Peng, X., Zhao, J.-Z., & Wang, F. (2005) · Journal of The Electrochemical Society · doi:10.1149/1.1952667 · Cited by 49
Mechanism of Degradation of Titanium Alloy IMI 834 and Its Protection Under Hot Corrosion Conditions
Gurrappa, I. (2003) · Oxidation of Metals · doi:10.1023/a:1023044111767 · Cited by 46 · cited 1×
“33 IMI 834 Na2SO4, 90% Na2SO4-10% NaCl, Na2SO4 + 5% NaCl + 5% V2O5 at 500, 600, and 700C Significant weight loss was observed with pitting-type corrosion in the presence of NaCl [100]”
Effect of pre-oxidation on the hot corrosion of CoNiCrAlYRe alloy
Chen, L.-C., Zhang, C., & Yang, Z.-G. (2011) · Corrosion Science · doi:10.1016/j.corsci.2010.09.045 · Cited by 44
Corrosion in fire tube boilers of biomass combustion plants
Riedl-Narentenau, R., Dahl, J., Obernberger, I., & Narodoslawsky, M. (1999) · Cited by 40
Guilemany, J. M., Torrell, M., & Miguel, J. R. (2008) · Journal of Thermal Spray Technology · doi:10.1007/s11666-008-9167-3 · Cited by 40
High Temperature Corrosion of Superheater Tubes in Waste Incinerators and Coal-Fired Plants
Weulersse, K., Moulin, G., Billard, P., & Pierotti, G. (2004) · Materials science forum · doi:10.4028/www.scientific.net/msf.461-464.973 · Cited by 39
Fireside Corrosion of Superheater Materials in Coal/Biomass Co-fired Advanced Power Plants
Hussain, T., Syed, A. U., & Simms, N. J. (2013) · Oxidation of Metals · doi:10.1007/s11085-013-9394-y · Cited by 38
Viklund, P., Pettersson, R., Hjörnhede, A., Henderson, P., & Sjövall, P. (2009) · Corrosion Engineering, Science and Technology · doi:10.1179/174327809x419203 · Cited by 37
Nitrous oxide emissions from waste incineration
Svoboda, K., Baxter, D., & Martinec, J. (2006) · Chemical Papers · doi:10.2478/s11696-006-0016-x · Cited by 37
Goyal, G., Singh, H., & Prakash, S. (2008) · Applied Surface Science · doi:10.1016/j.apsusc.2008.04.042 · Cited by 34
Self-citationSingh, H., Gitanjaly, Singh, S., & Prakash, S. (2009) · Applied Surface Science · doi:10.1016/j.apsusc.2009.03.040 · Cited by 33
Self-citationPrescott, R., Stott, F. H., & Elliott, P. (1989) · Oxidation of Metals · doi:10.1007/bf00665491 · Cited by 31
The corrosion of Ni3Al in a combustion gas with and without Na2SO4-NaCl deposits at 600?800�C
Niu, Y., Gesmundo, F., Viani, F., & Wu, W. (1994) · Oxidation of Metals · doi:10.1007/bf01052027 · Cited by 30
Hot Corrosion Behavior of Some Superalloys in a Simulated Incinerator Environment at 900 °C
Mudgal, D., Singh, S. P., & Prakash, S. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0721-x · Cited by 30
Self-citationMa, W., & Rotter, V. S. (2008) · International Conference on Bioinformatics and Biomedical Engineering · doi:10.1109/icbbe.2008.564 · Cited by 29 · cited 1×
“Ma andRotter [19] reported thatmunicipal solid waste maintains a large quantity of chlorine, as one of the free elements that causes high temperature corrosion after fine fly ash particles condense on heat exchanger surfaces.”
BackgroundSingh, H., & Sidhu, T. S. (2013) · Oxidation of Metals · doi:10.1007/s11085-013-9414-y · Cited by 29
High-temperature chloridation of binary FeCr alloys at 1000 °C
Strafford, K. N., Datta, P. K., & Forster, G. (1989) · Materials Science and Engineering A · doi:10.1016/0921-5093(89)90719-3 · Cited by 28
High-Temperature Corrosion of Iron–Chromium Alloys in Oxidizing–Chloridizing Conditions
Stott, F. H., & Shih, C. Y. (2000) · Oxidation of Metals · doi:10.1023/a:1004686417317 · Cited by 28 · cited 1×
“1% Y resulted in marked improvement in corrosion protection by allowing formation of Cr2O3 rich layer [87]”
BackgroundWang, C.-J., & Li, C.-C. (2003) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2003.06.004 · Cited by 25
Inter-phase selective corrosion of γ-TiAl alloy in molten salt environment at high temperature
Zhao, W., Xu, B., Ma, Y., & Gong, S. (2011) · Progress in Natural Science Materials International · doi:10.1016/s1002-0071(12)60064-1 · Cited by 25
Corrosion behaviours of several thermal spray coatings used on boiler tubes at elevated temperatures
Rezakhani, D. (2007) · Anti-Corrosion Methods and Materials · doi:10.1108/00035590710762384 · Cited by 25 · cited 2×
“2 NiCr coatings were also tested in the given condition and the result showed that all the coatings provide good resistance to corrosion and help in increasing the life of both the steels [119].”
BackgroundSuperheater Corrosion In Biomass Boilers: Today's Science and Technology
USDOE Office of Energy Efficiency and Renewable Energy (EERE), & Sharp, W. (2010) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · doi:10.2172/1048711 · Cited by 24 · cited 1×
“These boilers are normally operated solely to generate electricity but can also be operated to simultaneously generate a combination of heat and power [37].”
BackgroundBeladi, H., Zarei‐Hanzaki, A., Kelly, G., et al. (2004) · Materials Science and Technology · doi:10.1179/026708304225010361 · Cited by 22
Otero, E., Pardo, A., Merino, M. C., Utrilla, M. V., Lopez, M. D., & Peso, J. L. D. (1999) · Oxidation of Metals · doi:10.1023/a:1018895312069 · Cited by 21
Analysis of Medical Waste Incinerator Performance Based on Fuel Consumption and Cycle Times
Manyele, S. V. (2012) · Engineering · doi:10.4236/eng.2012.410080 · Cited by 21
Corrosion performance of alumina scales in coal gasification environments
Natesan, K. (1997) · Materials at High Temperatures · doi:10.1080/09603409.1997.11689538 · Cited by 21
KCl-Induced High Temperature Corrosion of the Austenitic Stainless Steel 304L – The Influence of SO2
Karlsson, S., Pettersson, J., Svensson, J. E., & Johansson, L. G. (2011) · Materials Science Forum · doi:10.4028/www.scientific.net/msf.696.224 · Cited by 20
(2006) · African Journal of Physics · doi:10.5897/ijps.9000148 · Cited by 20
Self-citationThe high temperature chloridation of iron, nickel and some iron-nickel model alloys
Strafford, K. N., Datta, P. K., & Forster, G. (1989) · Corrosion Science · doi:10.1016/0010-938x(89)90108-x · Cited by 20
Modeling Approaches to Predict Biomass Co-firing with Pulverized Coal
Belošević, S. (2010) · The Open Thermodynamics Journal · doi:10.2174/1874396x01004010050 · Cited by 20
Influence of hot corrosion on the creep strength of the nickel-base superalloy GH37
Lin, T., Zhang, Y. H., & Yang, H. (1984) · Materials Science and Engineering · doi:10.1016/0025-5416(84)90262-3 · Cited by 19
Waste Biomass as Alternative Bio-Fuel - Co-Firing versus Direct Combustion
Trif-Tordai, G., & Ionel, I. (2011) · Alternative Fuel · doi:10.5772/25030 · Cited by 18
Delay, I., Swithenbank, J., & Argent, B. B. (2001) · Journal of Alloys and Compounds · doi:10.1016/s0925-8388(00)01479-1 · Cited by 17
Wu, Y.-N., Yamaguchi, A., Murakami, H., & Kuroda, S. (2006) · MATERIALS TRANSACTIONS · doi:10.2320/matertrans.47.1918 · Cited by 17 · cited 1×
“50 Platinum-iridium films (Ir = 0; 32; 46; 83; 100 at%) were deposited on the nickel-base single crystal superalloy TMS-82+ through magnetron sputtering 900C with the Na2SO4 + 10% NaCl salt coatings The lowest mass gain was observed for the Pt-46Ir aluminide coating, which formed the dense and continuous protective Al…”
MethodCho, J. H., Kim, T. W., Son, K. S., Yoon, J. H., Kim, H. S., Leisk, G. G., Mitton, D. B., & Latanision, R. M. (2003) · Metals and Materials International · doi:10.1007/bf03027051 · Cited by 16
Belosevic, S. (2010) · The Open Thermodynamics Journal · doi:10.2174/1874396x01004020050 · Cited by 15
Ni, M., Du, Y., Lu, S., Peng, Z., Li, X., Yan, J., & Cen, K. (2013) · Environmental Progress & Sustainable Energy · doi:10.1002/ep.11649 · Cited by 15
Fundamental Studies on Alkali Chloride Induced Corrosion during Combustion of Biomass
Cha, S. C., & Spiegel, M. (2004) · Materials science forum · doi:10.4028/www.scientific.net/msf.461-464.1055 · Cited by 14 · cited 1×
“Alkali chlorides are formed during biomass combustion and transported via aerosols or in the vapour phase within the combustion gas, subsequently depositing on the metallic surface or on the already formed oxide layer [47].”
BackgroundSuperheater Corrosion Produced by Biomass Fuels
Sharp, W. B., Singbeil, D., & Keiser, J. R. (2012) · NACE CORROSION Conference · doi:10.5006/c2012-01308 · Cited by 11
Gond, D., Chawla, V., Puri, D., et al. (2010) · Journal of Minerals and Materials Characterization and Engineering · doi:10.4236/jmmce.2010.97042 · Cited by 10
Self-citationEvaluation of wood residues from Crete as alternative fuels
Vamvuka, D., & Bandelis, G. (2010) · International journal of energy and environment · Cited by 10
Corrosion of Ultimet and 31OSS in a simulated waste incineration environment 750 �C
Jegede, A., Vasantasree, V., & Hocking, M. G. (1995) · Journal of Materials Science Letters · doi:10.1007/bf00258173 · Cited by 9
Slagging Characteristics on the Superheaters of a 12 MW Biomass-Fired Boiler
Niu, Y., Tan, H., Ma, L., Pourkashanian, M. M., Liu, Z., Liu, Y., Wang, X., Liu, H., & Xu, T. (2010) · Energy & Fuels · doi:10.1021/ef1013924 · Cited by 7
Heat recovery—an economic benefit to hazardous waste incineration systems
Santoleri, J. J. (1983) · Journal of Heat Recovery Systems · doi:10.1016/0198-7593(83)90006-1 · Cited by 6 · cited 2×
“Surveys show that most incinerators are operated at incorrect temperature and do not destroy the waste completely due to use of insufficient fuel [14].”
BackgroundReducing High Temperature Corrosion when Burning Waste by Adding Digested Sewage Sludge
Karlsson, S., Åmand, L.-E., & Pettersson, J. (2011) · Chalmers Publication Library (Chalmers University of Technology) · Cited by 6
Feasibility Study for Waste Incinerator Plant for the Production of Electricity in Harare,Zimbabwe
Mbohwa, C., & Zvigumbu, B. (2007) · Advanced materials research · doi:10.4028/www.scientific.net/amr.18-19.509 · Cited by 6
Corrosion of Iron and Four Commercial Steels in a Cl-Containing Oxidizing Atmosphere at 500℃~600℃
Zhang, K., Niu, Y., Zeng, C., et al. (2009) · Journal of Material Science and Technology · Cited by 6
Mudali, U. K., Bhuvaneswaran, N., Shankar, P., et al. (2004) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-004-0088-6 · Cited by 5
Hot Corrosion of Co-based Alloys with 25%NaCl+75%Na 2 SO 4 Coating at 1173 K
Fu, G., Guo, X., Liu, Q., et al. (2013) · High Temperature Materials and Processes · doi:10.1515/htmp-2012-0134 · Cited by 5
Xie, D. B., Zhu, S. L., Dai, W. J., & Wang, F. H. (2007) · Materials science forum · doi:10.4028/www.scientific.net/msf.546-549.1739 · Cited by 3
Deposition and Corrosion Problems of Biomass Fired Boiler
Wang, X., Zhao, X., & Ma, L. (2011) · International Conference on Measuring Technology and Mechatronics Automation (ICMTMA) · doi:10.1109/icmtma.2011.213 · Cited by 3 · cited 1×
“Biomass is a kind of fuel having low density, is bulky, and releases the volatiles [36].”
BackgroundCase Histories on the Use of Nickel Alloys in Municipal and Hazardous Waste Fueled Facilities
Agarwal, D. C., & Großmann, G. (2001) · CORROSION · Cited by 2
Hung, M.-C., Ning, S.-K., & Chou, Y.-H. (2011) · Cited by 2
Hussein, R. M. (2012) · Anbar Journal of Engineering Sciences · Cited by 2
Corrosion Testing of HVOF Coatings in High Temperature Environments for Biomass Applications
Paul, S., & Harvey, M. D. F. (2012) · International Thermal Spray Conference · doi:10.31399/asm.cp.itsc2012p0184 · Cited by 2
Niu, Y., Gesmundo, F., Viani, F., & Wu, W. (1994) · Oxidation of Metals · doi:10.1007/bf01046757 · Cited by 1
Xie, D. B., Zhu, S. L., Dai, W. J., & Wang, F. H. (2007) · Materials science forum · doi:10.4028/0-87849-432-4.1739
Case Histories on the Use of Nickel Alloys in Municipal & Hazardous Waste Fueled Facilities
Agarwal, D. C., & Grossmann, G. K. (2001) · CORROSION 2001 · doi:10.5006/c2001-01177
Wang, C. (2003) · Surface and Coatings Technology · doi:10.1016/s0257-8972(03)00988-5
Feasibility Study for Waste Incinerator Plant for the Production of Electricity in Harare,Zimbabwe
Mbohwa, C., & Zvigumbu, B. (2007) · Advanced Materials Research · doi:10.4028/0-87849-450-2.509
Nitrous Oxide Emissions from Waste Incineration
Svoboda, K., Baxter, D., & Martinec, J. (2006) · ChemInform · doi:10.1002/chin.200629218
Research works printed but not linked: 15
- 2011, International Journal of Geology, Earth and Environment Sciences, 1, 48
- 1999, Oxidation of Metals, 51, 507
- 2001, NKK Technical Review, 38
- 1997, Materials at High Temperatures, 14, 137
- 2004, Materials Science Forum, 461-464, 1055
- 2012, Journal of Achievements in Materials and Manufacturing Engineering, 54, 58
- 2010, International Journal of Energy and Environment, 1, 667
- 2006, International Journal of Physical Sciences, 1, 27
- 1996, Materials Letters, 29, 19
- 2012, Anbar Journal For Engineering Sciences, 12
- 1999, Oxidation of Metals, 51, 353
- 2013, High Temperature Materials and Processes, 323, 317
- 2013, Research Inventy, 2, 31
- 2007, Materials Science Forum, 546-549, 1739
- 1989, Materials Science and Engineering A, 120-121, 61
Cited by
Ma, W., Wenga, T., Frandsen, F. J., Yan, B., & Chen, G. (2020) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2019.100789 · Cited by 275
Sadeghi, E., Markocsan, N., & Joshi, S. V. (2019) · Journal of Thermal Spray Technology · doi:10.1007/s11666-019-00938-1 · Cited by 164
A review of biomass ash related problems: Mechanism, solution, and outlook
Abioye, K. J., Harun, N. Y., Sufian, S., Yusuf, M., Jagaba, A. H., Ekeoma, B. C., Kamyab, H., Sikiru, S., Waqas, S., & Ibrahim, H. (2024) · Journal of the Energy Institute · doi:10.1016/j.joei.2023.101490 · Cited by 135
Ma, Z. G., Knotzer, A., Billanes, J. D., & Jôrgensen, B. N. (2020) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2020.109750 · Cited by 112
Environmental implications of the quality of charcoal briquettes and lump charcoal used for grilling
Jelonek, Z., Drobniak, A., Mastalerz, M., & Jelonek, I. (2020) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2020.141267 · Cited by 79
Metadata
- Authors
- Mudgal, D., Singh, S., & Prakash, S.
- Affiliations
- Indian Institute of Technology Roorkee (IN)
- Corresponding author
- Mudgal, Deepa
- Venue
- International Journal of Corrosion
- Publisher
- Wiley
- Published
- 2014
- Volume
- 2014
- Pages
- 1-14
- ISSN
- 1687-9325 (ISSN-L)
- 1687-9333
- OpenAlex
- W2044980082
- Semantic Scholar
- 9172decc47a443d3e5202d1876b63e9ec1c502de
- Cited by
- 56
- References
- 100
- Citations by year
- 2026: 5 · 2025: 4 · 2024: 5 · 2023: 3 · 2022: 15 · 2021: 4 · 2020: 8 · 2019: 5 · 2018: 1 · 2017: 2 · 2016: 3
- FWCI
- 2.46
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- International Journal of Corrosion (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Materials Science › Materials Chemistry › Corrosion Behavior and Inhibition
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Keywords
- corrosion, incinerators, biomass boiler, biofuel combustion, municipal solid waste, organic waste, sodium chloride, potassium chloride, corrosion protection
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-27 (prompt extract-v2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.