A Review of Equivalent Circuit Model Based Online State of Power Estimation for Lithium-Ion Batteries in Electric Vehicles
Open accessThe DOI matches its Crossref record; 92 of the 93 references it cites were found in a registry or an index.
Abstract
With rapid transportation electrification worldwide, lithium-ion batteries have gained much attention for energy storage in electric vehicles (EVs). State of power (SOP) is one of the key states of lithium-ion batteries for EVs to optimise power flow, thereby requiring accurate online estimation. Equivalent circuit model (ECM)-based methods are considered as the mainstream technique for online SOP estimation. They primarily vary in their basic principle, technical contribution, and validation approach, which have not been systematically reviewed. This paper provides an overview of the improvements on ECM-based online SOP estimation methods in the past decade. Firstly, online SOP estimation methods are briefed, in terms of different operation modes, and their main pros and cons are also analysed accordingly. Secondly, technical contributions are reviewed from three aspects: battery modelling, online parameters identification, and SOP estimation. Thirdly, SOP testing methods are discussed, according to their accuracy and efficiency. Finally, the challenges and outlooks are presented to inspire researchers in this field for further developments in the future.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Te ECM is an electrical modeling representation simplifed by a circuit composed of simple passive electronic parts, such as capacitors, inductors, and resistors [51].”
Citations
Cites
Lithium Batteries: Status, Prospects and Future
Scrosati, B., & Garche, J. (2010) · Journal of Power Sources · doi:10.1016/j.jpowsour.2009.11.048 · Cited by 5,153
A comparative study of equivalent circuit models for Li-ion batteries
Hu, X., Li, S., & Peng, H. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.10.013 · Cited by 2,179 · cited 1×
“Referring to [16], from the same authors, 1-RC model with one-state hysteresis is found as the best choice for LiFePO4 batteries, amid 12 commonly used ECMs, which offsets a notable voltage hysteresis and alleviates the model error by 7.”
Hannan, M. A., Lipu, M. S. H., Hussain, A., & Mohamed, A. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.05.001 · Cited by 2,005
State estimation for advanced battery management: Key challenges and future trends
Hu, X., Feng, F., Liu, K., Zhang, L., Xie, J., & Liu, B. (2019) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2019.109334 · Cited by 857
Technological Developments in Batteries: A Survey of Principal Roles, Types, and Management Needs
Hu, X., Zou, C., Zhang, C., & Li, Y. (2017) · IEEE Power and Energy Magazine · doi:10.1109/mpe.2017.2708812 · Cited by 561
Shen, P., Ouyang, M., Lu, L., Li, J., & Feng, X. (2018) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2017.2751613 · Cited by 534 · cited 1×
“In [36], a multi-state estimation framework of SOC, SOH, and instantaneous SOP was developed for lithium-ion batteries in EVs.”
Hu, X., Yuan, H., Zou, C., Li, Z., & Zhang, L. (2018) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2018.2865664 · Cited by 532
Xiong, R., Sun, F., Chen, Z., & He, H. (2014) · Applied Energy · doi:10.1016/j.apenergy.2013.07.061 · Cited by 529
Lai, X., Zheng, Y., & Sun, T. (2018) · Electrochimica Acta · doi:10.1016/j.electacta.2017.10.153 · Cited by 484
Wang, X., Wei, X., Zhu, J., Dai, H., Zheng, Y., Xu, X., & Chen, Q. (2021) · eTransportation · doi:10.1016/j.etran.2020.100093 · Cited by 451
High-Performance Battery-Pack Power Estimation Using a Dynamic Cell Model
Plett, G. L. (2004) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2004.832408 · Cited by 290 · cited 1×
“Plett first applied a lumped ECM to describe OCV variation for online SOP estimation [10].”
MethodA Novel Fractional Order Model for State of Charge Estimation in Lithium Ion Batteries
Xiong, R., Tian, J., Shen, W., & Sun, F. (2019) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2018.2880085 · Cited by 288
Self-citationA Double-Scale, Particle-Filtering, Energy State Prediction Algorithm for Lithium-Ion Batteries
Xiong, R., Zhang, Y., He, H., Zhou, X., & Pecht, M. G. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2017.2733475 · Cited by 285
Feng, T., Yang, L., Zhao, X., Zhang, H., & Qiang, J. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.01.154 · Cited by 285 · cited 3×
“1-RC model with a moving average noise [25].”
BackgroundMethodInfluentialTian, J., Xiong, R., & Yu, Q. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2798606 · Cited by 267
A hybrid statistical data-driven method for on-line joint state estimation of lithium-ion batteries
Song, Y., Liu, D., Liao, H., & Peng, Y. (2020) · Applied Energy · doi:10.1016/j.apenergy.2019.114408 · Cited by 266
Hannan, M. A., Lipu, M. S. H., Hussain, A., Ker, P. J., Mahlia, T. M. I., Mansor, M., Ayob, A., Saad, M. H., & Dong, Z. Y. (2020) · Scientific Reports · doi:10.1038/s41598-020-61464-7 · Cited by 244
Lin, C., Mu, H., Xiong, R., & Shen, W. (2016) · Applied Energy · doi:10.1016/j.apenergy.2016.01.010 · Cited by 217
Self-citationFarmann, A., & Sauer, D. U. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.08.031 · Cited by 217 · cited 2×
“To date, SOP estimation techniques mainly fall into two groups: characteristic mapping (CM)-based methods and equivalent circuit model (ECM)-based methods [9].”
BackgroundMethodElectrode ageing estimation and open circuit voltage reconstruction for lithium ion batteries
Tian, J., Xiong, R., Shen, W., & Sun, F. (2021) · Energy Storage Materials · doi:10.1016/j.ensm.2021.02.018 · Cited by 216
Self-citationXiong, R., He, H., Sun, F., Liu, X., & Liu, Z. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.12.003 · Cited by 204
Model-based dynamic multi-parameter method for peak power estimation of lithium–ion batteries
Sun, F., Xiong, R., He, H., Li, W., & Aussems, J. E. E. (2012) · Applied Energy · doi:10.1016/j.apenergy.2012.02.061 · Cited by 191 · cited 1×
“In the OLPM for online SOP estimation at a CC mode, a battery is supposed to continuously operate at constant current throughout a prediction window [11].”
MethodDevelopment of a universal modeling tool for rechargeable lithium batteries
Dubarry, M., & Liaw, B. Y. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.06.157 · Cited by 186 · cited 1×
“Compared with the 1-RC model, the DP model takes advantage of two RC networks with different time constants to describe the charge transfer process and double-layer effect at the mid frequency region, as well as the diffusion phenomenon at the low frequency region, thereby showing the improved model accuracy over basi…”
MethodAn enhanced multi-state estimation hierarchy for advanced lithium-ion battery management
Hu, X., Jiang, H., Feng, F., & Liu, B. (2020) · Applied Energy · doi:10.1016/j.apenergy.2019.114019 · Cited by 186
Zhang, W., Shi, W., & Ma, Z. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.04.148 · Cited by 178 · cited 1×
“In [65], SOE completely supersedes SOC to act as a constraint in SOP estimation.”
BackgroundFarmann, A., & Sauer, D. U. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.05.066 · Cited by 171 · cited 4×
“In [44], the authors compare the model accuracy of seven ECMs with a number of RC or RCCPE networks, ranging from 0 to 3, under different operating conditions.”
BackgroundMethodInfluentialSun, F., Xiong, R., & He, H. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.095 · Cited by 162 · cited 3×
“Battery SOP is determined once battery terminal voltage reaches its lower (or upper) cut-off value, namely Ut,k+L = Ut,min (or Ut,max) [12].”
BackgroundInfluentialLing, L., & Wei, Y. (2021) · IEEE Access · doi:10.1109/access.2021.3068813 · Cited by 154
Tan, X., Zhan, D., Lyu, P., Rao, J., & Fan, Y. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.229233 · Cited by 153
Jiao, R., Peng, K., & Dong, J. (2020) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2020.2996004 · Cited by 146
Tran, M.-K., Akinsanya, M., Panchal, S., Fraser, R., & Fowler, M. (2020) · Vehicles · doi:10.3390/vehicles3010002 · Cited by 145 · cited 1×
“Transportation electrification, such as electric vehicles (EVs), is a clean solution to the replacement of traditional internal combustion engine vehicles for tailpipe emissions reduction [1].”
BackgroundLai, X., He, L., Wang, S., Zhou, L., Zhang, Y., Sun, T., & Zheng, Y. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.120203 · Cited by 144
Comprehensive dynamic battery modeling for PHEV applications
Zhang, H., & Chow, M.-Y. (2010) · IEEE PES General Meeting · doi:10.1109/pes.2010.5590108 · Cited by 143
Online Estimation of Power Capacity With Noise Effect Attenuation for Lithium-Ion Battery
Wei, Z., Zhao, J., Xiong, R., Dong, G., Pou, J., & Tseng, K. J. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2878122 · Cited by 143 · cited 1×
“In [52], the authors emphasize that the unexpected sensing noises in current and voltage signals may cause biased parameters identification and further affect SOC and SOP estimation accuracy.”
BackgroundZhang, X., Wang, Y., Wu, J., & Chen, Z. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.02.117 · Cited by 140 · cited 1×
“In [58], a particle swarm optimisation (PSO) algorithm is employed in online parameters identification for SOP estimation.”
MethodXiong, R., He, H., Sun, F., & Zhao, K. (2012) · Energies · doi:10.3390/en5051455 · Cited by 137
Particle-filtering-based estimation of maximum available power state in Lithium-Ion batteries
Burgos-Mellado, C., Orchard, M. E., Kazerani, M., Cárdenas, R., & Sáez, D. A. (2015) · Applied Energy · doi:10.1016/j.apenergy.2015.09.092 · Cited by 133 · cited 1×
“In [30], a multi-dependent Rint model, as shown in Figure 12, is constructed for online instantaneous SOP estimation that considers the effects of SOC and current on the internal resistance.”
MethodHu, X., Xiong, R., & Egardt, B. (2014) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2013.2284713 · Cited by 127 · cited 2×
“A straightforward strategy to determine the representative cell in a battery pack is proposed in [20,72] by comparing the peak cell currents in a prediction window.”
BackgroundMethodZhang, W., Wang, L., Wang, L., Liao, C., & Zhang, Y. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3073359 · Cited by 124 · cited 1×
“In [55], to jointly estimate battery model parameters and state variables, while considering current dependency on charge transfer resistance, the fully-polarised internal resistance is calibrated at various current amplitudes and treated as an observation in an unscented KF (UKF).”
MethodDong, G., Wei, J., & Chen, Z. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.08.065 · Cited by 123 · cited 3×
“1-RC model considering self-discharge phenomenon [24] • Enhance the model robustness against battery calendar aging and cycling aging • Require a mass of data to establish battery aging model • Lack of robustness under different driving experience”
BackgroundMethodInfluentialAdaptive on-line prediction of the available power of lithium-ion batteries
Waag, W., Fleischer, C., & Sauer, D. U. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.05.111 · Cited by 113 · cited 4×
“Consider parameter dependencies 1-RC model incorporating Bulter-Volmer equation [26,27] • Enhance the model accuracy against current effect • Largely increase model complexity • Increase computational cost in SOP estimation”
BackgroundMethodInfluentialPei, L., Zhu, C., Wang, T., Lu, R., & Chan, C. C. (2014) · Energy · doi:10.1016/j.energy.2014.02.009 · Cited by 109 · cited 3×
“In [14,37], both battery model parameterization and online SOC estimation are implemented using a dual EKF (DEKF) algorithm.”
MethodLao, Z., Xia, B., Wang, W., Sun, W., Lai, Y., & Wang, M. (2018) · Energies · doi:10.3390/en11061358 · Cited by 106
Power prediction from a battery state estimator that incorporates diffusion resistance
Wang, S., Verbrugge, M. W., Wang, J. S., & Liu, P. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.04.070 · Cited by 99
State of power estimation of lithium-ion battery based on fractional-order equivalent circuit model
Liu, C., Hu, M., Jin, G., Xu, Y., & Zhai, J. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102954 · Cited by 98 · cited 3×
“2-RC fractional-order model with a Warburg element [43] • High model accuracy • High model complexity • High computational cost”
BackgroundMethodInfluentialWaag, W., Fleischer, C., & Sauer, D. U. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.03.034 · Cited by 97
Xiong, R., Wang, J., Shen, W., Tian, J., & Mu, H. (2021) · Engineering · doi:10.1016/j.eng.2020.10.022 · Cited by 97
Self-citationShu, X., Li, G., Shen, J., Lei, Z., Chen, Z., & Liu, Y. (2020) · Energy · doi:10.1016/j.energy.2020.118262 · Cited by 97 · cited 1×
“A similar SOH update mechanism is also applied in [39].”
MethodZou, C., Klintberg, A., Wei, Z., Fridholm, B., Wik, T., & Egardt, B. (2018) · Journal of Power Sources · doi:10.1016/j.jpowsour.2018.06.034 · Cited by 96 · cited 2×
“In [34,38], a DP model is associated with a two-state thermal model to reproduce battery electrical and thermal dynamics.”
BackgroundMethodWang, Y., Pan, R. N., Liu, C., Chen, Z., & Ling, Q. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.11.019 · Cited by 91 · cited 1×
“In [21], multi-state estimation algorithms, including SOC, SOE, and SOP, are presented, based on a 1-RC model with hysteresis.”
MethodYang, L., Cai, Y., Yang, Y., & Deng, Z. (2020) · Applied Energy · doi:10.1016/j.apenergy.2019.114006 · Cited by 90 · cited 4×
“In [29], an improved 1-RC model with multi-dependent OCV, as shown in Figure 11, is established for SOP estimation, in order to compensate the distortion phenomenon of OCV–SOC curve.”
MethodInfluentialElectric vehicles, primary energy sources and CO2 emissions: Romanian case study
Varga, B. O. (2012) · Energy · doi:10.1016/j.energy.2012.10.036 · Cited by 85
Zheng, F., Jiang, J., Sun, B., Zhang, W., & Pecht, M. (2016) · Energy · doi:10.1016/j.energy.2016.06.010 · Cited by 83 · cited 2×
“Besides, an empiricallyderived temperature correction term is devised in [31] to further facilitate model robustness at extreme temperatures, which guarantees 95% confidence interval in instantaneous SOP estimation from −20 ◦C to 50 ◦C.”
BackgroundMethodTang, X., Wang, Y., Yao, K., He, Z., & Gao, F. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.227141 · Cited by 83 · cited 2×
“In [28], a so-called migrated 1-RC model, as shown in Figure 10, is proposed to improve the robustness of SOP estimation against uncertainties from battery aging and temperature variation, where the model parameters are all characterized as three-dimensional surfaces of SOC and temperature.”
MethodLi, X., Xu, J., Hong, J., Tian, J., & Tian, Y. (2020) · Energy · doi:10.1016/j.energy.2020.118858 · Cited by 83 · cited 1×
“For a battery pack comprising of only serial-connected cells, pack-level SOP depends on the representative cell that first reaches any of the pre-set constraints [71].”
BackgroundMalysz, P., Ye, J., Gu, R., Yang, H., & Emadi, A. (2016) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2015.2443975 · Cited by 77 · cited 1×
“In [61], the authors stated that the first-order Taylor series expansion may yield unrealistic estimations of model parameters (e.”
BackgroundLu, J., Chen, Z., Yang, Y., & L.V., M. (2018) · IEEE Access · doi:10.1109/access.2018.2824559 · Cited by 74 · cited 1×
“To further engage all model parameters in forward prediction, the same authors employed a genetic algorithm (GA) to work out the peak discharge and charge currents from a highly nonlinear function; additionally, the effects of erroneous SOC and battery aging on SOP estimation were systematically analysed [60].”
MethodNiri, M. F., Truong, D. Q., Yu, T. F., Marco, J., & Truong, B. N. M. (2020) · IEEE Transactions on Intelligent Transportation Systems · doi:10.1109/tits.2020.3028024 · Cited by 73
Rahimifard, S., Ahmed, R., & Habibi, S. R. (2021) · IEEE Access · doi:10.1109/access.2021.3102607 · Cited by 72 · cited 1×
“In [67], the multi-state estimation algorithm, with respect to SOC, SOH, and SOP, was proposed, primarily based on the mixed SOH estimation strategy.”
MethodWang, S., Verbrugge, M. W., Wang, J. S., & Liu, P. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.06.078 · Cited by 70 · cited 2×
“In the OLPM for online SOP estimation at a CV mode, a battery is forced to continuously operate at its lower (or upper) cut-off voltage throughout a prediction window [13].”
MethodHua, X., Zhang, C., & Offer, G. J. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.229117 · Cited by 70
Esfandyari, M. J., Hairi Yazdi, M. R., Esfahanian, V., Masih-Tehrani, M., Nehzati, H., & Shekoofa, O. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2019.100758 · Cited by 68 · cited 1×
“In [63,64], a fuzzy logic controller is designed to prevent batteries from breaching the pre-set constraints and”
BackgroundEsfandyari, M. J., Esfahanian, V., Hairi Yazdi, M. R., Nehzati, H., & Shekoofa, O. (2019) · Energy · doi:10.1016/j.energy.2019.03.176 · Cited by 63 · cited 1×
“In [63,64], a fuzzy logic controller is designed to prevent batteries from breaching the pre-set constraints and”
BackgroundNaaz, F., Herle, A., Channegowda, J., Raj, A., & Lakshminarayanan, M. (2021) · International Journal of Energy Research · doi:10.1002/er.7013 · Cited by 62
Tang, X., Yao, K., Liu, B., Hu, W., & Gao, F. (2018) · Energies · doi:10.3390/en11010086 · Cited by 61 · cited 1×
“In [69], a model-based extreme learning machine (ELM) algorithm was derived to predict battery future power capability, voltage, and temperature against varying SOC and temperature.”
MethodOnline Battery State of Power Prediction Using PRBS and Extended Kalman Filter
Nejad, S., & Gladwin, D. T. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2019.2921280 · Cited by 61 · cited 2×
“In [14,37], both battery model parameterization and online SOC estimation are implemented using a dual EKF (DEKF) algorithm.”
MethodZhang, T., Guo, N., Sun, X., Fan, J., Yang, N., Song, J., & Zou, Y. (2021) · Sustainability · doi:10.3390/su13095166 · Cited by 53 · cited 1×
“Another multi-state estimation framework of SOC, SOH, and SOP is proposed in [66], where SOH will be updated quarterly or semi-annually, based on the charge accumulation between two separate SOCs.”
BackgroundZhang, J., Wang, P., Liu, Y., & Cheng, Z. (2021) · Energies · doi:10.3390/en14030769 · Cited by 51
Jiang, J., Liu, S., Ma, Z., Wang, L. Y., & Wu, K. (2016) · Energy · doi:10.1016/j.energy.2016.10.087 · Cited by 47 · cited 3×
“Consider parameter dependencies 1-RC model incorporating Bulter-Volmer equation [26,27] • Enhance the model accuracy against current effect • Largely increase model complexity • Increase computational cost in SOP estimation”
BackgroundMethodLi, Z., Shi, X., Shi, M., Wei, C., Di, F., & Sun, H. (2020) · Asia Energy and Electrical Engineering Symposium (AEEES) · doi:10.1109/aeees48850.2020.9121487 · Cited by 46
State of Power Prediction for Battery Systems With Parallel-Connected Units
Han, W., Altaf, F., Zou, C., & Wik, T. (2021) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2021.3101242 · Cited by 45 · cited 2×
“To ensure the safety and durability of lithium-ion batteries in EV applications, battery management systems (BMSs) are equipped to monitor battery states [5].”
BackgroundMethodWang, L., Cheng, Y., & Zou, J. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.03.091 · Cited by 41
Juang, L. W., Kollmeyer, P. J., Jahns, T. M., & Lorenz, R. D. (2012) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2012.6342591 · Cited by 40 · cited 1×
“In [54], battery OCV is treated as a state variable instead of SOC in this algorithm to provide the basis for SOP estimation, and an offline calibrated curve, in relation to the rate of OCV change per ampere-hour, is employed to achieve close-loop compensation.”
MethodData pieces-based parameter identification for lithium-ion battery
Gao, W., Zou, Y., Sun, F., Hu, X., Yu, Y., & Feng, S. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.08.018 · Cited by 39 · cited 1×
“By far, online parameter identification techniques can be divided into two main groups: recursive and non-recursive methods [46].”
BackgroundPeak power prediction for series-connected LiNCM battery pack based on representative cells
Zhou, Z., Kang, Y., Shang, Y., Cui, N., Zhang, C., & Duan, B. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.05.144 · Cited by 37 · cited 2×
“In [56], cell parameters and SOCs in a battery pack are concurrently estimated through a dual adaptive EKF (DAEKF) algorithm, which has a stronger convergence capability than EKF algorithm by regressing noise covariance iteratively.”
MethodLithium-Ion Battery Online Rapid State-of-Power Estimation under Multiple Constraints
Shun, X., Hu, G., Huang, R., Guo, F., & Zhou, P. (2018) · Energies · doi:10.3390/en11020283 · Cited by 34
Tan, Y., Luo, M., She, L., & Cui, X. (2020) · International Journal of Electrochemical Science · doi:10.20964/2020.02.34 · Cited by 34
Online Reliable Peak Charge/Discharge Power Estimation of Series-Connected Lithium-Ion Battery Packs
Jiang, B., Dai, H., Wei, X., Zhu, L., & Sun, Z. (2017) · Energies · doi:10.3390/en10030390 · Cited by 33 · cited 2×
“, cell capacity and ohmic resistance) in representative cell selection [27,47].”
BackgroundMethodSelf-learning state-of-available-power prediction for lithium-ion batteries in electrical vehicles
Fleischer, C., Waag, W., Bai, Z., & Sauer, D. U. (2012) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2012.6422670 · Cited by 23 · cited 1×
“In [68], a self-learning estimation algorithm was proposed for SOP estimation, based on an adaptive neuro-fuzzy inference system (ANFIS).”
MethodEstimation of Real-Time Peak Power Capability of a Traction Battery Pack Used in an HEV
Zhang, C., Zhang, C., & Sharkh, S. M. (2010) · Asia-Pacific Power and Energy Engineering Conference (APPEEC) · doi:10.1109/appeec.2010.5448755 · Cited by 22 · cited 1×
“A straightforward strategy to determine the representative cell in a battery pack is proposed in [20,72] by comparing the peak cell currents in a prediction window.”
MethodResearch on peak power test method for Lithium Ion battery
Xiaofeng, S., Sun, B., Qi, H., Shen, X., & Su, X. (2018) · Energy Procedia · doi:10.1016/j.egypro.2018.09.209 · Cited by 20
Multi-Level Energy Management for Hybrid Electric Vehicles—Part I
van Reeven, V., & Hofman, T. (2019) · Vehicles · doi:10.3390/vehicles1010002 · Cited by 20
Lipu, M. S. H., Hannan, M. A., Hussain, A., Saad, M. H. M., Ayob, A., & Muttaqi, K. M. (2019) · 2019 IEEE Industry Applications Society Annual Meeting · doi:10.1109/ias.2019.8912322 · Cited by 19
Li, B., Wang, S., Fernández, C., Yu, C., Xia, L., & Fan, Y. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102583 · Cited by 18 · cited 1×
“In [51], an improved AFFLS algorithm is developed to achieve preferable performance in processing fluctuated data, while simplifying preliminary experimental analysis and data fitting, thereby enhancing its”
MethodA New Method of State of Peak Power Capability Prediction for Li-Ion Battery
Li, X., Sun, J., Hu, Z., Lu, R., Zhu, C., & Wu, G. (2015) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2015.7352880 · Cited by 12 · cited 4×
“In [41], a fractional KF algorithm is employed to realise the joint estimation of battery states and model parameters of a simplified fractional order model, where the state covariance prediction is associated with the previous state in a memory horizon, instead of only the last one.”
BackgroundMethodInfluentialOnline estimation of state of power for lithium-ion battery considering the battery aging
Chen, Z., Lu, J., Yang, Y., & Xiong, R. (2017) · Chinese Automation Congress · doi:10.1109/cac.2017.8243310 · Cited by 11 · cited 1×
“In [59], the ohmic resistance of a 1-RC model is predicted forward in a prediction window using the first-order Taylor series expansion.”
MethodZheng, L., Zhu, J. G., Wang, G., Lu, D. D., McLean, P., & He, T. (2017) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems.2017.8056426 · Cited by 9 · cited 1×
“In [31,32], the thermal effect on battery instantaneous SOP is investigated based on a multi-dependent Rint model.”
MethodExperimental investigation of state‐of‐power measurement for lithium‐ion batteries
Jin, C., Sun, Y., Zheng, Y., Yang, X., Lai, X., Gu, H., & Feng, X. (2020) · International Journal of Energy Research · doi:10.1002/er.6337 · Cited by 8
Online estimation of battery power state based on improved equivalent circuit model
Wang, Y. (2021) · IOP Conference Series Earth and Environmental Science · doi:10.1088/1755-1315/651/2/022080 · Cited by 8 · cited 2×
“Linear regression model [33] • Low computational cost • Model accuracy depends on the length of previous state”
BackgroundMethodMulti-Level Energy Management—Part II: Implementation and Validation
van Reeven, V., & Hofman, T. (2019) · Vehicles · doi:10.3390/vehicles1010003 · Cited by 7
Predictive Model Based Battery Constraints for Electric Motor Control within EV Powertrains
Rosca, B., Wilkins, S., Jacob, J., Hoedemaekers, E., & van den Hoek, S. P. (2014) · IEEE International Electric Vehicle Conference · doi:10.1109/ievc.2014.7056166 · Cited by 5
Wei, C., & Benosman, M. (2016) · International Conference on Renewable Energy Research and Applications (ICRERA) · doi:10.1109/icrera.2016.7884376 · Cited by 5 · cited 1×
“Additionally, the extremum seeking algorithm, as another typical recursive method, is employed in [22] to characterize model parameters for instantaneous SOP estimation, where a sinusoidal current signal is imposed on a battery system to generate a cost function.”
Method
Research works printed but not linked: 2
- Podlubny, I. (1998). Fractional Differential Equations: An. Introduction to Fractional Derivatives, Fractional Differential Equations, to Methods of Their Solution and Some of Their Applications, Elsevier.
- Plett, G.L. (2005, January 2–6). Dual and Joint EKF for Simultaneous SOC and SOH Estimation. Proceedings of the 21st Electric Vehicle Symposium (EVS21), Monte Carlo, Monaco.
Cited by
Review of battery state estimation methods for electric vehicles-Part II: SOH estimation
Demirci, O., Taskin, S., Schaltz, E., & Acar Demirci, B. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.112703 · Cited by 231
Review on Modeling and SOC/SOH Estimation of Batteries for Automotive Applications
Dini, P., Colicelli, A., & Saponara, S. (2024) · Batteries · doi:10.3390/batteries10010034 · Cited by 166
Recent advances in model-based fault diagnosis for lithium-ion batteries: A comprehensive review
Xu, Y., Ge, X., Guo, R., & Shen, W. (2024) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2024.114922 · Cited by 163
Self-citationTekin, M., & Karamangil, M. İ. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111327 · Cited by 142
Guo, R., & Shen, W. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2022.3220881 · Cited by 104
“Whereas, SOP refers to the peak power capability of LIBs that could release to or accept from an EV powertrain in a specified prediction window [6] which plays a key role in energy management optimization and driving strategy selection [7].”
BackgroundSelf-citation
Metadata
- Authors
- Guo, R., & Shen, W.
- Affiliations
- Swinburne University of Technology (AU)
- Corresponding author
- Shen, Weixiang
- Venue
- Vehicles
- Publisher
- MDPI AG
- Published
- 2021-12-21
- Volume
- 4
- Issue
- 1
- Pages
- 1-29
- ISSN
- 2624-8921 (ISSN-L)
- OpenAlex
- W4200237397
- Cited by
- 121
- References
- 93
- Citations by year
- 2026: 21 · 2025: 34 · 2024: 31 · 2023: 23 · 2022: 12
- FWCI
- 5.36
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Vehicles (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Australian Government
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Keywords
- lithium-ion batteries, electric vehicles, state of power estimation, equivalent circuit model, online parameter estimation, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.