CoChat
Sign Up
Cited by 37Advanced machining processes and optimizationEngineering Technology and MethodologiesMetal Alloys Wear and Properties

The DOI matches its Crossref record.

Tool Wear Progression and its Effect on Energy Consumption in Turning of Titanium Alloy (Ti-6Al-4V)

Open access
Younas, Muhammad, Jaffery, Syed Husain Imran, Khan, Mushtaq, Ahmad, Riaz, Ali, Liaqat, Khan, Zarak, Khan, Aftab·2019·Mechanical Sciences
DOI 10.5194/ms-10-373-2019
Open this paper in CoChat — free accountOpen PDF

Abstract

To achieve greater productivity, titanium alloy requires cutting at higher speeds (above 100 m min −1 ) that affects the tool life and energy consumption during the machining process. This research work correlates the wear progression and Specific Cutting Energy (SCE) in turning Ti-6Al-4V alloy using H13 tools (uncoated carbide) in dry conditions from low to high cutting speeds. Cutting condition employed in this study were selected from published wear map developed for titanium (Ti-6Al-4V alloy) with the same tool. Flank wear growth of the tool has been investigated at different length of cuts in correlation with the SCE under different cutting conditions. The useful tool life was found to be shorter at high-speed machining conditions, thus the end of useful tool life criteria (ISO 3685) was reached at a much shorter length of cuts as compared to low-speed machining conditions. The cutting conditions corresponding to high wear rate also resulted in high SCE. Finally, SCE and wear have been related by a linear relationship that can be used to monitor wear and/or SCE utilization during machining. The results help in the selection of appropriate cutting conditions that will enhance the tool life and minimize SCE consumption during machining titanium alloy.

Overview

Integrity signals

Registry

Crossref · 10.5194/ms-10-373-2019

Cites

Statistics

Recomputing p-values needs the paper’s full text.

Verification

Claims the paper makes

We couldn’t retrieve this paper’s full text, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Citations

Cites

No references could be resolved yet.

Research works printed but not linked: 32

  1. Arrazola, P. J., Garay, A., Iriarte, L. M., Armendia, M., Marya, S., and Le Maitre, F.: Machinability of titanium alloys (Ti6Al4V and Ti555.3), J. Mater. Process. Tech., 209, 2223–2230, 10.1016/j.jmatprotec.2008.06.020, 2009. · DOI
  2. Balogun, V. A. and Mativenga, P. T.: Impact of un-deformed chip thickness on specific energy in mechanical machining processes, J. Clean. Prod., 69, 260–268, 2014. · DOI
  3. Balogun, V. A., Gu, H., and Mativenga, P. T.: Improving the integrity of specific cutting energy coefficients for energy demand modelling, P. I. Mech. Eng. B-J. Eng., 229, 2109–2117, 2015. · DOI
  4. Behrendt, T., Zein, A., and Min, S.: Development of an energy consumption monitoring procedure for machine tools, Cirp Ann.-Manuf. Techn., 61, 43–46, 10.1016/j.cirp.2012.03.103, 2012. · DOI
  5. Bermingham, M. J., Kirsch, J., Sun, S., Palanisamy, S., and Dargusch, M. S.: New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V, Int. J. Mach. Tool Manu., 51, 500–511, 10.1016/j.ijmachtools.2011.02.009, 2011. · DOI
  6. Deng, J. X., Li, Y. S., and Song, W. L.: Diffusion wear in dry cutting of Ti-6Al-4V with WC/Co carbide tools, Wear, 265, 1776–1783, 10.1016/j.wear.2008.04.024, 2008. · DOI
  7. Ezugwu, E. O., Bonney, J., and Yamane, Y.: An overview of the machinability of aeroengine alloys, J Mater Process Tech, 134, 233–253, 10.1016/S0924-0136(02)01042-7, 2003. · DOI
  8. Fan, Y. H., Hao, Z. P., Zheng, M. L., and Yang, S. C.: Wear characteristics of cemented carbide tool in dry-machining Ti-6Al-4V, Mach. Sci. Technol., 20, 249–261, 2016. · DOI
  9. Gupta, M. K., Sood, P. K., Singh, G., and Sharma, V. S.: Investigations of performance parameters in NFMQL assisted turning of titanium alloy using TOPSIS and particle swarm optimisation method, Int. J. Mater. Prod. Tec., 57, 299–321, 10.1504/Ijmpt.2018.095116, 2018. · DOI
  10. Hughes, J. I., Sharman, A. R. C., and Ridgway, K.: The effect of cutting tool material and edge geometry on tool life and workpiece surface integrity, P. I. Mech. Eng. B-J. Eng., 220, 93–107, 10.1243/095440506X78192, 2006. · DOI
  11. Jaffery, S. I. and Mativenga, P. T.: Assessment of the machinability of Ti-6Al-4V alloy using the wear map approach, Int. J. Adv. Manuf. Tech., 40, 687–696, 2009. · DOI · Paper page
  12. Jaffery, S. H. I. and Mativenga, P. T.: Wear mechanisms analysis for turning Ti-6Al-4V-towards the development of suitable tool coatings, Int. J. Adv. Manuf. Tech., 58, 479–493, 10.1007/s00170-011-3427-y, 2012. · DOI · Paper page
  13. Jaffery, S. H. I., Khan, M., Sheikh, N. A., and Mativenga, P.: Wear mechanism analysis in milling of Ti-6Al-4V alloy, P. I. Mech. Eng. B-J. Eng., 227, 1148–1156, 10.1177/0954405413481210, 2013. · DOI
  14. Jaffery, S. H. I., Khan, M., Ali, L., and Mativenga, P. T.: Statistical analysis of process parameters in micromachining of Ti-6Al-4V alloy, P. I. Mech. Eng. B-J. Eng., 230, 1017–1034, 10.1177/0954405414564409, 2016. · DOI
  15. Kaplan, B., Odelros, S., Kritikos, M., Bejjani, R., and Norgren, S.: Study of tool wear and chemical interaction during machining of Ti6Al4V, Int. J. Refract. Met. H., 72, 253–256, 10.1016/j.ijrmhm.2017.12.012, 2018. · DOI
  16. Kara, S. and Li, W.: Unit process energy consumption models for material removal processes, Cirp Ann.-Manuf. Techn., 60, 37–40, 10.1016/j.cirp.2011.03.018, 2011. · DOI
  17. Kumar, T. S., Ramanujam, R., Vignesh, M., Tamiloli, N., Sharma, N., Srivastava, S., and Patel, A.: Comparative evaluation of performances of TiAlN, AICrN, TiAlN/AlCrN coated carbide cutting tools and uncoated carbide cutting tools on turning Inconel 825 alloy using Grey Relational Analysis, Sensor Actuat. A-Phys., 279, 331–342, 10.1016/j.sna.2018.06.041, 2018. · DOI
  18. Kuram, E.: The effect of monolayer TiCN-, AlTiN-, TiAlN-and two layers TiCN plus TiN- and AlTiN plus TiN-coated cutting tools on tool wear, cutting force, surface roughness and chip morphology during high-speed milling of Ti6Al4V titanium alloy, P. I. Mech. Eng. B-J. Eng., 232, 1273–1286, 10.1177/0954405416666905, 2018. · DOI
  19. Li, A., Zhao, J., Luo, H., Pei, Z., and Wang, Z.: Progressive tool failure in high-speed dry milling of Ti-6Al-4V alloy with coated carbide tools, Int. J. Adv. Manuf. Tech., 58, 465–478, 10.1007/s00170-011-3408-1, 2012. · DOI
  20. Li, G. X., Yi, S., Wen, C. E., and Ding, S. L.: Wear Mechanism and Modeling of Tribological Behavior of Polycrystalline Diamond Tools When Cutting Ti6Al4V, J. Manuf. Sci. E.-T. ASME, 140, 121011, 10.1115/1.4041327, 2018a. · DOI
  21. Li, G. X., Li, N., Wen, C. E., and Ding, S. L.: Investigation and modeling of flank wear process of different PCD tools in cutting titanium alloy Ti6Al4V, Int. J. Adv. Manuf. Tech., 95, 719–733, 10.1007/s00170-017-1222-0, 2018b. · DOI
  22. Li, K. M. and Liang, S. Y.: Modeling of cutting temperature in near dry machining, J. Manuf. Sci. E.-T. ASME, 128, 416–424, 10.1115/1.2162907, 2006. · DOI
  23. Li, W. and Kara, S.: An empirical model for predicting energy consumption of manufacturing processes: a case of turning process, P. I. Mech. Eng. B-J. Eng., 225, 1636–1646, 2011. · DOI
  24. Mativenga, P. T., Rajemi, M. F., and Hinduja, S.: Calculation of optimum cutting parameters based on minimum energy footprint, Cirp Ann.-Manuf. Techn., 60, 149–152, 10.1016/j.cirp.2011.03.088, 2011. · DOI
  25. Revuru, R. S., Zhang, J. Z., Posinasetti, N. R., and Kidd, T.: Optimization of titanium alloys turning operation in varied cutting fluid conditions with multiple machining performance characteristics, Int. J. Adv. Manuf. Tech., 95, 1451–1463, 10.1007/s00170-017-1299-5, 2018. · DOI
  26. Shokrani, A., Dhokia, V., and Newman, S. T.: Energy conscious cryogenic machining of Ti-6Al-4V titanium alloy, P. I. Mech. Eng. B-J. Eng., 232, 1690–1706, 10.1177/0954405416668923, 2018. · DOI
  27. Sun, J. and Guo, Y. B.: A comprehensive experimental study on surface integrity by end milling Ti-6Al-4V, J. Mater. Process. Tech., 209, 4036–4042, 2009. · DOI
  28. Venugopal, K. A., Paul, S., and Chattopadhyay, A. B.: Tool wear in cryogenic turning of Ti-6Al-4V alloy, Cryogenics, 47, 12–18, 10.1016/j.cryogenics.2006.08.011, 2007a. · DOI
  29. Venugopal, K. A., Paul, S., and Chattopadhyay, A. B.: Growth of tool wear in turning of Ti-6Al-4V alloy under cryogenic cooling, Wear, 262, 1071–1078, 10.1016/j.wear.2006.11.010, 2007b. · DOI
  30. Warsi, S. S., Jaffery, S. H. I., Ahmad, R., Khan, M., Ali, L., Agha, M. H., and Akram, S.: Development of energy consumption map for orthogonal machining of Al 6061-T6 alloy, P. I. Mech. Eng. B-J. Eng., 232, 2510–2522, 10.1177/0954405417703424, 2018a. · DOI
  31. Warsi, S. S., Jaffery, S. H. I., Ahmad, R., Khan, M., Agha, M. H., and Ali, L.: Development and analysis of energy consumption map for high-speed machining of Al 6061-T6 alloy, Int. J. Adv. Manuf. Tech., 96, 91–102, 2018b. · DOI
  32. Zoya, Z. A. and Krishnamurthy, R.: The performance of CBN tools in the machining of titanium alloys, J. Mater. Process. Tech., 100, 80–86, 10.1016/S0924-0136(99)00464-1, 2000. · DOI

Cited by

Sorted by citations

See all 37

Metadata

Authors
Younas, M., Jaffery, S. H. I., Khan, M., Ahmad, R., Ali, L., Khan, Z., & Khan, A.
Affiliations
  • National University of Sciences and Technology (PK)
  • University of Technology Nowshera (PK)
  • University of Engineering and Technology Peshawar (PK)
Corresponding author
  • Younas, Muhammad
  • Khan, Mushtaq
ORCID
Venue
Mechanical Sciences
Publisher
Copernicus GmbH
Published
2019-07-18
Volume
10
Issue
2
Pages
373-382
ISSN
  • 2191-9151 (ISSN-L)
  • 2191-916X
DOI
10.5194/ms-10-373-2019
OpenAlex
W2957389487
Cited by
37
References
0
Citations by year
2026: 1 · 2025: 4 · 2024: 8 · 2023: 10 · 2022: 4 · 2021: 6 · 2020: 3 · 2019: 1
FWCI
1.97
Type
journal article
Language
en
Open access
Licence
Locations
  • Mechanical sciences (publishedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
  • Open Access Institutional Repository at Robert Gordon University (Robert Gordon University) (submittedVersion, cc-by)
  • Greater South Information System
Topics
  • Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
  • Physical Sciences › Materials Science › Metals and Alloys › Metal Alloys Wear and Properties
Keywords
tool wear, specific cutting energy, Ti-6Al-4V, titanium alloy turning, flank wear, tool life, cutting speed, dry machining, wear maps, wear rate, machining energy consumption

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Tool Wear Progression and its Effect on Energy Consumption in Turning of Titanium Alloy (Ti-6Al-4V). https://app.cochat.ai/papers/10.5194/ms-10-373-2019
The paper
Younas, M., Jaffery, S. H. I., Khan, M., Ahmad, R., Ali, L., Khan, Z., & Khan, A. (2019). Tool Wear Progression and its Effect on Energy Consumption in Turning of Titanium Alloy (Ti-6Al-4V). Mechanical Sciences. https://doi.org/10.5194/ms-10-373-2019