The DOI matches its Crossref record; 23 of the 23 references it cites were found in a registry or an index; 3 of the 21 sources its claims cite were checked for support.
Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl2
Open accessAbstract
The influence of KCl, NaCl and CaCl 2 on the oxidation of 304-type (Fe18Cr10Ni) stainless steel at 600 °C in 5 %O 2 + 40 %H 2 O was investigated. Prior to exposure, a small amount of the preferred salt (cation equivalent: 1.35 μmol/cm 2 ) was deposited on the samples. Exposure time was 1–168 h. The oxidized samples were analyzed by SEM/EDX, XRD, FIB and IC. The presence of KCl and NaCl strongly accelerates high temperature corrosion of 304L. Corrosion attack is initiated by the formation of alkali chromate through the reaction of alkali with the protective oxide. Chromate formation is a sink for chromium in the oxide and leads to a loss of its protective properties. Subsequently a rapidly growing scale forms, consisting of an outer hematite layer with chromate particles on top and an inner spinel oxide layer. In contrast to NaCl and KCl, CaCl 2 is not very corrosive. At temperature, CaCl 2 is rapidly converted to CaO. Small amounts of CaCrO 4 form where CaO is in direct contact with the scale. CaO also reacts with the scale to form Ca 2 Fe 2 O 5 .
Overview
CoChat Summary
TL;DR
KCl and NaCl strongly accelerate high-temperature corrosion of 304L stainless steel at 600 °C in 5% O₂ + 40% H₂O by forming alkali chromates that deplete chromium from the protective oxide, while CaCl₂ is only slightly corrosive because it rapidly converts to CaO. The resulting thick scale consists of outer hematite and inner spinel oxide, with chromate particles on top.
Key findings
- NaCl and KCl both caused strong mass gain and breakdown of the protective oxide; NaCl initially caused higher mass gain than KCl, but the two mass-gain curves were similar during later stages. CaCl₂ did not significantly increase mass gain compared with salt-free reference exposures.
- Chromate formation was detected early: after 1 h, about 80% of applied alkali and about 60% of added chlorine were detected for NaCl/KCl. After 24 h, 44% of Na⁺ remained for NaCl versus 19% of K⁺ for KCl; chromate formation was 30% of theoretical yield for NaCl and 20% for KCl. After 168 h, chromate was 33% for NaCl and 11% for KCl.
- For CaCl₂, after 1 h 52% of applied Ca²⁺ and 12% of chloride remained; chromate formation was 2% of theoretical yield, rising only to 4% at 24 h and 5% at 168 h. CaCl₂ converted to CaO, with small amounts of CaCrO₄ and Ca₂Fe₂O₅.
- Corrosion products on NaCl/KCl-treated samples included outer hematite (Fe₂O₃), inner spinel-type oxide (Fe, Cr, Ni)₃O₄, and alkali chromate (Na₂CrO₄ or K₂CrO₄). NaCl-treated samples also formed a product containing Na, Fe and O, possibly Na₂Fe₂O₄.
Methods
- Austenitic stainless steel 304L (Fe18Cr10Ni) samples, 5.56 cm², were polished and sprayed with NaCl, KCl or CaCl₂ to a cation equivalent of 1.35 µmol/cm².
- Isothermal exposures were performed in a silica tube furnace at 600 °C (±1 °C) in 5% O₂ + 40% H₂O with N₂ carrier gas, flow rate 2.5 cm/s, for 1, 24, 72 or 168 h.
- Samples were analyzed by gravimetry, SEM/EDX, grazing-incidence XRD, FIB cross sections, and ion chromatography for water-soluble cations and anions.
Limitations
- The paper states that ion chromatography analyses had a relative standard deviation of about ±5%; unaccounted Ca²⁺ was attributed mainly to Ca₂Fe₂O₅ and substantial scale spallation, and unaccounted chloride mainly to thermal decomposition/evaporation.
- The paper states that the slightly lower mass gain of CaCl₂-exposed samples compared with salt-free exposures was not considered significant because of substantial scale spallation at former CaCl₂ agglomerations.
- Evident from the text: no explicit limitations section is provided; the study covers only one alloy (304L), one temperature (600 °C), one gas composition, and exposures up to 168 h. Some proposed phases, such as Na₂Fe₂O₄ and calcium hydroxy-/oxy-chlorides, are described as possible or poorly crystalline rather than directly confirmed by XRD.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
3 Valid · 5 Not valid · 16 Not checked · 122 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Thus, a two layered oxide scale has formed beneath the former salt particle, consisting of an outer iron-rich layer and an inner layer containing iron, chromium and nickel.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Corrosion Product Characterization
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A thick layered oxide scale has formed beneath the former NaCl crystal.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Corrosion Product Characterization
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In the case of KCl the amount of potassium ions found after 24 h corresponds to the amount of chromate detected.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Analysis of Water Soluble Compounds
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The presence of KCl and NaCl strongly accelerates high temperature corrosion of 304L.”
- Also stated in: § Gravimetry · boosted
“The results show that both NaCl and KCl strongly accelerate corrosion.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Abstract
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on an assumption not shown here.
- Also stated in: § Gravimetry · boosted
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“At this stage the NaCl treated sample exhibit considerably more corrosion between the salt particles than in the case of KCl.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Surface Morphology
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
95 more claims
Create a free account to see all 146 claims and every source verdict.
- Probably not a substantial claim. 12
- Borderline: one of the tests for a substantial claim is unclear. 2
- It may state two separate claims as one. 32
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Analysis of Water Soluble Compounds
“1.35 lmol of K ? was added per sample.”
§ Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl 2 > Sample Preparation
“The samples were coated with the preferred salt (NaCl, KCl or CaCl 2 ) to a cation equivalent of 1.35 lmol/cm 2 .”
Citations
Cites
Thermochemical Data of Pure Substances
Barin, I. (1995) · doi:10.1002/9783527619825 · Cited by 4,241
Gmelins Handbuch der Anorganischen Chemie.
(1958) · Zeitschrift für Physikalische Chemie · doi:10.1524/zpch.1958.18.5_6.406 · Cited by 899
The implications of chlorine-associated corrosion on the operation of biomass-fired boilers
Nielsen, H. P., Frandsen, F. J., Dam-Johansen, K., & Baxter, L. L. (2000) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(00)00003-4 · Cited by 785
Grabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Asteman, H., Svensson, J.-E., Norell, M., & Johansson, L.-G. (2000) · Oxidation of Metals · doi:10.1023/a:1004642310974 · Cited by 325
Self-citationAsteman, H., Svensson, J.-E., Johansson, L.-G., & Norell, M. (1999) · Oxidation of Metals · doi:10.1023/a:1018875024306 · Cited by 304
Self-citationDeposition and high temperature corrosion in a 10 MW straw fired boiler
Michelsen, H. P., Frandsen, F., Dam-Johansen, K., & Larsen, O. H. (1998) · Fuel Processing Technology · doi:10.1016/s0378-3820(97)00062-3 · Cited by 258
KCl Induced Corrosion of a 304-type Austenitic Stainless Steel at 600°C; The Role of Potassium
Pettersson, J., Asteman, H., Svensson, J. E., & Johansson, L. G. (2005) · Oxidation of Metals · doi:10.1007/s11085-005-5704-3 · Cited by 182
Self-citationHalvarsson, M., Tang, J. E., Asteman, H., Svensson, J.-E., & Johansson, L.-G. (2006) · Corrosion Science · doi:10.1016/j.corsci.2005.08.012 · Cited by 146
Self-citationZahs, A., Spiegel, M., & Grabke, H. J. (1999) · Materials and Corrosion · doi:10.1002/(sici)1521-4176(199910)50:10<561::aid-maco561>3.0.co;2-l · Cited by 146
Cited by
Ma, W., Wenga, T., Frandsen, F. J., Yan, B., & Chen, G. (2020) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2019.100789 · Cited by 275
Thunman, H., Lind, F., Breitholtz, C., Berguerand, N., & Seemann, M. C. (2013) · Fuel · doi:10.1016/j.fuel.2013.05.073 · Cited by 174
Karlsson, S., Åmand, L.-E., & Liske, J. (2015) · Fuel · doi:10.1016/j.fuel.2014.09.007 · Cited by 79
“However, during corrosion initiation little or no chlorine have been detected in the corrosion product layer, indicating that the HCl(g) formed is released to the flue gas [7,9].”
BackgroundSelf-citationStudies on the corrosion behavior of Fe-20Cr alloy in NaCl solution spray at 600 °C
Cao, M., Liu, L., Yu, Z., Fan, L., Li, Y., & Wang, F. (2018) · Corrosion Science · doi:10.1016/j.corsci.2018.01.033 · Cited by 66
Israelsson, N., Unocic, K. A., Hellström, K., Jonsson, T., Norell, M., Svensson, J.-E., & Johansson, L.-G. (2015) · Oxidation of Metals · doi:10.1007/s11085-015-9546-3 · Cited by 54
Self-citationEklund, J., Jönsson, B., Persdotter, A., Liske, J., Svensson, J.-E., & Jonsson, T. (2018) · Corrosion Science · doi:10.1016/j.corsci.2018.09.004 · Cited by 55
Self-citationCorrosion Problems in Incinerators and Biomass-Fuel-Fired Boilers
Mudgal, D., Singh, S., & Prakash, S. (2014) · International Journal of Corrosion · doi:10.1155/2014/505306 · Cited by 56
Okoro, S. C., Montgomery, M., Frandsen, F., & Pantleon, K. (2014) · Energy & Fuels · doi:10.1021/ef5017335 · Cited by 48
Karlsson, S., Jonsson, T., Hall, J., Svensson, J., & Liske, J. (2014) · Energy & Fuels · doi:10.1021/ef402127h · Cited by 40
Self-citationUse of alkali-feldspar as bed material for upgrading a biomass-derived producer gas from a gasifier
Berguerand, N., Maric, J., Vilches, T. B., & Thunman, H. (2016) · Chemical Engineering Journal · doi:10.1016/j.cej.2016.02.060 · Cited by 49
Effect of grain size on high-temperature corrosion performance of laser cladding inconel 625 coating
Peng, J., Li, K., Xie, Z., Tan, L., Wang, Y., Liu, F., & Liu, Y. (2024) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2024.10.052 · Cited by 41
High-Temperature Oxidation and Decarburization of 14.55 wt pct Cr-Cast Iron in Dry Air Atmosphere
Efremenko, V. G., Chabak, Y. G., Lekatou, A. G., Karantzalis, A. E., & Efremenko, А. V. (2016) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-016-3336-7 · Cited by 40
Fagerström, J., Näzelius, I.-L., Gilbe, C., Boström, D., Öhman, M. C., & Boman, C. (2014) · Energy & Fuels · doi:10.1021/ef4023543 · Cited by 39
Phother-Simon, J., Hanif, I., Liske, J., & Jonsson, T. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109315 · Cited by 37
Sulfation of Condensed Potassium Chloride by SO2
Sengeløv, L. W., Hansen, T. B., Bartolomé, C., Wu, H., Pedersen, K., Frandsen, F., Jensen, A. D., & Glarborg, P. (2013) · Energy & Fuels · doi:10.1021/ef400405z · Cited by 38
Mudgal, D., Kumar, S., Singh, S. P., & Prakash, S. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-1177-3 · Cited by 34
Liu, X., Duan, Y., Zheng, L., Long, L., Khalid, Z., Huang, Q., & Jiang, X. (2023) · Fuel · doi:10.1016/j.fuel.2023.129524 · Cited by 32
Hot Corrosion Behavior of Some Superalloys in a Simulated Incinerator Environment at 900 °C
Mudgal, D., Singh, S. P., & Prakash, S. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0721-x · Cited by 29
Arivarasu, M., Kannan, M. V., Ramkumar, K. D., & Arivazhagan, N. (2017) · Corrosion Engineering Science and Technology The International Journal of Corrosion Processes and Corrosion Control · doi:10.1080/1478422x.2016.1213061 · Cited by 30
Okoro, S. C., Kiamehr, S., Montgomery, M., Frandsen, F. J., & Pantleon, K. (2017) · Materials and Corrosion · doi:10.1002/maco.201609173 · Cited by 27
Cyclic Corrosion and Chlorination of an FeCrAl Alloy in the Presence of KCl
Israelsson, N., Unocic, K. A., Hellström, K., Svensson, J. E., & Johansson, L. (2015) · Oxidation of Metals · doi:10.1007/s11085-015-9554-3 · Cited by 29
Self-citationSui, J., Lehmusto, J., Bergelin, M., & Hupa, L. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.04.010 · Cited by 26
Eklund, J., Hanif, I., Bigdeli, S., & Jonsson, T. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110114 · Cited by 26
Wenga, T., Chen, G., Ma, W., & Yan, B. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.04.013 · Cited by 26
Ssenteza, V., Eklund, J., Hanif, I., Liske, J., & Jonsson, T. (2023) · Corrosion Science · doi:10.1016/j.corsci.2022.110896 · Cited by 25
Persdotter, A., Sattari, M., Larsson, E., Ogaz, M. A. O., Liske, J., & Jonsson, T. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.108234 · Cited by 26
Corrosion of furnace wall materials in waste-wood fired power plant
Alipour, Y., & Henderson, P. (2014) · Corrosion Engineering Science and Technology The International Journal of Corrosion Processes and Corrosion Control · doi:10.1179/1743278214y.0000000228 · Cited by 24
Eklund, J., Persdotter, A., Hanif, I., Bigdeli, S., & Jonsson, T. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109584 · Cited by 23
Effect of Mo on corrosion behavior of Ni20Cr– x Mo alloys in air with NaCl–KCl–CaCl 2 vapor at 570°C
Izzuddin, H., Hayashi, S., Yoneda, S., Kogin, T., Ishikawa, E., & Noguchi, M. (2020) · Materials and Corrosion · doi:10.1002/maco.201911469 · Cited by 21
The long-term corrosion behavior of fecral(Si) alloys after breakaway oxidation at 600 °C
Eklund, J., Persdotter, A., Ssenteza, V., & Jonsson, T. (2023) · Corrosion Science · doi:10.1016/j.corsci.2023.111155 · Cited by 22
Ma, W., Zeng, S., & Wenga, T. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.11.175 · Cited by 20
Alipour, Y., Henderson, P., & Szakálos, P. (2013) · Materials and Corrosion · doi:10.1002/maco.201307118 · Cited by 23
The Effects of KCl, NaCl and K2CO3 on the High-Temperature Oxidation Onset of Sanicro 28 Steel
Sui, J., Lehmusto, J., Bergelin, M., & Hupa, M. (2016) · Oxidation of Metals · doi:10.1007/s11085-016-9613-4 · Cited by 19
Bigdeli, S., Kjellqvist, L., Naraghi, R., Höglund, L., Larsson, H., & Jonsson, T. (2021) · Journal of Phase Equilibria and Diffusion · doi:10.1007/s11669-021-00893-x · Cited by 19
Cantatore, V., Ogaz, M. A. O., Liske, J., Jonsson, T., Svensson, J., Johansson, L., & Panas, I. (2019) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.9b06497 · Cited by 22
Self-citationEklund, J., Paz, M. D., Jönsson, B., Liske, J., Svensson, J., & Jonsson, T. (2019) · Materials and Corrosion · doi:10.1002/maco.201810618 · Cited by 18
Self-citationLong-term Hot Corrosion Behavior of Boiler Tube Alloys in Waste-to-Energy Plants
Liu, J., Dyson, D., & Asselin, E. (2016) · Oxidation of Metals · doi:10.1007/s11085-016-9627-y · Cited by 18
Blomberg, T., Tripathi, T. S., & Karppinen, M. J. (2019) · RSC Advances · doi:10.1039/c9ra00582j · Cited by 21
Cai, Y., Nguyen, T. D., Zhang, J., Gleeson, B. T., & Young, D. J. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.110001 · Cited by 15
High temperature corrosion memory in a waste fired boiler – Influence of sulfur
Paz, M. D., Phother-Simon, J., Andersson, S., & Jonsson, T. (2021) · Waste Management · doi:10.1016/j.wasman.2021.05.005 · Cited by 17
Leban, M. B., Vončina, M., Kosec, T., Tisu, R., Barborič, M., & Medved, J. (2022) · High Temperature Corrosion of Materials · doi:10.1007/s11085-022-10138-y · Cited by 16
Persdotter, A., Boll, T., & Jonsson, T. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109779 · Cited by 16
Khantisopon, K., Tharajak, J., Nawarat, P., Sanpo, N., & Ang, A. S. M. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110470 · Cited by 16
Alipour, Y., Talus, A., Henderson, P., & Norling, R. (2015) · Fuel Processing Technology · doi:10.1016/j.fuproc.2015.07.014 · Cited by 16
A Comparative Study of the Initial Corrosion of KCl and PbCl2 on a Low-Alloyed Steel
Larsson, E., Gruber, H., Hellström, K., Jonsson, T., Liske, J., & Svensson, J. E. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9765-x · Cited by 14
Self-citationPham, S. T., Tieu, A. K., Wan, S., Lei, W., Liu, D., & Tran, N. V. (2021) · Applied Surface Science · doi:10.1016/j.apsusc.2021.150556 · Cited by 15
Lu, J., Huang, J., Yang, Z. Z., Zhou, Y., Dang, Y., Yuan, Y., & Gu, Y. (2019) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-019-04515-z · Cited by 15
Application of aluminum diffusion coatings to mitigate the KCl‐induced high‐temperature corrosion
Kiamehr, S., Lomholt, T. N., Dahl, K. V., Christiansen, T. L., & Somers, M. A. J. (2016) · Materials and Corrosion · doi:10.1002/maco.201609047 · Cited by 17
A Laboratory Study of the in Situ Sulfation of Alkali Chloride Rich Deposits: Corrosion Perspective
Karlsson, S., Larsson, E., Jonsson, T., Svensson, J.-E., & Liske, J. (2016) · Energy & Fuels · doi:10.1021/acs.energyfuels.6b00372 · Cited by 16
Self-citationOkoro, S. C., Montgomery, M., Frandsen, F., & Pantleon, K. (2015) · Materials at High Temperatures · doi:10.1179/0960340914z.00000000081 · Cited by 16
Effect of microstructure on KCl corrosion attack of modified AISI 310 steel
Malede, Y. C., Montgomery, M., Dahl, K. V., & Hald, J. K. (2017) · Materials at High Temperatures · doi:10.1080/09603409.2017.1389381 · Cited by 12
Sun, Q., Zhang, B., Zhang, D., Yang, Y., Lin, J., & Wang, F. (2023) · Materials Characterization · doi:10.1016/j.matchar.2023.112885 · Cited by 12
Characterization of pack cemented Ni2Al3 coating exposed to KCl(s) induced corrosion at 600 °C
Dahl, K. V., Slomian, A., Lomholt, T. N., Kiamehr, S., Grumsen, F. B., Montgomery, M., & Jonsson, T. (2017) · Materials at High Temperatures · doi:10.1080/09603409.2017.1392112 · Cited by 12
Agüero, A., Baráibar, I., González, V., Muelas, R., & Plana, D. (2015) · Oxidation of Metals · doi:10.1007/s11085-015-9575-y · Cited by 13
Liu, B., & Chen, X. (2018) · Oxidation of Metals · doi:10.1007/s11085-018-9864-3 · Cited by 12
Olivas-Ogaz, M. A., Eklund, J., Svensson, J.-E., Liske, J., & Jonsson, T. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9763-z · Cited by 13
Self-citationRamandhany, S., Triyono, D., Sugiarti, E., Wismogroho, A. S., Izzuddin, H., Afandi, A. M., Widayatno, W. B., Desiati, R. D., & Sundawa, R. Y. (2024) · Journal of Thermal Spray Technology · doi:10.1007/s11666-024-01720-8 · Cited by 13
Role of calcium ion in moso bamboo pyrolysis under microwave irradiation
Dong, Q., Ren, S., Zhang, S., Huang, S., Guo, Y., Li, H., Nie, L., Sun, Z., & Du, Y. (2020) · Fuel Processing Technology · doi:10.1016/j.fuproc.2020.106598 · Cited by 12
Furugaki, T., Takahashi, H., & Hayashi, S. (2022) · Oxidation of Metals · doi:10.1007/s11085-022-10135-1 · Cited by 12
Corrosion behavior and mechanism of GH3539 alloy in molten NaCl-KCl-CaCl2 salts at 800 °C
Yan, J., Liu, W., & Tang, Z. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.112942 · Cited by 11
Mori, G., Vidic, K., Bucher, E., Yasir, M., Hornauer, D., Nachtnebel, M., Fitzek, H., & Schroettner, H. (2019) · Materials and Corrosion · doi:10.1002/maco.201810451 · Cited by 11
The Influence of KCl and HCl on the High-Temperature Oxidation of a Fe-2.25Cr-1Mo Steel at 400 °C
Larsson, E., Liske, J., Persdotter, A., Jonsson, T., Svensson, J., & Johansson, L.-G. (2019) · Oxidation of Metals · doi:10.1007/s11085-019-09943-9 · Cited by 12
Self-citationA microscopy study of nickel-based superalloys performance in type I hot corrosion conditions
Waeytens, M., Syed, A. U., Roberts, T., Martinez, F. D., Gray, S., & Nicholls, J. R. (2023) · Materials at High Temperatures · doi:10.1080/09603409.2023.2188355 · Cited by 12
Evaluation of High Temperature Corrosion in Simulated Waste Incinerator Environments
Alcántara-Cárdenas, J. A., Ramírez-López, A., Chávez, F., & Sánchez-Pastén, M. (2016) · Oxidation of Metals · doi:10.1007/s11085-016-9615-2 · Cited by 11
Cai, Y., Nguyen, T. D., Zhang, J., Gleeson, B. T., & Young, D. J. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110822 · Cited by 9
A comparative evaluation of waste wood and herbaceous biomass fireside corrosion behaviours
Sanusi, T., Sumner, J., & Simms, N. J. (2022) · Fuel · doi:10.1016/j.fuel.2022.124070 · Cited by 10
Wang, X., Fu, K., Ren, X., Xue, Y., & Luan, B. (2025) · Surfaces and Interfaces · doi:10.1016/j.surfin.2025.107190 · Cited by 16
Investigating corrosion memory: The influence of previous boiler operation on current corrosion rate
Paz, M. D., Zhao, D., Karlsson, S., Liske, J., & Jonsson, T. (2016) · Fuel Processing Technology · doi:10.1016/j.fuproc.2016.09.018 · Cited by 9
Self-citationLiu, X., Chen, Q., Long, L., Meng, X., Lv, G., Huang, Q., & Jiang, X. (2021) · Waste Disposal & Sustainable Energy · doi:10.1007/s42768-021-00087-8 · Cited by 8
Fireside corrosion and deposition on heat exchangers in biomass combustion systems
Mori, S., Sanusi, T., Simms, N., & Sumner, J. (2023) · Materials at High Temperatures · doi:10.1080/09603409.2022.2138007 · Cited by 8
“the effects of different deposits on the formation of K2 CrO4 on stainless steel could only confirm the presence of such compounds [19].”
BackgroundEffect of Different Vanadate Salt Composition on Oil Ash Corrosion of Boilers
Montero, X., & Galetz, M. C. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9795-4 · Cited by 9
The analysis of furnace wall deposits in a low-NOx waste wood-fired bubbling fluidised bed boiler
Alipour, Y., Viklund, P., & Henderson, P. (2012) · KTH Publication Database DiVA (KTH Royal Institute of Technology) · Cited by 8
Kaczmarczyk, R., & Gurgul, S. (2024) · Energies · doi:10.3390/en17133223 · Cited by 8
Ma, W., Zeng, S., & Wenga, T. (2024) · Corrosion Science · doi:10.1016/j.corsci.2024.112128 · Cited by 8
Talus, A., Alipour, Y., Norling, R., & Henderson, P. (2016) · Materials and Corrosion · doi:10.1002/maco.201508693 · Cited by 7
Effect of High-Temperature Corrosion on the Service Life of P91 Piping in Biomass Co-firing
O’Hagan, C. P., Barrett, R. A., Leen, S. B., & Monaghan, R. F. D. (2016) · Journal of Pressure Vessel Technology · doi:10.1115/1.4032648 · Cited by 6
Laboratory studies on the ageing behaviour of waste incineration superheater ash deposits
Balint, R., Niemi, J., Hayashi, S., & Lehmusto, J. (2025) · Energy · doi:10.1016/j.energy.2025.135359 · Cited by 7
Verma, R., & Kaushal, G. (2022) · Journal of Thermal Spray Technology · doi:10.1007/s11666-022-01445-6 · Cited by 6
Izzuddin, H., Hayashi, S., Yoneda, S., Kogin, T., Ishikawa, E., & Noguchi, M. (2020) · MATERIALS TRANSACTIONS · doi:10.2320/matertrans.mt-m2020156 · Cited by 5
Lehmusto, J., Olin, M., Viljanen, J., Kalliokoski, J., Mylläri, F., Toivonen, J., Maso, M. D., & Hupa, L. (2019) · Materials and Corrosion · doi:10.1002/maco.201910964 · Cited by 5
An experimental, theoretical, and kinetic modeling study of gas-phase sulfation of KCl
Chanpirak, A., Wu, H., Marshall, P., & Glarborg, P. (2024) · Fuel · doi:10.1016/j.fuel.2024.130974 · Cited by 7
Huang, Y., Wei, J., Huang, T., Yang, Z., Zhang, S., Zhu, Z., Fan, K., Luo, X., Li, X., Zhou, Q., et al. (2024) · International Journal of Pressure Vessels and Piping · doi:10.1016/j.ijpvp.2024.105205 · Cited by 4
Furugaki, T., Takahashi, H., & Hayashi, S. (2024) · High Temperature Corrosion of Materials · doi:10.1007/s11085-023-10184-0 · Cited by 4
Sun, Q., Yu, H., Wang, Y., Zhang, B., Han, X., Wang, X., Zhang, D., Lin, J., Yang, Y., & Wang, F. (2024) · npj Materials Degradation · doi:10.1038/s41529-024-00531-0 · Cited by 4
Liu, Z., Ning, Z., Luo, Q., Zhou, Q., & Li, N. (2020) · Materials and Corrosion · doi:10.1002/maco.202011669 · Cited by 3
Furnace Wall Corrosion in a Wood-fired Boiler
Alipour, Y. (2015) · DiVA (Digitala Vetenskapliga Arkivet) · Cited by 5
Hanif, I., Ssenteza, V., Eklund, J., Nockert, J., & Jonsson, T. (2023) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2023.07.073 · Cited by 5
Pu, J., Su, X., Zhang, X., Liu, X., Ma, D., Hu, Z., Dai, G., & Wang, X. (2026) · Fuel · doi:10.1016/j.fuel.2026.139118 · Cited by 4
Arivarasu, M., Kumar, K. G., Ramkumar, K. D., & Arivazhagan, N. (2016) · InTech eBooks · doi:10.5772/63997 · Cited by 3
Changes in chlorine content over time – Probe deposit sampling in a Finnish kraft recovery boiler
Balint, R., Engblom, M., Vainio, E., Laurén, T., Niemi, J., Rautala, J., Saarinen, T., Hupa, M. M., & Hupa, L. (2023) · Fuel · doi:10.1016/j.fuel.2023.127599 · Cited by 4
Thermal cycling of grate-link material for iron ore pelletising process
Nilsson, E. A. A., Tegman, R., & Antti, M. (2016) · Ironmaking & Steelmaking Processes Products and Applications · doi:10.1080/03019233.2016.1210404 · Cited by 3
Li, C., Yoneda, S., Kogin, T., Ishikawa, E., Murasue, S., & Hayashi, S. (2025) · High Temperature Corrosion of Materials · doi:10.1007/s11085-025-10350-6 · Cited by 2
The Long-Term Corrosion Behavior of Fecral(Si) Alloys after Breakaway Oxidation at 600 °CPreprint
Eklund, J., Persdotter, A., Ssenteza, V., et al. (2023) · SSRN Electronic Journal · doi:10.2139/ssrn.4351130 · Cited by 2
Ramos-Negrón, O. J., Salinas-Cortés, V. M., Escobar-Jiménez, R. F., & Gómez-Aguilar, J. F. (2025) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2025.151188 · Cited by 1
Metadata
- Authors
- Karlsson, S., Pettersson, J., Johansson, L. G., & Svensson, J. E.
- Affiliations
- Chalmers University of Technology (SE)
- Corresponding author
- Karlsson, S.
- Venue
- Oxidation of Metals
- Published
- 2012-04-27
- Volume
- 78
- Issue
- 1-2
- Pages
- 83-102
- ISSN
- 0030-770X (ISSN-L)
- 1573-4889
- OpenAlex
- W2019797599
- Cited by
- 118
- References
- 23
- Citations by year
- 2026: 10 · 2025: 9 · 2024: 12 · 2023: 7 · 2022: 12 · 2021: 8 · 2020: 5 · 2019: 11 · 2018: 4 · 2017: 7 · 2016: 14 · 2015: 7 · 2014: 7 · 2013: 4 · 2012: 1
- FWCI
- 10.22
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- Locations
- Oxidation of Metals (publishedVersion, cc-by)
- Chalmers Publication Library (Chalmers University of Technology) (submittedVersion)
- Chalmers Research (Chalmers University of Technology) (submittedVersion)
- Funders
- Chalmers Tekniska Högskola
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Physical Sciences › Materials Science › Materials Chemistry › Corrosion Behavior and Inhibition
- Keywords
- high-temperature corrosion, 304L stainless steel, sodium chloride, KCl, calcium chloride, chromium depletion, spinel oxides, calcium chromate, calcium oxide, Ca2Fe2O5, water vapor oxidation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-09-30, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-09-30 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.