Experimental Determination of the Coefficient of Friction on a Screw Joint
Open accessThe DOI matches its Crossref record; 18 of the 18 references it cites were found in a registry or an index.
Abstract
This paper deals with the coefficient of determination of screw connection friction between the thread and the matrix. The coefficient of friction was measured using a laboratory device with an M20 screw connection without any grease and, subsequently, plastic grease was added (CX80 silicone, lithium, and copper grease). When grease is added, the friction in the threads and screw heads is limited and consistently retained. When tightening by torque, which represents the prevailing assembly method in standard screwing practice, only part of the torque is effectively used to create axial force and pre-stress. The rest of the torque is employed in friction suppression between threads and converted into heat. In general, the coefficient of friction depends on diverse factors such as the roughness of the thread surface, the gradient angle of the helix, and the grease properties. The tightening torque represents a primary parameter in the experimental measurements, monitored using a digital torque spanner, and generates an axial force in the screw. Based on the aforementioned parameters, the objective of this paper was to monitor changes in the coefficient of friction between the thread of the screw and the matrix in the case of different grease types. The actual coefficient of friction was calculated through the exponential equation of the torque balance. First measured was the load of the bolted joint without the use of grease, where the average value of the coefficient of friction was 0.44732; this value served as a benchmark for comparison to the measurements with the use of grease. The measurements showed that the value of the friction coefficient was reduced by 30.57% when using lithium grease, by 40.56% when using silicone grease, and by 47.64% when using copper-based grease, making the latter the most suitable for the application. Without appropriate greasing, friction suppression was accompanied by extremely high torques, which resulted in insufficient screw prolongation.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures













Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Its 8 basic parts described in the assembly procedure are sufficient for testing purposes [40].”
From Poka Yoke in Smart Production Systems with Pick-to-Light Implementation to Increase Efficiency (2023) · cites this paper as [40]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Ivanov, V., Pavlenko, I., Liaposhchenko, O., Gusak, O., & Pavlenko, V. (2019) · Wireless Networks · doi:10.1007/s11276-019-02026-2 · Cited by 46
Straka, Ľ., & Hašová, S. (2016) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1177/0954405416667405 · Cited by 37
Conceptual Use of Augmented Reality in the Maintenance of Manufacturing Facilities
Kaščák, J., Husár, J., Knapčíková, L., Trojanowska, J., & Ivanov, V. (2022) · Lecture notes in mechanical engineering · doi:10.1007/978-3-030-99310-8_19 · Cited by 34
Impact of an Excessive Wear of Bearing on the Mechatronic Devices
Čačko, P., Krenický, T., & Dobránsky, J. (2013) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.460.99 · Cited by 31
Kaščak, J., Gašpár, Š., Paško, J., Knapčíková, L., Husár, J., Baron, P., & Török, J. (2021) · Applied Sciences · doi:10.3390/app11072928 · Cited by 31
Buń, P., Trojanowska, J., Ivanov, V., & Pavlenko, I. (2018) · Cited by 28
Straka, Ľ., Piteľ, J., & Čorný, I. (2021) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-021-07313-x · Cited by 26
Coranič, T., Gašpár, Š., & Pasko, J. (2020) · Applied Sciences · doi:10.3390/app11010262 · Cited by 21
Mixed Reality Training in Electrical Equipment Operating Procedures
Buń, P., Gapsa, J., Husár, J., & Kaščák, J. (2022) · Lecture notes in mechanical engineering · doi:10.1007/978-3-030-99310-8_24 · Cited by 17
Estimation of Grey-Box Dynamic Model of 2-DOF Pneumatic Actuator Robotic Arm Using Gravity Tests
Trojanová, M., Čakurda, T., Hošovský, A., & Krenický, T. (2021) · Applied Sciences · doi:10.3390/app11104490 · Cited by 16
Research works printed but not linked: 3
- 7. Appl. Sci. 2022, 12, 11987
- 11. Trojanowska, J.; Paj ąk, E. Using the Theory of Constraints to Production Processes Improvement. In Proceedings of the 7th International Conference of DAAAM Baltic Industrial Engineering, Tallinn, Estonia, 22-24 April 2010; Volume 1, pp. 322-327.
- 18. Straka, L.; Panda, A. Verification of the non-contact method of measuring roughness parameters on surface machined by WEDM technology. Stud. I Mater. 2021, 41, 32-37.
Cited by
Antosz, K., Knapčíková, L., & Husár, J. (2024) · Applied Sciences · doi:10.3390/app142210450 · Cited by 25
“Subsequent research, as exemplified by the works of Adamczak et al. [14] and Ma-scenik et al. [15], elucidates the potential of digitisation, including process simulations, to improve quality control, thus facilitating superior production management and performance forecasting.”
Poka Yoke in Smart Production Systems with Pick-to-Light Implementation to Increase Efficiency
Trojanowska, J., Husár, J., Hrehova, S., & Knapčíková, L. (2023) · Applied Sciences · doi:10.3390/app132111715 · Cited by 23
“The PTL device is already implemented in the investigated process in the second a a .”
MethodChen, J., Dai, Y., Jia, B., Zheng, Y., & Huang, H. (2025) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2025.109344 · Cited by 21
Jovanović, V., Janošević, D., Marinković, D., Petrović, N., & Đokić, R. (2024) · Machines · doi:10.3390/machines12100737 · Cited by 11
The Automated Quality Control of 3D Printing using Technical SMART Device
Duhančík, M., Židek, K., & Husár, J. (2024) · International Carpathian Control Conference · doi:10.1109/iccc62069.2024.10569677 · Cited by 6
“For quality control in the production or processing of materials, various measuring sensors and devices can be employed[13].”
Method
Metadata
- Authors
- Mascenik, J., & Coranic, T.
- Affiliations
- Department of Design and Monitoring of Technical Systems, Faculty of Manufacturing Technologies with a Seat in Presov, Technical University of Kosice, Bayerova 1, 080 01 Presov, Slovakia
- ORCID
- Mascenik, Jozef
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2022-11-23
- Volume
- 12
- Issue
- 23
- Pages
- 11987
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W4310024326
- Semantic Scholar
- 268a3c1ba55524e35f9f8522c9de9bdbad8e34e3
- Cited by
- 13
- References
- 18
- Citations by year
- 2025: 3 · 2024: 4 · 2023: 6
- FWCI
- 1.25
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Slovak Ministry of Education within project KEGA (017TUKE-4/2021, APVV-18-0316)
- Slovak Research and Development Agency (017TUKE-4/2021, APVV-18-0316)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Engineering Structural Analysis Methods
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanical Engineering › Bladed Disk Vibration Dynamics
- Keywords
- friction coefficient, screw joints, threaded connections, bolted joints, lubrication, lubricating greases, torque tightening, axial force, prestressing, silicone grease, lithium grease, friction torque
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Experimental Determination of the Coefficient of Friction on a Screw Joint. https://app.cochat.ai/papers/10.3390/app122311987
- The paper
- Mascenik, J., & Coranic, T. (2022). Experimental Determination of the Coefficient of Friction on a Screw Joint. Applied Sciences. https://doi.org/10.3390/app122311987
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.