Solidification of Graphene-Assisted Phase Change Nanocomposites inside a Sphere for Cold Storage Applications
Open accessThe DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
Abstract
In this work, we experimentally investigated the solidification behavior of functionalized graphene-based phase change nanocomposites inside a sphere. The influence of graphene nanoplatelets on thermal transport and rheological characteristics of the such nanocomposites were also discussed. We adopted the covalent functionalization method to prepare highly stable phase change nanocomposites using commercially available phase change material (PCM) OM08 as the host matrix and graphene nanoplatelets (GnPs) with 0.1, 0.3, and 0.5 volume percentage as the nano inclusions. We report a maximum thermal conductivity enhancement of ~102 and ~46% with 0.5 vol% in the solid and liquid states, respectively. Rheological measurements show that the pure PCM shows Newtonian behavior, whereas the inclusion of GnPs leads to the transition to non-Newtonian behavior, especially at lower shear rates. Viscosity of the nanocomposite increases with an increase in the volume fraction of GnP. For 0.5 vol% of GnPs, maximum increase in viscosity was found to be ~37% at a shear rate of 1000 s−1. Time required for complete solidification decreases with the loading of GnPs. Maximum reduction in solidification time with 0.5 vol% of GnPs was ~40% for bath temperature of −10°C.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source says what the claim attributes to it.
In the citing paper
“The thermal conductivity increased greatly with increasing NP volume percentage (102% maximum), with a sharp increase when solidification occurred.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [59]
The cited source says what the claim attributes to it.
In the citing paper
“The solidification time was also shorter with the increase in NPs, up to a 39% reduction [59].”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [59]
The cited source says what the claim attributes to it.
In the citing paper
“The addition of NPs caused the fluid to have non-Newtonian behavior.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [59]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Describing the uncertainties in experimental results
Moffat, R. J. (1988) · Experimental Thermal and Fluid Science · doi:10.1016/0894-1777(88)90043-x · Cited by 9,860
Chemical functionalization of graphene and its applications
Kuila, T., Bose, S., Mishra, A. K., Khanra, P., Kim, N. H., & Lee, J. H. (2012) · Progress in Materials Science · doi:10.1016/j.pmatsci.2012.03.002 · Cited by 1,928
Fan, L.-W., Fang, X., Wang, X., Zeng, Y., Xiao, Y.-Q., Yu, Z.-T., Xu, X., Hu, Y.-C., & Cen, K.-F. (2013) · Applied Energy · doi:10.1016/j.apenergy.2013.04.043 · Cited by 478
Yavari, F., Fard, H. R., Pashayi, K., Reif, J., Zamiri, A., Yu, Z., Ozisik, R., Borca-Tasciuc, T., & Koratkar, N. (2011) · The Journal of Physical Chemistry C · doi:10.1021/jp200838s · Cited by 450
Veerakumar, C., & Sreekumar, A. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2015.12.005 · Cited by 350
Fatty Acids as Phase Change Materials (PCMs) for Thermal Energy Storage: A Review
Rozanna, D., Chuah, T. G., Salmiah, A., Choong, T. S. Y., & Sa'ari, M. (2005) · International Journal of Green Energy · doi:10.1081/ge-200038722 · Cited by 276
Harish, S., Orejon, D., Takata, Y., & Kohno, M. (2015) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2015.01.056 · Cited by 249
Self-citationZheng, R., Gao, J., Wang, J., & Chen, G. (2011) · Nature Communications · doi:10.1038/ncomms1288 · Cited by 245
Li, T., Lee, J.-H., Wang, R., & Kang, Y. T. (2013) · Energy · doi:10.1016/j.energy.2013.04.010 · Cited by 210
Choi, D. H., Lee, J., Hong, H., & Kang, Y. T. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2014.02.004 · Cited by 187
Kumaresan, V., Velraj, R., & Das, S. K. (2012) · Heat and Mass Transfer · doi:10.1007/s00231-012-0980-3 · Cited by 170
Utomo, A. T., Poth, H., Robbins, P. T., & Pacek, A. W. (2012) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2012.08.003 · Cited by 162
Bista, S., Hosseini, S. E., Owens, E., & Phillips, G. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.07.068 · Cited by 154
Role of PCM based nanofluids for energy efficient cool thermal storage system
Kumaresan, V., Chandrasekaran, P., Nanda, M., Maini, A. K., & Velraj, R. (2013) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2013.04.010 · Cited by 151
Parameshwaran, R., Deepak, K., Saravanan, R., & Kalaiselvam, S. (2013) · Applied Energy · doi:10.1016/j.apenergy.2013.11.029 · Cited by 132
Liu, Y., Li, X., Hu, P., & Hu, G. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2014.10.019 · Cited by 117
Performance analysis of a household refrigerator integrating a PCM heat exchanger
Elarem, R., Mellouli, S., Abhilash, E., & Jemni, A. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2017.07.113 · Cited by 117
Comparative assessment of road transport technologies
Štreimikienė, D., Baležentis, T., & Baležentienė, L. (2013) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2012.12.021 · Cited by 108
Sathishkumar, A., Kumaresan, V., & Velraj, R. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.01.014 · Cited by 104
Influence of the stop/start system on CO2 emissions of a diesel vehicle in urban traffic
Fonseca, N., Casanova, J., & Valdés, M. (2011) · Transportation Research Part D: Transport and Environment · doi:10.1016/j.trd.2010.10.001 · Cited by 93
Constrained melting of graphene-based phase change nanocomposites inside a sphere
Prabakaran, R., Kumar, J. P. N., Lal, D. M., Selvam, C., & Harish, S. (2019) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-019-08458-4 · Cited by 80
Self-citationParametric analysis of domestic refrigerators using PCM heat exchanger
Bakhshipour, S., Valipour, M. S., & Pahamli, Y. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2017.07.014 · Cited by 73
Li, W., Wang, Y., & Kong, C.-C. (2015) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2015.09.004 · Cited by 72
Harish, S., Orejón, D., Takata, Y., & Kohno, M. (2014) · Thermochimica Acta · doi:10.1016/j.tca.2014.12.004 · Cited by 71
Self-citationThe thermal performances of a refrigerator incorporating a phase change material
Maiorino, A., Duca, M. G. D., Mota-Babiloni, A., Greco, A., & Aprea, C. (2019) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2019.02.005 · Cited by 70
Chandrasekaran, P., Cheralathan, M., Kumaresan, V., & Velraj, R. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2013.12.017 · Cited by 69
Sharma, A., & Shukla, A. (2015) · Energy and Buildings · doi:10.1016/j.enbuild.2015.04.028 · Cited by 66
Sidney, S., Mohan Lal, D., Selvam, C., & Harish, S. (2019) · Applied Sciences · doi:10.3390/app9061099 · Cited by 38
Self-citationDesign and Testing of a Thermal Storage System for Electric Vehicle Cabin Heating
Wang, M., Wolfe, E., Craig, T., Laclair, T. J., Abdelaziz, O., & Gao, Z. (2016) · SAE Technical Paper Series · doi:10.4271/2016-01-0248 · Cited by 37
Prabakaran, R., Lal, D. M., Arumugam, P., & Kumar, J. K. (2018) · Heat Transfer Engineering · doi:10.1080/01457632.2018.1436663 · Cited by 23
Self-citationExperimental Study on Solidification Behavior of Carbon Nanotube Nanofluid
Mo, S. P., Chen, Y., Yang, J. Y., & Luo, X. (2010) · Advanced materials research · doi:10.4028/www.scientific.net/amr.171-172.333 · Cited by 20
Ji, C., Yu, M., Wang, S., Zhang, B., Cong, X., Yu, F. Y., & Lin, S. (2016) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2016.08.127 · Cited by 15
Influence of the automotive Start/Stop system on noise emission: Experimental study
Ibarra, D., Ramírez-Mendoza, R. A., López-Caudana, E. O., & Bustamante-Bello, R. (2015) · Applied Acoustics · doi:10.1016/j.apacoust.2015.07.003 · Cited by 13
Sidney, S., Lal, D. M., Selvam, C., et al. (2019) · Preprints.org · doi:10.20944/preprints201901.0156.v1 · Cited by 10
Self-citationCold Storage Air Conditioning System for Idle Stop Vehicle
Yamada, A., Nishida, S., Yokoyama, N., Abei, J., Danjo, T., Florida, L., Brodie, B. R., & Nagano, Y. (2013) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2013-01-1287 · Cited by 6
Cited by
Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review
Tofani, K., & Tiari, S. (2021) · Energies · doi:10.3390/en14133821 · Cited by 114
“[59] experimentally investigated the solidification of the fatty acid PCM OM08 with graphene NPs.”
BackgroundInfluentialSivashankar, M., Selvam, C., Manikandan, S., & Harish, S. (2020) · Energy · doi:10.1016/j.energy.2020.118408 · Cited by 114
Self-citationSathishkumar, A., Sundaram, P., Cheralathan, M., & Kumar, P. G. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.110079 · Cited by 88
Dhaidan, N. S., Kokz, S. A., Rashid, F. L., Hussein, A. K., Younis, O., & Al-Mousawi, F. N. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104271 · Cited by 88
Thakur, A. K., Ahmed, M. S., Kang, H., Prabakaran, R., Said, Z., Rahman, S., Sathyamurthy, R., Kim, J., & Hwang, J. (2022) · Advanced Energy Materials · doi:10.1002/aenm.202202944 · Cited by 84
Self-citation
Metadata
- Authors
- Prabakaran, R., Sidney, S., Lal, D. M., Selvam, C., & Harish, S.
- Affiliations
- Anna University, Chennai (IN)
- SRM Institute of Science and Technology (IN)
- International Institute for Carbon-Neutral Energy Research, Kyushu University (JP)
- Corresponding author
- Lal, Dhasan Mohan
- Harish, Sivasankaran
- Venue
- Energies
- Publisher
- MDPI AG
- Published
- 2019-09-09
- Volume
- 12
- Issue
- 18
- Pages
- 3473
- ISSN
- 1996-1073 (ISSN-L)
- OpenAlex
- W2971654736
- Cited by
- 48
- References
- 34
- Citations by year
- 2026: 2 · 2025: 1 · 2024: 6 · 2023: 11 · 2022: 10 · 2021: 9 · 2020: 9
- FWCI
- 3.93
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- Locations
- Energies (publishedVersion, cc-by)
- RePEc: Research Papers in Economics (submittedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Anna University for providing Anna Centenary Research Fellowship (ACRF) ((Ref No.CFR/ACRF/2015/4, Dated 21.01.2015))
- International Institute for Carbon-Neutral Energy Research ((WPI-I2CNER))
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Phase Change Materials Research
- Physical Sciences › Materials Science › Materials Chemistry › Thermal properties of materials
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Keywords
- graphene nanoplatelets, phase change materials, solidification, cold storage, thermal conductivity enhancement, rheology, non-Newtonian flow, viscosity, covalent functionalization, thermal energy storage
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.