The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
An End‐to‐End Steel Strip Surface Defects Recognition System Based on Convolutional Neural Networks
Abstract
Steel strip surface defects recognition is very important to steel strip production and quality control, which needs further improvement. In this paper, an end‐to‐end surface defects recognition system is proposed for steel strip surface inspection. This system is based on the symmetric surround saliency map for surface defects detection and deep convolutional neural networks (CNNs) which directly use the defect image as input and defect category as output for seven classes of steel strip defects classification. The CNNs are trained purely on raw defect images and learned defect features from the training of network, which avoiding the separation between feature extraction and image classification, so that forms an end‐to‐end defects recognition pipeline. To further illustrate the superiority of the defect recognition methods with CNNs, an authoritative and standard steel strip surface defect dataset − NEU is also used to evaluate the defect recognition effect using CNNs. Experimental results demonstrate that the proposed methods perform well in steel strip surface defect detection of different types and achieve a high recognition rate for defect images. In addition, a series of data augmentation methods are discussed to analyze its effect on avoiding over‐fitting for defects recognition.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Yi.L., Li.G., Jiang M. [31] 114x114 1.3 ms 99% 7”
From Real-time system for automatic cold strip surface defect detection (2019) · cites this paper as [31]
In the citing paper
“their model gets a better accuracy at 99.05%.”
From A Compact Convolutional Neural Network for Surface Defect Inspection (2020) · cites this paper as [2]
In the citing paper
“Their work proves that data augmentation on this dataset is crucial for performance improvement”
From A Compact Convolutional Neural Network for Surface Defect Inspection (2020) · cites this paper as [2]
Citations
Cites
(2014) · Cited by 33,419
Learning Internal Representations by Error Propagation
Rumelhart, D. E., Hinton, G. E., & Williams, R. J. (1985) · doi:10.21236/ada164453 · Cited by 16,172
CNN Features Off-the-Shelf: An Astounding Baseline for Recognition
Razavian, A. S., Azizpour, H., Sullivan, J., & Carlsson, S. (2014) · 2014 IEEE Conference on Computer Vision and Pattern Recognition Workshops · doi:10.1109/cvprw.2014.131 · Cited by 4,451
Frequency-tuned salient region detection
Achanta, R., Hemami, S., Estrada, F., & Susstrunk, S. (2009) · 2009 IEEE Conference on Computer Vision and Pattern Recognition · doi:10.1109/cvpr.2009.5206596 · Cited by 4,167
Practical Recommendations for Gradient-Based Training of Deep Architectures
Bengio, Y. (2012) · Lecture Notes in Computer Science · doi:10.1007/978-3-642-35289-8_26 · Cited by 2,259
Song, K., & Yan, Y. (2013) · Applied Surface Science · doi:10.1016/j.apsusc.2013.09.002 · Cited by 1,026
Saliency detection using maximum symmetric surround
Achanta, R., & Susstrunk, S. (2010) · 2010 IEEE International Conference on Image Processing · doi:10.1109/icip.2010.5652636 · Cited by 384
Steel defect classification with Max-Pooling Convolutional Neural Networks
Masci, J., Meier, U., Ciresan, D., Schmidhuber, J., & Fricout, G. (2012) · The 2012 International Joint Conference on Neural Networks (IJCNN) · doi:10.1109/ijcnn.2012.6252468 · Cited by 345
Review of vision-based steel surface inspection systems
Neogi, N., Mohanta, D. K., & Dutta, P. K. (2014) · EURASIP Journal on Image and Video Processing · doi:10.1186/1687-5281-2014-50 · Cited by 322
An intelligent real-time vision system for surface defect detection
Jia, H., Murphey, Y. L., Shi, J., & Chang, T.-S. (2004) · Proceedings of the 17th International Conference on Pattern Recognition, 2004. ICPR 2004. · doi:10.1109/icpr.2004.1334512 · Cited by 174
Research works printed but not linked: 5
- Xu X. R., 2010, Jisuanji Yingyong/J. Comput. Appl, 30, 2247
- Krizhevsky A., 2012, Adv. Neural Inf. Process. Syst, 25, 2012
- Song K., 2013, Math. Prob. Eng, 2013, 1
- Ciresan D., 2012, Eprint Arxiv, 157, 3642
- Srivastava N., 2014, J. Mach. Learn. Res, 15, 1929
Cited by
An End-to-End Steel Surface Defect Detection Approach via Fusing Multiple Hierarchical Features
He, Y., Song, K., Meng, Q., & Yan, Y. (2020) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2019.2915404 · Cited by 1,341
“However, most methods can only perform defect classification due to the lack of special data sets [18]–[21].”
BackgroundMethodYang, J., Li, S., Wang, Z., Dong, H., Wang, J., & Tang, S. (2020) · Materials · doi:10.3390/ma13245755 · Cited by 488
A deep-learning-based approach for fast and robust steel surface defects classification
Fu, G., Sun, P., Zhu, W., Yang, J., Cao, Y., Yang, M. Y., & Cao, Y. (2019) · Optics and Lasers in Engineering · doi:10.1016/j.optlaseng.2019.05.005 · Cited by 271
Review of surface defect detection of steel products based on machine vision
Tang, B., Chen, L., Sun, W., & Lin, Z. (2023) · IET Image Processing · doi:10.1049/ipr2.12647 · Cited by 271
Automated defect inspection system for metal surfaces based on deep learning and data augmentation
Yun, J. P., Shin, W. C., Koo, G., Kim, M. S., Lee, C., & Lee, S. J. (2020) · Journal of Manufacturing Systems · doi:10.1016/j.jmsy.2020.03.009 · Cited by 268
Khanam, R., Hussain, M., Hill, R., & Allen, P. (2024) · IEEE Access · doi:10.1109/access.2024.3425166 · Cited by 237
“In response to this critical need, Yi et al. [309] proposed an end-to-end system for surface defect recognition in steel strips.”
BackgroundYang, J., Fu, G., Zhu, W., Cao, Y., Cao, Y., & Yang, M. Y. (2020) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2020.2986875 · Cited by 189
“In our experiments, we consider the ETE CNN model proposed by Li et al. [24], the Decaf model-based approach (DECAF + MLR) proposed by Ren et al. [25], and the SqueezeNet-based model proposed by Fu et al. [27].”
BackgroundMethodResultInfluentialGeneralized Completed Local Binary Patterns for Time-Efficient Steel Surface Defect Classification
Luo, Q., Sun, Y., Li, P., Simpson, O., Tian, L., & He, Y. (2019) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2018.2852918 · Cited by 178
“Various algorithms such as multi-scale geometric analysis [10], Bayes theorem [11], support vector machine [12], the aforementioned VVRKFA [6], and the latest CNN [13] can be used for feature extraction and matching.”
MethodHe, Y., Song, K., Dong, H., & Yan, Y. (2019) · Optics and Lasers in Engineering · doi:10.1016/j.optlaseng.2019.06.020 · Cited by 171
Metal Additive Manufacturing Parts Inspection Using Convolutional Neural Network
Cui, W., Zhang, Y., Zhang, X., Li, L., & Liou, F. (2020) · Applied Sciences · doi:10.3390/app10020545 · Cited by 124
Steel Surface Defect Classification Using Deep Residual Neural Network
Konovalenko, I., Maruschak, P., Brezinová, J., Viňáš, J., & Brezina, J. (2020) · Metals · doi:10.3390/met10060846 · Cited by 118
Research Progress of Visual Inspection Technology of Steel Products—A Review
Sun, X., Gu, J., Tang, S., & Li, J. (2018) · Applied Sciences · doi:10.3390/app8112195 · Cited by 109
“Convolutional neural networks (CNNs) structure for surface defect recognition model (reproduced from Yi [40]).”
BackgroundMethodSMD LED chips defect detection using a YOLOv3-dense model
Chen, S., & Tsai, C.-C. (2021) · Advanced Engineering Informatics · doi:10.1016/j.aei.2021.101255 · Cited by 110
Cohn, R., & Holm, E. A. (2021) · Integrating materials and manufacturing innovation · doi:10.1007/s40192-021-00205-8 · Cited by 123
Chu, M., Gong, R., Gao, S., & Zhao, J. (2017) · Chemometrics and Intelligent Laboratory Systems · doi:10.1016/j.chemolab.2017.10.020 · Cited by 97
A rapid recognition method for electronic components based on the improved yolo-v3 network
Huang, R., Gu, J., Sun, X., Hou, Y., & Uddin, S. (2019) · Electronics · doi:10.3390/electronics8080825 · Cited by 94
A ResNet50-Based Method for Classifying Surface Defects in Hot-Rolled Strip Steel
Feng, X., Gao, X., & Luo, L. (2021) · Mathematics · doi:10.3390/math9192359 · Cited by 99
“[18] proposed an end-to-end surface defect”
A Compact Convolutional Neural Network for Surface Defect Inspection
Huang, Y., Qiu, C., Wang, X., Wang, S., & Yuan, K. (2020) · Sensors · doi:10.3390/s20071974 · Cited by 85
“Reference [2] introduces an end-to-end CNN for this surface defect classification task.”
BackgroundSurface Defect Detection Using Image Pyramid
Xiao, L., Wu, B., & Hu, Y. (2020) · IEEE Sensors Journal · doi:10.1109/jsen.2020.2977366 · Cited by 84
Gao, Y., Lin, J., Xie, J., & Ning, Z. (2021) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2020.3013277 · Cited by 82
“With high-level semantic features, the deep learning based methods [11], [12] are able to get higher accuracies.”
BackgroundSteel Surface Defect Detection Algorithm Based on YOLOv8
Song, X., Cao, S., Zhang, J., & Hou, Z. (2024) · Electronics · doi:10.3390/electronics13050988 · Cited by 93
“Yi et al. [20] proposed a method combining symmetrical surround saliency maps with CNN. Symmetrical surround saliency maps segment defect areas, followed by deep CNN for defect recognition.”
MethodGuan, S., Lei, M., & Lü, H. (2020) · IEEE Access · doi:10.1109/access.2020.2979755 · Cited by 88
“It could be widely used in various domains [21]–[23].”
BackgroundTLU-Net: A Deep Learning Approach for Automatic Steel Surface Defect Detection
Damacharla, P., V., A. R. M., Ringenberg, J., & Javaid, A. Y. (2021) · International Conference on Applied Artificial Intelligence (ICAPAI) · doi:10.1109/icapai49758.2021.9462060 · Cited by 101
“The CNN is used extensively for a different kind of defect classification on different data sets [9, 10].”
MethodÜzen, H., Türkoğlu, M., Yanikoglu, B. A., & Hanbay, D. (2022) · Expert Systems with Applications · doi:10.1016/j.eswa.2022.118269 · Cited by 80
Surface Defects Recognition of Wheel Hub Based on Improved Faster R-CNN
Sun, X., Gu, J., Huang, R., Zou, R., & Girón-Palomares, B. (2019) · Electronics · doi:10.3390/electronics8050481 · Cited by 79
Steel Surface Defect Diagnostics Using Deep Convolutional Neural Network and Class Activation Map
Lee, S. Y., Tama, B. A., Moon, S. J., & Lee, S. (2019) · Applied Sciences · doi:10.3390/app9245449 · Cited by 90
“Other approaches such as [12,17] have utilized CNN as the way of end-to-end learning framework.”
MethodFDD: a deep learning–based steel defect detectors
Akhyar, F., Liu, Y., Hsu, C.-Y., Shih, T. K., & Lin, C. (2023) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-023-11087-9 · Cited by 82
“Classification-based defect inspection systems [13–21] categorize an input image as defect or non-defect and calculate the class probability using stacks of convolutional neural networks.”
MethodA Real-Time Steel Surface Defect Detection Approach With High Accuracy
Wang, W., Mi, C., Wu, Z., Lu, K., Long, H., Pan, B., Li, D., Zhang, J., Chen, P., & Wang, B. (2021) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2021.3127648 · Cited by 77
“In recent years, the deep-learning-based methods have made many breakthroughs in the classification of surface defects of hot rolled steel strip [10]–[12].”
BackgroundDeep learning discrimination of quartz and resin in optical microscopy images of minerals
Iglesias, J. C. Á., Santos, R. B. M., & Paciornik, S. (2019) · Minerals Engineering · doi:10.1016/j.mineng.2019.04.032 · Cited by 65
Qing-sheng, J., Tan, D., Li, Y., Ji, S., Cai, C., & Zheng, Q. (2019) · Applied Sciences · doi:10.3390/app10010087 · Cited by 69
“…divided into two modules: one is based on the Region Proposal Network (RPN) are a proposal network module, which is used to generate candidate regions; the other is based on Faster R-CNN classification network module, which is used to detect and classify candidate regions generated by the RPN.…”
MethodSelf-citationA Review on Industrial Surface Defect Detection Based on Deep Learning Technology
Qi, S., Yang, J., & Zhong, Z. (2020) · International Conference on Machine Learning and Machine Intelligence (MLMI) · doi:10.1145/3426826.3426832 · Cited by 86
“[22] proposed an end-to-end surface defects recognition system for steel strip surface inspection.”
BackgroundAutomated steel surface defect detection and classification using a new deep learning-based approach
Demir, K., Ay, M., Çavaş, M., & Demir, F. (2022) · Neural Computing and Applications · doi:10.1007/s00521-022-08112-5 · Cited by 80
“Yie et al. [11] used a 14-layer CNN model with 5 convolutional layers.”
BackgroundMethodDeep Regression Neural Network for Industrial Surface Defect Detection
He, Z., & Liu, Q. (2020) · IEEE Access · doi:10.1109/access.2020.2975030 · Cited by 68
“images are taken from [2].”
Periodic Surface Defect Detection in Steel Plates Based on Deep Learning
Liu, Y., Xu, K., & Xu, J. (2019) · Applied Sciences · doi:10.3390/app9153127 · Cited by 58
“[7] proposed an end-to-end defect detection system for steel strips [7].”
BackgroundA Generic Semi-Supervised Deep Learning-Based Approach for Automated Surface Inspection
Zheng, X., Wang, H., Chen, J., Kong, Y., & Zheng, S. (2020) · IEEE Access · doi:10.1109/access.2020.3003588 · Cited by 58
“An end-to-end surface defect inspection method based on deep CNN [47] achieves an overall accuracy of 99.0%.”
MethodInfluentialBoudiaf, A., Benlahmidi, S., Harrar, K., & Zaghdoudi, R. (2022) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-022-01344-6 · Cited by 53
“[20] employed CNN to classify the defects with a classification accuracy of 99.”
MethodA sub-region Unet for weak defects segmentation with global information and mask-aware loss
Zhu, W., Liang, R., Yang, J., Cao, Y., Fu, G., & Cao, Y. (2023) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2023.106011 · Cited by 49
Hao, Z., Li, Z., Ren, F., Lv, S., & Ni, H. (2022) · Metals · doi:10.3390/met12020311 · Cited by 46
“[12] proposed an end-toend recognition system based on symmetric surround saliency map and deep convolutional neural network (CNN).”
BackgroundWang, Q., Yang, R., Wu, C., & Liu, Y. (2021) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.03.053 · Cited by 47
Chen, R., Cai, D., Hu, X., Zhan, Z., & Wang, S. (2021) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2021.3109723 · Cited by 42
Unveiling Patterns: A Study on Semi-Supervised Classification of Strip Surface Defects
Liu, Y., Yang, H., & Wu, C. (2023) · IEEE Access · doi:10.1109/access.2023.3326843 · Cited by 54
“Li et al. [29] designed an end-to-end defect classification system.”
BackgroundA Survey of Vision-Based Methods for Surface Defects’ Detection and Classification in Steel Products
Ibrahim, A. A. M. S., & Tapamo, J. (2024) · Informatics · doi:10.3390/informatics11020025 · Cited by 69
Automatic quality inspection in additive manufacturing using semi-supervised deep learning
Manivannan, S. (2022) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-022-02000-4 · Cited by 48
Selamet, F., Kaman, S. Ç., & Kotan, M. (2022) · IEEE Access · doi:10.1109/access.2022.3224037 · Cited by 44
“[17] proposed a defect detection system for steel strip surfaces based on CNN.”
MethodKonovalenko, І. V., Maruschak, P. O., Brevus, V., & Prentkovskis, O. (2021) · Metals · doi:10.3390/met11040549 · Cited by 40
“In [14], a surface defect recognition system for checking steel sheets was proposed.”
BackgroundFilippo, M. P., Gomes, O. D. F. M., da Costa, G. A. O. P., & Mota, G. L. A. (2021) · Minerals Engineering · doi:10.1016/j.mineng.2021.107007 · Cited by 38
Bouguettaya, A., Mentouri, Z., & Zarzour, H. (2023) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-023-10947-8 · Cited by 39
“…to the results presented in Table 3, our model achieves higher accuracy than AECLBP [3], DST– GLCM [1], Custom CNN architecture proposed in [25], VGG16-ADB [11], Improved VGG-19 [9], Finetuned CNN proposed in [10], CNN-T [12], and Multi-SE-ResNet34 with an attention mechanism [26] by…”
MethodLiang, Y., Xu, K., & Zhou, P. (2020) · Sensors · doi:10.3390/s20164519 · Cited by 39
“An end-to-end steel strip defect detection network model was outlined in [28]; this system is based on the symmetric surround saliency map for surface defects detection and deep convolutional neural networks (CNNs) for seven classes of steel strip defects classification.”
MethodSteel Strip Surface Defect Detection Method Based on Improved YOLOv5s
Lu, J., Zhu, M., Ma, X., & Wu, K. (2024) · Biomimetics · doi:10.3390/biomimetics9010028 · Cited by 36
“Li et al. [3] used a Symmetric Surround Saliency Map for surface defect detection and Deep Convolutional Neural Network (CNN) for strip steel defect classification using the NEU dataset.”
MethodRathi, S., Mirajkar, O., Shukla, S., Deshmukh, L., & Dangare, L. (2024) · Indian Journal of Information Sources and Services · doi:10.51983/ijiss-2024.14.1.4003 · Cited by 49
Fu, G., Jia, S., Zhu, W., Yang, J., Cao, Y., Yang, M. Y., & Cao, Y. (2022) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2022.109109 · Cited by 35
Ibrahim, A. A. M. S., & Tapamo, J. (2024) · Scientific African · doi:10.1016/j.sciaf.2024.e02066 · Cited by 50
A fast button surface defect detection method based on Siamese network with imbalanced samples
Wu, S., Wu, Y., Cao, D., & Zheng, C. (2019) · Multimedia Tools and Applications · doi:10.1007/s11042-019-08042-w · Cited by 33
A multi-class classifier based on support vector hyper-spheres for steel plate surface defects
Gong, R., Chu, M., Yang, Y., & Feng, Y. (2019) · Chemometrics and Intelligent Laboratory Systems · doi:10.1016/j.chemolab.2019.03.010 · Cited by 31
Saeedi, J., Dotta, M., Galli, A., Nasciuti, A., Maradia, U., Boccadoro, M., Gambardella, L. M., & Giusti, A. (2020) · Machine Vision and Applications · doi:10.1007/s00138-020-01142-w · Cited by 31
“However, the end-to-end approach combines feature extraction and the classification (or regression) processes into one whole using deep learning neural networks framework in which features are automatically extracted through the learning of training sets [25, 26].”
MethodCASPPNet: a chained atrous spatial pyramid pooling network for steel defect detection
Zheng, Z., Hu, Y., Zhang, Y., Yang, H., Qiao, Y., Qu, Z., & Huang, Y. (2022) · Measurement Science and Technology · doi:10.1088/1361-6501/ac68d2 · Cited by 31
“Besides, Yi et al utilized an end-to-end convolutional neural networks to extract steel defect mask from complex background and achieved a high recognition rate for defect images [19].”
Cao, Y., Zhu, W., Yang, J., Fu, G., Lin, D., & Cao, Y. (2022) · Optics and Lasers in Engineering · doi:10.1016/j.optlaseng.2022.107294 · Cited by 35
Real-Time Classification of Steel Strip Surface Defects Based on Deep CNNs
Liu, Y., Geng, J., Su, Z., Zhang, W., & Li, J. (2018) · Lecture notes in electrical engineering · doi:10.1007/978-981-13-2291-4_26 · Cited by 31
A survey on deep learning fundamentals
Tian, C., Cheng, T., Peng, Z., Zuo, W., Tian, Y., Zhang, Q., Wang, F., & Zhang, D. D. (2025) · Artificial Intelligence Review · doi:10.1007/s10462-025-11368-7 · Cited by 53
Zhao, J., Qian, X., Zhang, Y., Shan, D., Liu, X., Coleman, S., & Kerr, D. (2023) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-023-02080-w · Cited by 30
“However, the generation of defects belongs to small probability events, which makes it difficult to collect enough defect samples.”
An Improved YOLOX Model for Detecting Strip Surface Defects
Yi, C., Xu, B., Chen, J., Chen, Q., & Zhang, L. (2022) · steel research international · doi:10.1002/srin.202200505 · Cited by 31
Steel Strip Surface Defect Identification using Multiresolution Binarized Image Features
Mentouri, Z., Moussaoui, A., Boudjehem, D., & Doghmane, H. (2020) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-020-01012-7 · Cited by 29
Surface Defect Detection of Strip-Steel Based on an Improved PP-YOLOE-m Detection Network
Zhang, Y., Liu, X., Guo, J., & Zhou, P. (2022) · Electronics · doi:10.3390/electronics11162603 · Cited by 31
Surface Defects Classification of Hot Rolled Strip Based on Improved Convolutional Neural Network
Wang, W., Lu, K., Wu, Z., Long, H., Zhang, J., Chen, P., & Wang, B. (2021) · ISIJ International · doi:10.2355/isijinternational.isijint-2020-451 · Cited by 27
Surface defect detection method for air rudder based on positive samples
Yang, Z., Zhang, M., Chen, Y., Hu, N., Gao, L., Liu, L., Ping, E., & Song, J. I. (2022) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-022-02034-8 · Cited by 28
Mohandas, R., Mongan, P. G., & Hayes, M. J. (2024) · Sensors · doi:10.3390/s24206553 · Cited by 28
“Li et al. [58] proposed an end-to-end surface defect recognition system based on symmetric surround saliency maps for surface defects and a deep CNN for classifying seven categories of steel strip defects.”
BackgroundPractical Aspects of the Design and Use of the Artificial Neural Networks in Materials Engineering
Sitek, W., & Trzaska, J. (2021) · Metals · doi:10.3390/met11111832 · Cited by 24
Real-time system for automatic cold strip surface defect detection
Kostenetskiy, P., Alkapov, R., Vetoshkin, N., Chulkevich, R., Napolskikh, I., & Poponin, O. (2019) · FME Transactions · doi:10.5937/fmet1904765k · Cited by 23
Tang, W., Vian, C., Tang, Z., & Yang, B. (2021) · Machine Vision and Applications · doi:10.1007/s00138-021-01226-1 · Cited by 23
Real-time Steel Surface Defect Recognition Based on CNN
Litvintseva, A., Evstafev, O., & Shavetov, S. V. (2021) · IEEE International Conference on Automation Science and Engineering (CASE) · doi:10.1109/case49439.2021.9551414 · Cited by 24
Surface Defect Classification of Steel Strip with Few Samples Based on Dual‐Stream Neural Network
Zhang, J., Li, S., Yan, Y., Ni, Z., & Ni, H. (2021) · steel research international · doi:10.1002/srin.202100554 · Cited by 22
A Survey on Surface Defect Inspection Based on Generative Models in Manufacturing
He, Y., Li, S., Wen, X., & Xu, J. (2024) · Applied Sciences · doi:10.3390/app14156774 · Cited by 35
Nath, V., Chattopadhyay, C., & Desai, K. A. (2022) · Manufacturing Letters · doi:10.1016/j.mfglet.2022.10.001 · Cited by 22
A multi-scale pooling convolutional neural network for accurate steel surface defects classification
Fu, G., Zhang, Z., Le, W., Li, J., Zhu, Q., Niu, F., Chen, H., Sun, F., & Shen, Y. (2023) · Frontiers in Neurorobotics · doi:10.3389/fnbot.2023.1096083 · Cited by 24
“Moreover, several CNN-based approaches are also compared, including ETE (Li et al., 2016), DECAF+MLR (Ren et al.”
BackgroundMethodInfluentialHussain, T., Hong, J., & Seok, J. (2024) · Computers, materials & continua/Computers, materials & continua (Print) · doi:10.32604/cmc.2024.050884 · Cited by 21
DuAK: Reinforcement Learning-Based Knowledge Graph Reasoning for Steel Surface Defect Detection
Zhang, Y., Wang, H., Shen, W., & Peng, G. (2023) · IEEE Transactions on Automation Science and Engineering · doi:10.1109/tase.2023.3307588 · Cited by 22
STE-YOLO: A Surface Defect Detection Algorithm for Steel Strips
Li, D., Wang, E., Li, Z., Yin, Y., Zhang, L., & Zhao, C. (2024) · Electronics · doi:10.3390/electronics14010054 · Cited by 18
Nath, V., Chattopadhyay, C., & Desai, K. A. (2022) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2022.105553 · Cited by 17
An inspection method of rail head surface defect via bimodal structured light sensors
Zheng, J., Wang, L., Liu, J., Wang, S., Wang, S., Wang, L., & Zhang, J. (2022) · International Journal of Machine Learning and Cybernetics · doi:10.1007/s13042-022-01736-y · Cited by 15
“Moreover, in [21, 22], DCNNs have been used for steel surface defects, and achieved great results.”
BackgroundZaghdoudi, R., Séridi, H., Boudiaf, A., & Ziani, S. (2020) · International Conference on Advanced Aspects of Software Engineering (ICAASE) · doi:10.1109/icaase51408.2020.9380108 · Cited by 16
Optimization Algorithm of Steel Surface Defect Detection Based on YOLOv8n-SDEC
Jiang, X., Cui, Y., Cui, Y., Xu, R., Yang, J., & Zhou, J. (2024) · IEEE Access · doi:10.1109/access.2024.3426318 · Cited by 19
Nahar, L., Islam, M. S., Awrangjeb, M., & Verhoeve, R. (2024) · Computers in Industry · doi:10.1016/j.compind.2024.104187 · Cited by 19
TLU-Net: A Deep Learning Approach for Automatic Steel Surface Defect DetectionPreprint
Damacharla, P., V., A. R. M., Ringenberg, J., et al. (2022) · doi:10.31224/2679 · Cited by 14
A deep learning system for collotelinite segmentation and coal reflectance determination
Santos, R. B. M., Augusto, K. S., Iglesias, J. C. Á., Rodrigues, S., Paciornik, S., Esterle, J., & Domingues, A. L. A. (2022) · International Journal of Coal Geology · doi:10.1016/j.coal.2022.104111 · Cited by 15
Heat-loss cycle prediction in steelmaking plants through artificial neural network
Duarte, I. C. D., de Almeida, G. M., & Cardoso, M. (2020) · Journal of the Operational Research Society · doi:10.1080/01605682.2020.1824552 · Cited by 14
“Yi et al. (2017) used deep convolutional neural networks (CNNs) for end-to-end surface defects in steel strip surface.”
MethodXu, Y., Wang, D., Liu, H., Duan, B., & Yu, H. (2022) · steel research international · doi:10.1002/srin.202200284 · Cited by 13
Improved cross pattern approach for steel surface defect recognition
Mentouri, Z., Doghmane, H., Moussaoui, A., & Bourouba, H. (2020) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-06050-x · Cited by 15
Fu, G., Le, W., Zhang, Z., Li, J., Zhu, Q., Niu, F., Chen, H., Sun, F., & Shen, Y. (2023) · Machines · doi:10.3390/machines11010124 · Cited by 14
Manivannan, S. (2023) · Computers & Industrial Engineering · doi:10.1016/j.cie.2023.109766 · Cited by 17
Steel Surface Defect Detection Using Learnable Memory Vision Transformer
Ayon, S. T. K., Siraj, F. M., & Uddin, J. (2025) · Computers, materials & continua/Computers, materials & continua (Print) · doi:10.32604/cmc.2025.058361 · Cited by 29
Feng, X., Gao, X., & Luo, L. (2021) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2082/1/012016 · Cited by 13
“Y Liu et al [4] used GoogLeNet as the base model and added constant mapping to it to enhance the algorithm to some extent.”
MethodLow-pass U-Net: a segmentation method to improve strip steel defect detection
Liu, B., Yang, B., Zhao, Y., & Li, J. (2022) · Measurement Science and Technology · doi:10.1088/1361-6501/aca34a · Cited by 14
“Yi et al [17] designed an end-to-end surface defect recognition system based on a symmetric surround saliency map for surface defect detection.”
Detection of Scratch Defects on Metal Surfaces Based on MSDD-UNet
Liu, Y., Qin, Y., Lin, Z., Xia, H., & Wang, C. (2024) · Electronics · doi:10.3390/electronics13163241 · Cited by 12
“Compared to digital signal processing methods, deep learning methods, such as convolutional neural networks (CNNs), can automatically extract deep representative features end-to-end from data [8].”
MethodACA-Net: An Adaptive Convolution and Anchor Network for Metallic Surface Defect Detection
Chen, F., Deng, M., Gao, H., Yang, X., & Zhang, D. (2022) · Applied Sciences · doi:10.3390/app12168070 · Cited by 11
Surface Defects Classification of Hot Rolled Strip Based on Few-shot Learning
Wang, W., Wu, Z., Lu, K., Long, H., Li, D., Zhang, J., Chen, P., & Wang, B. (2022) · ISIJ International · doi:10.2355/isijinternational.isijint-2021-051 · Cited by 12
CNN‐based defect detection in manufacturing
Hou, M., Li, P., Cheng, S., & Yv, J. (2024) · Advanced Control for Applications · doi:10.1002/adc2.196 · Cited by 15
Boudiaf, A., Benlahmidi, S., Dahane, A., & Bouguettaya, A. (2024) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-024-01927-5 · Cited by 14
“Yi et al. [22] classified defects using a custom CNN with a classi-fication accuracy of 99.05%.”
InfluentialLi, L., Ren, T., & Feng, M. (2023) · Advances in Mechanical Engineering · doi:10.1177/16878132231218586 · Cited by 11
“Yi et al. 9 used a CNN to achieve a classification accuracy of 99.05%.”
MethodInfluentialTang, C., Feng, X., Wen, H., Xu, Z., Shao, Y., Zhou, X., Huang, B., & Li, Y. (2021) · Applied Sciences · doi:10.3390/app112210508 · Cited by 10
Self-citationDeveloping an explainable hybrid deep learning model in digital transformation: an empirical study
Chiu, M., Chiang, Y.-H., & Chiu, J.-E. (2023) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-023-02127-y · Cited by 11
“Yi et al., (2017) applied the CNN model to detect seven defects on the surface of a steel strip, but the model cannot be debugged when it is wrong, and it can only be optimized by repeatedly training the model.”
Metadata
- Authors
- Yi, L., Li, G., & Jiang, M.
- Affiliations
- College of Electronics and Information Engineering Tongji University Shanghai 201804 PR China
- Tongji University (CN)
- Venue
- steel research international
- Publisher
- Wiley
- Published
- 2016-04-13
- Volume
- 88
- Issue
- 2
- ISSN
- 1611-3683 (ISSN-L)
- 1869-344X
- OpenAlex
- W2337601638
- Semantic Scholar
- 0f449f26897fe7aa65bd14dc790d887b52431e24
- Cited by
- 173
- References
- 20
- Citations by year
- 2026: 8 · 2025: 15 · 2024: 32 · 2023: 24 · 2022: 29 · 2021: 25 · 2020: 22 · 2019: 12 · 2018: 5 · 2017: 1
- FWCI
- 8.14
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- steel research international (publishedVersion)
- Funders
- Baosteel Group and Baosight Software Company
- Topics
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Industrial Vision Systems and Defect Detection
- Physical Sciences › Engineering › Mechanical Engineering › Non-Destructive Testing Techniques
- Physical Sciences › Engineering › Civil and Structural Engineering › Infrastructure Maintenance and Monitoring
- Keywords
- defect detection, end-to-end recognition, convolutional neural networks, defect classification, data augmentation, overfitting
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.