The DOI matches its Crossref record; 17 of the 17 references it cites were found in a registry or an index; 3 of the 4 sources its claims cite were checked for support.
The Impact of HCl on Alkali-Induced Corrosion of Stainless Steels/FeCrAl Alloy at 600 °C: The Story After Breakaway
Open accessPublished version of a preprint
Abstract
The impact of Cl on alkali-induced high-temperature corrosion of stainless steels/FeCrAl alloys after breakaway oxidation was investigated in a simulated biomass- and waste-fired boiler environment at 600 °C. For this investigation, three alloys were exposed to low Cl load environment (H 2 O+KCl) and to high Cl load (H 2 O+KCl+HCl). Post-exposure analysis showed that the stainless steel SVM12 experiences fast oxidation and forms thick double-layered Fe-rich oxide scales. The corrosion attack is further accelerated with addition of HCl for this material with the effect being more pronounced in the inward-growing scale. The FeCrAl and FeCrNi alloys exhibit slower oxidation kinetics after the breakaway corrosion compared to SVM12 in the H 2 O+KCl exposure. Furthermore, in contrast with SVM12, the addition of HCl did not accelerate the corrosion attack on these alloys. It is argued that the properties of the secondary oxide layer formed after breakaway corrosion are important in the continued corrosion resistance against chlorine-induced corrosion attack. Especially, the Cr content in the inner scales is suggested to be important in corrosion mitigation.
Overview
CoChat Summary
TL;DR
At 600 °C in simulated biomass/waste-fired boiler conditions, all three alloys underwent breakaway within 4 h; added HCl accelerated corrosion only for the low-alloy SVM12, mainly by thickening the inward-growing scale, while APMT and 27Cr33Ni3Mo retained slower kinetics and Cr-rich inner scales. The authors argue that the properties of the secondary oxide layer after breakaway, especially Cr content in the inner scales, are important for continued resistance to chlorine-induced attack.
Key findings
- All alloys broke away after 4 h in H₂O+KCl at 600 °C, with calculated oxide thicknesses of at least 5 µm (0.8 mg/cm²) for alloy 27Cr33Ni3Mo, about 6 µm (0.9 mg/cm²) for APMT, and about 18 µm (2.9 mg/cm²) for SVM12.
- After breakaway (4–168 h), mass gain increased by 7.6 mg/cm² for SVM12, 4.1 mg/cm² for APMT, and 2.6 mg/cm² for alloy 27Cr33Ni3Mo; SVM12’s mass gain was about 3 times greater than alloy 27Cr33Ni3Mo.
- At 168 h, SVM12 reached 2.8 mg/cm² in H₂O (about 63 µm maximum oxide thickness), 10.5 mg/cm² in H₂O+KCl (93 µm), and 16 mg/cm² in H₂O+KCl+HCl (123 µm); its inward-growing scale doubled in thickness with HCl compared with H₂O+KCl.
- APMT and alloy 27Cr33Ni3Mo showed much lower mass gains and similar mass gain/oxide thickness in H₂O+KCl+HCl compared with H₂O+KCl; APMT formed a 34-µm scale in H₂O+KCl and a slightly thinner ∼25-µm scale in H₂O+KCl+HCl, while alloy 27Cr33Ni3Mo formed ∼9-µm scales in both. HCl hindered K₂CrO₄ formation and stabilized KCl on the surface, with Cr enrichment in the inner scales.
Methods
- Three alloys were studied: SVM12 (martensitic stainless steel), Kanthal® APMT (FeCrAl alloy), and alloy 27Cr33Ni3Mo (austenitic stainless steel), with sample dimensions 20 × 10 × 2 mm.
- Isothermal exposures were performed at 600 °C for 168 h in three environments: 5% O₂ + 20% H₂O + N₂ balance; the same plus 2 mg/cm² KCl pre-deposited on samples and KCl(s) upstream; and the same plus 500 ppm HCl(g). A separate 4-h exposure in H₂O+KCl assessed breakaway onset.
- Characterization used gravimetric mass gain and SEM/EDX on broad ion beam cross sections; samples were gold-sputtered, cut/polished, and BIB-milled at 8 kV for 6 h, with SEM imaging at 10 kV and chemical analysis at 20 kV.
Limitations
- The paper does not state an explicit limitations section.
- The authors note that the exact role of chlorine in changing diffusion properties remains unclear, despite attempts using 3D-FIB and TEM in other work.
- Evident from the text: the study is limited to three alloys, a laboratory-simulated environment, and a maximum exposure time of 168 h, with mechanistic conclusions based mainly on SEM/EDX cross-sectional analysis.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
3 Valid · 0 Not valid · 0 Not checked · 32 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“This improved corrosion resistance is attributed to high contents of alloying elements such as Cr, Al and Ni in the alloys (see compositions in Table1) which enables the formation of more protective Cr-rich inward-growing scales”
What the sources say
- Partly supportedcites [4] A. Persdotter, et al., Corrosion Science 177, 2020 (108961). sourceExperimental — accuracy not yet measured
The Chemical composition section reports that slow-growing FeCrAl model alloys had Cr-rich inward-growing scales and suggests that scale composition contributes to secondary corrosion protection. But Table 1 lists model alloys, not APMT or 27Cr33Ni3Mo; the paper does not establish this explanation for those two alloys. It also presents the role of inward-growing scale composition as a suggestion rather than a demonstrated cause. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The results indicate that the presence of Cl in the inner scale changes the diffusion properties of elements (e.g., oxygen) through the scale, which was also suggested in [16].”
What the sources say
- Partly supportedcites [16] J. Phother-Simon, et al., Fuel 357, 2024 (130012). sourceExperimental — accuracy not yet measured
Our copy supports the two component facts separately: Cl is indeed found inside the inner/inward-growing scale (3.1.2, p. 4: SEM-EDX shows chlorine within the inward-growing oxide and preferentially at the metal/oxide interface; 3.4.2, p. 8: TEM line scan of the Inconel 625 internal oxidation zone with Cl 0–15 at.%) and the paper discusses transport through the scale in Cl-containing exposures (Introduction, p. 2 and 4.2, pp. 10–11: cyclic gaseous transport of Cl2/MeClx via cracks and pores, reliant on an oxygen partial-pressure gradient over the scale; 4.2, p. 11: inward diffusion of Cl as Cl-). However, no passage states that the presence of Cl in the inner scale changes the diffusion properties of elements such as oxygen through the scale; on the contrary, the authors question the gaseous-transport explanation (O2 vs Cl2 molecular sizes, gas osmosis after A.G. Guy [43]) and attribute the crack-promoting/less-adherent-scale effect to another work [19]. So the specific 'changed diffusion properties of oxygen' element attributed to this source is not in it. (LLM, conf=0.68)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Thus, the mass gain of SVM12 is about 3 times greater compared to Alloy 27Cr33Ni3Mo after breakaway corrosion, i.e., in the secondary corrosion regime.”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“When exposed to H 2 O+KCl+HCl, the mass gain and oxide thickness was similar compared to the corresponding exposure in H2O+KCl.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In the presence of H 2 O+KCl, both the outward- and inward-growing scale increase in thickness relative to the H 2 O only environment.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
7 more claims
Create a free account to see all 35 claims and every source verdict.
- It may state two separate claims as one. 21
- The quote only partly states this claim. 4
Citations
Cites
Grabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Ma, W., Wenga, T., Frandsen, F. J., Yan, B., & Chen, G. (2020) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2019.100789 · Cited by 275
KCl Induced Corrosion of a 304-type Austenitic Stainless Steel at 600°C; The Role of Potassium
Pettersson, J., Asteman, H., Svensson, J. E., & Johansson, L. G. (2005) · Oxidation of Metals · doi:10.1007/s11085-005-5704-3 · Cited by 182
Jonsson, T., Karlsson, S., Hooshyar, H., Sattari, M., Liske, J., Svensson, J.-E., & Johansson, L.-G. (2016) · Oxidation of Metals · doi:10.1007/s11085-016-9610-7 · Cited by 103
Self-citationOxidation in Steam and Steam/Hydrogen Environments
Quadakkers, W. J., & Zurek, J. (2009) · Elsevier eBooks · doi:10.1016/b978-044452787-5.00022-6 · Cited by 90
Initial Stages of the HCl-Induced High-Temperature Corrosion of Alloy 310
Folkeson, N., Johansson, L.-G., & Svensson, J.-E. (2007) · Journal of The Electrochemical Society · doi:10.1149/1.2754174 · Cited by 66
Oxidation of Fe–10Cr in O2 and in O2+H2O environment at 600°C: A microstructural investigation
Jonsson, T., Pujilaksono, B., Heidari, H., Liu, F., Svensson, J.-E., Halvarsson, M., & Johansson, L.-G. (2013) · Corrosion Science · doi:10.1016/j.corsci.2013.06.016 · Cited by 64
Self-citationEklund, J., Jönsson, B., Persdotter, A., Liske, J., Svensson, J.-E., & Jonsson, T. (2018) · Corrosion Science · doi:10.1016/j.corsci.2018.09.004 · Cited by 55
Self-citationIsraelsson, N., Unocic, K. A., Hellström, K., Jonsson, T., Norell, M., Svensson, J.-E., & Johansson, L.-G. (2015) · Oxidation of Metals · doi:10.1007/s11085-015-9546-3 · Cited by 54
Self-citationPersdotter, A., Eklund, J., Liske, J., & Jonsson, T. (2020) · Corrosion Science · doi:10.1016/j.corsci.2020.108961 · Cited by 44
Self-citation
Cited by
Zhao, Z., Yao, X., Xu, K., & Li, J. (2026) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2026.123322 · Cited by 2
Fan, Z.-Y., Zhang, R.-Y., Wang, Y.-Y., Zhang, T. A., Wang, L., Wang, K., Zhang, R., Xin-Xin, Z., Wang, X.-J., & LI, J. Q. (2026) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2026.07.018
Particulate removal in high-temperature syngas purification
Nazari, M. A., & Haydary, J. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.139391
Metadata
- Authors
- Ssenteza, V., Jonsson, T., Nockert, J., & Liske, J.
- Affiliations
- Chalmers University of Technology (SE)
- Kanthal (Sweden) (SE)
- Corresponding author
- Ssenteza, Vicent
- Jonsson, Torbjörn
- Nockert, Johanna
- Liske, Jesper
- Venue
- High Temperature Corrosion of Materials
- Published
- 2024-07-22
- Volume
- 101
- Issue
- 5
- Pages
- 1067-1076
- ISSN
- 2731-8397 (ISSN-L)
- 2731-8400
- OpenAlex
- W4400874145
- Semantic Scholar
- f2521c93ea5f1d20058815942a472ba006a50027
- Cited by
- 5
- References
- 17
- Citations by year
- 2026: 4 · 2025: 1
- FWCI
- 0.86
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- High Temperature Corrosion of Materials (publishedVersion, cc-by)
- Research Square (acceptedVersion, cc-by)
- Chalmers Research (Chalmers University of Technology) (submittedVersion, other-oa)
- Funders
- Horizon 2020 Framework Programme (815147)
- Chalmers University of Technology
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Engineering › Mechanical Engineering › High Temperature Alloys and Creep
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Keywords
- hydrogen chloride, breakaway oxidation, stainless steel, FeCrAl alloys, Fe-Cr-Ni alloys, potassium chloride, chlorine-induced corrosion, chromium content, corrosion protection
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The Impact of HCl on Alkali-Induced Corrosion of Stainless Steels/FeCrAl Alloy at 600 °C: The Story After Breakaway. https://app.cochat.ai/papers/10.1007/s11085-024-10265-8
- The paper
- Ssenteza, V., Jonsson, T., Nockert, J., & Liske, J. (2024). The Impact of HCl on Alkali-Induced Corrosion of Stainless Steels/FeCrAl Alloy at 600 °C: The Story After Breakaway. High Temperature Corrosion of Materials. https://doi.org/10.1007/s11085-024-10265-8
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.