The DOI matches its Crossref record.
On the Anisotropic Mechanical Properties of Selective Laser-Melted Stainless Steel
Open accessAbstract
The thorough description of the peculiarities of additively manufactured (AM) structures represents a current challenge for aspiring freeform fabrication methods, such as selective laser melting (SLM). These methods have an immense advantage in the fast fabrication (no special tooling or moulds required) of components, geometrical flexibility in their design, and efficiency when only small quantities are required. However, designs demand precise knowledge of the material properties, which in the case of additively manufactured structures are anisotropic and, under certain circumstances, inhomogeneous in nature. Furthermore, these characteristics are highly dependent on the fabrication settings. In this study, the anisotropic tensile properties of selective laser-melted stainless steel (1.4404, 316L) are investigated: the Young’s modulus ranged from 148 to 227 GPa, the ultimate tensile strength from 512 to 699 MPa, and the breaking elongation ranged, respectively, from 12% to 43%. The results were compared to related studies in order to classify the influence of the fabrication settings. Furthermore, the influence of the chosen raw material was addressed by comparing deviations on the directional dependencies reasoned from differing microstructural developments during manufacture. Stainless steel was found to possess its maximum strength at a 45° layer versus loading offset, which is precisely where AlSi10Mg was previously reported to be at its weakest.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
An overview of modern metal additive manufacturing technology
Armstrong, M., Mehrabi, H., & Naveed, N. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2022.10.060 · Cited by 549
Narasimharaju, S. R., Zeng, W., See, T. L., Zhu, Z., Scott, P., Jiang, X., & Lou, S. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.12.033 · Cited by 508
Beautiful and Functional: A Review of Biomimetic Design in Additive Manufacturing
du Plessis, A., Broeckhoven, C., Yadroitsava, I., Yadroitsev, I., Hands, C. H., Kunju, R., & Bhate, D. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.03.033 · Cited by 448
Ha, C. S., Yao, D., Xu, Z., Liu, C., Liu, H., Elkins, D., Kile, M., Deshpande, V., Kong, Z., Bauchy, M., et al. (2023) · Nature Communications · doi:10.1038/s41467-023-40854-1 · Cited by 387
Bagherifard, S., Beretta, N., Monti, S., Riccio, M., Bandini, M., & Guagliano, M. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.02.055 · Cited by 327
Metadata
- Authors
- Hitzler, L., Hirsch, J., Heine, B., Merkel, M., Hall, W., & Öchsner, A.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2017-09-26
- Volume
- 10
- Issue
- 10
- Pages
- 1136
- ISSN
- 1996-1944 (ISSN-L)
- OpenAlex
- W2749662039
- Cited by
- 220
- References
- 0
- FWCI
- 17.93
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: On the Anisotropic Mechanical Properties of Selective Laser-Melted Stainless Steel. https://app.cochat.ai/papers/10.3390/ma10101136
- The paper
- Hitzler, L., Hirsch, J., Heine, B., Merkel, M., Hall, W., & Öchsner, A. (2017). On the Anisotropic Mechanical Properties of Selective Laser-Melted Stainless Steel. Materials. https://doi.org/10.3390/ma10101136
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.