Full Parametric Study of the Influence of Ionomer Content, Catalyst Loading and Catalyst Type on Oxygen and Ion Transport in PEM Fuel Cell Catalyst Layers
Open accessThe DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index; 1 of the 2 sources its claims cite were checked for support.
Abstract
This study investigates the influence of ionomer content, catalyst loading and catalyst type on oxygen and ion transport in PEM fuel cell catalyst layers.
Overview
CoChat Summary
## TL;DR
This paper reports a full parametric study of cathode catalyst layers in PEM fuel cells, varying ionomer content, Pt loading, and catalyst type (40 wt.% and 60 wt.% Pt/C) to see how oxygen and ion transport affect performance. The key result is that the optimum ionomer content depends on operating point, humidity, loading, and catalyst type, with thicker/high-loading layers increasingly limited by through-plane diffusion and proton transport.
## Key findings
- The study varied ionomer content from 15 to 50 wt.% in dry layers, corresponding to an I/C ratio of 0.29–1.67, and Pt loading from 0.05–0.8 mg cm−2 for 40 wt.% Pt/C and 60 wt.% Pt/C catalysts.
- SEM/EDX showed no obvious interfaces between printed sublayers and a homogeneous distribution of Pt, C, and F; the authors conclude that electrical and protonic contact is established regardless of printing multiple layers.
- The HFR during polarization curves was in a low and narrow range of 25–35 mOhm cm2, indicating stable production/characterization and little influence from membrane-property variation.
- For the 40 wt.% catalyst, the optimum ionomer content depended on conditions: at low current density the optimum was around I/C = 0.71–1.36 for Pt loadings > 0.3 mg cm−2; at 30% RH the optimum was 1.36, while at 120% RH it was 0.62–1.36. At 300 mV, the optimum Pt loading was around 0.25 mg cm−2; for the 60 wt.% catalyst it was around 0.3 mg cm−2.
- The paper concludes that through-plane diffusion losses become more limiting than proton conductivity at high Pt loading and high ionomer content, and that the general trends are similar for 40 and 60 wt.% Pt/C, though the 60 wt.% catalyst needs less ionomer because its catalyst layer is thinner.
## Methods
- Design: Full parametric study of cathode catalyst layers, varying ionomer content, Pt loading, and catalyst type (40 wt.% Pt/C and 60 wt.% Pt/C) in membrane electrode assemblies.
- Sample/data: Catalyst-coated membranes were made by screen printing; ionomer content was 15–50 wt.% in dry layers, with I/C = 0.29–1.67 and Pt loading = 0.05–0.8 mg cm−2. The authors say they discussed “80+ cells” in the analysis.
- Main analysis: Ex situ SEM/EDX for morphology and layer uniformity; in situ polarization curves, high-frequency resistance (HFR), cyclic voltammetry for ECSA, and humidity sweeps at 1 A/cm2 under varied relative humidity.
## Limitations
- The authors explicitly note that the paper provides a data set as a starting point for further work, and say they plan future studies on graded catalyst layers, limiting current density, impedance spectroscopy, and accelerated stress tests; this indicates the present study does not address those topics.
- The paper states that some comparisons are based on selected points/conditions from the polarization curves and that some data are “not shown” for all ionomer contents; this suggests the reported analysis is not exhaustive for every measured condition.
- The paper does not report a formal statistical uncertainty analysis or error bars for the key optimum values in the provided text, so the strength of those optima is not fully quantified here.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures








Verification
Claims the paper makes
1 Valid · 0 Not valid · 2 Not checked · 57 Own results and interpretations
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“and at around 0.3 mg cm−2 for the 60 wt % catalyst.”
§ Full Parametric Study of the Influence of Ionomer Content, Catalyst Loading and Catalyst Type on Oxygen and Ion Transport in PEM Fuel Cell Catalyst Layers > 3. Results and Discussion > 3.3. In situ Analysis
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“For the same platinum loading, the 60 wt% catalysts are about 33% thinner than the 40 wt% catalyst since mostly the amount of carbon defines the layer thickness.”
§ Full Parametric Study of the Influence of Ionomer Content, Catalyst Loading and Catalyst Type on Oxygen and Ion Transport in PEM Fuel Cell Catalyst Layers > 3. Results and Discussion > 3.3. In situ Analysis
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“This is highlighted in Figure 8c,d, where it can be seen that the cells are more tolerant to low humidity.”
§ Full Parametric Study of the Influence of Ionomer Content, Catalyst Loading and Catalyst Type on Oxygen and Ion Transport in PEM Fuel Cell Catalyst Layers > 3. Results and Discussion > 3.3. In situ Analysis
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In Figure 1d–f, EDX distributions of carbon, fluorine and platinum are shown, where it can be seen that the ionomer, catalyst and support are homogeneously distributed throughout the different layers, regardless of the number of layers used for the production of the catalyst layer.”
§ Full Parametric Study of the Influence of Ionomer Content, Catalyst Loading and Catalyst Type on Oxygen and Ion Transport in PEM Fuel Cell Catalyst Layers > 3. Results and Discussion > 3.1. Ex Situ Analysis
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“while the ionomer content has no effect on the overall thickness of the catalyst layer.”
§ Full Parametric Study of the Influence of Ionomer Content, Catalyst Loading and Catalyst Type on Oxygen and Ion Transport in PEM Fuel Cell Catalyst Layers > 3. Results and Discussion > 3.1. Ex Situ Analysis
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
38 more claims
Create a free account to see all 60 claims and every source verdict.
- Probably not a substantial claim. 2
- It may state two separate claims as one. 17
Citations
Cites
Handbook of fuel cells: fundamentals, technology, and applications
(2003) · Focus on Catalysts · doi:10.1016/s1351-4180(03)00850-x · Cited by 3,324
A sharp peak in the performance of sputtered platinum fuel cells at ultra-low platinum loading
O’Hayre, R., Lee, S.-J., Cha, S.-W., & Prinz, F. B. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00238-0 · Cited by 252
Sassin, M. B., Garsany, Y., Gould, B. D., & Swider-Lyons, K. E. (2017) · Analytical Chemistry · doi:10.1021/acs.analchem.6b03005 · Cited by 143 · cited 2×
“The effect of the manufacturing process on catalyst coated membranes produced in the lab was also investigated in [16].”
BackgroundMethodSaha, M. S., Gullá, A. F., Allen, R. J., & Mukerjee, S. (2006) · Electrochimica Acta · doi:10.1016/j.electacta.2006.01.006 · Cited by 142
Impact of manufacturing processes on proton exchange membrane fuel cell performance
Shahgaldi, S., Alaefour, I., & Li, X. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.05.086 · Cited by 138
Shahgaldi, S., Ozden, A., Li, X., & Hamdullahpur, F. (2018) · Energy Conversion and Management · doi:10.1016/j.enconman.2018.06.078 · Cited by 121
Yu, H., Roller, J. M., Mustain, W. E., & Marić, R. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.02.101 · Cited by 117
Garsany, Y., Atkinson, R. W., Sassin, M. B., Hjelm, R. M. E., Gould, B. D., & Swider-Lyons, K. E. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.1361805jes · Cited by 116
Gradient design of Pt/C ratio and Nafion content in cathode catalyst layer of PEMFCs
Chen, G., Wang, C., Lei, Y., Zhang, J., Mao, Z., Mao, Z., Guo, J., Li, J., & Ouyang, M. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.06.229 · Cited by 105
Understanding inks for porous-electrode formation
Hatzell, K. B., Dixit, M. B., Berlinger, S. A., & Weber, A. Z. (2017) · J. Mater. Chem. A · doi:10.1039/c7ta07255d · Cited by 97 · cited 1×
“In [7], a thorough review, focused on the analysis of the colloidal ink, was put forward, where the authors highlighted the importance of understanding the ink properties from a nanoscale in order to understand the macroscale effects.”
BackgroundAnalysis of Inkjet Printed PEFC Electrodes with Varying Platinum Loading
Shukla, S., Stanier, D., Saha, M. S., Stumper, J., & Secanell, M. (2016) · Journal of The Electrochemical Society · doi:10.1149/2.1111607jes · Cited by 95
Shahgaldi, S., Alaefour, I. E., & Li, X. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.02.154 · Cited by 94
Zamel, N. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.01.091 · Cited by 93
Self-citationSalari, S., Tam, M., McCague, C., Stumper, J., & Bahrami, M. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.227479 · Cited by 65
Xing, L., Shi, W., Das, P. K., & Scott, K. (2017) · AIChE Journal · doi:10.1002/aic.15826 · Cited by 61
A multi-layer structured cathode for the PEMFC
Yoon, Y., Yang, T., Park, G., Lee, W.-Y., & Kim, C.-S. (2003) · Journal of Power Sources · doi:10.1016/s0378-7753(03)00092-2 · Cited by 50
Chan, S., Janković, J., Susac, D., Saha, M. S., Tam, M., Yang, H., & Ko, F. (2018) · Journal of Power Sources · doi:10.1016/j.jpowsour.2018.02.001 · Cited by 47
Herden, S., Riewald, F., Hirschfeld, J. A., & Perchthaler, M. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.04.051 · Cited by 35
Ozden, A., Shahgaldi, S., Li, X., & Hamdullahpur, F. (2019) · Applied Energy · doi:10.1016/j.apenergy.2019.01.136 · Cited by 34
Alvar, E. N., Zhou, B., & Eichhorn, S. H. (2017) · International Journal of Energy Research · doi:10.1002/er.3746 · Cited by 23
Herden, S., Hirschfeld, J. A., Lohri, C., Perchthaler, M., & Haase, S. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.08.057 · Cited by 14
Cited by
Advances in Oxygen Evolution Electrocatalysts for Proton Exchange Membrane Water Electrolyzers
Chen, Z., Guo, L., Pan, L., Yan, T., He, Z., Li, Y., Shi, C., Huang, Z., Zhang, X., & Zou, J. (2022) · Advanced Energy Materials · doi:10.1002/aenm.202103670 · Cited by 298
Möller, T., Thanh, T. N., Wang, X., Ju, W., Jovanov, Z. P., & Strasser, P. (2021) · Energy & Environmental Science · doi:10.1039/d1ee01696b · Cited by 156
Xu, Y., Chang, G., Fan, R., & Cai, T. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2022.138924 · Cited by 104
Probing Ionomer Interactions with Electrocatalyst Particles in Solution
Berlinger, S. A., McCloskey, B. D., & Weber, A. Z. (2021) · ACS Energy Letters · doi:10.1021/acsenergylett.1c00866 · Cited by 93
Activation mechanisms in the catalyst coated membrane of PEM fuel cells
Christmann, K., Friedrich, K. A., & Zamel, N. (2021) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2021.100924 · Cited by 78
Self-citation
Metadata
- Authors
- Alink, R., Singh, R., Schneider, P., Christmann, K., Schall, J., Keding, R., & Zamel, N.
- Affiliations
- Fraunhofer Institute for Solar Energy Systems (DE)
- Corresponding author
- Zamel, Nada
- Venue
- Molecules
- Publisher
- MDPI AG
- Published
- 2020-03-27
- Volume
- 25
- Issue
- 7
- Pages
- 1523
- ISSN
- 1420-3049 (ISSN-L)
- PMC
- PMC7180721
- OpenAlex
- W3013228126
- Semantic Scholar
- 12af79bebabbfb8cc39abe8b7c5b6d15d5f3e404
- Cited by
- 77
- References
- 21
- Citations by year
- 2026: 14 · 2025: 18 · 2024: 12 · 2023: 14 · 2022: 11 · 2021: 8
- FWCI
- 2.83
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- Locations
- Molecules (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Publikationsdatenbank der Fraunhofer-Gesellschaft (Fraunhofer-Gesellschaft) (submittedVersion, other-oa)
- Fraunhofer-Publica (Fraunhofer-Gesellschaft) (submittedVersion, cc-by)
- Funders
- Bundesministerium für Bildung und Forschung (03SF0544A)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Keywords
- proton exchange membrane fuel cells, cathode catalyst layer, ionomer content, catalyst loading, platinum catalysts, oxygen transport, ion transport, membrane electrode assembly, high surface area carbon, parametric study
- MeSH terms
- Carbon, Catalysis, Electrochemistry, Electrodes, Electrolytes, Ions, Membranes, Artificial, Microscopy, Electron, Scanning, Oxygen, Platinum, Polymers
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.