Hydrodynamic force and moment in pure rolling lubricated contacts. Part 1: Line contacts
The DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index.
Abstract
Hydrodynamic rolling force and moments in line contact have been studied in detail using isoviscousrigid (IVR) and elastohydrodynamic (EHL) models. Using fully flooded assumptions, curve-fitted relationships are suggested for calculating the IVR and EHL hydrodynamic rolling force per unit length. At high speed and light load, EHL numerical results converge towards IVR results so that a single curve-fitted relationship has been derived for covering the full range of operating conditions with a rapid transition from IVR to EHL regime of lubrication. Results obtained are often close to published results (especially in the IVR regime). The EHL hydrodynamic rolling force per unit length is found to be load independent, while load exponents ranging from 0.01 to 0.37 can be found in the literature. A single relationship for both lubrication regimes (IVR and EHL) is given for deriving a starvation factor function of the ratio between the film thickness at the inlet meniscus and the fully flooded minimum film thickness. Finally, the calculation of the total power loss per unit length has also been conducted by integrating through the film and along the rolling direction the power loss per unit volume (defined as the product shear stress time shear rate). Results obtained are consistent with the calculation of the rolling force per unit length.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The dimensionless parameters 𝑈 , 𝑊 , and 𝐺 (see Eq. (3)) have been shown time and time again to provide excellent predictive power for the EHL behavior of the contact [43-46][11,47].”
From Enhancing practical modeling: A neural network approach for locally-resolved prediction of elastohydrodynamic line contacts (2024) · cites this paper as [46]
Citations
Cites
Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part III—Fully Flooded Results
Hamrock, B. J., & Dowson, D. (1977) · Journal of Lubrication Technology · doi:10.1115/1.3453074 · Cited by 1,183
Elasto-hydrodynamic lubrication : the fundamentals of roller and gear lubrication
Dowson, D., & Higginson, G. R. (1966) · Pergamon Press eBooks · Cited by 573
Multilevel Methods in Lubrication
Jacobson, B. (2001) · Tribology International · doi:10.1016/s0301-679x(01)00031-7 · Cited by 201
An Engineering Approach to Hertzian Contact Elasticity—Part I
Houpert, L. (2000) · Journal of Tribology · doi:10.1115/1.1308043 · Cited by 132
Self-citationTorque of tapered roller bearings
Zhou, R. S., & Hoeprich, M. R. (1991) · Journal of Tribology · doi:10.1115/1.2920664 · Cited by 127
Ball Bearing and Tapered Roller Bearing Torque: Analytical, Numerical and Experimental Results
Houpert, L. (2002) · Tribology Transactions · doi:10.1080/10402000208982559 · Cited by 126
Self-citationSimple Formulas for Performance Parameters Used in Elastohydrodynamically Lubricated Line Contacts
Pan, P. J., & Hamrock, B. J. (1989) · Journal of Tribology · doi:10.1115/1.3261900 · Cited by 105
The Influence of Fluid Rheology on the Performance of Traction Drives
Tevaarwerk, J. L., & Johnson, K. L. (1979) · Journal of Lubrication Technology · doi:10.1115/1.3453346 · Cited by 104
Elastohydrodynamic Lubrication of Line Contacts
Hamrock, B. J., & Jacobson, B. O. (1984) · A S L E Transactions · doi:10.1080/05698198408981572 · Cited by 85
Simplified Solution for Stresses and Deformations
Hamrock, B. J., & Brewe, D. E. (1983) · Journal of Lubrication Technology · doi:10.1115/1.3254558 · Cited by 84
CAGEDYN: A Contribution to Roller Bearing Dynamic Calculations Part I: Basic Tribology Concepts
Houpert, L. (2009) · Tribology Transactions · doi:10.1080/10402000903132093 · Cited by 73
Self-citationOperating Torque of Tapered Roller Bearings
Witte, D. C. (1973) · A S L E Transactions · doi:10.1080/05698197308982705 · Cited by 61
Goksem, P. G., & Hargreaves, R. A. (1978) · Journal of Lubrication Technology · doi:10.1115/1.3453183 · Cited by 58
Houpert, L. (1987) · Journal of Tribology · doi:10.1115/1.3261367 · Cited by 51
Self-citationHoupert, L. (2009) · Tribology Transactions · doi:10.1080/10402000903132101 · Cited by 48
Self-citationAnalysis of Starvation Effects on Hydrodynamic Lubrication in Nonconforming Contacts
Brewe, D. E., & Hamrock, B. J. (1982) · Journal of Lubrication Technology · doi:10.1115/1.3253237 · Cited by 31
Research works printed but not linked: 7
- Snare B., 1967, SKF Ball Bearing J., 152, 3
- Houpert L., Leenders P. ‘A study of mixed lubrication in modern deep groove ball bearings. In Proceedings of the 11th Leeds-Lyon Symposium on’ Tribology (1984)
- Houpert L., 2010, STLE Tribol. Trans., 531, 1
- Houpert L., 2010, STLE Tribol. Trans., 531, 10
- Dowson D., 1966, Elastohydrodynamic lubrication, the fundamentals of roller and gear lubrication
- Dalmaz G. Le film mince visqueux dans les contacts hertziens en régimes hydrodynamique et élastohydrodynamique (1979) Docteur d'Etat Es Science thesis: INSA-Lyon, no. I-DE-7907.
- Dowson D. ‘Session 3: Hertzian conditions, paper 10, elastohydrodynamics’ Lubrication and wear: fundamentals and applications to design (1968) part 3A, pp. 151–167.
Cited by
Numerical investigation of the air–oil two-phase flow inside an oil-jet lubricated ball bearing
Hu, J., Wu, W., Wu, M., & Yuan, S. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.09.013 · Cited by 112
The influence of the lubricant viscosity on the rolling friction torque
Bălan, M. R. D., Stamate, V. C., Houpert, L., & Olaru, D. N. (2013) · Tribology International · doi:10.1016/j.triboint.2013.11.017 · Cited by 59
Self-citationA Dynamic Analysis of Cage Instability in Ball Bearings
Nogi, T., Maniwa, K., & Matsuoka, N. (2017) · Journal of Tribology · doi:10.1115/1.4036451 · Cited by 58
Friction torque of cylindrical roller thrust bearings lubricated with wind turbine gear oils
Fernandes, C. M. C. G., Martins, R. C., & Seabra, J. (2012) · Tribology International · doi:10.1016/j.triboint.2012.05.030 · Cited by 54
Oh, K.-J., Cao, L., & Chung, S.-C. (2019) · Tribology International · doi:10.1016/j.triboint.2019.105841 · Cited by 52
Metadata
- Authors
- Biboulet, N., & Houpert, L.
- Affiliations
- TIMKEN Europe, Colmar, France
- Venue
- Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology
- Publisher
- SAGE Publications
- Published
- 2010-05-14
- Volume
- 224
- Issue
- 8
- Pages
- 765-775
- ISSN
- 1350-6501 (ISSN-L)
- 2041-305X
- OpenAlex
- W2034493761
- Cited by
- 45
- References
- 16
- Citations by year
- 2026: 3 · 2025: 2 · 2024: 4 · 2023: 5 · 2022: 3 · 2021: 1 · 2020: 2 · 2019: 4 · 2018: 1 · 2017: 2 · 2016: 2 · 2015: 5 · 2014: 3 · 2013: 4 · 2012: 2
- FWCI
- 4.87
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- journals.sagepub.com/page/policies/text-and-data-mining-license (tdm)
- Locations
- Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology (publishedVersion)
- HAL (submittedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanics of Materials › Adhesion, Friction, and Surface Interactions
- Keywords
- hydrodynamic moments, line contact, elastohydrodynamic lubrication, minimum film thickness, power losses, rolling bearings, lubrication regime transition
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.