The DOI matches its Crossref record; 23 of the 23 references it cites were found in a registry or an index.
EGaIn‐Assisted Room‐Temperature Sintering of Silver Nanoparticles for Stretchable, Inkjet‐Printed, Thin‐Film Electronics
Abstract
Coating inkjet‐printed traces of silver nanoparticle (AgNP) ink with a thin layer of eutectic gallium indium (EGaIn) increases the electrical conductivity by six‐orders of magnitude and significantly improves tolerance to tensile strain. This enhancement is achieved through a room‐temperature “sintering” process in which the liquid‐phase EGaIn alloy binds the AgNP particles (≈100 nm diameter) to form a continuous conductive trace. Ultrathin and hydrographically transferrable electronics are produced by printing traces with a composition of AgNP‐Ga‐In on a 5 µm‐thick temporary tattoo paper. The printed circuit is flexible enough to remain functional when deformed and can support strains above 80% with modest electromechanical coupling (gauge factor ≈1). These mechanically robust thin‐film circuits are well suited for transfer to highly curved and nondevelopable 3D surfaces as well as skin and other soft deformable substrates. In contrast to other stretchable tattoo‐like electronics, the low‐cost processing steps introduced here eliminate the need for cleanroom fabrication and instead requires only a commercial desktop printer. Most significantly, it enables functionalities like “electronic tattoos” and 3D hydrographic transfer that have not been previously reported with EGaIn or EGaIn‐based biphasic electronics.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Kim, D.-H., Lu, N., Ma, R., Kim, Y.-S., Kim, R.-H., Wang, S., Wu, J., Won, S. M., Tao, H., Islam, A., et al. (2011) · Science · doi:10.1126/science.1206157 · Cited by 4,836
An ultra-lightweight design for imperceptible plastic electronics
Kaltenbrunner, M., Sekitani, T., Reeder, J., Yokota, T., Kuribara, K., Tokuhara, T., Drack, M., Schwödiauer, R., Graz, I., Bauer-Gogonea, S., et al. (2013) · Nature · doi:10.1038/nature12314 · Cited by 2,485
Stretchable and Soft Electronics using Liquid Metals
Dickey, M. D. (2017) · Advanced Materials · doi:10.1002/adma.201606425 · Cited by 1,776
Ultrathin conformal devices for precise and continuous thermal characterization of human skin
Webb, R. C., Bonifas, A. P., Behnaz, A., Zhang, Y., Yu, K. J., Cheng, H., Shi, M., Bian, Z., Liu, Z., Kim, Y.-S., et al. (2013) · Nature Materials · doi:10.1038/nmat3755 · Cited by 1,229
Printable elastic conductors with a high conductivity for electronic textile applications
Matsuhisa, N., Kaltenbrunner, M., Yokota, T., Jinno, H., Kuribara, K., Sekitani, T., & Someya, T. (2015) · Nature Communications · doi:10.1038/ncomms8461 · Cited by 869
Multifunctional Epidermal Electronics Printed Directly Onto the Skin
Yeo, W., Kim, Y., Lee, J., Ameen, A., Shi, L., Li, M., Wang, S., Ma, R., Jin, S. H., Kang, Z., et al. (2013) · Advanced Materials · doi:10.1002/adma.201204426 · Cited by 828
Highly Sensitive Skin‐Mountable Strain Gauges Based Entirely on Elastomers
Lu, N., Lu, C., Yang, S., & Rogers, J. (2012) · Advanced Functional Materials · doi:10.1002/adfm.201200498 · Cited by 825
Printable elastic conductors by in situ formation of silver nanoparticles from silver flakes
Matsuhisa, N., Inoue, D., Zalar, P., Jin, H., Matsuba, Y., Itoh, A., Yokota, T., Hashizume, D., & Someya, T. (2017) · Nature Materials · doi:10.1038/nmat4904 · Cited by 750
Inkjet printing of nanosized silver colloids
Lee, H.-H., Chou, K.-S., & Huang, K.-C. (2005) · Nanotechnology · doi:10.1088/0957-4484/16/10/074 · Cited by 586
Soft Multifunctional Composites and Emulsions with Liquid Metals
Kazem, N., Hellebrekers, T., & Majidi, C. (2017) · Advanced Materials · doi:10.1002/adma.201605985 · Cited by 404
Self-citationConductive Inks with a “Built-In” Mechanism That Enables Sintering at Room Temperature
Grouchko, M., Kamyshny, A., Mihailescu, C. F., Anghel, D. F., & Magdassi, S. (2011) · ACS Nano · doi:10.1021/nn2005848 · Cited by 331
EGaIn–Metal Interfacing for Liquid Metal Circuitry and Microelectronics Integration
Ozutemiz, K. B., Wissman, J., Ozdoganlar, O. B., & Majidi, C. (2018) · Advanced Materials Interfaces · doi:10.1002/admi.201701596 · Cited by 251
Self-citationIntrinsically Stretchable Biphasic (Solid–Liquid) Thin Metal Films
Hirsch, A., Michaud, H. O., Gerratt, A. P., de Mulatier, S., & Lacour, S. P. (2016) · Advanced Materials · doi:10.1002/adma.201506234 · Cited by 234
Yu, Y., Yan, C., & Zheng, Z. (2014) · Advanced Materials · doi:10.1002/adma.201305558 · Cited by 195
Liquid metal actuation by electrical control of interfacial tension
Eaker, C. B., & Dickey, M. D. (2016) · Applied Physics Reviews · doi:10.1063/1.4959898 · Cited by 183
Guo, R., Yu, Y., Xie, Z., Liu, X., Zhou, X., Gao, Y., Liu, Z., Zhou, F., Yang, Y., & Zheng, Z. (2013) · Advanced Materials · doi:10.1002/adma.201301184 · Cited by 181
Selectively plated stretchable liquid metal wires for transparent electronics
Li, G., Wu, X., & Lee, D.-W. (2015) · Sensors and Actuators B: Chemical · doi:10.1016/j.snb.2015.07.062 · Cited by 165
Printable stretchable interconnects
Dang, W., Vinciguerra, V., Lorenzelli, L., & Dahiya, R. (2017) · Flexible and Printed Electronics · doi:10.1088/2058-8585/aa5ab2 · Cited by 159
Field‐Controlled Electrical Switch with Liquid Metal
Wissman, J., Dickey, M. D., & Majidi, C. (2017) · Advanced Science · doi:10.1002/advs.201700169 · Cited by 151
Self-citationEffect of strain rate on the fracture behaviour of skin
Arumugam, V., Naresh, M. D., & Sanjeevi, R. (1994) · Journal of Biosciences · doi:10.1007/bf02716820 · Cited by 144
Yu, Y., Xiao, X., Zhang, Y., Li, K., Yan, C., Wei, X., Chen, L., Zhen, H., Zhou, H., Zhang, S., et al. (2016) · Advanced Materials · doi:10.1002/adma.201505119 · Cited by 88
Temporary-tattoo for long-term high fidelity biopotential recordings
Bareket, L., Inzelberg, L., Rand, D., David‐Pur, M., Rabinovich, D., Brandes, B., & Hanein, Y. (2016) · Scientific Reports · doi:10.1038/srep25727 · Cited by 88
Okamoto, M., Kurotobi, M., Takeoka, S., Sugano, J., Iwase, E., Iwata, H., & Fujie, T. (2017) · Journal of Materials Chemistry C · doi:10.1039/c6tc04469g · Cited by 19
Cited by
Zhang, L., Kumar, K. S., He, H., Cai, C. J., He, X., Gao, H., Yue, S., Li, C., Seet, R. C.-S., Ren, H., et al. (2020) · Nature Communications · doi:10.1038/s41467-020-18503-8 · Cited by 574
An electrically conductive silver–polyacrylamide–alginate hydrogel composite for soft electronics
Ohm, Y., Pan, C., Ford, M. J., Huang, X., Liao, J., & Majidi, C. (2021) · Nature Electronics · doi:10.1038/s41928-021-00545-5 · Cited by 546
Self-citationAttributes, Fabrication, and Applications of Gallium‐Based Liquid Metal Particles
Lin, Y., Genzer, J., & Dickey, M. D. (2020) · Advanced Science · doi:10.1002/advs.202000192 · Cited by 503
Huang, Q., & Zhu, Y. (2019) · Advanced Materials Technologies · doi:10.1002/admt.201800546 · Cited by 482
Highly stretchable multilayer electronic circuits using biphasic gallium-indium
Liu, S., Shah, D. S., & Kramer-Bottiglio, R. (2021) · Nature Materials · doi:10.1038/s41563-021-00921-8 · Cited by 409
Metadata
- Authors
- Tavakoli, M., Malakooti, M. H., Paisana, H., Ohm, Y., Green Marques, D., Alhais Lopes, P., Piedade, A. P., de Almeida, A. T., & Majidi, C.
- Venue
- Advanced Materials
- Publisher
- Wiley
- Published
- 2018-05-29
- Volume
- 30
- Issue
- 29
- Pages
- e1801852-e1801852
- ISSN
- 0935-9648 (ISSN-L)
- 1521-4095
- OpenAlex
- W2805639326
- Cited by
- 310
- References
- 23
- FWCI
- 12.14
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.