Latent Heat Storage and Thermal Efficacy of Carboxymethyl Cellulose Carbon Foams Containing Ag, Al, Carbon Nanotubes, and Graphene in a Phase Change Material
Open accessThe DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
Abstract
Carbon foam was prepared from carboxymethyl cellulose (CMC) and Ag, Al and carbon nanotubes (CNTs), and graphene was added to the foam individually, to investigate the enhancement effects on the thermal conductivity. In addition, we used the vacuum method to impregnate erythritol of the phase change material (PCM) into the carbon foam samples to maximize the latent heat and minimize the latent heat loss during thermal cycling. Carbon foams containing Ag (CF-Ag), Al (CF-Al), CNT (CF-CNT) and graphene (CF-G) showed higher thermal conductivity than the carbon foam without any nano thermal conducting materials (CF). From the variations in temperature with time, erythritol added to CF, CF-Ag, CF-Al, CF-CNT, and CF-G was observed to decrease the time required to reach the phase change temperature when compared with pure erythritol. Among them, erythritol added to CF-G had the fastest phase change temperature, and this was related to the fact that this material had the highest thermal conductivity of the carbon foams used in this study. According to differential scanning calorimetry (DSC) analyses, the materials in which erythritol was added (CF, CF-Ag, CF-Al, CF-CNT, and CF-G) showed lower latent heat values than pure erythritol, as a result of their supplementation with carbon foam. However, the latent heat loss of these supplemented materials was less than that of pure erythritol during thermal cycling tests because of capillary and surface tension forces.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures






Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source doesn’t support the claim as written.
In the citing paper
“Enhancement in thermal conductivity ranged from 150 to 225%, with Ag, Al, CNT, and graphene increasing in that order.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [91]
Checked by a reasoning model — may be wrong.
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Latent heat was reduced with the addition of foam but stayed relatively the same with the addition of the NPs; however, latent heat loss during thermal cycling was lower with the foam [91].”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [91]
The cited source says what the claim attributes to it.
In the citing paper
“All NP-foam combinations enhanced thermal conductivity when compared to carbon foam without NPs.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [91]
The cited source says what the claim attributes to it.
In the citing paper
“Melting time also decreased, in the same order with graphene as the fastest melting time.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [91]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Review on thermal energy storage with phase change materials and applications
Sharma, A., Tyagi, V. V., Chen, C. R., & Buddhi, D. (2009) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2007.10.005 · Cited by 5,936
Zalba, B., Marı́n, J. M., Cabeza, L. F., & Mehling, H. (2003) · Applied Thermal Engineering · doi:10.1016/s1359-4311(02)00192-8 · Cited by 4,738
Carbon materials for electrochemical capacitors
Inagaki, M., Konno, H., & Tanaike, O. (2010) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.06.036 · Cited by 1,404 · cited 1×
“Carbon foam has three-dimensional (3D) netlike construction and has been widely used in applications, such as electrode materials [23], heavy oil recovery [24], and sound energy absorption [25,26].”
MethodA review on carbon nanotubes and graphene as fillers in reinforced polymer nanocomposites
Mittal, G., Dhand, V., Rhee, K. Y., Park, S.-J., & Lee, W. R. (2015) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2014.03.022 · Cited by 1,371 · cited 1×
“Thermal annealing at high temperature near 1000 ◦C has been proposed as the classic temperature for GO reduction resulting in rGO [33,34].”
BackgroundPCM thermal storage in buildings: A state of art
Tyagi, V. V., & Buddhi, D. (2007) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2005.10.002 · Cited by 1,090
IEA EBC Annex 67 Energy Flexible Buildings
Jensen, S. Ø., Marszal-Pomianowska, A., Lollini, R., Pasut, W., Knotzer, A., Engelmann, P., Stafford, A., & Reynders, G. (2017) · Energy and Buildings · doi:10.1016/j.enbuild.2017.08.044 · Cited by 490
Finck, C., Li, R., Kramer, R., & Zeiler, W. (2018) · Applied Energy · doi:10.1016/j.apenergy.2017.11.036 · Cited by 239 · cited 1×
“Thermal energy generated from fossil fuels is a type of high-quality energy that can be easily converted into mechanical energy and electric energy [1,2].”
BackgroundKarthik, M., Faik, A., Blanco-Rodríguez, P., Rodríguez-Aseguinolaza, J., & D’Aguanno, B. (2015) · Carbon · doi:10.1016/j.carbon.2015.06.075 · Cited by 186 · cited 1×
“[21] prepared erythritol-graphite foam as a stable composite PCM and used the wetness impregnation method for the utilization and recovery of solar heat or industrial waste heat.”
MethodSynthesis and characterization of seaweed cellulose derived carboxymethyl cellulose
Lakshmi, D. S., Trivedi, N., & Reddy, C. R. K. (2017) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.11.042 · Cited by 182
Al-Jethelah, M., Ebadi, S., Venkateshwar, K., Tasnim, S. H., Mahmud, S., & Dutta, A. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.11.121 · Cited by 181
Li, Y., Li, J., Deng, Y., Guan, W., Wang, X., & Qian, T. (2016) · Applied Energy · doi:10.1016/j.apenergy.2016.03.010 · Cited by 176
Thermal analysis of phase change materials in the temperature range 120–150°C
Haillot, D., Bauer, T., Kröner, U., & Tamme, R. (2010) · Thermochimica Acta · doi:10.1016/j.tca.2010.11.011 · Cited by 152 · cited 1×
“Thermal energy generated from fossil fuels is a type of high-quality energy that can be easily converted into mechanical energy and electric energy [1,2].”
BackgroundDidaskalou, C., Büyüktıryakı, S., Keçili, R., Fonte, C. P., & Székely, G. (2017) · Green Chemistry · doi:10.1039/c7gc00912g · Cited by 144 · cited 1×
“While CMC is an attractive material from eco-friendly and economic perspectives [29–31] to reduce the negative environmental effects [32], the thermal conductivity of CMC carbon foam is not very satisfactory.”
BackgroundNomura, T., Okinaka, N., & Akiyama, T. (2010) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2010.02.007 · Cited by 140
Melting behaviors of PCM in porous metal foam characterized by fractal geometry
Deng, Z., Liu, X., Zhang, C., Huang, Y., & Chen, Y. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.05.126 · Cited by 135
Shin, H. K., Park, M., Kim, H. Y., & Park, S. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2014.10.035 · Cited by 131 · cited 1×
“[20] selected expanded graphites (EGs), which are one type of porous carbon material, as fillers and then researched the effects of the EGs on the thermal conductivity following impregnation of sodium acetate trihydrate (SAT) as the PCM.”
MethodSelf-citationMesophase pitch based carbon foams as sound absorbers
Gao, N., Cheng, B., Hou, H., & Zhang, R. (2017) · Materials Letters · doi:10.1016/j.matlet.2017.10.074 · Cited by 129 · cited 1×
“Carbon foam has three-dimensional (3D) netlike construction and has been widely used in applications, such as electrode materials [23], heavy oil recovery [24], and sound energy absorption [25,26].”
MethodLee, S., Shin, H. K., Park, M., Rhee, K. Y., & Park, S. (2013) · Carbon · doi:10.1016/j.carbon.2013.09.053 · Cited by 123
Self-citationPEG 400-Based Phase Change Materials Nano-Enhanced with Functionalized Graphene Nanoplatelets
Marcos, M., Cabaleiro, D., Guimarey, M., Comuñas, M., Fedele, L., Fernández, J., & Lugo, L. (2017) · Nanomaterials · doi:10.3390/nano8010016 · Cited by 121
Agrawal, P. R., Kumar, R., Teotia, S., Kumari, S., Mondal, D. P., & Dhakate, S. R. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.10.033 · Cited by 113 · cited 1×
“Thermal annealing at high temperature near 1000 ◦C has been proposed as the classic temperature for GO reduction resulting in rGO [33,34].”
BackgroundCarbon foams produced from lignin-phenol-formaldehyde resin for oil/water separation
Qu, J., Han, Q., Gao, F., & Qiu, J. (2017) · New Carbon Materials · doi:10.1016/s1872-5805(17)60109-4 · Cited by 83
Graphene foam/carbon nanotube/poly(dimethyl siloxane) composites as excellent sound absorber
Wu, Y., Sun, X., Wu, W., Liu, X., Lin, X., Shen, X., Wang, Z., Li, R. K. Y., Yang, Z., Lau, K.-T., et al. (2017) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2017.09.001 · Cited by 81 · cited 1×
“Carbon foam has three-dimensional (3D) netlike construction and has been widely used in applications, such as electrode materials [23], heavy oil recovery [24], and sound energy absorption [25,26].”
MethodJana, P., Fierro, V., Pizzi, A., & Celzard, A. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.06.057 · Cited by 72 · cited 2×
“Generally, the thermal conductivity of non-graphitized carbon foam will have a low value below 1 W mK-1 [35], and here, the thermal conductivity of CF without nano thermal conducting materials was 0.”
BackgroundKaizawa, A., Kamano, H., Kawai, A., Jozuka, T., Senda, T., Maruoka, N., Okinaka, N., & Akiyama, T. (2008) · ISIJ International · doi:10.2355/isijinternational.48.540 · Cited by 72
Benslimane, A., Bahlouli, I., Bekkour, K., & Hammiche, D. (2016) · Applied Clay Science · doi:10.1016/j.clay.2016.08.026 · Cited by 65
Shin, H. K., Rhee, K. Y., & Park, S. (2016) · Composites Part B Engineering · doi:10.1016/j.compositesb.2016.04.033 · Cited by 64
Self-citationWang, X., Guo, Y.-D., Su, J., Zhang, X., Han, N., & Wang, X. (2018) · Nanomaterials · doi:10.3390/nano8060364 · Cited by 42
Solar energy latent thermal storage by phase change materials (PCMs) in a honeycomb system
Andreozzi, A., Buonomo, B., Ercole, D., & Manca, O. (2018) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2018.02.003 · Cited by 41
Xiao, H., Tao, C.-A., Li, Y., Chen, X., Huang, J., & Wang, J. (2018) · Nanomaterials · doi:10.3390/nano8100854 · Cited by 22 · cited 8×
“Therefore, it can be concluded that CF, CF-Ag, CF-Al, CF-CNT, and CF-G demonstrated great thermal reliability as fillers for PCMs. Nanomaterials 2018, 8, x FOR PEER REVIEW 7 of 11 ~5% of the initial latent heat value was lost.”
BackgroundInfluentialKim, H. G., Kwac, L. K., Kim, Y.-S., Shin, H. K., & Rhee, K. Y. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.06.013 · Cited by 16 · cited 2×
“Here, carbon foam was prepared from carboxymethyl cellulose (CMC) derived from cellulose [27,28].”
MethodSelf-citationHollow structured porous carbon fibers with the inherent texture of the cotton fibers
Sagisaka, K., Kondô, A., Iiyama, T., Kimura, M., Fujimoto, H., Touhara, H., & Hattori, Y. (2018) · Chemical Physics Letters · doi:10.1016/j.cplett.2018.08.081 · Cited by 16 · cited 8×
“Therefore, it can be concluded that CF, CF-Ag, CF-Al, CF-CNT, and CF-G demonstrated great thermal reliability as fillers for PCMs. Nanomaterials 2018, 8, x FOR PEER REVIEW 7 of 11 ~5% of the initial latent heat value was lost.”
BackgroundInfluentialWu, Z., Sheng, W., Tao, W., & Li, Z. (2018) · Solar Energy · doi:10.1016/j.solener.2018.05.014 · Cited by 13
Kim, H., Kim, Y., Kwac, L. K., Chae, S., & Shin, H. J. (2018) · Materials · doi:10.3390/ma11040469 · Cited by 10 · cited 2×
“Here, carbon foam was prepared from carboxymethyl cellulose (CMC) derived from cellulose [27,28].”
MethodSelf-citationRole of electron beam irradiation on superabsorbent behaviors of carboxymethyl cellulose
Shin, H. K., Park, M., Kang, P. H., Rhee, K. Y., & Park, S. (2014) · Research on Chemical Intermediates · doi:10.1007/s11164-014-1779-2 · Cited by 9
Self-citationLi, J., Lu, W., Luo, Z., & Zeng, Y. (2017) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/182/1/012009 · Cited by 5 · cited 1×
“[22] researched the thermal performance enhancement of erythritol/carbon foam composites.”
Background
Cited by
Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review
Tofani, K., & Tiari, S. (2021) · Energies · doi:10.3390/en14133821 · Cited by 114
“Latent heat was reduced with the addition of foam but stayed relatively the same with the addition of the NPs; however, latent heat loss during thermal cycling was lower with the foam [91].”
BackgroundMethodInfluentialZhu, X., Wang, Q., Kang, S., Li, J., & Jia, X. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.125112 · Cited by 95
Yuan, M., Xu, C., Wang, T., Zhang, T., Pan, X., & Ye, F. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.127394 · Cited by 90
Biobased foams for thermal insulation: material selection, processing, modelling, and performance
Mort, R., Vorst, K., Curtzwiler, G. W., & Jiang, S. (2021) · RSC Advances · doi:10.1039/d0ra09287h · Cited by 84
A review of phase change materials and heat enhancement methodologies
Saqib, M., & Andrzejczyk, R. (2022) · Wiley Interdisciplinary Reviews Energy and Environment · doi:10.1002/wene.467 · Cited by 54
Metadata
- Authors
- Kim, H. G., Kim, Y.-S., Kwac, L. K., Shin, H. J., Lee, S. O., Lee, U. S., & Shin, H. K.
- Affiliations
- Jeonju University (KR)
- Institute of Carbon Technology, Jeonju University, 303 Cheonjam-ro, Wansan-gu, Jeonju-si, Jeollabuk-do 55069, Korea
- Corresponding author
- Shin, Hye Kyoung
- Venue
- Nanomaterials
- Publisher
- MDPI AG
- Published
- 2019-01-28
- Volume
- 9
- Issue
- 2
- Pages
- 158
- ISSN
- 2079-4991 (ISSN-L)
- PMC
- PMC6410109
- OpenAlex
- W2911907592
- Cited by
- 22
- References
- 35
- Citations by year
- 2026: 3 · 2025: 1 · 2024: 3 · 2023: 3 · 2022: 2 · 2021: 5 · 2020: 5
- FWCI
- 1.69
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- Locations
- Nanomaterials (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion, other-oa)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- National Research Foundation (2016R1A6A1A03012069)
- Ministry of Science, ICT and Future Planning (2017R1A2B1008753)
- National Research Foundation of Korea (2016R1A6A1A03012069, No. 2016R1A6A1A03012069)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Phase Change Materials Research
- Physical Sciences › Materials Science › Materials Chemistry › Thermal properties of materials
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Keywords
- latent heat storage, phase change materials, erythritol, thermal conductivity enhancement, silver nanoparticles, aluminum nanoparticles, carbon nanotubes, graphene, vacuum impregnation, latent heat loss, thermal cycling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.