The DOI matches its Crossref record; 67 of the 81 references it cites were found in a registry or an index; 10 of the 21 sources its claims cite were checked for support.
3D Printing of Graphene Aerogel Microspheres to Architect High‐Performance Electrodes for Hydrogen Evolution Reaction
Abstract
AbstractThe hydrogen evolution reaction (HER) efficiency is highly dependent on the electrocatalysts microstructure and the macrostructure of the electrodes. Herein, the graphene aerogel microspheres loaded with well‐dispersed ultrafine Ni/Co nanoparticles catalyst is prepared through electro‐spraying, in‐situ crosslinking, freeze‐drying, and pyrolysis, and then is utilized to print the HER electrode via direct ink writing (DIW). The obtained graphene‐based aerogel microspheres possess peculiar cabbage‐like mesoporous structures which allow ready access of reaction species to active sites, optimal mass transfer, and proton diffusion within the microspheres. DIW 3D printing achieves the ordered control on the periodic lattice macro‐geometry and thus facilitates the fast gas bubble evolution and release from the electrode surface. The as‐fabricated 3D electrode possesses a low overpotential of 341 mV at 10 mA cm−2, a decrease by 31.5% compared to 3D printed electrode directly from 2D graphene, and a low Tafel slope of 119.1 mV dec−1, 40% lower than that of the electrodes fabricated via directly casting the aerogel microspheres. Furthermore, the 3D‐printed electrode of aerogel microspheres displays good HER stability. This work provides a good approach for constructing high‐performance HER electrodes through 3D printing of graphene aerogel microspheres.
Overview
CoChat Summary
TL;DR
The authors prepare reduced graphene oxide aerogel microspheres (rGOAMs) loaded with ultrafine Ni/Co nanoparticles and use them as a direct-ink-writing (DIW) ink to 3D-print lattice-structured hydrogen evolution reaction (HER) electrodes. The printed electrode reaches a low overpotential of ≈341 mV at 10 mA cm⁻² and a Tafel slope of 119.1 mV dec⁻¹, which the authors attribute to the microspheres' mesoporous structure plus the printed periodic macropores that speed bubble release.
Key findings
- The optimized catalyst composition was rGOAMs-2Ni1Co (Ni:Co = 2:1), which gave η₁₀ ≈ 338.3 mV and the lowest Tafel slope (≈88.8 mV dec⁻¹) among the five Ni/Co ratios tested, and the highest Ni⁰:Ni(II) ratio (≈0.659).
- Raising the thermal reduction temperature improved performance: η₁₀ fell from 404.1 mV (300 °C) to 365.4 mV (600 °C) to 338.3 mV (800 °C); the 800 °C sample had the highest ECSA (≈101.04 cm²), and no Ni/Co metal reduction occurred at 300 °C.
- The DIW-printed electrode (3DP rGOAMs-2Ni1Co) achieved η₁₀ ≈ 341 mV, a 31.5% decrease versus a 3D-printed electrode made directly from 2D graphene (498 mV for the Ni/Co-free 3DP rGO reference), and a Tafel slope of 119.1 mV dec⁻¹, ~40% lower than the directly cast rGOAMs-2Ni1Co electrode (197.1 mV dec⁻¹).
- Stability: the printed electrode's HER behavior was nearly unchanged after 1000 CV cycles and its current was nearly unchanged over more than 24 h at ≈10 mA cm⁻²; charge-transfer resistance was below 1 Ω for both cast and printed rGOAMs electrodes. Bubble release was even and fast (within 80 s) for the printed electrode versus localized emission for the cast one.
Methods
- Fabrication: GO/sodium alginate microdroplets were electrosprayed into a two-phase collector (hexane over Ni²⁺/Co²⁺ acetate solution) for in-situ crosslinking, then freeze-dried and pyrolyzed; microspheres were ≈500 μm with cabbage-like mesoporous structure, and Ni/Co nanoparticles were ≈18.2 nm (Scherrer) / ≈16 nm mean (TEM, range 10–60 nm).
- Ink/printing: 250 mg GOAMs-2Ni1Co plus 300 mg carboxylated cellulose nanocrystals (C-CNC) in 5 mL water; printed on a Regenovo Bio-Printer-WS through an 800 μm nozzle at 0.05 MPa N₂, 1 cm × 1 cm, five layers, 0.4 mm layer thickness, 2 mm filament spacing, then carbonized at 800 °C for 2 h in Ar.
- Electrochemistry: standard three-electrode cell in N₂-saturated 1.0 M KOH, Ag/AgCl reference, graphite counter electrode, LSV at 5 mV s⁻¹, 1000 CV cycles at 100 mV s⁻¹ for stability, EIS from 100 kHz to 0.1 Hz, and chronopotentiometry at 10 mA cm⁻²; characterization by XRD, XPS, SEM, TEM, Raman, ICP-MS, and rheology (Herschel–Bulkley fitting).
Limitations
- The paper states that its benchmarking against literature HER electrodes based on carbon carriers with Ni or Co nanoparticles "is a relative comparison in a limited investigated range."
- The paper reports no explicit limitations section beyond that; evident from the text: performance is demonstrated only in alkaline (1.0 M KOH) electrolyte, the long-term stability test covers only ~24 h, and the comparison to Pt-based catalysts is qualitative (Pt/C used as a reference but no comparative η₁₀/Tafel values are given in the text).
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
5 Valid · 2 Not valid · 0 Not checked · 69 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“inevitable oxidization happens on the surface of Ni metal nanoparticles, which are existed in the form of Ni(II), that is, NiO.[51–55]”
§ 2. Results and Discussions > 2.2. HER Performance of the Aerogel Microspheres
What the sources say
- Not checked — no full text of the sourcecites [51] source
- Not checked — no full text of the sourcecites [52] source
- Not checked — no full text of the sourcecites [53] source
- Not checked — no full text of the sourcecites [54] source
- Partly supportedcites [55] sourceExperimental — accuracy not yet measured
The Results and discussion section reports Ni²⁺ signals consistent with NiO and attributes the absence of a metallic-Ni surface signal to NiO formation on metallic Ni. It also says this composite was deliberately oxidized in air; it does not establish that surface oxidation is inevitable for Ni nanoparticles generally. No page number is available in our copy. (LLM, conf=0.86)
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The reduced graphene oxide aerogel microspheres (rGOAMs) with ordered microchannel structures has been recently proven as a stable template to host various electroactive catalysts by our group.[21–26]”
What the sources say
- Not checked — no full text of the sourcecites [21] source
- Not checked — no full text of the sourcecites [22] source
- Not checked — no full text of the sourcecites [23] source
- Partly supportedcites [24] sourceExperimental — accuracy not yet measured
The Introduction (around p. 3100) reports incorporating TMDC nanosheets into rGOAMs and describes the present MXene/rGOAM material as retaining ordered microchannels. The Conclusions (p. 3106) report improved hydrogen-evolution performance for the MXene composite. These passages support rGOAMs as a host for electroactive materials, but this paper does not establish that they are a stable template for various catalysts generally. (LLM, conf=0.84)
- Partly supportedcites [25] sourceExperimental — accuracy not yet measured
The Introduction describes GO aerogel microspheres with a center-diverging microchannel structure used to disperse catalytic nanosheets. The Results and Discussion reports high stability for the Ni–MoS₂/prGOAM electrodes under HER conditions. This paper supports their use as a catalyst scaffold, but tests MoS₂ and Ni-promoted MoS₂ rather than establishing stability as a template for various electroactive catalysts. (LLM, conf=0.84)
- Supportedcites [26] source
The Introduction describes microspheres with centrally diverging microchannels and reports incorporating MoSe2, MoS2, WS2 and WSe2 into their graphene network without altering that morphology. The Results and Discussion (§3.1) reports that annealing stabilized the catalyst-bearing microspheres and preserved their structure. (LLM, conf=0.89)
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“a decrease by 31.5% compared to 3D printed electrode directly from 2D graphene”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The paper states this without a source or data behind it here, so there is nothing to check it against. The quote shows it is in the paper.
In the paper
“DIW 3D printing achieves the ordered control on the periodic lattice macro-geometry”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: unclear — It is unclear why the paper says it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the 3D-printed electrode of aerogel microspheres displays good HER stability”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
43 more claims
Create a free account to see all 76 claims and every source verdict.
- Probably not a substantial claim. 4
- It may state two separate claims as one. 22
- The quote only partly states this claim. 4
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 2. Results and Discussions > 2.2. HER Performance of the Aerogel Microspheres
“lating the ECSA via Equation (1)”
§ 2. Results and Discussions > 2.2. HER Performance of the Aerogel Microspheres
“ECSA = CDL Cs (2)”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 2. Results and Discussions > 2.2. HER Performance of the Aerogel Microspheres
“Peaks of Co° can be observed in all five samples”
§ 4. Experimental Section
“the rGOAMs-xNiyCo were obtained by thermal reduction in Ar atmosphere from GOAM- xNiyCo gained above and denoted as rGOAMs-2Ni0Co, rGOAMs- 2Ni1Co, rGOAMs-2Ni2Co, rGOAMs-1Ni2Co and rGOAMs-0Ni2Co respectively.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 2. Results and Discussions > 2.3. DIW 3D Printed Electrode of rGOAMs-2Ni1Co for HER
“the content of Co and Ni in the 3D-printed electrode before calcination, are 1.7553 wt% and 0.8730 wt%, respectively”
§ 2. Results and Discussions > 2.3. DIW 3D Printed Electrode of rGOAMs-2Ni1Co for HER
“after calcination, they increase to 6.52% (Ni) and 3.33% (Co) respectively”
Citations
Cites
Benchmarking Heterogeneous Electrocatalysts for the Oxygen Evolution Reaction
McCrory, C. C. L., Jung, S., Peters, J. C., & Jaramillo, T. F. (2013) · Journal of the American Chemical Society · doi:10.1021/ja407115p · Cited by 7,026
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
2D Transition Metal Dichalcogenides: Design, Modulation, and Challenges in Electrocatalysis
Fu, Q., Han, J., Wang, X., Xu, P., Yao, T., Zhong, J., Zhong, W., Liu, S., Gao, T., Zhang, Z., et al. (2021) · Advanced Materials · doi:10.1002/adma.201907818 · Cited by 697
Recent Advances in Oxidation Stable Chemistry of 2D MXenes
Cao, F., Zhang, Y., Wang, H., Khan, K., Tareen, A. K., Qian, W., Zhang, H., & Ågren, H. (2022) · Advanced Materials · doi:10.1002/adma.202107554 · Cited by 648
Huang, H., Yan, M., Yang, C., He, H., Jiang, Q., Yang, L., Lu, Z., Sun, Z., Xu, X., Bando, Y., et al. (2019) · Advanced Materials · doi:10.1002/adma.201903415 · Cited by 454
Rational Design of Graphene‐Supported Single Atom Catalysts for Hydrogen Evolution Reaction
Hossain, M. D., Liu, Z., Zhuang, M., Yan, X., Xu, G., Gadre, C. A., Tyagi, A., Abidi, I. H., Sun, C., Wong, H., et al. (2019) · Advanced Energy Materials · doi:10.1002/aenm.201803689 · Cited by 434
3D Printing for Electrochemical Energy Applications
Browne, M. P., Redondo, E., & Pumera, M. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00783 · Cited by 434
Liu, W., Wang, X., Wang, F., Du, K., Zhang, Z., Guo, Y., Yin, H., & Wang, D. (2021) · Nature Communications · doi:10.1038/s41467-021-27118-6 · Cited by 352
Benson, E. E., Zhang, H., Schuman, S. A., Nanayakkara, S. U., Bronstein, N. D., Ferrere, S., Blackburn, J. L., & Miller, E. M. (2018) · Journal of the American Chemical Society · doi:10.1021/jacs.7b11242 · Cited by 303
3D Graphene‐Based H2‐Production Photocatalyst and Electrocatalyst
Kuang, P., Sayed, M., Fan, J., Cheng, B., & Yu, J. (2020) · Advanced Energy Materials · doi:10.1002/aenm.201903802 · Cited by 302
Research works printed but not linked: 2
- Zeng T. B., 2023, Adv. Sci., 10
- 10.1186/s40580-023-00354-w · DOI · Paper page
Cited by
An emerging 2D borophene nanomaterial: Synthesis, properties and hydrogen energy applications
Yang, F., & Pan, Y. (2025) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2025.217015 · Cited by 79
Zhang, H., Xu, H., Huang, C., Zhu, H., & Li, G. (2025) · Inorganic Chemistry · doi:10.1021/acs.inorgchem.4c05056 · Cited by 45
Advances in Ice-Templated Graphene Aerogels: Fabrication, Properties, and Applications
Li, M., Zheng, Y., Bai, H., & Gao, W. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c01179 · Cited by 34
Wang, Y., Pang, N., Yin, X., Yu, M., Wang, C., & Zhou, C. (2025) · Small · doi:10.1002/smll.202411460 · Cited by 28
(2026) · doi:10.1007/s40820-026-02109-8 · Cited by 15
Self-citation
Metadata
- Authors
- Cheng, Y., Wang, Z., Lavorgna, M., He, L., & Xia, H.
- Affiliations
- Sichuan University (CN)
- National Research Council (IT)
- Corresponding author
- He, Lirong
- Xia, Hesheng
- Venue
- Small
- Publisher
- Wiley
- Published
- 2024-12-08
- Volume
- 21
- Issue
- 4
- ISSN
- 1613-6810 (ISSN-L)
- 1613-6829
- OpenAlex
- W4405200952
- Semantic Scholar
- 004a32b8ba1bfa8942a7a34f7900e8d16d3b993d
- Cited by
- 20
- References
- 81
- Citations by year
- 2026: 14 · 2025: 6
- FWCI
- 1.33
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Small (publishedVersion)
- PubMed (publishedVersion)
- Funders
- National Key Research and Development Program of China (2023YFE0105600)
- Topics
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Supercapacitor Materials and Fabrication
- Keywords
- hydrogen evolution reaction, 3D printing, direct ink writing, electrocatalysts, electrode microstructure, gas bubble evolution, proton diffusion, Tafel slope
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: 3D Printing of Graphene Aerogel Microspheres to Architect High‐Performance Electrodes for Hydrogen Evolution Reaction. https://app.cochat.ai/papers/10.1002/smll.202408869
- The paper
- Cheng, Y., Wang, Z., Lavorgna, M., He, L., & Xia, H. (2025). 3D Printing of Graphene Aerogel Microspheres to Architect High‐Performance Electrodes for Hydrogen Evolution Reaction. Small. https://doi.org/10.1002/smll.202408869
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.