Numerical simulation of ISFET structures for biosensing devices with TCAD tools
Open accessThe DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index; none of the 14 sources its claims cite is checked for support yet.
Abstract
Numerical simulation approach to ISFET structures for BioFET design optimization using Synopsys Sentaurus TCAD.
Overview
CoChat Summary
## TL;DR
The paper presents a TCAD-based numerical simulation framework for ISFET/BioFET biosensors by modeling the electrolyte as an intrinsic semiconductor in Synopsys Sentaurus. The simulations show that current modulation is strongly non-linear, depends on target-charge position, and can be greatly affected by reference-electrode bias.
## Key findings
- In an ISFET pH-sensing simulation, the authors report a sensitivity of about 50 mV/pH in threshold-voltage shift, “in agreement with literature data.”
- For a general BioFET, the paper reports no linear relationship between the number of charges and current modulation; target position matters strongly.
- Charges localized near the source are more effective than those near the drain, and randomly distributed targets are more efficient than locally grouped targets for modulating current.
- Increasing the reference electrode voltage can increase the drain current by around four orders of magnitude; with VREF = 1 V the transistor turns on, and VREF = 2 V enhances the effect further.
## Methods
- The study uses Synopsys Sentaurus TCAD to simulate ISFET/BioFET structures at the device level.
- The electrolyte is modeled by replacing the solution with a custom intrinsic semiconductor, with parameters (including permittivity, refractive index, mobility, and density of states) tuned to mimic water and ionic solutions.
- The authors simulate ISFET transfer/output characteristics and a general BioFET with a p-type low-doped Si substrate, thin SiO2, electrolyte, reference electrode, and localized fixed charges represented by dielectric blocks; they vary pH / ion concentration, target number (from 1 to 10), charge position, and reference voltage.
## Limitations
- The paper states that the results for a general BioFET require simulating many receptor-target combinations, which is described as an “overwhelming computational effort”; they therefore used “a still huge number of several randomly selected sample cases.”
- The text makes evident that the electrolyte representation is an approximation: a real electrolyte is replaced by an intrinsic semiconductor, so the model is not a direct physical simulation of the solution itself.
- The text also makes evident that the paper does not report quantitative validation against experimental data for the general BioFET case beyond stating that some current magnitudes are in agreement with literature.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures














Verification
Claims the paper makes
0 Valid · 0 Not valid · 11 Not checked · 31 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“As an example, the electrical potential distribution along the electrolyte-insulator-semiconductor structure can be evaluated for different molar concentrations of the electrolyte solution (Figure 7).”
§ Numerical simulation of ISFET structures for biosensing devices with TCAD tools > Results > Device simulation of a general BioFET device
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“It should be noted that the order of magnitude of the calculated current for the structure at hand are in agreement with literature data (simulated and measured) related to similar ISFET structures [9].”
§ Numerical simulation of ISFET structures for biosensing devices with TCAD tools > Results > Device simulation of a general BioFET device
What the sources say
- Not checked — no full text of the sourcecites [9] source
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Starting from the lower curve (when no localized charge at all is experienced, i.e. when no reaction has occurred), the current tends to increase with the position of the charged block moving from the source channel region (C1 on) toward the middle between source and drain (C5 on or C6 on), and eventually decreasing when the charge approaches the drain region (C10 on).”
§ Numerical simulation of ISFET structures for biosensing devices with TCAD tools > Results > Device simulation of a general BioFET device
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“As mentioned before, the distribution of the charge has a strong effect on the channel modulation.”
§ Numerical simulation of ISFET structures for biosensing devices with TCAD tools > Results > Device simulation of a general BioFET device
boostedstates a causen = 2- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“If we increase the reference voltage, a marked increase of the current (around four orders of magnitude) has been calculated.”
§ Numerical simulation of ISFET structures for biosensing devices with TCAD tools > Results > Device simulation of a general BioFET device
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
24 more claims
Create a free account to see all 42 claims and every source verdict.
- Probably not a substantial claim. 8
- It may state two separate claims as one. 8
Citations
Cites
Solvent Structure, Dynamics, and Ion Mobility in Aqueous Solutions at 25 °C
Koneshan, S., Rasaiah, J. C., Lynden-Bell, R. M., & Lee, S. H. (1998) · The Journal of Physical Chemistry B · doi:10.1021/jp980642x · Cited by 965 · cited 1×
“88 · 10−4cm2/V · s respectively, to reproduce the behavior of Na and Cl ions in a NaCl solution [16].”
MethodThe Ionization Constant of Water over Wide Ranges of Temperature and Density
Bandura, A. V., & Lvov, S. N. (2006) · Journal of Physical and Chemical Reference Data · doi:10.1063/1.1928231 · Cited by 640
A Neuron-Silicon Junction: A Retzius Cell of the Leech on an Insulated-Gate Field-Effect Transistor
Fromherz, P., Offenhäusser, A., Vetter, T., & Weis, J. (1991) · Science · doi:10.1126/science.1925540 · Cited by 563
An improved electron and hole mobility model for general purpose device simulation
Darwish, M. N., Lentz, J. L., Pinto, M. R., Zeitzoff, P. M., Krutsick, T. J., & Vuong, H. H. (1997) · IEEE Transactions on Electron Devices · doi:10.1109/16.622611 · Cited by 180
Modeling H/sup +/-sensitive FETs with SPICE
(1992) · doi:10.1109/16.127470 · Cited by 117
Cramer, T., Chelli, B., Murgia, M., Barbalinardo, M., Bystrenova, E., de Leeuw, D. M., & Biscarini, F. (2013) · Physical Chemistry Chemical Physics · doi:10.1039/c3cp44251a · Cited by 87
Transistor records of excitable neurons from rat brain
Vassanelli, S., & Fromherz, P. (1998) · Applied Physics A: Materials Science & Processing · doi:10.1007/s003390050695 · Cited by 74 · cited 1×
“It has been already pointed out in the past that ISFET devices can measure the extracellular voltage of a single neuron attached with its cell membrane to the device insulator in an open gate configuration [7, 8, 9].”
BackgroundChung, I.-Y., Jang, H., Lee, J., Moon, H., Seo, S. M., & Kim, D. H. (2012) · Nanotechnology · doi:10.1088/0957-4484/23/6/065202 · Cited by 74
Heitzinger, C., & Klimeck, G. (2007) · Journal of Computational Electronics · doi:10.1007/s10825-006-0139-x · Cited by 56
Neuroelectronic Interfacing: Semiconductor Chips with Ion Channels, Nerve Cells, and Brain
Fromherz, P., Eick, S., & Hofmann, B. (2012) · MPG.PuRe (Max Planck Society) · Cited by 50
Cited by
A TCAD-Based Methodology to Model the Site-Binding Charge at ISFET/Electrolyte Interfaces
Bandiziol, A., Palestri, P., Pittino, F., Esseni, D., & Selmi, L. (2015) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2015.2464251 · Cited by 134
Multiview convolutional neural networks for lung nodule classification
Liu, K., & Kang, G. (2017) · International Journal of Imaging Systems and Technology · doi:10.1002/ima.22206 · Cited by 127
A comprehensive review of FET‐based pH sensors: materials, fabrication technologies, and modeling
Sinha, S., & Pal, T. (2021) · Electrochemical Science Advances · doi:10.1002/elsa.202100147 · Cited by 118
Crossing the Nernst Limit (59 mV/pH) of Sensitivity Through Tunneling Transistor-Based Biosensor
Dwivedi, P., Singh, R. K., & Chauhan, Y. S. (2020) · IEEE Sensors Journal · doi:10.1109/jsen.2020.3025975 · Cited by 68
Yip, S. S. F., Parmar, C., Blezek, D. J., Estépar, R. S. J., Pieper, S., Kim, J., & Aerts, H. J. W. L. (2017) · PLoS ONE · doi:10.1371/journal.pone.0178944 · Cited by 53
Metadata
- Authors
- Passeri, D., Morozzi, A., Kanxheri, K., & Scorzoni, A.
- Affiliations
- University of Perugia (IT)
- Corresponding author
- Passeri, Daniele
- Venue
- BioMedical Engineering OnLine
- Published
- 2015
- Volume
- 14
- Issue
- Suppl 2
- Pages
- S3
- ISSN
- 1475-925X (ISSN-L)
- PMC
- PMC4547192
- OpenAlex
- W1916200669
- Semantic Scholar
- 5182160e50194f75d7ab5f323f30988fd02d402c
- Cited by
- 53
- References
- 16
- Citations by year
- 2026: 3 · 2025: 5 · 2024: 3 · 2023: 5 · 2022: 7 · 2021: 10 · 2020: 3 · 2019: 6 · 2018: 3 · 2017: 5 · 2016: 1 · 2015: 2
- Type
- conference abstract
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- Locations
- BioMedical Engineering OnLine (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Topics
- Physical Sciences › Chemistry › Analytical Chemistry › Analytical Chemistry and Sensors
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Semiconductor Devices and Circuit Design
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Analog and Mixed-Signal Circuit Design
- Keywords
- ion-sensitive field-effect transistor, BioFET, biosensors, electrolyte modeling, electrolyte replacement, charge capture, current modulation, transfer characteristics, electrolyte solutions, device simulation
- MeSH terms
- Models, Theoretical, Time Factors, Transistors, Electronic, Biosensing Techniques, Computer-Aided Design
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Numerical simulation of ISFET structures for biosensing devices with TCAD tools. https://app.cochat.ai/papers/10.1186/1475-925x-14-s2-s3
- The paper
- Passeri, D., Morozzi, A., Kanxheri, K., & Scorzoni, A. (2015). Numerical simulation of ISFET structures for biosensing devices with TCAD tools. BioMedical Engineering OnLine. https://doi.org/10.1186/1475-925x-14-s2-s3
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.