The DOI matches its Crossref record; 53 of the 53 references it cites were found in a registry or an index; 2 of the 15 sources its claims cite were checked for support.
Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5
Open accessAbstract
Lichenysin, an amphiphilic biosurfactant with structural and physicochemical properties similar to surfactin, is produced by Bacillus licheniformis. Its low toxicity, good environmental compatibility, solubilization, foaming, emulsification and detergent activities have led to a wide range of applications in agricultural biocontrol, enhanced oil recovery, foaming agents for cosmetics and detergents for household cleaning products. However, despite the extraordinary surface-active properties and potential applications of lichenysin, the number of wild bacteria found so far is relatively low. Low titers and high costs are the main limiting factors for widespread industrial applications. In this study, a factorial design was used to optimize the composition of the medium for the production of lichenysin by Bacillus licheniformis Ali5. Firstly, the solutions of carbon, nitrogen, amino acids, inorganic salts and trace elements in the medium were evaluated in flasks using a single-factor optimization method. Meanwhile, the operating conditions were optimized in the same way. Afterwards, a partial factorial design was used to investigate the effect of six variables (five medium compositions and inoculum size) on lichenysin production. Based on the results obtained, the concentrations of sucrose and ammonium nitrate and the inoculum size were considered to be important for lichenysin production. Subsequently, a full factorial design was used to optimize these three variables. The optimized medium composition were sucrose 19.8 g/L, NH4NO3 3.9 g/L, K2HPO4·3H2O 4.0 g/L, MgSO4·7H2O 0.6 g/L, FeSO4·7H2O 0.1 g/L, CaCl2 0.01 g/L, NaCl 3.0, trace elements 1.2 mL/L. Finally, the titer of lichenysin after fed-batch fermentation reached 1425.85 mg/L, which was approximately 5.5 times higher than the titer of lichenysin from the original medium. Consequently, the method was further demonstrated to be suitable for lichenysin production.
Overview
CoChat Summary
TL;DR
A factorial and response-surface optimization of medium and fed-batch conditions increased lichenysin production by *Bacillus licheniformis* Ali5, reaching 1425.85 mg/L after three fed-batches, about 5.5-fold higher than the original medium. The optimized flask medium gave 315.26 ± 4.79 mg/L lichenysin, close to the model-predicted 320.60 mg/L.
Key findings
- Single-factor screening plus a 2^(6−2) partial factorial design identified sucrose, NH₄NO₃, and inoculum size as significant variables (p < 0.05); lichenysin titers across the 16 partial-factorial trials ranged from 329.72 mg/L to 82.54 mg/L.
- Central composite optimization gave an optimized medium of sucrose 19.8 g/L, NH₄NO₃ 3.9 g/L, K₂HPO₄·3H₂O 4.0 g/L, MgSO₄·7H₂O 0.6 g/L, FeSO₄·7H₂O 0.1 g/L, CaCl₂ 0.01 g/L, NaCl 3.0 g/L, trace elements 1.2 mL/L, inoculum 6.1%, shaker speed 160 rpm, and initial pH 7.0; predicted titer was 320.60 mg/L, and measured titer was 315.26 ± 4.79 mg/L after 48 h, 43.5% higher than the pre-optimization value of 219.72 mg/L, with 98.3% fit.
- In 1 L bioreactor optimization, the highest lichenysin production was 514.55 mg/L after 60 h at 2.0 L/min aeration; stirring speed affected the time to peak, with maximum at 150 rpm at 24 h and at 200, 250, and 300 rpm at 15 h.
- Fed-batch fermentation reached 1425.85 mg/L lichenysin at 24 h after three feedings, approximately 5.5 times the original medium; product yield on sucrose was 0.025 mg/mg before fed-batch and 0.032 mg/mg after, and peak time shortened from 60 h to 24 h.
Methods
- *Bacillus licheniformis* Ali5 (GenBank MN629226), previously screened from soil, was grown in flask single-factor experiments testing carbon sources, nitrogen sources, amino acids, inorganic salts, trace elements, inoculum size, shaker speed, and working volume; lichenysin was quantified by HPLC using a surfactin standard curve (Y = 15.11X + 373.90, R² = 0.99).
- A 2^(6−2) partial factorial design with 16 trials screened six variables; sucrose, NH₄NO₃, and inoculum were then optimized by central composite design with three factors and five levels, using Minitab 19 for quadratic regression and ANOVA (R² = 0.992, adjusted R² = 0.9849, F = 138.53, lack-of-fit p = 0.463).
- A 1 L bioreactor was used to optimize stirring speed (150, 200, 250, 300 rpm) and aeration rate (0.5, 1.0, 1.5, 2.0 L/min) over 72 h with three replications; fed-batch fermentation used feeding at 12, 18, and 24 h with medium B1 at 3.5 mL/min, an initial working volume of 700 mL, sampling every 6 h over a 54 h fermentation.
Limitations
- The paper states that when surface tension was lower than 30 mN/m, the high viscosity of the biosurfactant affected actual dissolved oxygen in the fermentation broth and bacterial growth during fed-batch fermentation, so further research is needed.
- The paper also notes that lichenysin concentration and surface tension at 48 h may not always be an appropriate measure under different test conditions.
- Evident from the text: lichenysin was not commercially available, so surfactin was used as the standard for preliminary quantification because of similar structure and molecular weight; absolute lichenysin titers are therefore indirect.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 0 Not valid · 10 Not checked · 94 Own results and interpretations
None of the sources cited for this claim have been checked yet.
In the paper
“In addition, the production of lichenysin was significantly promoted by the appropriate concentration of NaCl”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.1. Screening of Medium Components and Cultivation Conditions by Single-Factor Method
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In Figure 1c, it was clearly demonstrated that the addition of precursor amino acids required for lichenysin synthesis as organic nitrogen source exhibited different degrees of inhibition of B. licheniformis Ali5 bacterial growth and lichenysin secretion.”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.1. Screening of Medium Components and Cultivation Conditions by Single-Factor Method
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The maximum production of lichenysin was observed when the rotational speed was 160 rpm.”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.1. Screening of Medium Components and Cultivation Conditions by Single-Factor Method
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Therefore, NH 4 NO 3 was considered to be the most influential nitrogen source for lichenysin production.”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.1. Screening of Medium Components and Cultivation Conditions by Single-Factor Method
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“As shown in Figure 1b, the titer of lichenysin was significantly higher than the other four nitrogen sources when ammonium nitrate was used as the sole nitrogen source.”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.1. Screening of Medium Components and Cultivation Conditions by Single-Factor Method
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
60 more claims
Create a free account to see all 106 claims and to verify the 2 references still open.
- Probably not a substantial claim. 9
- It may state two separate claims as one. 32
- The quote only partly states this claim. 2
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.5. Fed-Batch Fermentation and Growth Kinetics
“the titer of lichenysin reached its maximum at 60 h before the fed-batch fermentation and at 24 h after the fed-batch”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.5. Fed-Batch Fermentation and Growth Kinetics
“the optimal time for lichenysin production was reduced from 36 h to 24 h compared to the batch process.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 3.5. Optimization of Stirring Speed and Aeration Rate in 1 L Bioreactor
“the aeration rate (L/min) was set to 0.5, 1.0, 1.5, and 2.0 (L/min).”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.4. Effect of Bioreactor Stirring Speed and Aeration Rate on Lichenysin Production
“At an aeration rate of 0.5 mL/L, lichenysin concentration increased slowly and reached a maximum at 24 h.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 3.2. Single-Factor Optimization of Culture Medium and Cultivation Conditions
“hydrophilic amino acids such as glycine, serine, cysteine, histidine, lysine, glutamate, and glutamine”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 3.2. Single-Factor Optimization of Culture Medium and Cultivation Conditions
“They were in the order of 6.2 g/L, 8.7 g/L, 10 g/L, 4.3 g/L, 6 g/L, 12.2 g/L, 6 g/L, and 4.8 g/L according to the C/N ratio.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 2.1. Screening of Medium Components and Cultivation Conditions by Single-Factor Method
“Y = 15.11X+ 373.90, with a correlation coefficient R 2 = 0.99, where X is the concentration of surfactin (mg/L), and Y is the peak area (mAU*s).”
§ Optimization of Medium Components for Fed-Batch Fermentation Using Central Composite Design to Enhance Lichenysin Production by Bacillus licheniformis Ali5 > 3.8. Determination of the Concentration of the Biosurfactant Lichenysin
“with the sum of peak areas as the horizontal coordinate and the concentration as the vertical coordinate to obtain the linear regression equation”
Citations
Cites
Jahan, R., Bodratti, A. M., Tsianou, M., & Alexandridis, P. (2020) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2019.102061 · Cited by 565
Lipopeptides from Bacillus and Paenibacillus spp.: A Gold Mine of Antibiotic Candidates
Cochrane, S. A., & Vederas, J. C. (2016) · Medicinal Research Reviews · doi:10.1002/med.21321 · Cited by 474
Yakimov, M. M., Timmis, K. N., Wray, V, & Fredrickson, H. L. (1995) · Applied and Environmental Microbiology · doi:10.1128/aem.61.5.1706-1713.1995 · Cited by 462
Johnson, P., Trybala, A., Starov, V., & Pinfield, V. J. (2021) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2020.102340 · Cited by 428
A review on biosurfactants: properties, applications and current developments
Markande, A. R., Patel, D., & Varjani, S. (2021) · Bioresource Technology · doi:10.1016/j.biortech.2021.124963 · Cited by 361
Dynamic measurement of the volumetric oxygen transfer coefficient in fermentation systems
Bandyopadhyay, B., Humphrey, A. E., Taguchi, H., & Govind Rao, I. B. (2009) · Biotechnology and Bioengineering · doi:10.1002/bit.22566 · Cited by 294
Mohanty, S. S., Koul, Y., Varjani, S., Pandey, A., Ngo, H. H., Chang, J.-S., Wong, J. W. C., & Bui, X.-T. (2021) · Microbial Cell Factories · doi:10.1186/s12934-021-01613-3 · Cited by 242
Biosurfactant: Production and Application
Md, F. (2012) · Journal of Petroleum & Environmental Biotechnology · doi:10.4172/2157-7463.1000124 · Cited by 197
Gaur, V. K., Sharma, P., Sirohi, R., Varjani, S., Taherzadeh, M. J., Chang, J.-S., Yong Ng, H., Wong, J. W. C., & Kim, S.-H. (2022) · Bioresource Technology · doi:10.1016/j.biortech.2021.126059 · Cited by 186
Low-cost fermentative medium for biosurfactant production by probiotic bacteria
Rodrigues, L. R., Teixeira, J. A., & Oliveira, R. (2006) · Biochemical Engineering Journal · doi:10.1016/j.bej.2006.09.012 · Cited by 183
Kinetics of lactic acid fermentation on glucose and corn by Lactobacillus amylophilus
Mercier, P., Yerushalmi, L., Rouleau, D., & Dochain, D. (1992) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.280550204 · Cited by 181
Kurstakins: A New Class of Lipopeptides Isolated from Bacillus thuringiensis
Hathout, Y., Ho, Y.-P., Ryzhov, V., Demirev, P., & Fenselau, C. (2000) · Journal of Natural Products · doi:10.1021/np000169q · Cited by 171
Bacteriocin-like substance production by Bacillus licheniformis strain P40
Cladera-Olivera, F., Caron, G. R., & Brandelli, A. (2004) · Letters in Applied Microbiology · doi:10.1111/j.1472-765x.2004.01478.x · Cited by 166
The studies on the oxygen mass transfer coefficient in a bioreactor
Özbek, B., & Gayik, S. (2001) · Process Biochemistry · doi:10.1016/s0032-9592(00)00272-7 · Cited by 163
Potumarthi, R., Ch., S., & Jetty, A. (2007) · Biochemical Engineering Journal · doi:10.1016/j.bej.2006.12.003 · Cited by 137
Giri, S. S., Ryu, E., Sukumaran, V., et al. (2019) · Microbial Pathogenesis · doi:10.1016/j.micpath.2019.04.035 · Cited by 125
Effect of inoculation methods on the composting efficiency of municipal solid wastes
Xi, B.-D., He, X.-S., Wei, Z.-M., Jiang, Y.-H., Li, M.-X., Li, D., Li, Y., & Dang, Q.-L. (2012) · Chemosphere · doi:10.1016/j.chemosphere.2012.04.032 · Cited by 121
Self-citationZhi, Y., Wu, Q., & Xu, Y. (2017) · Bioresource Technology · doi:10.1016/j.biortech.2017.03.090 · Cited by 121
Volumetric oxygen transfer coefficients (kLa) in batch cultivations involving non-Newtonian broths
Junior, A. C. B., Facciotti, M. C. R., & Schmidell, W. (2001) · Biochemical Engineering Journal · doi:10.1016/s1369-703x(01)00092-4 · Cited by 115
Lin, L.-Z., Zheng, Q., Wei, T., Zhang, Z., Zhao, C.-F., Zhong, H., Xu, Q.-Y., Lin, J., & Guo, L. (2020) · Frontiers in Microbiology · doi:10.3389/fmicb.2020.579621 · Cited by 111
Optimizing the production of the biosurfactant lichenysin and its application in biofilm control
Coronel-León, J., Marqués, A. M., Bastida, J., & Manresa, A. (2016) · Journal of Applied Microbiology · doi:10.1111/jam.12992 · Cited by 102
Biosurfactants: A COVID-19 Perspective
Smith, M. L., Gandolfi, S., Coshall, P. M., & Rahman, P. K. S. M. (2020) · Frontiers in Microbiology · doi:10.3389/fmicb.2020.01341 · Cited by 96
Liu, Q., Niu, J., Yu, Y., Wang, C., Lu, S., Zhang, S., Lv, J. S., & Peng, B. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.127193 · Cited by 95
Lichenysin is produced by mostBacillus licheniformisstrains
Madslien, E. H., Rønning, H. T., Lindbäck, T., Hassel, B., Andersson, M. A., & Granum, P. E. (2013) · Journal of Applied Microbiology · doi:10.1111/jam.12299 · Cited by 91
Moutinho, L. F., Moura, F. R., Silvestre, R. C., & Romão‐Dumaresq, A. S. (2020) · Biotechnology Progress · doi:10.1002/btpr.3093 · Cited by 91
Qiu, Y., Xiao, F., Wei, X., Wen, Z., & Chen, S. (2014) · Applied Microbiology and Biotechnology · doi:10.1007/s00253-014-5978-y · Cited by 89
From bumblebee to bioeconomy: Recent developments and perspectives for sophorolipid biosynthesis
Dierickx, S., Castelein, M., Remmery, J., De Clercq, V., Lodens, S., Baccile, N., De Maeseneire, S. L., Roelants, S. L. K. W., & Soetaert, W. K. (2022) · Biotechnology Advances · doi:10.1016/j.biotechadv.2021.107788 · Cited by 88
MM, Y., HL, F., & KN, T. (1996) · Biotechnology and Applied Biochemistry · doi:10.1111/j.1470-8744.1996.tb00358.x · Cited by 80
Shobharani, P., Padmaja, R. J., & Halami, P. M. (2015) · Research in Microbiology · doi:10.1016/j.resmic.2015.06.003 · Cited by 76
C.-H., Z., J.-Y., W., & G.-Y., H. (2002) · Applied Microbiology and Biotechnology · doi:10.1007/s00253-002-1130-5 · Cited by 72
Teixeira Souza, K. S., Gudiña, E. J., Schwan, R. F., Rodrigues, L. R., Dias, D. R., & Teixeira, J. A. (2018) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2017.12.021 · Cited by 72
Joshi, S., Yadav, S., & Desai, A. J. (2008) · Biochemical Engineering Journal · doi:10.1016/j.bej.2008.04.005 · Cited by 66
Ali, N., Wang, F., Xu, B., Safdar, B., Ullah, A., Naveed, M., Wang, C., & Rashid, M. T. (2019) · Molecules · doi:10.3390/molecules24244448 · Cited by 66
Self-citationContinuous production of the lipopeptide biosurfactant of Bacillus licheniformis JF-2
Lin, S. C., Carswell, K. S., Sharma, M. M., & Georgiou, G. (1994) · Applied Microbiology and Biotechnology · doi:10.1007/bf00221219 · Cited by 64
Moshtagh, B., Hawboldt, K., & Zhang, B. (2019) · Environmental Technology · doi:10.1080/09593330.2018.1473502 · Cited by 61
Bench-Scale Production of Biosurfactants and their Potential in Ex-Situ MEOR Application
Joshi, S. J., & Desai, A. J. (2013) · Soil and Sediment Contamination An International Journal · doi:10.1080/15320383.2013.756450 · Cited by 57
Yalçın, H. T., Ergin‐Tepebaşı, G., & Uyar, E. (2018) · Journal of Basic Microbiology · doi:10.1002/jobm.201800126 · Cited by 50
Zhang, R., Wu, Q., Xu, Y., & Qian, M. C. (2014) · Journal of Food Science · doi:10.1111/1750-3841.12650 · Cited by 33
Mnif, I., Ellouze‐Chaâbouni, S., & Ghribi, D. (2012) · Probiotics and Antimicrobial Proteins · doi:10.1007/s12602-012-9113-z · Cited by 33
Determination of power consumption and volumetric oxygen transfer coefficient in bioreactors
Vilaca, P. R., Junior, A. C. B., Facciotti, M. C. R., et al. (2000) · Bioprocess and Biosystems Engineering · doi:10.1007/s004490050730 · Cited by 32
Přenosil, J. E., & Villeneuve, P. E. (1998) · Biotechnology and Bioengineering · doi:10.1002/(sici)1097-0290(19980920)59:6<679::aid-bit4>3.0.co;2-c · Cited by 31
Zhao, F., Wu, Y., Wang, Q., Zheng, M., & Cui, Q. (2021) · Microbial Cell Factories · doi:10.1186/s12934-021-01676-2 · Cited by 28
Zhu, C., Xiao, F., Qiu, Y., Wang, Q., He, Z., & Chen, S. (2017) · Applied Microbiology and Biotechnology · doi:10.1007/s00253-017-8352-z · Cited by 24
Díaz, P., Torres, M. J., Petroselli, G., et al. (2022) · World Journal of Microbiology and Biotechnology · doi:10.1007/s11274-022-03377-3 · Cited by 24
Production of fatty-acyl-glutamate biosurfactant by Bacillus subtilis on soybean co-products
Martı, M. E., Colonna, W. J., Reznik, G. O., Pynn, M., Jarrell, K. A., Lamsal, B. P., & Glatz, C. E. (2014) · Biochemical Engineering Journal · doi:10.1016/j.bej.2014.11.011 · Cited by 23
Measuring k L a with randomly pulsed dynamic method
Gauthier, L., Thibault, J., & LeDuy, A. (1991) · Biotechnology and Bioengineering · doi:10.1002/bit.260370914 · Cited by 21
Distribution and mass transfer of dissolved oxygen in a multi-habitat membrane bioreactor
Tang, B., Qiu, B., Huang, S., Yang, K., Bin, L., Fu, F., & Yang, H. (2015) · Bioresource Technology · doi:10.1016/j.biortech.2015.02.028 · Cited by 20
Ghribi, D., Elleuch, M., Abdelkefi-Mesrati, L., Boukedi, H., & Ellouze‐Chaâbouni, S. (2012) · Journal of Plant Diseases and Protection · doi:10.1007/bf03356415 · Cited by 19
Haddad, N., Gang, H., Liu, J., Mbadinga, S., & Mu, B. (2014) · Protein & Peptide Letters · doi:10.2174/0929866521666140411112458 · Cited by 18
Meng, Y., Zhao, W., You, J. E., Gang, H., Liu, J., Yang, S., Ye, R., & Mu, B. (2016) · Applied Biochemistry and Biotechnology · doi:10.1007/s12010-016-2044-5 · Cited by 17
(1990) · PubMed · Cited by 3
Continuous production of the lipopeptide biosurfactant of Bacillus licheniformis JF-2
Lin, S.-P., Sharma, M. M., Carswell, K. S., et al. (1994) · Applied Microbiology and Biotechnology · doi:10.1007/s002530050144 · Cited by 3
Study on Processing Technology of Instant Salted Soybean Curd Skin
Geng, Z. (2013) · Zhongguo tiaoweipin · Cited by 1
Research works printed but not linked: 1
- Stanbury, P.F., Whitaker, A., and Hall, S.J. (2013). Principles of Fermentation Technology, Elsevier.
Cited by
Development of Foam-Free Biosurfactant Production Processes Using Bacillus licheniformis
Leal, E., Teixeira, J. A., & Gudiña, E. J. (2024) · Fermentation · doi:10.3390/fermentation10070340 · Cited by 15
Characterization and application of Bacillus velezensis D6 co‐producing α‐amylase and protease
Wang, Z., Wang, S., Bai, H., Zhu, L., Yan, H., Peng, L., Wang, Y., Li, H., Song, Y., & Liu, J. (2024) · Journal of the Science of Food and Agriculture · doi:10.1002/jsfa.13786 · Cited by 11
Pang, Z., Zhang, W., Zhang, B., Navaz, S., Wang, F., & Liao, Y. (2025) · Process Biochemistry · doi:10.1016/j.procbio.2025.01.023 · Cited by 9
Self-citationWang, S., Bai, H., Wang, Z., Peng, L., Li, L., Yan, H., Zhu, L., Wang, Y., Shao, J., & Liu, J. (2024) · Food Bioscience · doi:10.1016/j.fbio.2024.105255 · Cited by 5
Sakiyo, J. J., & Németh, Á. (2025) · International Journal of Molecular Sciences · doi:10.3390/ijms262110518 · Cited by 1
Metadata
- Authors
- Pang, Z., Li, Y., Shang, Y., Ali, N., Wang, F., Zhang, D., & Liao, Y.
- Affiliations
- Beijing Technology and Business University (CN)
- Corresponding author
- Wang, Fenghuan
- Venue
- Fermentation
- Publisher
- MDPI AG
- Published
- 2022-12-06
- Volume
- 8
- Issue
- 12
- Pages
- 712
- ISSN
- 2311-5637 (ISSN-L)
- OpenAlex
- W4310803245
- Cited by
- 11
- References
- 53
- Citations by year
- 2026: 5 · 2025: 2 · 2024: 4
- FWCI
- 0.35
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Fermentation (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- National Key R&D Program of China (2021YFC2102800, 32100068)
- National Natural Science Foundation of China (2021YFC2102800, 32100068)
- Topics
- Physical Sciences › Environmental Science › Pollution › Microbial bioremediation and biosurfactants
- Life Sciences › Biochemistry, Genetics and Molecular Biology › Biotechnology › Enzyme Production and Characterization
- Life Sciences › Biochemistry, Genetics and Molecular Biology › Molecular Biology › Microbial Metabolic Engineering and Bioproduction
- Keywords
- lichenysin, Bacillus licheniformis, biosurfactant production, fed-batch fermentation, culture medium optimization, sucrose, ammonium nitrate, inoculum size, central composite design, fermentation optimization
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.