The DOI matches its Crossref record; 23 of the 23 references it cites were found in a registry or an index; 3 of the 21 sources its claims cite were checked for support.
Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl2
Open accessAbstract
The influence of KCl, NaCl and CaCl 2 on the oxidation of 304-type (Fe18Cr10Ni) stainless steel at 600 °C in 5 %O 2 + 40 %H 2 O was investigated. Prior to exposure, a small amount of the preferred salt (cation equivalent: 1.35 μmol/cm 2 ) was deposited on the samples. Exposure time was 1–168 h. The oxidized samples were analyzed by SEM/EDX, XRD, FIB and IC. The presence of KCl and NaCl strongly accelerates high temperature corrosion of 304L. Corrosion attack is initiated by the formation of alkali chromate through the reaction of alkali with the protective oxide. Chromate formation is a sink for chromium in the oxide and leads to a loss of its protective properties. Subsequently a rapidly growing scale forms, consisting of an outer hematite layer with chromate particles on top and an inner spinel oxide layer. In contrast to NaCl and KCl, CaCl 2 is not very corrosive. At temperature, CaCl 2 is rapidly converted to CaO. Small amounts of CaCrO 4 form where CaO is in direct contact with the scale. CaO also reacts with the scale to form Ca 2 Fe 2 O 5 .
Overview
CoChat Summary
TL;DR
KCl and NaCl strongly accelerate high-temperature corrosion of 304L stainless steel at 600 °C in 5% O₂ + 40% H₂O by forming alkali chromates that deplete chromium from the protective oxide, while CaCl₂ is only slightly corrosive because it rapidly converts to CaO. The resulting thick scale consists of outer hematite and inner spinel oxide, with chromate particles on top.
Key findings
- NaCl and KCl both caused strong mass gain and breakdown of the protective oxide; NaCl initially caused higher mass gain than KCl, but the two mass-gain curves were similar during later stages. CaCl₂ did not significantly increase mass gain compared with salt-free reference exposures.
- Chromate formation was detected early: after 1 h, about 80% of applied alkali and about 60% of added chlorine were detected for NaCl/KCl. After 24 h, 44% of Na⁺ remained for NaCl versus 19% of K⁺ for KCl; chromate formation was 30% of theoretical yield for NaCl and 20% for KCl. After 168 h, chromate was 33% for NaCl and 11% for KCl.
- For CaCl₂, after 1 h 52% of applied Ca²⁺ and 12% of chloride remained; chromate formation was 2% of theoretical yield, rising only to 4% at 24 h and 5% at 168 h. CaCl₂ converted to CaO, with small amounts of CaCrO₄ and Ca₂Fe₂O₅.
- Corrosion products on NaCl/KCl-treated samples included outer hematite (Fe₂O₃), inner spinel-type oxide (Fe, Cr, Ni)₃O₄, and alkali chromate (Na₂CrO₄ or K₂CrO₄). NaCl-treated samples also formed a product containing Na, Fe and O, possibly Na₂Fe₂O₄.
Methods
- Austenitic stainless steel 304L (Fe18Cr10Ni) samples, 5.56 cm², were polished and sprayed with NaCl, KCl or CaCl₂ to a cation equivalent of 1.35 µmol/cm².
- Isothermal exposures were performed in a silica tube furnace at 600 °C (±1 °C) in 5% O₂ + 40% H₂O with N₂ carrier gas, flow rate 2.5 cm/s, for 1, 24, 72 or 168 h.
- Samples were analyzed by gravimetry, SEM/EDX, grazing-incidence XRD, FIB cross sections, and ion chromatography for water-soluble cations and anions.
Limitations
- The paper states that ion chromatography analyses had a relative standard deviation of about ±5%; unaccounted Ca²⁺ was attributed mainly to Ca₂Fe₂O₅ and substantial scale spallation, and unaccounted chloride mainly to thermal decomposition/evaporation.
- The paper states that the slightly lower mass gain of CaCl₂-exposed samples compared with salt-free exposures was not considered significant because of substantial scale spallation at former CaCl₂ agglomerations.
- Evident from the text: no explicit limitations section is provided; the study covers only one alloy (304L), one temperature (600 °C), one gas composition, and exposures up to 168 h. Some proposed phases, such as Na₂Fe₂O₄ and calcium hydroxy-/oxy-chlorides, are described as possible or poorly crystalline rather than directly confirmed by XRD.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
3 Valid · 5 Not valid · 16 Not checked · 122 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Thus, a two layered oxide scale has formed beneath the former salt particle, consisting of an outer iron-rich layer and an inner layer containing iron, chromium and nickel.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Corrosion Product Characterization
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A thick layered oxide scale has formed beneath the former NaCl crystal.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Corrosion Product Characterization
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In the case of KCl the amount of potassium ions found after 24 h corresponds to the amount of chromate detected.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Analysis of Water Soluble Compounds
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The presence of KCl and NaCl strongly accelerates high temperature corrosion of 304L.”
- Also stated in: § Gravimetry · boosted
“The results show that both NaCl and KCl strongly accelerate corrosion.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Abstract
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on an assumption not shown here.
- Also stated in: § Gravimetry · boosted
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“At this stage the NaCl treated sample exhibit considerably more corrosion between the salt particles than in the case of KCl.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Surface Morphology
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
95 more claims
Create a free account to see all 146 claims and every source verdict.
- Probably not a substantial claim. 12
- Borderline: one of the tests for a substantial claim is unclear. 2
- It may state two separate claims as one. 32
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Analysis of Water Soluble Compounds
“1.35 lmol of K ? was added per sample.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Sample Preparation
“The samples were coated with the preferred salt (NaCl, KCl or CaCl 2 ) to a cation equivalent of 1.35 lmol/cm 2 .”
Citations
Cites
Thermochemical Data of Pure Substances
Barin, I. (1995) · doi:10.1002/9783527619825 · Cited by 4,241
Gmelins Handbuch der Anorganischen Chemie.
(1958) · Zeitschrift für Physikalische Chemie · doi:10.1524/zpch.1958.18.5_6.406 · Cited by 899
The implications of chlorine-associated corrosion on the operation of biomass-fired boilers
Nielsen, H. P., Frandsen, F. J., Dam-Johansen, K., & Baxter, L. L. (2000) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(00)00003-4 · Cited by 785
Grabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Asteman, H., Svensson, J.-E., Norell, M., & Johansson, L.-G. (2000) · Oxidation of Metals · doi:10.1023/a:1004642310974 · Cited by 325
Self-citationAsteman, H., Svensson, J.-E., Johansson, L.-G., & Norell, M. (1999) · Oxidation of Metals · doi:10.1023/a:1018875024306 · Cited by 304
Self-citationDeposition and high temperature corrosion in a 10 MW straw fired boiler
Michelsen, H. P., Frandsen, F., Dam-Johansen, K., & Larsen, O. H. (1998) · Fuel Processing Technology · doi:10.1016/s0378-3820(97)00062-3 · Cited by 258
KCl Induced Corrosion of a 304-type Austenitic Stainless Steel at 600°C; The Role of Potassium
Pettersson, J., Asteman, H., Svensson, J. E., & Johansson, L. G. (2005) · Oxidation of Metals · doi:10.1007/s11085-005-5704-3 · Cited by 182
Self-citationHalvarsson, M., Tang, J. E., Asteman, H., Svensson, J.-E., & Johansson, L.-G. (2006) · Corrosion Science · doi:10.1016/j.corsci.2005.08.012 · Cited by 146
Self-citationZahs, A., Spiegel, M., & Grabke, H. J. (1999) · Materials and Corrosion · doi:10.1002/(sici)1521-4176(199910)50:10<561::aid-maco561>3.0.co;2-l · Cited by 146
Cited by
Ma, W., Wenga, T., Frandsen, F. J., Yan, B., & Chen, G. (2020) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2019.100789 · Cited by 275
Thunman, H., Lind, F., Breitholtz, C., Berguerand, N., & Seemann, M. C. (2013) · Fuel · doi:10.1016/j.fuel.2013.05.073 · Cited by 152
Karlsson, S., Åmand, L.-E., & Liske, J. (2015) · Fuel · doi:10.1016/j.fuel.2014.09.007 · Cited by 79
Self-citationStudies on the corrosion behavior of Fe-20Cr alloy in NaCl solution spray at 600 °C
Cao, M., Liu, L., Yu, Z., Fan, L., Li, Y., & Wang, F. (2018) · Corrosion Science · doi:10.1016/j.corsci.2018.01.033 · Cited by 66
Israelsson, N., Unocic, K. A., Hellström, K., Jonsson, T., Norell, M., Svensson, J.-E., & Johansson, L.-G. (2015) · Oxidation of Metals · doi:10.1007/s11085-015-9546-3 · Cited by 54
Self-citation
Metadata
- Authors
- Karlsson, S., Pettersson, J., Johansson, L. G., & Svensson, J. E.
- Affiliations
- Chalmers University of Technology (SE)
- Corresponding author
- Karlsson, S.
- Venue
- Oxidation of Metals
- Published
- 2012-04-27
- Volume
- 78
- Issue
- 1-2
- Pages
- 83-102
- ISSN
- 0030-770X (ISSN-L)
- 1573-4889
- OpenAlex
- W2019797599
- Cited by
- 118
- References
- 23
- Citations by year
- 2026: 10 · 2025: 9 · 2024: 12 · 2023: 7 · 2022: 12 · 2021: 8 · 2020: 5 · 2019: 11 · 2018: 4 · 2017: 7 · 2016: 14 · 2015: 7 · 2014: 7 · 2013: 4 · 2012: 1
- FWCI
- 10.22
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- Locations
- Oxidation of Metals (publishedVersion, cc-by)
- Chalmers Publication Library (Chalmers University of Technology) (submittedVersion)
- Chalmers Research (Chalmers University of Technology) (submittedVersion)
- Funders
- Chalmers Tekniska Högskola
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Physical Sciences › Materials Science › Materials Chemistry › Corrosion Behavior and Inhibition
- Keywords
- high-temperature corrosion, 304L stainless steel, sodium chloride, KCl, calcium chloride, chromium depletion, spinel oxides, calcium chromate, calcium oxide, Ca2Fe2O5, water vapor oxidation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-09-30, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-09-30 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl2. https://app.cochat.ai/papers/10.1007/s11085-012-9293-7
- The paper
- Karlsson, S., Pettersson, J., Johansson, L. G., & Svensson, J. E. (2012). Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl2. Oxidation of Metals. https://doi.org/10.1007/s11085-012-9293-7
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.