The DOI matches its Crossref record; 70 of the 71 references it cites were found in a registry or an index; 17 of the 48 sources its claims cite were checked for support.
Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate
Open accessAbstract
Microwave-based reactions have gained traction in recent years due to their ability to enhance reaction rates and yield while reducing energy consumption. Also, according to the conception of 'waste to materials', various waste feeds are intensively sought to be tested. The experimental setup of this study involved varying pH levels, oxidation agents, and precipitation agents to optimize the synthesis process of iron red based on waste iron sulfate. The selection of oxidation and precipitation agents was found to significantly influence the pigment synthesis process. Various oxidizing agents, including hydrogen peroxide and atmospheric air, were evaluated for their effectiveness in promoting the oxidation of ferrous ions to ferric ions, essential for pigment formation. Additionally, different precipitation agents such as sodium hydroxide and ammonia solution were assessed for their ability to precipitate iron hydroxides and facilitate pigment particle formation. The characterization of synthesized pigments revealed promising results in terms of quality and color properties. Helium Ion Microscopy (HIM) analysis confirmed the formation of well-defined pigment particles with controlled morphology. X-ray diffraction (XRD) studies provided insights into the crystalline structure of the pigments, indicating the presence of characteristic iron oxide phases. By improving this technology, waste iron sulfate can be efficiently transformed into valuable iron pigments, offering a sustainable solution for waste management while meeting the growing demand for high-quality pigments.
Overview
CoChat Summary
TL;DR
The paper studies microwave-assisted synthesis of hematite pigments from waste iron sulfate while varying pH, oxidation agent, and precipitation agent. It reports that H₂O₂ gives better oxidation control, pH 10 gives the most homogeneous particle size distribution, pH 8 gives the best redness, and NaOH gives the largest BET surface area.
Key findings
- XRD showed mostly fine crystalline hematite; H₂O₂-oxidized pigments contained only well-crystalline hematite, while air-oxidized samples such as 8 air NH₃ contained magnetite (<20 wt%). Goethite was identified below 3 wt% in 10 H₂O₂ NaOH, 10 H₂O₂ NH₃, and 12 H₂O₂ NaOH; 12 air NaOH had about 7% Na₂SO₄ residual. NaOH-precipitated pigments had wide crystallite sizes of 30–350 nm, whereas ammonia-precipitated pigments had narrow sizes of 30–90 nm independent of pH and oxidant.
- BET specific surface areas were 4–52 m²/g, up to five times greater than commercial pigments (values up to 10 m²/g), with total pore volume <0.2 cm³/g; NaOH precipitation mostly gave higher surface areas. Oil absorption was 24–28 g/100 g, below the cited maximum value of 35 g/100 g.
- HIM showed irregular cube-like particles at pH 8, visible cubic small particles at pH 10, and irregular texture at pH 12; 12 H₂O₂ NaOH showed rhombic particles with many defects. DLS often showed narrow distributions of 0.1–1.5 µm but was not aligned with XRD and HIM results.
- Color analysis found pH 8 pigments had the best redness (highest a value); luminance was lower for ammonia-precipitated or air-oxidized pigments than for NaOH- or H₂O₂-treated pigments, while a and b did not change significantly with precipitation agent, oxidation agent, or pH. Magnetite presence darkened pigment color.
Methods
- Waste FeSO₄ was purified by recrystallization and used at 140 g/L. Oxidation used 10 g H₂O₂ for 10 min or air for 30 min; precipitation used 25 wt% ammonia water or 1M NaOH to pH 8, 10, or 12, with ammonia reaching a maximum pH of 11.56 so no ammonia pH 12 samples were included. Reactions ran in a microwave reactor for 1 h at about 160–165 °C and 17–20 bar; products were washed and dried at 105 °C for 4 h.
- Characterization included XRD with Co-Kα radiation and Rietveld refinement, FTIR, BET/DFT nitrogen adsorption, DLS, helium ion microscopy (HIM), oil absorption by PN-EN ISO 787-5:1999, and CIELAB color measurement with a Konica Minolta CM-700d.
Limitations
- Stated in the paper: ammonia could not reach pH 12, so no ammonia-precipitated pH 12 samples were studied; 12 air NaOH had about 7% Na₂SO₄ residual due to inaccurate washing; DLS results were not aligned with XRD and HIM results, e.g. 8 air NH₃ appeared homogeneous by DLS but contained two phases by XRD/HIM; FTIR could not distinguish hematite, goethite, or magnetite. The paper also notes potential agglomeration can be avoided by surface modifications.
- Evident from the text: the study uses one waste FeSO₄ source and one microwave reactor setup, so broader generalizability is not established.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures








![Figure 9 HIM image of reference material from previous research—14%, 20 bar, 3 h [50].](https://figures.cochat.ai/paper-figures/387fba14f3d845babf07544d00f58c1e/studies-of-the-morphology-of-hematite-synthesized-from-waste-iron-sulfate-figure-9.jpg)


Verification
Claims the paper makes
11 Valid · 4 Not valid · 6 Not checked · 64 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“Synthesized pigments have up to five times greater specific surface area than commercial pigments (values up to 10 m2/g) [65].”
§ Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate > 2. Results and Discussion > 2.3. BET
What the sources say
- Disputedcites [65] Splinter, K., Moszyński, D., and Lendzion-Bieluń, Z. (2023). Microwave-Reactor-Based Preparation of Red Iron Oxide Pigment from Waste Iron Sulfate. Materials, 16. sourceExperimental — accuracy not yet measured
In Results and Discussion §3.1.4, the paper says synthesized pigments have up to 20 times the specific surface area of commercial pigments, not five times. The Conclusions also report a surface area greater than 60 m²/g for the synthesized nanoparticles, contrary to the claimed value of up to 10 m²/g. (LLM, conf=0.90)
Checked by a reasoning model — may be wrong.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“However, the problem is the limited control of the size distribution of the obtained nanoparticles [17,19,20].”
§ Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate > 1. Introduction
What the sources say
- Not checked — no full text of the sourcecites [17] Supattarasakda, 2013, Control of hematite nanoparticle size and shape by the chemical precipitation method, Powder Technol. source
- Could not verifycites [19] Wang, 2022, Particle-based hematite crystallization is invariant to initial particle morphology, Proc. Natl. Acad. Sci. USA sourceExperimental — accuracy not yet measured
The Methods (Materials Synthesis; page unavailable) describe how the hematite nanoparticles were prepared, but do not assess control over their size distribution. Searches for “size distribution” and precipitation-related limitations found no passage in our copy supporting the attributed drawback. (LLM, conf=0.72)
- Not checked — no full text of the sourcecites [20] Li, 2022, Influences of starch depressant with the various molecular structure on the interactions between hematite particles and flotation bubbles, Colloids Surf. A Physicochem. Eng. Asp. source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
Every source the paper cites for this claim was checked and supports it.
In the paper
“However, according to the nomenclature proposed by IUPAC [63], several samples can be referred to as macroporous materials.”
§ Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate > 2. Results and Discussion > 2.3. BET
What the sources say
- Supportedcites [63] Rouquerol, 1994, Recommendations for the characterization of porous solids (Technical Report), Pure Appl. Chem. source
Section 5, “Idealized systems: pore shape and size,” gives the IUPAC classification: macropores have widths larger than 50 nm. The citation supports the nomenclature used to classify the citing authors’ samples. (LLM, conf=0.90)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Fe-O bond at these wavelengths, however, cannot distinguish between hematite (α-Fe2O3), goethite (α-FeOOH), or magnetite (Fe3O4) [3,51,52,53,54,55,56,57] (Figure 2).”
§ Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate > 2. Results and Discussion > 2.2. FTIR
What the sources say
- Partly supportedcites [3] Khanam, 2023, Development of ceramic grade red iron oxide pigment from waste iron source, Heliyon sourceExperimental — accuracy not yet measured
The Functional group analysis by FTIR section reports Fe–O absorption bands at 450–500 and 540–600 cm−1, encompassing 470 and 560 cm−1. It does not say those bands cannot distinguish hematite from goethite or magnetite; that is the unsupported part of the claim. (LLM, conf=0.85)
- Not checked — no full text of the sourcecites [51] Anju, 2017, Structural and multiferroic properties of barium substituted bismuth ferrite nanocrystallites prepared by sol–gel method, J. Magn. Magn. Mater. source
- Not checked — no full text of the sourcecites [52] Hwang, 2014, Synthesis and characterization of iron oxide nanoparticles for phenyl hydrazine sensor applications, Sens. Lett. source
- Not checked — no full text of the sourcecites [53] Chandel, 2017, Investigation of structural, optical, dielectric and magnetic studies of Mn substituted BiFeO3 multiferroics, Ceram. Int. source
- Not checked — no full text of the sourcecites [54] Weng, 2018, Removal of doxorubicin hydrochloride using Fe3O4 nanoparticles synthesized by euphorbia cochinchinensis extract, Chem. Eng. J. source
- Not checked — no full text of the sourcecites [55] Peng, 2012, 3D Network Magnetophotonic Crystals Fabricated on Morpho Butterfly Wing Templates, Adv. Funct. Mater. source
- Not checked — no full text of the sourcecites [56] Novoselova, 2020, Nanoscale magnetite: New synthesis approach, structure and properties, Appl. Surf. Sci. source
- Not checked — no full text of the sourcecites [57] Chen, 2022, Classification of archaeological adhesives from Eastern Europe and Urals by ATR-FT-IR spectroscopy and chemometric analysis, Archaeometry source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Obtained pigments have an isotherm shape corresponding to types IV and V according to the IUPAC classification [63,64] (Figure 3).”
§ Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate > 2. Results and Discussion > 2.3. BET
What the sources say
- Partly supportedcites [63] Rouquerol, 1994, Recommendations for the characterization of porous solids (Technical Report), Pure Appl. Chem. sourceExperimental — accuracy not yet measured
Section 4 discusses gas adsorption for characterizing pigments, and §4.3 uses a numbered isotherm category, Type I. Our copy does not describe Types IV and V, so it supports the general classification context but not those specific labels. The determination that the obtained pigments fit those types is the citing authors’ own interpretation of Figure 3. (LLM, conf=0.77)
- Supportedcites [64] Sing, 1985, Reporting physisorption data for gas/solid systems with special reference to the determination of surface area and porosity (Recommendations 1984), Pure Appl. Chem. source
Section 5.2 defines Type IV and Type V adsorption isotherms within the paper’s classification. The citation supports the classification used to describe the pigments’ isotherms; it is not offered as the source of the pigment measurements. (LLM, conf=0.90)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
51 more claims
Create a free account to see all 85 claims and every source verdict.
- Probably not a substantial claim. 20
- It may state two separate claims as one. 13
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate > 2. Results and Discussion > 2.1. XRD
“The content of only well-crystalline hematite characterizes pigments oxidized with hydrogen peroxide.”
§ Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate > 2. Results and Discussion > 2.1. XRD
“Goethite was identified in some samples, namely 10 H2O2 NaOH, 10 H2O2 NH3, and 12 H2O2 NaOH.”
Citations
Cites
CRC Handbook of Chemistry and Physics
(2014) · doi:10.1201/b17118 · Cited by 57,706
Sing, K. S. W. (1985) · Pure and Applied Chemistry · doi:10.1351/pac198557040603 · Cited by 24,485
Laurent, S., Forge, D., Port, M., Roch, A., Robic, C., Vander Elst, L., & Muller, R. N. (2008) · Chemical Reviews · doi:10.1021/cr068445e · Cited by 6,852 · cited 1×
“The average size of nanoparticles can be controlled by the pH and iron salt concentration [21].”
BackgroundRecommendations for the characterization of porous solids (Technical Report)
Rouquerol, J., Avnir, D., Fairbridge, C. W., Everett, D. H., Haynes, J. M., Pernicone, N., Ramsay, J. D. F., Sing, K. S. W., & Unger, K. K. (1994) · Pure and Applied Chemistry · doi:10.1351/pac199466081739 · Cited by 3,984
Profex: a graphical user interface for the Rietveld refinement program BGMN
Doebelin, N., & Kleeberg, R. (2015) · Journal of Applied Crystallography · doi:10.1107/s1600576715014685 · Cited by 1,808 · cited 1×
“Granted patent: Pat.245453 at 20.05.2024.”
InfluentialLegodi, M. A., & de Waal, D. (2007) · Dyes and Pigments · doi:10.1016/j.dyepig.2006.01.038 · Cited by 561
Organic Semiconductors based on Dyes and Color Pigments
Gsänger, M., Bialas, D., Huang, L., Stolte, M., & Würthner, F. (2016) · Advanced Materials · doi:10.1002/adma.201505440 · Cited by 467 · cited 1×
“This allows waste pigments to be used in a variety of industries where iron pigments are currently used, such as in paper coloring [7–9], electronics [10–12], paints [13,14], and cosmetics [15] (if they meet the requirements).”
BackgroundPreparation and magnetic properties of magnetite nanoparticles by sol–gel method
Xu, J., Yang, H., Fu, W., Du, K., Sui, Y., Chen, J., Zeng, Y., Li, M., & Zou, G. (2007) · Journal of Magnetism and Magnetic Materials · doi:10.1016/j.jmmm.2006.07.037 · Cited by 448
Magnetic Iron Oxide Nanoparticle (IONP) Synthesis to Applications: Present and Future
Ajinkya, N., Yu, X., Kaithal, P., Luo, H., Somani, P., & Ramakrishna, S. (2020) · Materials · doi:10.3390/ma13204644 · Cited by 362 · cited 1×
“However, cubic-shaped iron (III) oxide is obtained in high-temperature reactions (500 ◦ C) and in long synthesis times (5–20 h) [32,33].”
BackgroundHlawacek, G., Veligura, V., van Gastel, R., & Poelsema, B. (2014) · Journal of Vacuum Science & Technology B, Nanotechnology and Microelectronics: Materials, Processing, Measurement, and Phenomena · doi:10.1116/1.4863676 · Cited by 241 · cited 1×
“Granted patent: Pat.245453 at 20.05.2024.”
InfluentialSelf-citationBesenhard, M. O., LaGrow, A. P., Hodzic, A., Kriechbaum, M., Panariello, L., Bais, G., Loizou, K., Damilos, S., Margarida Cruz, M., Thanh, N. T. K., et al. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.125740 · Cited by 233 · cited 1×
“These alkalis play a crucial role in initiating the precipitation reaction by increasing the pH of the solution, which leads to the formation of insoluble iron hydroxide precipitates [22,23].”
BackgroundSynthesis and characterization of iron oxide nanoparticles for phenyl hydrazine sensor applications
Hwang, S. W., Umar, A., Dar, G. N., Kim, S. H., & Badran, R. I. (2014) · Sensor Letters · doi:10.1166/sl.2014.3224 · Cited by 216 · cited 1×
“Previous studies [50–52] have found that synthesized pigments based on waste iron sulfate differ significantly from commercially available pigments synthesized based on pure substances.”
BackgroundIn situ FTIR study on the dehydration of natural goethite
Prasad, P. S. R., Shiva Prasad, K., Krishna Chaitanya, V., Babu, E. V. S. S. K., Sreedhar, B., & Ramana Murthy, S. (2006) · Journal of Asian Earth Sciences · doi:10.1016/j.jseaes.2005.05.005 · Cited by 171 · cited 1×
“However, according DFT shows that some of the materials are actually mesoporous, so they have the largest proportion of pores in the 2–50 nm range (Figure 4). some samples show the highest proportion of pores In contrast, some samples show the highest proportion of pores above 50 nm, making them…”
BackgroundXue, Y., & Wang, Y. (2020) · Nanoscale · doi:10.1039/d0nr02705g · Cited by 128
Clean utilization of high-iron red mud by suspension magnetization roasting
Liu, X., Gao, P., Yuan, S., Lv, Y., & Han, Y. (2020) · Minerals Engineering · doi:10.1016/j.mineng.2020.106553 · Cited by 113
Li, S., Zhang, T., Tang, R., et al. (2014) · Journal of Magnetism and Magnetic Materials · doi:10.1016/j.jmmm.2014.12.054 · Cited by 112
Kozakova, Z., Kuřitka, I., Kazantseva, N. E., Babayan, V. A., Pastorek, M., Machovský, M., Bažant, P., & Sáha, P. (2015) · Dalton Transactions · doi:10.1039/c5dt03518j · Cited by 109 · cited 1×
“In this method, precursor solutions containing iron salts are sealed in a pressure vessel and heated under controlled conditions, promoting the nucleation and growth of hematite crystals [42–44].”
MethodZhan, S., Chen, D., Jiao, X., & Liu, S. (2007) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2006.12.026 · Cited by 108 · cited 1×
“Hematite obtained by precipitation in a neutral or low alkali pH ( 9) is characterized by a spherical particle shape and wide particle distribution, from 60 to 750 nm depending on research [28–30].”
BackgroundControl of hematite nanoparticle size and shape by the chemical precipitation method
Supattarasakda, K., Petcharoen, K., Permpool, T., Sirivat, A., & Lerdwijitjarud, W. (2013) · Powder Technology · doi:10.1016/j.powtec.2013.08.042 · Cited by 107 · cited 1×
“However, the problem is the limited control of the size distribution of the obtained nanoparticles [17,19,20].”
BackgroundWeng, X., Ma, L., Guo, M., Su, Y., Dharmarajan, R., & Chen, Z. (2018) · Chemical Engineering Journal · doi:10.1016/j.cej.2018.07.162 · Cited by 106
Highly sensitive NO2 gas sensor based on hematite nanoparticles synthesized by sol–gel technique
hjiri, M. (2020) · Journal of Materials Science Materials in Electronics · doi:10.1007/s10854-020-03069-4 · Cited by 103
3D Network Magnetophotonic Crystals Fabricated on Morpho Butterfly Wing Templates
Peng, W., Zhu, S., Wang, W., Zhang, W., Gu, J., Hu, X., Zhang, D., & Chen, Z. (2012) · Advanced Functional Materials · doi:10.1002/adfm.201103032 · Cited by 95
CIELAB color space boundaries under theoretical spectra and 99 test color samples
Durmus, D. (2020) · Color Research & Application · doi:10.1002/col.22521 · Cited by 89
Tahir, M., Fakhar-e-alam, M., Atif, M. M., Mustafa, G., & Ali, Z. (2023) · Journal of King Saud University - Science · doi:10.1016/j.jksus.2023.102695 · Cited by 82
Niu, Y., Yuan, Y., Zhang, Q., Chang, F., Yang, L., Chen, Z., & Bai, Z. (2020) · Nano Energy · doi:10.1016/j.nanoen.2020.105699 · Cited by 80
Potthast, A., Henniges, U., & Banik, G. (2008) · Cellulose · doi:10.1007/s10570-008-9237-1 · Cited by 78
Umar, A., Ibrahim, A. A., Kumar, R., et al. (2020) · Sensors and Actuators B Chemical · doi:10.1016/j.snb.2020.128851 · Cited by 76
Lassoued, A., Lassoued, M. S., Dkhil, B., et al. (2017) · Journal of Molecular Structure · doi:10.1016/j.molstruc.2017.03.077 · Cited by 74 · cited 1×
“The precipitation method involves adding an alkali to an aqueous salt solution containing iron ions [16–18].”
MethodThe precipitation of hematite from ferric chloride media
Riveros, P. A., & Dutrizac, J. E. (1997) · Hydrometallurgy · doi:10.1016/s0304-386x(97)00003-0 · Cited by 71 · cited 1×
“The precipitation method involves adding an alkali to an aqueous salt solution containing iron ions [16–18].”
MethodSynthesis of ceramic pigments from industrial wastes: Red mud and electroplating sludge
Carneiro, J., Tobaldi, D. M., Capela, M. N., Novais, R. M., Seabra, M. P. D. S., & Labrincha, J. A. (2018) · Waste Management · doi:10.1016/j.wasman.2018.09.032 · Cited by 70 · cited 1×
“This does not change the fact that new synthesis methods are constantly being developed to improve the properties of the materials obtained, minimize the negative impact on the environment, or use waste from other industries as raw materials for synthesis [1–6].”
Catalytic synthesis of nanosized hematite particles in solution
Liu, H., Wei, Y., Li, P., Zhang, Y., & Sun, Y. (2007) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2006.10.001 · Cited by 62 · cited 1×
“Hematite obtained by precipitation in a neutral or low alkali pH ( 9) is characterized by a spherical particle shape and wide particle distribution, from 60 to 750 nm depending on research [28–30].”
BackgroundLu, Y., Dong, W., Wang, W., Wang, Q., Hui, A., & Wang, A. (2018) · Applied Clay Science · doi:10.1016/j.clay.2018.10.008 · Cited by 62 · cited 1×
“This allows waste pigments to be used in a variety of industries where iron pigments are currently used, such as in paper coloring [7–9], electronics [10–12], paints [13,14], and cosmetics [15] (if they meet the requirements).”
BackgroundChandel, S., Thakur, P., Tomar, M., Gupta, V., & Thakur, A. (2017) · Ceramics International · doi:10.1016/j.ceramint.2017.07.088 · Cited by 60
Nanoscale magnetite: New synthesis approach, structure and properties
Novoselova, L. Y. (2021) · Applied Surface Science · doi:10.1016/j.apsusc.2020.148275 · Cited by 54
Ni, X. F., Zhang, J., Zhao, L., Wang, F., He, H., & Dramou, P. (2022) · Journal of Physics and Chemistry of Solids · doi:10.1016/j.jpcs.2022.110855 · Cited by 52 · cited 1×
“However, this type of process is often results in a very long synthesis time (>10 h) [47–49].”
BackgroundPaulson, E., & Jothibas, M. (2021) · Surfaces and Interfaces · doi:10.1016/j.surfin.2021.101432 · Cited by 49 · cited 1×
“This technique relies on the hydrolysis and condensation of metal alkoxides or salts to form a sol, which subsequently undergoes gelation and calcination to yield hematite nanoparticles [36,37].”
MethodComparison of Different Enhanced Coagulation Methods for Azo Dye Removal from Wastewater
Luo, X., Chen, L., & Hu, Y. (2019) · Sustainability · doi:10.3390/su11174760 · Cited by 48
Borges, R., Mendonça-Ferreira, L., Rettori, C., et al. (2020) · Materials Science and Engineering C · doi:10.1016/j.msec.2020.111692 · Cited by 47
Continuous production of magnetic iron oxide nanocrystals by oxidative precipitation
Asimakidou, T., Makridis, A., Veintemillas-Verdaguer, S., Morales, M. P., Kellartzis, I., Mitrakas, M. G., Vourlias, G., Angelakeris, M., & Simeonidis, K. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.124593 · Cited by 46 · cited 1×
“These alkalis play a crucial role in initiating the precipitation reaction by increasing the pH of the solution, which leads to the formation of insoluble iron hydroxide precipitates [22,23].”
BackgroundNot only wall paintings—pigments for cosmetics
Pérez‐Arantegui, J. (2021) · Archaeological and Anthropological Sciences · doi:10.1007/s12520-021-01399-w · Cited by 42 · cited 1×
“This allows waste pigments to be used in a variety of industries where iron pigments are currently used, such as in paper coloring [7–9], electronics [10–12], paints [13,14], and cosmetics [15] (if they meet the requirements).”
BackgroundKhorshidi, N., & Azadmehr, A. R. (2017) · Desalination and Water Treatment · doi:10.5004/dwt.2017.0038 · Cited by 39 · cited 1×
“However, according to the nomenclature proposed by IUPAC [63], several samples can be referred to as macroporous materials.”
BackgroundAnju, Agarwal, A., Aghamkar, P., & Lal, B. (2017) · Journal of Magnetism and Magnetic Materials · doi:10.1016/j.jmmm.2016.09.103 · Cited by 36 · cited 1×
“This broad It is a typical characteristic of mesoporous materials.”
BackgroundSynthesis of iron red hybrid pigments from oil shale semi-coke waste
Lu, Y., Xu, J., Wang, W., Wang, T., Zong, L., & Wang, A. (2020) · Advanced Powder Technology · doi:10.1016/j.apt.2020.03.020 · Cited by 36 · cited 1×
“In addition, pigments synthesized based on waste raw materials have comparable or better physical and chemical properties [4].”
BackgroundChen, S., Vahur, S., Teearu, A., Juus, T., Zhilin, M., Savchenko, S., Oshibkina, S., Asheichyk, V., Vashanau, A., Lychagina, E., et al. (2022) · Archaeometry · doi:10.1111/arcm.12686 · Cited by 33 · cited 2×
“…of the materials are actually mesoporous, so they have the largest proportion of pores in the 2–50 nm range (Figure 4). some samples show the highest proportion of pores In contrast, some samples show the highest proportion of pores above 50 nm, making them macroporous. above 50 nm, making them…”
BackgroundParticle-based hematite crystallization is invariant to initial particle morphology
Wang, Y., Xue, S., Lin, Q., Song, D., He, Y., Liu, L., Zhou, J., Zong, M., De Yoreo, J. J., Zhu, J., et al. (2022) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.2112679119 · Cited by 29 · cited 1×
“However, the problem is the limited control of the size distribution of the obtained nanoparticles [17,19,20].”
BackgroundControllable fabrication and growth mechanism of hematite cubes
Su, C., Wang, H., & Liu, X. (2011) · Crystal Research and Technology · doi:10.1002/crat.201000642 · Cited by 28 · cited 1×
“It is shown that when using a pH higher than 9, hematite can create cubic shape particles [31].”
BackgroundQuantitative GC–MS Analysis of Artificially Aged Paints with Variable Pigment and Linseed Oil Ratios
Tammekivi, E., Vahur, S., Vilbaste, M., & Leito, I. (2021) · Molecules · doi:10.3390/molecules26082218 · Cited by 26 · cited 1×
“…the materials are actually mesoporous, so they have the largest proportion of pores in the 2–50 nm range (Figure 4). some samples show the highest proportion of pores In contrast, some samples show the highest proportion of pores above 50 nm, making them macroporous. above 50 nm, making them…”
BackgroundLi, K., Zhang, H., Peng, T., Liu, C., & Yang, S. (2022) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2022.129814 · Cited by 26 · cited 1×
“However, the problem is the limited control of the size distribution of the obtained nanoparticles [17,19,20].”
BackgroundColorful liquid metal printed electronics
Liang, S., & Liu, J. (2017) · Science China Technological Sciences · doi:10.1007/s11431-017-9116-9 · Cited by 25
Wu, X., Lee, B., & Jun, Y. (2020) · Environmental Science & Technology · doi:10.1021/acs.est.0c03160 · Cited by 24
Ullrich, A., Rahman, M. M., Azhar, A., Kühn, M., & Albrecht, M. (2022) · Journal of Nanoparticle Research · doi:10.1007/s11051-022-05554-9 · Cited by 24 · cited 1×
“Additionally, other complexing agents or chelating agents such as ethylenediaminetetraacetic acid (EDTA) may be used in conjunction with alkalis to enhance the stability of the precursor solution and promote homogeneous nucleation [24–27].”
BackgroundDevelopment of ceramic grade red iron oxide pigment from waste iron source
Khanam, J., Hasan, M. R., Biswas, B., Jahan, S. A., Sharmin, N., Ahmed, S., & Al-Reza, S. M. (2023) · Heliyon · doi:10.1016/j.heliyon.2023.e12854 · Cited by 21
Chong, E., Marak, K. E., Li, Y., & Freedman, M. A. (2021) · Physical Chemistry Chemical Physics · doi:10.1039/d0cp04220j · Cited by 19
Mallesh, S., Narsimulu, D., & Kim, K. H. (2019) · Physics Letters A · doi:10.1016/j.physleta.2019.126038 · Cited by 16 · cited 1×
“The hydrothermal method offers distinct advantages, including the ability to synthesize single-crystalline nanoparticles with precise control over size, shape, and crystal orientation [45,46].”
BackgroundLukić, M. J., Gebauer, D., & Rose, A. L. (2020) · Current Opinion in Colloid & Interface Science · doi:10.1016/j.cocis.2020.03.010 · Cited by 16 · cited 1×
“Additionally, other complexing agents or chelating agents such as ethylenediaminetetraacetic acid (EDTA) may be used in conjunction with alkalis to enhance the stability of the precursor solution and promote homogeneous nucleation [24–27].”
BackgroundGong, L., Hua, X., Yao, B., Liang, J., & Tian, G. (2022) · Ceramics International · doi:10.1016/j.ceramint.2022.10.021 · Cited by 16
Rehman, S., Ahmed, F., Khan, M. U. A., et al. (2022) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2022.108909 · Cited by 15 · cited 1×
“In this method, precursor solutions containing iron salts are sealed in a pressure vessel and heated under controlled conditions, promoting the nucleation and growth of hematite crystals [42–44].”
MethodFTIR transmission spectroscopy of sideronatrite, a sodium-iron hydrous sulfate
Della Ventura, G., Ventruti, G., Bellatreccia, F., Scordari, F., & Cestelli Guidi, M. (2013) · Mineralogical Magazine · doi:10.1180/minmag.2013.077.4.09 · Cited by 12 · cited 1×
“It should be noted, however, that the analyzed materials have a It should be noted, however, that the analyzed materials have a small total pore volume of <0.2 cm 3 /g. small total pore volume of <0.2 cm 3 /g.”
BackgroundInfluentialPreparation of the carbon sphere coated with iron oxide and its application for electronic paper
Lee, K. U., Park, K. J., Kim, M. H., Kwon, O. J., & Kim, J. J. (2013) · Dyes and Pigments · doi:10.1016/j.dyepig.2013.10.012 · Cited by 9 · cited 1×
“This allows waste pigments to be used in a variety of industries where iron pigments are currently used, such as in paper coloring [7–9], electronics [10–12], paints [13,14], and cosmetics [15] (if they meet the requirements).”
BackgroundGölzhäuser, A., & Hlawacek, G. (2016) · Nanoscience and technology · doi:10.1007/978-3-319-41990-9_7 · Cited by 8 · cited 1×
“Granted patent: Pat.245453 at 20.05.2024.”
InfluentialSelf-citationMicrowave-Reactor-Based Preparation of Red Iron Oxide Pigment from Waste Iron Sulfate
Splinter, K., Moszyński, D., & Lendzion-Bieluń, Z. (2023) · Materials · doi:10.3390/ma16083242 · Cited by 8 · cited 5×
“Many samples are characterized by a narrow size distribution of particles in a range of 0.1–1.5 µm.”
BackgroundMethodInfluentialSelf-citationUtari, Maulidina, H., Arilasita, R., et al. (2023) · Materials Research Express · doi:10.1088/2053-1591/acbf0c · Cited by 6 · cited 1×
“This technique relies on the hydrolysis and condensation of metal alkoxides or salts to form a sol, which subsequently undergoes gelation and calcination to yield hematite nanoparticles [36,37].”
MethodPreparation of Iron Oxide Pigments for Mineral Paints from Solid Iron-Containing Waste
Епихин, А. Н., & Krylova, A. V. (2003) · Russian Journal of Applied Chemistry · doi:10.1023/a:1023371228302 · Cited by 5
Introduction to Imaging Techniques in the HIM
Boden, S. A. (2016) · Nanoscience and technology · doi:10.1007/978-3-319-41990-9_6 · Cited by 5 · cited 1×
“Granted patent: Pat.245453 at 20.05.2024.”
InfluentialSimple solvothermal approach to highly nanostructured hematite thin films
Platnich, C. M., Slaby, J., O’Connell, D., & Trudel, S. (2020) · Canadian Journal of Chemistry · doi:10.1139/cjc-2020-0334 · Cited by 5
Synthesis and characterization of iron Oxide (hematite) nanoparticles by sol-gel method
Jegadeeswari, A., & Punitha, T. (2020) · Nanoscale Reports · doi:10.26524/nr.3.23 · Cited by 3 · cited 1×
“The sol–gel method’s versatility and ability to produce nanoparticles with a high surface area make it particularly attractive for applications such as photocatalysis and magnetic storage [38–41].”
MethodÇanakçı, D. (2021) · Hacettepe Journal of Biology and Chemistry · doi:10.15671/hjbc.691065 · Cited by 3 · cited 1×
“In contrast, the sol–gel method offers a more tailored approach to hematite synthesis [34,35].”
MethodThe Effect of Iron Ions from Prussian Blue Pigment on the Deterioration of Japanese Paper
Kida, K., Potthast, A., Inaba, M., et al. (2015) · Restaurator International Journal for the Preservation of Library and Archival Material · doi:10.1515/res-2015-0009 · Cited by 2 · cited 1×
“This allows waste pigments to be used in a variety of industries where iron pigments are currently used, such as in paper coloring [7–9], electronics [10–12], paints [13,14], and cosmetics [15] (if they meet the requirements).”
BackgroundHan, Y., Shan, M., Lu, Y., et al. (2022) · Materials Research Express · doi:10.1088/2053-1591/ac7384 · Cited by 2 · cited 1×
“This allows waste pigments to be used in a variety of industries where iron pigments are currently used, such as in paper coloring [7–9], electronics [10–12], paints [13,14], and cosmetics [15] (if they meet the requirements).”
BackgroundSplinter, K., & Lendzion-Bieluńb, Z. (2023) · Chemical and Process Engineering: New Frontiers · doi:10.24425/cpe.2023.144698 · Cited by 1 · cited 6×
“However, the DLS results are not aligned with the XRD and HIM results.”
BackgroundMethodResultInfluentialSelf-citation
Cited by
Magnetic Hematite (α-Fe2O3) Photocatalyst in Wastewater Treatment
Moattari, R. M., & Mahinroosta, M. (2025) · Smart nanomaterials technology · doi:10.1007/978-981-96-7683-5_8 · Cited by 2
Sol-gel auto-combustion synthesis and characterization of potassium ferrite
de Azevedo, A. M., da Silveira, P. H. P. M., Lima, R. D. M. C., Sánchez, D. R., Gomes, A. M., Lima, A. M., Monteiro, S. N., Cardoso, D. D., de Biasi, R. S., Silveira, P. C. R., et al. (2025) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2025.12.178 · Cited by 2
Srour, A., Harajli, Z., Saadeh, L., Yassin, A., Isber, S., Haidar, M., & Malaeb, W. (2026) · Ceramics International · doi:10.1016/j.ceramint.2026.02.345 · Cited by 1
Di, Y., Yue, X., Li, F., et al. (2025) · SSRN Electronic Journal · doi:10.2139/ssrn.5636538
Nano-Oxide Milling of Waste-Derived Hematite Pigments for Enhanced Functional PropertiesPreprint
Splinter, K., Moeckel, R., Patil, A. B., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6320084
Self-citation
Metadata
- Authors
- Splinter, K., Möckel, R., Hlawacek, G., & Lendzion-Bieluń, Z.
- Affiliations
- West Pomeranian University of Technology in Szczecin (PL)
- Helmholtz-Zentrum Dresden-Rossendorf (DE)
- Department of Inorganic Chemical Technology and Environment Engineering, Faculty of Chemical Technology and Engineering, West Pomeranian University of Technology in Szczecin, Piastów Ave. 42, 71-065 Szczecin, Poland
- Venue
- Molecules
- Publisher
- MDPI AG
- Published
- 2024-07-26
- Volume
- 29
- Issue
- 15
- Pages
- 3527
- ISSN
- 1420-3049 (ISSN-L)
- PMC
- PMC11314163
- OpenAlex
- W4401015602
- Semantic Scholar
- 3c36da326c0ec231cbbebec953851a719c6697c6
- Cited by
- 7
- References
- 71
- Citations by year
- 2026: 4 · 2025: 3
- FWCI
- 0.77
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Molecules (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Chemistry › Inorganic Chemistry › Pigment Synthesis and Properties
- Physical Sciences › Materials Science › Materials Chemistry › Iron oxide chemistry and applications
- Physical Sciences › Engineering › Building and Construction › Recycling and utilization of industrial and municipal waste in materials production
- Keywords
- hematite, microwave-assisted synthesis, hydrogen peroxide oxidation, precipitating agents, sodium hydroxide, ammonia, pH optimization, pigment morphology, iron hydroxide precipitation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.