The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Multi-Material Additive Manufacturing of Sustainable Innovative Materials and Structures
Open accessAbstract
This paper highlights the multi-material additive manufacturing (AM) route for manufacturing of innovative materials and structures. Three different recycled thermoplastics, namely acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), and high impact polystyrene (HIPS) (with different Young’s modulus, glass transition temperature, rheological properties), have been selected (as a case study) for multi-material AM. The functional prototypes have been printed on fused deposition modelling (FDM) setup as tensile specimens (as per ASTM D638 type-IV standard) with different combinations of top, middle, and bottom layers (of ABS/PLA/HIPS), at different printing speed and infill percentage density. The specimens were subjected to thermal (glass transition temperature and heat capacity) and mechanical testing (peak load, peak strength, peak elongation, percentage elongation at peak, and Young’s modulus) to ascertain their suitability in load-bearing structures, and the fabrication of functional prototypes of mechanical meta-materials. The results have been supported by photomicrographs to observe the microstructure of the analyzed multi-materials.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Momeni, F., M.Mehdi Hassani.N, S., Liu, X., & Ni, J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.02.068 · Cited by 1,165
Cited by
Additive Manufacturing of Polymer Materials: Progress, Promise and Challenges
Saleh Alghamdi, S., John, S., Roy Choudhury, N., & Dutta, N. K. (2021) · Polymers · doi:10.3390/polym13050753 · Cited by 469
Review on Additive Manufacturing of Multi-Material Parts: Progress and Challenges
Hasanov, S., Alkunte, S., Rajeshirke, M., Gupta, A., Huseynov, O., Fidan, I., Alifui-Segbaya, F., & Rennie, A. (2021) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp6010004 · Cited by 258
Al Rashid, A., Khan, S. A., G. Al-Ghamdi, S., & Koç, M. (2020) · Automation in Construction · doi:10.1016/j.autcon.2020.103268 · Cited by 257
2D/3D Direct Writing of Thermoplastics through Electrohydrodynamic Printing
Paralı, L., Koç, M., & Yıldız, Z. (2022) · Polymer Science, Series A · doi:10.1134/s0965545x22700183 · Cited by 2
Metadata
- Authors
- Singh, R., Kumar, R., Farina, I., Colangelo, F., Feo, L., & Fraternali, F.
- Venue
- Polymers
- Publisher
- MDPI AG
- Published
- 2019-01-04
- Volume
- 11
- Issue
- 1
- Pages
- 62
- ISSN
- 2073-4360 (ISSN-L)
- OpenAlex
- W2908055620
- Cited by
- 194
- References
- 2
- FWCI
- 11.56
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Multi-Material Additive Manufacturing of Sustainable Innovative Materials and Structures. https://app.cochat.ai/papers/10.3390/polym11010062
- The paper
- Singh, R., Kumar, R., Farina, I., Colangelo, F., Feo, L., & Fraternali, F. (2019). Multi-Material Additive Manufacturing of Sustainable Innovative Materials and Structures. Polymers. https://doi.org/10.3390/polym11010062
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.