The DOI matches its Crossref record; 32 of the 32 references it cites were found in a registry or an index; none of the 12 sources its claims cite is checked for support yet.
A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities
Open accessAbstract
The current practice for crude oil demulsifier selection consists of pre-screening of the best performing demulsifiers followed by field trials to determine the optimum demulsifier dosage. The method of choice for demulsifier ranking is the bottle test. As there is no standard bottle test method, there are different methodologies reported in the literature. In this work, a new approach to bottle test and field trial was described which improved significantly the selection and dosage of the demulsifier. The bottle test was optimized by measuring an accurate mass of demulsifier. This method produces repeatable results. This bottle-test methodology was benchmarked against field trial results performed in oil processing plants. The field trials were also improved to avoid the accumulation effect of demulsifier, when optimizing their dosage. The field data for the optimization of demulsifier dosage was analyzed mathematically; and a graphical method to determine the optimum range is described.
Overview
CoChat Summary
## TL;DR
This paper proposes a more repeatable bottle-test protocol and an improved field-trial procedure for selecting demulsifiers and optimizing dosage in wet crude oil separation facilities. Using Arabian medium crude oil emulsions, the authors found good agreement between bottle tests and field trials when demulsifier mass was measured accurately and dosage changes were handled to avoid accumulation effects.
## Key findings
- Bottle-test repeatability improved by measuring demulsifier by mass with one-tenth mg accuracy; the paper states this produced repeatable results and achieved a confidence level of 97.5% in repeatability.
- In bottle tests at 30 °C and 50 ppmw, Demulsifiers A and C showed the highest water separation after 60 min and were selected for field testing along with incumbent Demulsifier B.
- For Demulsifier C, bottle tests showed about 10 vol% water separation after 60 min at 50 ppm, while the field trial showed 9–11 vol% water draw-off from Vessel 2 at 42 and 58 ppm, respectively.
- For Demulsifier A, the bottle test gave about 14 vol% water separation after 60 min at 50 ppm, while the field trial gave 13–16 vol% total water draw-off from Vessels 1 and 2 at 45 and 63 ppm, respectively.
- For Demulsifier B, the bottle test gave about 5 vol% water separated after 60 min at 50 ppm, while field trials reported up to 14–16 vol% water draw-off from Vessel 2 at around 36–45 ppm actual dosage.
## Methods
- The study used Arabian medium crude oil emulsions sampled from a Saudi Arabian production facility; the emulsion had 28.8° API gravity, 24 vol% water cut, and SARA composition reported as 30 wt% saturated hydrocarbons, 34 wt% aromatics, 11 wt% resins, and 25 wt% asphaltenes.
- Bottle tests were run in 100-mL glass centrifuge tubes at 30 °C, with demulsifier added by mass using a precision balance; samples were tested within 3 days of sampling, and demulsifiers were used within 1 month of production.
- Field trials were conducted in a real wet crude oil handling train with Vessel 1 and Vessel 2; the main analysis compared water draw-off versus dosage, corrected for dosage/accumulation effects, and fit the dosage-response with a sigmoidal curve to identify minimum, maximum, and most efficient dosages.
## Limitations
- The paper states that no standard bottle test method exists, so results depend on the chosen protocol.
- The authors note bottle tests do not capture production-stream pressure or the geometric and flow conditions of separation vessels; this is a limitation evident from the text.
- The field trials were sensitive to process variations such as temperature, wash water rate, interface level, and liquid level; this is stated in the paper and made evident by the need to control or adjust for these factors.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures









Verification
Claims the paper makes
0 Valid · 3 Not valid · 7 Not checked · 91 Own results and interpretations
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“No significant water separation was observed in Vessel 1 during the field trial.”
§ A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities > 4.2.1 Demulsifier B (incumbent demulsifier) field trial
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The Arab medium crude oil is composed of 30 wt% Saturated hydrocarbons, 34 wt% Aromatics, 11 wt% Resins (NSO), and 25 wt% Asphaltenes.”
§ A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities > 2 Materials and methods
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Figure 4 shows that the time-varying profile of the Vessel 2 draw-off remains relatively constant as the demulsifier dosage is decreased in decrements of 10 ppm.”
§ A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities > 4.2.1 Demulsifier B (incumbent demulsifier) field trial
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Demulsifiers A and C show the highest water separation after 60 min and were selected for field-testing along with the incumbent demulsifier (Demulsifier B).”
§ A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities > 4.1 Bottle test results
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A large drop in draw-off occurs from the 30 ppm to 25 ppm target dosage.”
§ A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities > 4.2.1 Demulsifier B (incumbent demulsifier) field trial
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
53 more claims
Create a free account to see all 101 claims and to verify the 4 references still open.
- The quote only partly states this claim. 2
- Probably not a substantial claim. 31
- It may state two separate claims as one. 19
Citations
Cites
Evidence for a Partially Folded Intermediate in α-Synuclein Fibril Formation
Uversky, V. N., Li, J., & Fink, A. L. (2001) · Journal of Biological Chemistry · doi:10.1074/jbc.m010907200 · Cited by 1,096
Demulsification techniques of water-in-oil and oil-in-water emulsions in petroleum industry
Zolfaghari, R., Fakhru’l-Razi, A., Abdullah, L. C., Elnashaie, S. S. E. H., & Pendashteh, A. (2016) · Separation and Purification Technology · doi:10.1016/j.seppur.2016.06.026 · Cited by 733
Crude-Oil Emulsions: A State-Of-The-Art Review
Kokal, S. (2005) · SPE Production & Facilities · doi:10.2118/77497-pa · Cited by 714
Effects of Asphaltene Solvency on Stability of Water-in-Crude-Oil Emulsions
McLean, J. D., & Kilpatrick, P. K. (1997) · Journal of Colloid and Interface Science · doi:10.1006/jcis.1997.4807 · Cited by 599
Water-in-Crude Oil Emulsion Stabilization: Review and Unanswered Questions
Kilpatrick, P. K. (2012) · Energy & Fuels · doi:10.1021/ef3003262 · Cited by 478
Our current understanding of water-in-crude oil emulsions.
Sjöblom, J., Aske, N., Harald Auflem, I., Brandal, Ø., Erik Havre, T., Sæther, Ø., Westvik, A., Eng Johnsen, E., & Kallevik, H. (2003) · Advances in Colloid and Interface Science · doi:10.1016/s0001-8686(02)00066-0 · Cited by 476
Enhanced sedimentation in settling tanks with inclined walls
Acrivos, A., & Herbolzheimer, E. (1979) · Journal of Fluid Mechanics · doi:10.1017/s0022112079000720 · Cited by 208
Water-In-Crude Oil Emulsion Stability And Emulsion Destabilization By Chemical Demulsifiers
Jones, T. J., Neustadter, E. L., & Whittingham, K. P. (1978) · Journal of Canadian Petroleum Technology · doi:10.2118/78-02-08 · Cited by 204
Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
Drews, A. (2008) · ASTM International eBooks · doi:10.1520/mnl10926m · Cited by 154
Bentea, L., Watzky, M. A., & Finke, R. G. (2017) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.6b12021 · Cited by 154
Research works printed but not linked: 4
- Zolfaghari, 2016, Sep. Sci. Technol., 170, 377
- Manning F.S., Thompson R.E. (1995) Dehydration of crude oil, in: Oilfield processing volume two: Crude oil, Penn Well Corporation, Tulsa, Oklahoma, pp. 113–143. ISBN 13: 9780878143542.
- Salam, 2013, J. Pet. Eng., 2013, 1
- Lochner, 1996, J. Lab. Med., 20, 430
Cited by
Amadu, M., & Miadonye, A. (2023) · Processes · doi:10.3390/pr11082470 · Cited by 29
Treatment of water-in-crude oil emulsion driven by SiO2 modified rice bran
Shen, L., Ai, G., Ao, Y., et al. (2021) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2021.127708 · Cited by 25
A low-temperature ionic liquid demulsifier derived from recycled PET waste plastics
Tang, Y., Zhu, M., Chen, J., et al. (2023) · Journal of Molecular Liquids · doi:10.1016/j.molliq.2023.123737 · Cited by 20
Bahú, J. O., Miranda, N. T., Khouri, N. G., Batistella, C. B., Concha, V. O. C., Maciel, M. R. W., Barbosa, M. I. R., & Filho, R. M. (2021) · Journal of Petroleum Science and Engineering · doi:10.1016/j.petrol.2021.110089 · Cited by 18
Rozhkova, Y., LEKOMTSEV, A. V., Lisin, V. I., Poilov, V. Z., Сафиуллина, Е. У., Ефременко, Д. С., Dengaev, A. V., Kang, W., Li, Z., & Yang, H. (2024) · International Journal of Engineering · doi:10.5829/ije.2024.37.05b.09 · Cited by 16
Metadata
- Authors
- Raynel, G., Salomon Marques, D., Al-Khabaz, S., Al-Thabet, M., & Oshinowo, L.
- Affiliations
- Saudi Aramco (Saudi Arabia) (SA)
- Corresponding author
- Raynel, Guillaume
- Venue
- Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Publisher
- EDP Sciences
- Published
- 2021
- Volume
- 76
- Pages
- 19
- ISSN
- 1294-4475 (ISSN-L)
- 1953-8189
- OpenAlex
- W3134578736
- Cited by
- 18
- References
- 31
- Citations by year
- 2026: 1 · 2025: 5 · 2024: 3 · 2023: 5 · 2022: 2 · 2021: 2
- FWCI
- 1.50
- Type
- journal article
- Language
- en
- Open access
- diamond
- doi.org
- Licence
- Locations
- Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles (publishedVersion, cc-by)
- Springer Link (Chiba Institute of Technology) (submittedVersion)
- HAL (submittedVersion, other-oa)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Saudi Aramco
- Topics
- Physical Sciences › Chemistry › Analytical Chemistry › Petroleum Processing and Analysis
- Physical Sciences › Energy › Fuel Technology › Oil and Gas Production Techniques
- Physical Sciences › Engineering › Mechanical Engineering › Lubricants and Their Additives
- Keywords
- demulsifier selection, bottle test, field trials, water-in-oil emulsion separation, accumulation effect
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities. https://app.cochat.ai/papers/10.2516/ogst/2020096
- The paper
- Raynel, G., Salomon Marques, D., Al-Khabaz, S., Al-Thabet, M., & Oshinowo, L. (2021). A new method to select demulsifiers and optimize dosage at wet crude oil separation facilities. Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles. https://doi.org/10.2516/ogst/2020096
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.