The Effect of Biochar on the Properties of Alkali-Activated Slag Pastes
Open accessThe DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.
Abstract
This paper examines the influence of biochar on the properties of alkali-activated slag pastes using two activator solutions, namely NaOH and Na2CO3. The biochar demonstrated different absorption kinetics in the mixture of slag and the two activator solutions. The pastes with biochar showed a delay in the heat flow peak, compared to the pastes without biochar, but the cumulative heat release in these pastes at later hours was increased, compared to the pastes without biochar. It was found that the use of biochar reduced autogenous shrinkage in the pastes and the reduction in autogenous shrinkage was more pronounced in the alkali-activated slag with NaOH, compared to Na2CO3. The void structure of the pastes was investigated using x-ray micro-computed tomography. It was found that refined pore structure due to reduced effective solution/slag in the pastes with biochar was able to compensate for the decreasing effect of biochar voids on compressive strength. The electrical resistivity was shown to be lower in the pastes with biochar.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures











Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Provis, J. L. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.02.009 · Cited by 2,272
The role of inorganic polymer technology in the development of ‘green concrete’
Duxson, P., Provis, J. L., Lukey, G. C., & van Deventer, J. S. J. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.08.018 · Cited by 1,998 · cited 1×
“It is estimated that the production of alkali-activated slag binders encompasses 25–50% less carbon dioxide emissions and 40% less embodied energy, compared to the Portland cement binders [3].”
Roberts, K. G., Gloy, B. A., Joseph, S., Scott, N. R., & Lehmann, J. (2010) · Environmental Science & Technology · doi:10.1021/es902266r · Cited by 1,243 · cited 1×
“It has been estimated that biochar has the potential to lower up to 870 kg of carbon dioxide-equivalent of greenhouse gases per ton of biomass [32].”
Effect of pore size distribution on drying shrinking of alkali-activated slag concrete
Collins, F., & Sanjayan, J. G. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00327-6 · Cited by 720
Sodium silicate-based, alkali-activated slag mortars
Brough, A. R., & Atkinson, A. (2002) · Cement and Concrete Research · doi:10.1016/s0008-8846(02)00717-2 · Cited by 694 · cited 1×
“These peaks are attributed to the formation of the reaction product calcium (sodium)-silicate (aluminate)-hydrate C (N)-S (Al)-H in the pastes [39].”
Influence of activator on the strength and drying shrinkage of alkali-activated slag mortar
Duran Atiş, C., Bilim, C., Çelik, Ö., & Karahan, O. (2009) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.10.011 · Cited by 658
Water-entrained cement-based materials
Jensen, O. M., & Hansen, P. F. (2002) · Cement and Concrete Research · doi:10.1016/s0008-8846(02)00737-8 · Cited by 619 · cited 1×
“In this method, water is gradually released to the interior of the material to maintain high relative humidity to prevent self-desiccation during the hydration process [17–27].”
Internal curing by superabsorbent polymers in ultra-high performance concrete
Justs, J., Wyrzykowski, M., Bajare, D., & Lura, P. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.05.005 · Cited by 602
Resistance of alkali-activated slag concrete to acid attack
Bakharev, T., Sanjayan, J. G., & Cheng, Y.-B. (2003) · Cement and Concrete Research · doi:10.1016/s0008-8846(03)00125-x · Cited by 586 · cited 1×
“Slag is a by-product of the iron ore smelting process and when mixed with alkaline activators, it results in binders with an increased strength [4] and improved resistance to fire and chemical attacks [5,6].”
Drying and autogenous shrinkage of pastes and mortars with activated slag cement
Melo Neto, A. A., Cincotto, M. A., & Repette, W. (2008) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.11.002 · Cited by 578
Bentur, A., Igarashi, S.-I., & Kovler, K. (2001) · Cement and Concrete Research · doi:10.1016/s0008-8846(01)00608-1 · Cited by 510
Shrinkage mechanisms of alkali-activated slag
Ye, H., & Radlińska, A. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.07.001 · Cited by 469 · cited 1×
“Several investigations have been focused on mitigating the autogenous shrinkage in alkali-activated slag materials [9,10,16–18].”
Schröfl, C., Mechtcherine, V., & Gorges, M. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2012.03.011 · Cited by 464 · cited 1×
“A widely used method to measure the absorption of internal curing agents is the teabag test [20,25,33,34].”
Strength, pore structure and permeability of alkali-activated slag mortars
Shi, C. (1996) · Cement and Concrete Research · doi:10.1016/s0008-8846(96)00174-3 · Cited by 379 · cited 1×
“It is documented that alkali-activated slag pastes possess more 2–50 nm mesopores than Portland cement paste; this range of pore sizes is effective in developing the capillary forces that are the cause of autogenous shrinkage in the pastes [11,40,41].”
Palacios, M., & Puertas, F. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.11.021 · Cited by 362 · cited 2×
“In addition, alkali-activated slag binders have been shown in previous investigations to exhibit higher drying shrinkage than Portland cement binders [7,10–15].”
Effect of elevated temperature curing on properties of alkali-activated slag concrete
Bakharev, T., Sanjayan, J. G., & Cheng, Y.-B. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(99)00143-x · Cited by 349 · cited 1×
“In addition, alkali-activated slag binders have been shown in previous investigations to exhibit higher drying shrinkage than Portland cement binders [7,10–15].”
Microcracking and strength development of alkali activated slag concrete
Collins, F., & Sanjayan, J. G. (2001) · Cement and Concrete Composites · doi:10.1016/s0958-9465(01)00003-8 · Cited by 316 · cited 1×
“It is documented that alkali-activated slag pastes possess more 2–50 nm mesopores than Portland cement paste; this range of pore sizes is effective in developing the capillary forces that are the cause of autogenous shrinkage in the pastes [11,40,41].”
Biochar-mortar composite: Manufacturing, evaluation of physical properties and economic viability
Gupta, S., Kua, H. W., & Pang, S. D. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.02.104 · Cited by 308 · cited 1×
“using optimum conditions can have the filler effect and result in improved hydration in Portland cement binders due to the nucleation effect of fine biochar particles [31].”
Gupta, S., & Kua, H. W. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.10.095 · Cited by 307 · cited 4×
“It is important to note that pores on biochar surface act as channels to smaller pores, which have an important role to play in water absorption and water retention [29,30].”
InfluentialDixit, A., Gupta, S., Pang, S. D., & Kua, H. W. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.117876 · Cited by 303 · cited 3×
“It has also been suggested that the use of biochar in construction materials could be a viable means of reducing waste and sequestering carbon in the built environment [28].”
Neithalath, N., Weiss, J., & Olek, J. (2006) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.09.001 · Cited by 287 · cited 3×
“The EIS measurement was conducted using a Gamry Reference 600 potentiostat/galvanostat (Gamry, Warminster, PA, USA).”
Understanding the drying shrinkage performance of alkali-activated slag mortars
Ye, H., Cartwright, C., Rajabipour, F., & Radlińska, A. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2016.11.010 · Cited by 287
(2012) · Springer eBooks · doi:10.1007/978-94-007-2733-5 · Cited by 247
Shrinkage Characteristics of Alkali-Activated Slag Cements
Cartwright, C., Rajabipour, F., & Radlińska, A. (2015) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001058 · Cited by 243 · cited 3×
“In spite of the beneficial features of alkali-activated slag binders, there exist concerns related to the high autogenous shrinkage of these binders, which can result in increased tendency of the binder to cracking [7–9].”
Komnitsas, K., Zaharaki, D., & Perdikatsis, V. (2009) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2008.04.055 · Cited by 223 · cited 2×
“The change in mass in the range below 150 °C is typically due to the evaporation of unbound water [42,43].”
Mechanical Properties of Mortar Containing Bio-Char From Pyrolysis
Choi, W. C., Yun, H. D., & Lee, J. Y. (2012) · Journal of the Korea institute for structural maintenance and inspection · doi:10.11112/jksmi.2012.16.3.067 · Cited by 187 · cited 4×
“It is important to note that pores on biochar surface act as channels to smaller pores, which have an important role to play in water absorption and water retention [29,30].”
InfluentialZhu, Q., Barney, C. W., & Erk, K. A. (2015) · Materials and Structures · doi:10.1617/s11527-014-0308-5 · Cited by 182 · cited 1×
“A widely used method to measure the absorption of internal curing agents is the teabag test [20,25,33,34].”
Song, C., Choi, Y. C., & Choi, S. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.07.007 · Cited by 179 · cited 5×
“Saturated lightweight aggregates [9] and superabsorbent polymers (SAP) [1,18,19] as internal curing agents have been shown to reduce autogenous shrinkage in alkali-activated slag binders.”
InfluentialPraneeth, S., Saavedra, L., Zeng, M., Dubey, B. K., & Sarmah, A. K. (2021) · Science of The Total Environment · doi:10.1016/j.scitotenv.2020.142327 · Cited by 174 · cited 4×
“The peaks at the wavel ngths of approximately 3340, 2855–29 3, 1599, and 1032 cm−1 are attributed to hydroxyl (O-H), aliphatic (C-H), alkene (C=C), and (C-O) groups, respectively [37].”
InfluentialCrack Mitigation in Concrete: Superabsorbent Polymers as Key to Success?
Mignon, A., Snoeck, D., Dubruel, P., Van Vlierberghe, S., & De Belie, N. (2017) · Materials · doi:10.3390/ma10030237 · Cited by 172
Jain, J. A., & Neithalath, N. (2009) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2009.11.010 · Cited by 157 · cited 2×
“The EIS measurement was conducted using a Gamry Reference 600 potentiostat/galvanostat (Gamry, Warminster, PA, USA).”
Mitigation of autogenous shrinkage in alkali activated slag mortars by internal curing
Sakulich, A. R., & Bentz, D. P. (2012) · Materials and Structures · doi:10.1617/s11527-012-9978-z · Cited by 134 · cited 1×
“Saturated lightweight aggregates [9] and superabsorbent polymers (SAP) [1,18,19] as internal curing agents have been shown to reduce autogenous shrinkage in alkali-activated slag binders.”
Internal curing by superabsorbent polymers in alkali-activated slag
Li, Z., Wyrzykowski, M., Dong, H., Granja, J. L., Azenha, M., Lura, P., & Ye, G. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106123 · Cited by 127 · cited 8×
“Saturated lightweight aggregates [9] and superabsorbent polymers (SAP) [1,18,19] as internal curing agents have been shown to reduce autogenous shrinkage in alkali-activated slag binders.”
InfluentialIgarashi, S. (2006) · International RILEM Conference on Volume Changes of Hardening Concrete: Testing and Mitigation · doi:10.1617/2351580052.009 · Cited by 125
Sakulich, A. R., Anderson, E. M., Schauer, C. L., & Barsoum, M. W. (2009) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2009.02.022 · Cited by 122 · cited 1×
“Slag is a by-product of the iron ore smelting process and when mixed with alkaline activators, it results in binders with an increased strength [4] and improved resistance to fire and chemical attacks [5,6].”
Neto, A. A. M., Cincotto, M. A., & Repette, W. L. (2010) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2010.01.004 · Cited by 122
Superabsorbent polymers as internal curing agents in alkali activated slag mortars
Oh, S.-W., & Choi, Y. C. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.10.121 · Cited by 119 · cited 1×
“In this method, water is gradually released to the interior of the material to maintain high relative humidity to prevent self-desiccation during the hydration process [17–27].”
Krafcik, M. J., & Erk, K. A. (2016) · Materials and Structures · doi:10.1617/s11527-016-0823-7 · Cited by 88 · cited 1×
“A widely used method to measure the absorption of internal curing agents is the teabag test [20,25,33,34].”
Chemical and Microstructural Characterization of 20‐Month‐Old Alkali‐Activated Slag Cements
Sakulich, A. R., Miller, S., & Barsoum, M. W. (2010) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2010.03611.x · Cited by 83 · cited 5×
“The change in mass in the range of 150–550 ◦C is attributed to the decomposition of reaction products including C(N)-S(A)-H and hydrotalcite [42].”
InfluentialThe influence of superabsorbent polymer on the properties of alkali-activated slag pastes
Vafaei, B., Farzanian, K., & Ghahremaninezhad, A. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.117525 · Cited by 81 · cited 5×
“Saturated lightweight aggregates [9] and superabsorbent polymers (SAP) [1,18,19] as internal curing agents have been shown to reduce autogenous shrinkage in alkali-activated slag binders.”
InfluentialSelf-citationBehavior of Superabsorbent Polymers in Calcium- and Sodium-Rich Solutions
Siriwatwechakul, W., Siramanont, J., & Vichit‐Vadakan, W. (2012) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0000449 · Cited by 75
Zhong, P., Wang, J., Wang, X., Liu, J., Li, Z., & Zhou, Y. (2020) · Materials · doi:10.3390/ma13215015 · Cited by 17 · cited 1×
“The lower biochar absorption in the slag mixture compared to the solution could be due to the fact that in the slag mixtures, solution is not as freely available for biochar absorption as in the case of solution [38].”
Cited by
A sustainable roadmap for additive manufacturing using geopolymers in construction industry
Raza, M. H., & Zhong, R. Y. (2022) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2022.106592 · Cited by 76
Effective Use of Biochar as an Additive for Alkali-Activated Slag Mortar Production
Egodagamage, H., Yapa, H. D., Buddika, H. A. D. S., Navaratnam, S., & Nguyen, K. T. Q. (2022) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2023.130487 · Cited by 52
Effect of Superabsorbent Polymer Hydrogels in the Advancement of Cementitious Materials– A Review
Sujitha, V. S., Ramesh, B., & Xavier, J. R. (2023) · Journal of Polymers and the Environment · doi:10.1007/s10924-023-02782-5 · Cited by 48
He, W. F., Li, B., Meng, X., & Shen, Q. (2023) · Buildings · doi:10.3390/buildings13030675 · Cited by 50
Thermodynamic Modeling and Experimental Study of Carbonation of Alkali-Activated Slag Cements
Park, S., Lothenbach, B., Jang, J. G., Kim, H.-K., & Lee, N. (2023) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.2c05789 · Cited by 43
Metadata
- Authors
- Prabahar, J., Vafaei, B., Baffoe, E., & Ghahremaninezhad, A.
- Affiliations
- University of Miami (US)
- Corresponding author
- Ghahremaninezhad, Ali
- Venue
- Construction Materials
- Publisher
- MDPI AG
- Published
- 2021-12-23
- Volume
- 2
- Issue
- 1
- Pages
- 1-14
- ISSN
- 2673-7108 (ISSN-L)
- OpenAlex
- W4200451055
- Cited by
- 29
- References
- 42
- Citations by year
- 2026: 6 · 2025: 5 · 2024: 5 · 2023: 7 · 2022: 6
- FWCI
- 2.33
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Construction Materials (publishedVersion, cc-by)
- Funders
- National Science Foundation (1920127)
- Topics
- Physical Sciences › Engineering › Civil and Structural Engineering › Concrete and Cement Materials Research
- Physical Sciences › Engineering › Civil and Structural Engineering › Concrete Properties and Behavior
- Physical Sciences › Engineering › Building and Construction › Materials Engineering and Processing
- Keywords
- biochar, alkali-activated slag, sodium hydroxide activator, sodium carbonate activator, heat release kinetics, autogenous shrinkage, pore structure, compressive strength, electrical resistivity, micro-computed tomography
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.