The DOI matches its Crossref record; 50 of the 50 references it cites were found in a registry or an index.
Understanding the Doping Effect on NiO: Toward High‐Performance Inverted Perovskite Solar Cells
Abstract
High‐quality hole transport layers are prepared by spin‐coating copper doped nickel oxide (Cu:NiO) nanoparticle inks at room temperature without further processing. In agreement with theoretical calculations predicting that Cu doping results in acceptor energy levels closer to the valence band maximum compared to gap states of nickel vacancies in undoped NiO, an increase in the conductivity in Cu:NiO films compared to NiO is observed. Cu in Cu:NiO can be found in both Cu+ and Cu 2+ states, and the substitution of Ni 2+ with Cu+ contributes to both increased carrier concentration and carrier mobility. In addition, the films exhibit increased work function, which together with the conductivity increase, enables improved charge transfer and extraction. Furthermore, recombination losses due to lower monomolecular Shockley‐Read‐Hall recombination are reduced. These factors result in an improvement of all photovoltaic performance parameters and consequently an increased efficiency of the inverted planar perovskite solar cells. A power conversion efficiency (PCE) exceeding 20% could be achieved for small‐area devices, while PCE values of 17.41 and 18.07% are obtained for flexible devices and large area (1 cm 2) devices on rigid substrates, respectively.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Solvent engineering for high-performance inorganic–organic hybrid perovskite solar cells
Jeon, N. J., Noh, J. H., Kim, Y. C., Yang, W. S., Ryu, S., & Seok, S. I. (2014) · Nature Materials · doi:10.1038/nmat4014 · Cited by 6,723
Iodide management in formamidinium-lead-halide–based perovskite layers for efficient solar cells
Yang, W. S., Park, B.-W., Jung, E. H., Jeon, N. J., Kim, Y. C., Lee, D. U., Shin, S. S., Seo, J., Kim, E. K., Noh, J. H., et al. (2017) · Science · doi:10.1126/science.aan2301 · Cited by 5,445
Efficient and stable solution-processed planar perovskite solar cells via contact passivation
Tan, H., Jain, A., Voznyy, O., Lan, X., García de Arquer, F. P., Fan, J. Z., Quintero-Bermudez, R., Yuan, M., Zhang, B., Zhao, Y., et al. (2017) · Science · doi:10.1126/science.aai9081 · Cited by 2,342
Self-citationEfficient and stable large-area perovskite solar cells with inorganic charge extraction layers
Chen, W., Wu, Y., Yue, Y., Liu, J., Zhang, W., Yang, X., Chen, H., Bi, E., Ashraful, I., Grätzel, M., et al. (2015) · Science · doi:10.1126/science.aad1015 · Cited by 2,279
Self-citationImproved air stability of perovskite solar cells via solution-processed metal oxide transport layers
You, J., Meng, L., Song, T.-B., Guo, T.-F., Yang, Y. (., Chang, W.-H., Hong, Z., Chen, H., Zhou, H., Chen, Q., et al. (2016) · Nature Nanotechnology · doi:10.1038/nnano.2015.230 · Cited by 2,123
Jiang, Q., Zhang, L., Wang, H., Yang, X., Meng, J., Liu, H., Yin, Z., Wu, J., Zhang, X., & You, J. (2016) · Nature Energy · doi:10.1038/nenergy.2016.177 · Cited by 2,024
Bi, C., Wang, Q., Shao, Y., Yuan, Y., Xiao, Z., & Huang, J. (2015) · Nature Communications · doi:10.1038/ncomms8747 · Cited by 1,660
The rapid evolution of highly efficient perovskite solar cells
Correa-Baena, J.-P., Abate, A., Saliba, M., Tress, W., Jesper Jacobsson, T., Grätzel, M., & Hagfeldt, A. (2017) · Energy & Environmental Science · doi:10.1039/c6ee03397k · Cited by 1,140
Kim, J. H., Liang, P., Williams, S. T., Cho, N., Chueh, C., Glaz, M. S., Ginger, D. S., & Jen, A. K. ‐. (2015) · Advanced Materials · doi:10.1002/adma.201404189 · Cited by 833
A solvent- and vacuum-free route to large-area perovskite films for efficient solar modules
Chen, H., Ye, F., Tang, W., He, J., Yin, M., Wang, Y., Xie, F., Bi, E., Yang, X., Grätzel, M., et al. (2017) · Nature · doi:10.1038/nature23877 · Cited by 716
Wu, Y., Yang, X., Chen, W., Yue, Y., Cai, M., Xie, F., Bi, E., Islam, A., & Han, L. (2016) · Nature Energy · doi:10.1038/nenergy.2016.148 · Cited by 644
Self-citationWu, Y., Xie, F., Chen, H., Yang, X., Su, H., Cai, M., Zhou, Z., Noda, T., & Han, L. (2017) · Advanced Materials · doi:10.1002/adma.201701073 · Cited by 634
Self-citationHigh efficiency flexible perovskite solar cells using superior low temperature TiO2
Yang, D., Yang, R., Zhang, J., Yang, Z., (Frank) Liu, S., & Li, C. (2015) · Energy & Environmental Science · doi:10.1039/c5ee02155c · Cited by 570
Zhang, H., Cheng, J., Lin, F., He, H., Mao, J., Wong, K. S., Jen, A. K.-Y., & Choy, W. C. H. (2016) · ACS Nano · doi:10.1021/acsnano.5b07043 · Cited by 560
Park, J. H., Seo, J., Park, S., Shin, S. S., Kim, Y. C., Jeon, N. J., Shin, H., Ahn, T. K., Noh, J. H., Yoon, S. C., et al. (2015) · Advanced Materials · doi:10.1002/adma.201500523 · Cited by 550
Zhang, Z., & Wang, P. (2012) · J. Mater. Chem. · doi:10.1039/c1jm14478b · Cited by 498
Control of I–V Hysteresis in CH3NH3PbI3 Perovskite Solar Cell
Kim, H.-S., Jang, I.-H., Ahn, N., Choi, M., Guerrero, A., Bisquert, J., & Park, N.-G. (2015) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.5b02273 · Cited by 478
Highly Efficient Flexible Perovskite Solar Cells Using Solution-Derived NiOx Hole Contacts
Yin, X., Chen, P., Que, M., Xing, Y., Que, W., Niu, C., & Shao, J. (2016) · ACS Nano · doi:10.1021/acsnano.5b08135 · Cited by 476
Beyond Efficiency: the Challenge of Stability in Mesoscopic Perovskite Solar Cells
Rong, Y., Liu, L., Mei, A., Li, X., & Han, H. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201501066 · Cited by 473
Jung, J. W., Chueh, C., & Jen, A. K. ‐. (2015) · Advanced Materials · doi:10.1002/adma.201503298 · Cited by 458
Zhu, Z., Bai, Y., Zhang, T., Liu, Z., Long, X., Wei, Z., Wang, Z., Zhang, L., Wang, J., Yan, F., et al. (2014) · Angewandte Chemie International Edition · doi:10.1002/anie.201405176 · Cited by 457
Cesium Doped NiOx as an Efficient Hole Extraction Layer for Inverted Planar Perovskite Solar Cells
Chen, W., Liu, F., Feng, X., Djurišić, A. B., Chan, W. K., & He, Z. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201700722 · Cited by 457
Self-citationp-type Mesoscopic Nickel Oxide/Organometallic Perovskite Heterojunction Solar Cells
Wang, K.-C., Jeng, J.-Y., Shen, P.-S., Chang, Y.-C., Diau, E. W.-G., Tsai, C.-H., Chao, T.-Y., Hsu, H.-C., Lin, P.-Y., Chen, P., et al. (2014) · Scientific Reports · doi:10.1038/srep04756 · Cited by 444
Yang, D., Yang, R., Ren, X., Zhu, X., Yang, Z., Li, C., & Liu, S. (. (2016) · Advanced Materials · doi:10.1002/adma.201600446 · Cited by 438
Atomic and Ionic Radii of Elements 1–96
Rahm, M., Hoffmann, R., & Ashcroft, N. W. (2016) · Chemistry – A European Journal · doi:10.1002/chem.201602949 · Cited by 428
Seo, S., Park, I. J., Kim, M., Lee, S., Bae, C., Jung, H. S., Park, N.-G., Kim, J. Y., & Shin, H. (2016) · Nanoscale · doi:10.1039/c6nr01601d · Cited by 380
Wang, K.-C., Shen, P.-S., Li, M.-H., Chen, S., Lin, M.-W., Chen, P., & Guo, T.-F. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am503610u · Cited by 358
Bai, Y., Chen, H., Xiao, S., Xue, Q., Zhang, T., Zhu, Z., Li, Q., Hu, C., Yang, Y., Hu, Z., et al. (2016) · Advanced Functional Materials · doi:10.1002/adfm.201505215 · Cited by 351
Highly Efficient Flexible Perovskite Solar Cells UsingSolution-Derived NiOx Hole Contacts
Yin, X., Chen, P., Meidan, Q., Yonglei, X., Que, W., Chunming, N., & Shao, J. (2016) · INDIGO (University of Illinois at Chicago) · doi:10.1021/acsnano.5b08135.s001 · Cited by 340
Sequential Deposition of CH3NH3PbI3 on Planar NiO Film for Efficient Planar Perovskite Solar Cells
Hu, L., Peng, J., Wang, W., Xia, Z., Yuan, J., Lu, J., Huang, X., Ma, W., Song, H., Chen, W., et al. (2014) · ACS Photonics · doi:10.1021/ph5000067 · Cited by 259
Self-citationXue, Q., Bai, Y., Liu, M., Xia, R., Hu, Z., Chen, Z., Jiang, X., Huang, F., Yang, S., Matsuo, Y., et al. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201602333 · Cited by 243
A large area (70 cm2) monolithic perovskite solar module with a high efficiency and stability
Priyadarshi, A., Haur, L. J., Murray, P., Fu, D., Kulkarni, S., Xing, G., Sum, T. C., Mathews, N., & Mhaisalkar, S. G. (2016) · Energy & Environmental Science · doi:10.1039/c6ee02693a · Cited by 241
CH3NH3PbI3-Based Planar Solar Cells with Magnetron-Sputtered Nickel Oxide
Cui, J., Meng, F., Zhang, H., Cao, K., Yuan, H., Cheng, Y., Huang, F., & Wang, M. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am507108u · Cited by 231
Nickel oxide nanoparticles for efficient hole transport in p-i-n and n-i-p perovskite solar cells
Liu, Z., Zhu, A., Cai, F., Tao, L., Zhou, Y., Zhao, Z., Chen, Q., Cheng, Y.-B., & Zhou, H. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta01593c · Cited by 228
Zhang, H., Cheng, J., Li, D., Lin, F., Mao, J., Liang, C., Jen, A. K. ‐., Grätzel, M., & Choy, W. C. H. (2017) · Advanced Materials · doi:10.1002/adma.201604695 · Cited by 225
Black Phosphorus Quantum Dots for Hole Extraction of Typical Planar Hybrid Perovskite Solar Cells
Chen, W., Li, K., Wang, Y., Feng, X., Liao, Z., Su, Q., Lin, X., & He, Z. (2017) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.6b02843 · Cited by 224
Self-citationEfficient Flexible Solar Cell based on Composition‐Tailored Hybrid Perovskite
Bi, C., Chen, B., Wei, H., DeLuca, S. J., & Huang, J. (2017) · Advanced Materials · doi:10.1002/adma.201605900 · Cited by 220
Kwon, U., Kim, B.-G., Nguyen, D. C., Park, J.-H., Ha, N. Y., Kim, S.-J., Ko, S. H., Lee, S., Lee, D., & Park, H. J. (2016) · Scientific Reports · doi:10.1038/srep30759 · Cited by 219
Chen, W., Xu, L., Feng, X., Jie, J., & He, Z. (2017) · Advanced Materials · doi:10.1002/adma.201603923 · Cited by 215
Self-citationOvercoming the Interface Losses in Planar Heterojunction Perovskite‐Based Solar Cells
Hou, Y., Chen, W., Baran, D., Stubhan, T., Luechinger, N. A., Hartmeier, B., Richter, M., Min, J., Chen, S., Quiroz, C. O. R., et al. (2016) · Advanced Materials · doi:10.1002/adma.201504168 · Cited by 206
Self-citationYe, F., Chen, H., Xie, F., Tang, W., Yin, M., He, J., Bi, E., Wang, Y., Yang, X., & Han, L. (2016) · Energy & Environmental Science · doi:10.1039/c6ee01411a · Cited by 206
He, Q., Yao, K., Wang, X., Xia, X., Leng, S., & Li, F. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b13621 · Cited by 198
Achieving Large‐Area Planar Perovskite Solar Cells by Introducing an Interfacial Compatibilizer
Lee, J., Kang, H., Kim, G., Back, H., Kim, J., Hong, S., Park, B., Lee, E., & Lee, K. (2017) · Advanced Materials · doi:10.1002/adma.201606363 · Cited by 190
Perovskite solar cells - An overview of critical issues
Djurišić, A. B., Liu, F. Z., Tam, H. W., Wong, M. K., Ng, A., Surya, C., Chen, W., & He, Z. B. (2017) · Progress in Quantum Electronics · doi:10.1016/j.pquantelec.2017.05.002 · Cited by 182
Self-citationIdentifying Fundamental Limitations in Halide Perovskite Solar Cells
Leong, W. L., Ooi, Z., Sabba, D., Yi, C., Zakeeruddin, S. M., Grätzel, M., Gordon, J. M., Katz, E. A., & Mathews, N. (2016) · Advanced Materials · doi:10.1002/adma.201505480 · Cited by 156
Natu, G., Hasin, P., Huang, Z., Ji, Z., He, M., & Wu, Y. (2012) · ACS Applied Materials & Interfaces · doi:10.1021/am301565j · Cited by 150
Self-citationHuang, A., Zhu, J., Zheng, J., et al. (2016) · Journal of Materials Chemistry C · doi:10.1039/c6tc03624d · Cited by 117
Corani, A., Li, M.-H., Shen, P., Chen, P., Guo, T., Nahhas, A. E., Zheng, K., Yartsev, A. P., Sundström, V., & Ponseca, C. S. (2016) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.6b00238 · Cited by 115
Estimation of the van der Waals radii of the d-block elements using the concept of bond valence
Nag, S., Banerjee, K., & Datta, D. (2007) · New Journal of Chemistry · doi:10.1039/b701197k · Cited by 98
Chen, W., Luo, S., Wan, Z., Feng, X., Liu, X., & He, Z. (2017) · Optics Express · doi:10.1364/oe.25.00a253 · Cited by 18
Self-citation
Cited by
Defect and Contact Passivation for Perovskite Solar Cells
Aydin, E., De Bastiani, M., & De Wolf, S. (2019) · Advanced Materials · doi:10.1002/adma.201900428 · Cited by 681
Perovskite Tandem Solar Cells: From Fundamentals to Commercial Deployment
Li, H., & Zhang, W. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00780 · Cited by 524
Stability of perovskite solar cells: issues and prospects
Chowdhury, T. A., Bin Zafar, M. A., Sajjad-Ul Islam, M., Shahinuzzaman, M., Islam, M. A., & Khandaker, M. U. (2023) · RSC Advances · doi:10.1039/d2ra05903g · Cited by 444
Yin, X., Song, Z., Li, Z., & Tang, W. (2020) · Energy & Environmental Science · doi:10.1039/d0ee02337j · Cited by 388
New Strategies for Defect Passivation in High‐Efficiency Perovskite Solar Cells
Akin, S., Arora, N., Zakeeruddin, S. M., Grätzel, M., Friend, R. H., & Dar, M. I. (2020) · Advanced Energy Materials · doi:10.1002/aenm.201903090 · Cited by 352
Metadata
- Authors
- Chen, W., Wu, Y., Fan, J., Djurišić, A. B., Liu, F., Tam, H. W., Ng, A., Surya, C., Chan, W. K., Wang, D., & He, Z.
- Venue
- Advanced Energy Materials
- Publisher
- Wiley
- Published
- 2018-03-25
- Volume
- 8
- Issue
- 19
- ISSN
- 1614-6832 (ISSN-L)
- 1614-6840
- OpenAlex
- W2790131787
- Cited by
- 435
- References
- 50
- FWCI
- 17.97
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.