A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency
Open accessThe DOI matches its Crossref record; 339 of the 339 references it cites were found in a registry or an index; 36 of the 372 sources its claims cite were checked for support.
Abstract
Through TG analysis, three main stages of lignin pyrolysis can be obtained, including water evaporation (<200 °C), primary decomposition (at 250–500 °C), and carbonization (>500 °C). Pyrolytic temperature significantly influences phenol generation and char formation.
Overview
CoChat Summary
## TL;DR
This review synthesizes how lignin pyrolysis proceeds in three stages and how temperature, time, lignin type, and functional groups shape gas, phenolic oil, and char formation. It also reviews upgrading routes—especially zeolite catalysis and co-pyrolysis with hydrogen-rich feedstocks—to increase aromatic hydrocarbons and improve oil quality.
## Key findings
- Lignin pyrolysis is described as three stages: initial, primary, and charring; the review states that light gases, phenolic compounds, and char with fused aromatic-ring structures are produced across these stages.
- The paper reports that in the primary stage, phenolic compounds are major products at about 400–600 °C, with a maximum phenolic yield at 450 °C in one cited study.
- In a cited example on catalytic pyrolysis with zeolites, HZSM-5 (25) gave the highest BTX selectivity at 56.56%; another zeolite modification study reports 29.3% MAHs over Co-HZSM-5.
- For other catalysts, the review reports 13.26 wt% MAHs with >98% toluene selectivity and >95% deoxygenation over biomass-Mo2C, and 11.2 wt% AHs with 94% MAHs selectivity over Nb2O5.
- Co-pyrolysis with hydrogen-rich feedstocks is presented as a way to raise aromatic hydrocarbons by increasing the feedstock H/Ceffective ratio and supplying hydrogen radicals; the paper cites improved yields and broader product distributions, including MAHs and PAHs.
## Methods
- Not an experimental paper; this is a review that synthesizes prior studies on lignin pyrolysis, lignin types, catalytic upgrading, and co-pyrolysis.
- The review draws on multiple analytical methods used in the cited literature, including TGA/TG-DTG, FTIR, GC/MS, Py-GC/MS, Raman, and NMR.
- The main analysis is qualitative synthesis of published results, organized around pyrolysis mechanism, influencing factors, catalyst effects, and product upgrading.
## Limitations
- The paper explicitly notes that the high oxygen content, acidity, and corrosiveness of lignin oils mean that further upgrading is necessary.
- It also states that lignin pyrolysis faces challenges because lignin is complex and low-reactivity, and that over 90% of lignin is burned with low efficiency while only 2% is efficiently utilized; this is a limitation of the field as described in the paper.
- The text makes evident, but does not frame as a formal limitation: many reported yields and selectivities come from different cited studies with different feedstocks, reactors, and catalysts, so direct comparison across results is constrained.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Fig. 1 Model lignin structures containing 11 units for A a softwood, B hardwood, and C grass [1]](https://figures.cochat.ai/paper-figures/570c6a555ef34497866f99206db9768d/a-review-on-lignin-pyrolysis-pyrolytic-behavior-mechanism-and-relevant-upgrading-figure-1.jpg)
![Fig. 2 A Composition and structure of lignocellulosic biomass, and possible pyrolysis mechanism of B cellulose, C hemicellulose, and D lignin (Reproduced from Refs. [63, 75] with permission from Elsevier)](https://figures.cochat.ai/paper-figures/66c68f1f7e1c41a19e1e19161edd344a/a-review-on-lignin-pyrolysis-pyrolytic-behavior-mechanism-and-relevant-upgrading-figure-2.jpg)
![Fig. 3 Proposed pyrolytic mechanism of lignin (Reproduced from Ref. [128] with permission from Elsevier)](https://figures.cochat.ai/paper-figures/ceaed1ccd6e846b899da90beb7a63747/a-review-on-lignin-pyrolysis-pyrolytic-behavior-mechanism-and-relevant-upgrading-figure-3.jpg)

![Fig. 5 Proposed reaction pathways for primary stage of lignin pyrolysis (P1: depolymerization and dehydration; P2: side-chain scission and demethylation; P3, P4: depolymerization; P5: demethoxylation; P6: side-chain scission and demethoxylation; P7: fragmentation of lignin side chains; P8: dehydration and fragmentation of carbohydrate) [39]](https://figures.cochat.ai/paper-figures/238196e9f9154460a030722ed1c9ff60/a-review-on-lignin-pyrolysis-pyrolytic-behavior-mechanism-and-relevant-upgrading-figure-5.jpg)
![Fig. 6 A Curve fitting for the first-order Raman spectrum of char obtained at 800 °C, and B relationships between ring condensation degree and pyrolytic temperature (Reproduced from Ref. [40] with permission from Elsevier)](https://figures.cochat.ai/paper-figures/741ba043c1154478a2f33b26f4edb9ae/a-review-on-lignin-pyrolysis-pyrolytic-behavior-mechanism-and-relevant-upgrading-figure-6.jpg)
Verification
Claims the paper makes
30 Valid · 5 Not valid · 199 Not checked · 23 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“the yield of liquid products is proportional to the reaction temperature [157]”
§ A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency > Lignin pyrolysis > Lignin pyrolysis mechanism
What the sources say
- Disputedcites [157] Marathe PS, Westerhof RJM, Kersten SRA. Fast pyrolysis of lignins with different molecular weight: experiments and modelling. Appl Energy. 2019;236:1125–37. sourceExperimental — accuracy not yet measured
Section 5.4 (p. 9) reports that oil yield became constant above 530 °C at 500 Pa and was independent of temperature across the tested range at 10⁵ Pa. Although yield rose over part of the range at 500 Pa, the paper does not support a general proportional relationship between liquid-product yield and reaction temperature. (LLM, conf=0.90)
Checked by a reasoning model — may be wrong.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Lignin is a promising alternative to traditional fossil resources for producing biofuels due to its aromaticity and renewability.”
- Also stated in: § Introduction · plain
“Due to the natural aromatic polystructure, lignin (which can mainly be extracted from softwood, hardwood, and grass, and the model lignin structures is shown in Fig. 1 [1]) has been regarded as a sustainable alternative to fossil-derived resources to provide valuable biochemicals [2–7].”
§ A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency > Abstract
What the sources say
- Not checked — no full text of the sourcecites [2] Sethupathy S, Murillo Morales G, Gao L, Wang H, Yang B, Jiang J, et al. Lignin valorization: status, challenges and opportunities. Bioresour Technol. 2022;347: 126696. source
- Not checked — no full text of the sourcecites [3] Radhika NL, Sachdeva S, Kumar M. Lignin depolymerization and biotransformation to industrially important chemicals/biofuels. Fuel. 2022;312: 122935. source
- Not checked — no full text of the sourcecites [4] Kim HU, Kim JW, Tran NT, Limarta SO, Ha J-M, Park Y-K, et al. Direct conversion of lignin to high-quality biofuels by carbon dioxide-assisted hydrolysis combined with transfer hydrogenolysis over supported ruthenium catalysts. Energy Convers Manag. 2022;261: 115607. source
- Not checked — no full text of the sourcecites [5] Yang L, Zheng T, Huang C, Yao J. Using deep eutectic solvent pretreatment for enhanced enzymatic saccharification and lignin utilization of masson pine. Renew Energy. 2022;195:681–7. source
- Not checked — no full text of the sourcecites [6] Roberto Paz Cedeno F, Belon de Siqueira B, Gabriel Solorzano Chavez E, Ulises Miranda Roldán I, Moreira Ropelato L, Paul Martínez Galán J, et al. Recovery of cellulose and lignin from Eucalyptus by-product and assessment of cellulose enzymatic hydrolysis. Renew Energy. 2022;193:807–20. source
- Partly supportedcites [7] Yuan Y, Jiang B, Chen H, Wu W, Wu S, Jin Y, et al. Recent advances in understanding the effects of lignin structural characteristics on enzymatic hydrolysis. Biotechnol Biofuels. 2021;14(1):205. sourceExperimental — accuracy not yet measured
The Background describes lignin as an aromatic polymer and lignocellulose as a renewable resource used to produce bioethanol in place of fossil fuels. It identifies cellulose and hemicelluloses—not lignin—as the main polysaccharides for biofuel production, and describes lignin as an obstacle to their conversion. The cited paper therefore does not support the claim that lignin itself is a promising biofuel feedstock because of its aromaticity and renewability. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § Introduction · plain
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Recently, catalytic pyrolysis has been applied as an efficient method for improving oil quality and stability via deoxygenation reactions with assistance of suitable catalysts [45, 46].”
§ A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency > Introduction
What the sources say
- Not checked — no full text of the sourcecites [45] Ryu HW, Lee HW, Jae J, Park Y-K. Catalytic pyrolysis of lignin for the production of aromatic hydrocarbons: effect of magnesium oxide catalyst. Energy. 2019;179:669–75. source
- Partly supportedcites [46] Zheng A, Huang Z, Wei G, Zhao K, Jiang L, Zhao Z, et al. Controlling deoxygenation pathways in catalytic fast pyrolysis of biomass and its components by using metal-oxide nanocomposites. iScience. 2020;23(1):100814. sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) describes catalytic fast pyrolysis as a promising way to produce highly deoxygenated molecules and reports that catalytic pyrolysis can reduce the oxygen content of bio-oil. This supports the deoxygenation and oil-quality aspects of the claim, but the paper does not establish improved bio-oil stability; its mention of stability in Limitations of the Study concerns the catalysts, not the oil. (LLM, conf=0.84)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Besides, C–O bonds are the most abundant linkages in native lignin, accounting for two-thirds or more of total linkages [9–12].”
§ A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency > Introduction
What the sources say
- Not checked — no full text of the sourcecites [9] Li C, Zhao X, Wang A, Huber GW, Zhang T. Catalytic transformation of lignin for the production of chemicals and fuels. Chem Rev. 2015;115(21):11559–624. source
- Not checked — no full text of the sourcecites [10] Chakar FS, Ragauskas AJ. Review of current and future softwood kraft lignin process chemistry. Ind Crop Prod. 2004;20(2):131–41. source
- Not checked — no full text of the sourcecites [11] Lin F, Ma Y, Sun Y, Song Z, Men X, Wu Y, et al. Selective hydrodeoxygenation of lignin model compound to renewable fuel precursors using two-dimensional nanosheet Ni/HZ5-NS catalyst. Renew Energy. 2022;189:1278–91. source
- Could not verifycites [12] Umar Y, Velasco O, Abdelaziz OY, Aboelazayem O, Gadalla MA, Hulteberg CP, et al. A renewable lignin-derived bio-oil for boosting the oxidation stability of biodiesel. Renew Energy. 2022;182:867–78. sourceExperimental — accuracy not yet measured
The Introduction (p. 4) describes lignin as an abundant aromatic biopolymer, while the Methods (p. 7) describe its depolymerisation. Neither passage addresses which bonds predominate in native lignin or gives a fraction of total linkages; searches for “linkages,” “two-thirds,” and C–O or ether bonds found no supporting passage in our copy. (LLM, conf=0.77)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
Every source the paper cites for this claim was checked and supports it.
In the paper
“the increasing molecular weight of lignin would decrease the oil yield due to higher yields of gases and solids obtained”
§ A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency > Lignin pyrolysis > Lignin pyrolysis mechanism
What the sources say
- Supportedcites [157] Marathe PS, Westerhof RJM, Kersten SRA. Fast pyrolysis of lignins with different molecular weight: experiments and modelling. Appl Energy. 2019;236:1125–37. source
The Conclusions (p. 11) state that as lignin’s number-average molecular weight increased, oil yield decreased while char and gas yields increased. Section 5.2 (p. 8) also reports the decrease in oil yield at both tested pressures. (LLM, conf=0.94)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
133 more claims · 11 with their cited sources checked
Create a free account to see all 257 claims and every source verdict.
- It may state two separate claims as one. 105
- Probably not a substantial claim. 29
- The quote only partly states this claim. 2
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source doesn’t support the claim as written.
In the citing paper
“Lignin depolymerisation, initiated in the 200-400 • C zone, reached completion within this phase [91].”
From Pilot-Scale Slow Pyrolysis, Post-Heat Treatment, and Self-Heating Performance of Biochar Fuels Derived from Construction, Renovation, and Demolition (CRD) Wood Waste (2026) · cites this paper as [91]
Checked by a reasoning model — may be wrong.
Experimental — accuracy not yet measured
Citations
Cites
Pyrolysis of Wood/Biomass for Bio-oil: A Critical Review
Mohan, D., Pittman, C. U., & Steele, P. H. (2006) · Energy & Fuels · doi:10.1021/ef0502397 · Cited by 5,663
Review of fast pyrolysis of biomass and product upgrading
Bridgwater, A. V. (2012) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2011.01.048 · Cited by 4,856
Dissolution of Cellose with Ionic Liquids
Swatloski, R. P., Spear, S. K., Holbrey, J. D., & Rogers, R. D. (2002) · Journal of the American Chemical Society · doi:10.1021/ja025790m · Cited by 4,728 · cited 1×
“Some ILs have been used as solvents for lignocellulosic biomass pretreatment, such as 1-butyl-3-methylimidazolium chloride ([Bmin][Cl]), 1-hexyl-3-methylimidazolium chloride [Hmin][Cl], 1-octyl-3-methylimidazolium chloride ([Omin][Cl]) [262], 1-ethyl-3-methylimidazolium acetate [Emin][OAc] [263, 264], and 1-butyl-3-me…”
MethodCatalytic Transformation of Lignin for the Production of Chemicals and Fuels
Li, C., Zhao, X., Wang, A., Huber, G. W., & Zhang, T. (2015) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00155 · Cited by 2,951 · cited 2×
“, BDE = 481 kJ/mol), large amounts of methoxylated phenols are generated [9, 164].”
BackgroundChemicals from lignin: an interplay of lignocellulose fractionation, depolymerisation, and upgrading
Schutyser, W., Renders, T., Van den Bosch, S., Koelewijn, S.-F., Beckham, G. T., & Sels, B. F. (2018) · Chemical Society Reviews · doi:10.1039/c7cs00566k · Cited by 2,552
Kan, T., Strezov, V., & Evans, T. J. (2016) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.12.185 · Cited by 2,239 · cited 1×
“Lignocellulosic biomass pyrolysis Background Lignocellulosic biomass is a narrow concept of biomass materials, broadly including forestry/agricultural residues, industrial waste biomass, and grasses [62, 63], which is the most popular material for preparing biofuels [64, 65].”
BackgroundPaving the Way for Lignin Valorisation: Recent Advances in Bioengineering, Biorefining and Catalysis
Rinaldi, R., Jastrzebski, R., Clough, M. T., Ralph, J., Kennema, M., Bruijnincx, P. C. A., & Weckhuysen, B. M. (2016) · Angewandte Chemie International Edition · doi:10.1002/anie.201510351 · Cited by 2,138
A review on pyrolysis of plastic wastes
Anuar Sharuddin, S. D., Abnisa, F., Wan Daud, W. M. A., & Aroua, M. K. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.02.037 · Cited by 2,126
Chemical modification of lignins: Towards biobased polymers
Laurichesse, S., & Avérous, L. (2014) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.11.004 · Cited by 2,058 · cited 1×
“, by adding excessive water in the obtained previous liquid containing hemicellulose and lignin fractions) and collected by centrifugation/filtration, which contains better solubility (in many organic solvents) and higher purity with lower structural modification compared to those of lignin obtained Kraft and soda pro…”
BackgroundCatalytic conversion of lignocellulosic biomass to fine chemicals and fuels
Zhou, C.-H., Xia, X., Lin, C.-X., Tong, D.-S., & Beltramini, J. (2011) · Chemical Society Reviews · doi:10.1039/c1cs15124j · Cited by 1,420 · cited 1×
“Commonly, strategies for lignin conversion to biofuels or biochemicals can be summarized into pyrolysis (thermal and catalytic pyrolysis), hydroprocessing (hydrogenolysis, hydrodeoxygenation, hydrogenation, and integrated hydrogen processing), oxidation (organometallic catalysis, metal-free organocatalytic system, bas…”
Background
Research works printed but not linked: 3
- Ma Z, Sun Q, Ye J, Yao Q, Zhao C. Study on the thermal degradation behaviors and kinetics of alkali lignin for production of phenolic-rich bio-oil using TGA-FTIR and Py-GC/MS. J Anal Appl Pyrol. 2016;117:116–24. · DOI · Paper page
- Brebu M, Vasile C. Thermal degradation of lignin—a review. Cell Chem Technol. 2010;44(9):353–63.
- Yan K, Liu F, Chen Q, Ke M, Huang X, Hu W, et al. Pyrolysis characteristics and kinetics of lignin derived from enzymatic hydrolysis residue of bamboo pretreated with white-rot fungus. Biotechnol Biofuel. 2016;9(1):76. · DOI · Paper page
Cited by
Apaydın Varol, E., & Mutlu, Ü. (2023) · Energies · doi:10.3390/en16093674 · Cited by 361
“Since it is more difficult to break down these aromatic rings during pyrolysis, lignin produces fewer amounts of condensable volatiles, and hence the bio-oil yield is the lowest among the other constituents [43,71].”
BackgroundLignins as Promising Renewable Biopolymers and Bioactive Compounds for High-Performance Materials
Vasile, C., & Baican, M. (2023) · Polymers · doi:10.3390/polym15153177 · Cited by 251
Zhang, Y., Liang, Y., Li, S., Yuan, Y., Zhang, D., Wu, Y., Xie, H., Brindhadevi, K., Pugazhendhi, A., & Xia, C. (2023) · Fuel · doi:10.1016/j.fuel.2023.128461 · Cited by 241
Verdía Barbará, P., Choudhary, H., Nakasu, P. S., Al-Ghatta, A., Han, Y., Hopson, C., Aravena, R. I., Mishra, D. K., Ovejero-Pérez, A., Simmons, B. A., et al. (2025) · Chemical Reviews · doi:10.1021/acs.chemrev.4c00754 · Cited by 181
Brienza, F., Cannella, D., Montesdeoca, D., Cybulska, I., & Debecker, D. P. (2024) · RSC Sustainability · doi:10.1039/d3su00140g · Cited by 172
Metadata
- Authors
- Lu, X., & Gu, X.
- Affiliations
- Nanjing Forestry University (CN)
- Corresponding author
- Gu, Xiaoli
- ORCID
- Venue
- Biotechnology for Biofuels and Bioproducts
- Published
- 2022-10-11
- Volume
- 15
- Issue
- 1
- Pages
- 106-106
- ISSN
- 2731-3654 (ISSN-L)
- PMC
- PMC9552425
- OpenAlex
- W4304175550
- Semantic Scholar
- 71ab39e6ab57d4e834bf76bbbc96d80fcbbbbfe8
- Cited by
- 354
- References
- 337
- Citations by year
- 2026: 152 · 2025: 114 · 2024: 60 · 2023: 26 · 2022: 2
- FWCI
- 4.50
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- Biotechnology for Biofuels and Bioproducts (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- China Scholarship Council (202108320294)
- National Natural Science Foundation of China (21774059)
- Priority Academic Program Development of Jiangsu Higher Education Institutions
- Topics
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Physical Sciences › Chemical Engineering › Process Chemistry and Technology › Lignin and Wood Chemistry
- Physical Sciences › Energy › Fuel Technology › Coal Properties and Utilization
- Keywords
- lignin pyrolysis, pyrolysis mechanism, lignin valorization, aromatic hydrocarbons, phenolic compounds, demethoxylation, decarboxylation, char formation, co-pyrolysis, pyrolysis temperature, lignin functional groups, biofuel additives, lignin-derived compounds
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-30, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-09-30 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency. https://app.cochat.ai/papers/10.1186/s13068-022-02203-0
- The paper
- Lu, X., & Gu, X. (2022). A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency. Biotechnology for Biofuels and Bioproducts. https://doi.org/10.1186/s13068-022-02203-0
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.