The DOI matches its Crossref record; 11 of the 11 references it cites were found in a registry or an index.
Heat accumulation during pulsed laser materials processing
Open accessAbstract
Laser materials processing with ultra-short pulses allows very precise and high quality results with a minimum extent of the thermally affected zone. However, with increasing average laser power and repetition rates the so-called heat accumulation effect becomes a considerable issue. The following discussion presents a comprehensive analytical treatment of multi-pulse processing and reveals the basic mechanisms of heat accumulation and its consequence for the resulting processing quality. The theoretical findings can explain the experimental results achieved when drilling microholes in CrNi-steel and for cutting of CFRP. As a consequence of the presented considerations, an estimate for the maximum applicable average power for ultra-shorts pulsed laser materials processing for a given pulse repetition rate is derived.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Ablation of metals by ultrashort laser pulses
Nolte, S., Momma, C., Jacobs, H., Tünnermann, A., Chichkov, B. N., Wellegehausen, B., & Welling, H. (1997) · Journal of the Optical Society of America B · doi:10.1364/josab.14.002716 · Cited by 1,146
Heat accumulation effects in femtosecond laser-written waveguides with variable repetition rate
Eaton, S. M., Zhang, H., Herman, P. R., Yoshino, F., Shah, L., Bovatsek, J., & Arai, A. Y. (2005) · Optics Express · doi:10.1364/opex.13.004708 · Cited by 813
Femtosecond and picosecond laser drilling of metals at high repetition rates and average powers
Ancona, A., Döring, S., Jauregui, C., Röser, F., Limpert, J., Nolte, S., & Tünnermann, A. (2009) · Optics Letters · doi:10.1364/ol.34.003304 · Cited by 222
Thermal properties of carbon fibers at very high temperature
Pradere, C., Batsale, J. C., Goyhénèche, J. M., Pailler, R., & Dilhaire, S. (2009) · Carbon · doi:10.1016/j.carbon.2008.11.015 · Cited by 194
11 kW average output power from a thin-disk multipass amplifier for ultrashort laser pulses
Negel, J.-P., Voss, A., Ahmed, M. A., Bauer, D., Sutter, D., Killi, A., & Graf, T. (2013) · Optics Letters · doi:10.1364/ol.38.005442 · Cited by 192
Self-citationThe thermal conductivity of carbon fibre-reinforced composites
Pilling, M. W., Yates, B., Black, M. A., & Tattersall, P. (1979) · Journal of Materials Science · doi:10.1007/bf00549304 · Cited by 174
Micromachining of bulk glass with bursts of femtosecond laser pulses at variable repetition rates
Gattass, R. R., Cerami, L. R., & Mazur, E. (2006) · Optics Express · doi:10.1364/oe.14.005279 · Cited by 131
Review on laser drilling I. Fundamentals, modeling, and simulation
Schulz, W., Eppelt, U., & Poprawe, R. (2013) · Journal of Laser Applications · doi:10.2351/1.4773837 · Cited by 126
Comparative study of the ablation of materials by femtosecond and pico- or nanosecond laser pulses
Kononenko, T. V., Конов, В. И., Garnov, S. V., Danielius, R. V., Piskarskas, A., Tamošauskas, G., & Dausinger, F. (1999) · Quantum Electronics · doi:10.1070/qe1999v029n08abeh001560 · Cited by 45
Thermal conductivity measurements of some glass fibre- and carbon fibre-reinforced plastics
McIvor, S. D., Darby, M. I., Wostenholm, G. H., Yates, B., Banfield, L., King, R., & Webb, A. (1990) · Journal of Materials Science · doi:10.1007/bf00587661 · Cited by 45
Cited by
Le, T. D., Phan, H., Kwon, S., Park, S., Jung, Y., Min, J., Chun, B. J., Yoon, H., Ko, S. H., Kim, S., et al. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202205158 · Cited by 433
Heat accumulation in ultra-short pulsed scanning laser ablation of metals
Bauer, F., Michalowski, A., Kiedrowski, T., & Nolte, S. (2015) · Optics Express · doi:10.1364/oe.23.001035 · Cited by 273
Surface Structuring with Ultra-short Laser Pulses: Basics, Limitations and Needs for High Throughput
Neuenschwander, B., Jaeggi, B., Schmid, M., & Hennig, G. (2014) · Physics Procedia · doi:10.1016/j.phpro.2014.08.017 · Cited by 194
Waag, F., Streubel, R., Gökce, B., & Barcikowski, S. (2021) · Applied Nanoscience · doi:10.1007/s13204-021-01693-y · Cited by 67
Ablation target cooling by maximizing the nanoparticle productivity in laser synthesis of colloids
Waag, F., Gökce, B., & Barcikowski, S. (2019) · Applied Surface Science · doi:10.1016/j.apsusc.2018.10.030 · Cited by 19
Metadata
- Authors
- Weber, R., Graf, T., Berger, P., Onuseit, V., Wiedenmann, M., Freitag, C., & Feuer, A.
- Venue
- Optics Express
- Publisher
- Optica Publishing Group
- Published
- 2014-05-02
- Volume
- 22
- Issue
- 9
- Pages
- 11312
- ISSN
- 1094-4087 (ISSN-L)
- OpenAlex
- W1985249131
- Cited by
- 323
- References
- 11
- FWCI
- 13.33
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Heat accumulation during pulsed laser materials processing. https://app.cochat.ai/papers/10.1364/oe.22.011312
- The paper
- Weber, R., Graf, T., Berger, P., Onuseit, V., Wiedenmann, M., Freitag, C., & Feuer, A. (2014). Heat accumulation during pulsed laser materials processing. Optics Express. https://doi.org/10.1364/oe.22.011312
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.