CoChat

Comparative Stability Studies of Poly(2-methyl-2-oxazoline) and Poly(ethylene glycol) Brush Coatings

Open access

The DOI matches its Crossref record; 82 of the 83 references it cites were found in a registry or an index.

Abstract

Non-fouling surfaces that resist non-specific adsorption of proteins, bacteria, and higher organisms are of particular interest in diverse applications ranging from marine coatings to diagnostic devices and biomedical implants. Poly(ethylene glycol) (PEG) is the most frequently used polymer to impart surfaces with such non-fouling properties. Nevertheless, limitations in PEG stability have stimulated research on alternative polymers that are potentially more stable than PEG. Among them, we previously investigated poly(2-methyl-2-oxazoline) (PMOXA), a peptidomimetic polymer, and found that PMOXA shows excellent anti-fouling properties. Here, we compare the stability of films self-assembled from graft copolymers exposing a dense brush layer of PEG and PMOXA side chains, respectively, in physiological and oxidative media. Before media exposure both film types prevented the adsorption of full serum proteins to below the detection limit of optical waveguide in situ measurements. Before and after media exposure for up to 2 weeks, the total film thickness, chemical composition, and total adsorbed mass of the films were quantified using variable angle spectroscopic ellipsometry (VASE), X-ray photoelectron spectroscopy (XPS), and optical waveguide lightmode spectroscopy (OWLS), respectively. We found (i) that PMOXA graft copolymer films were significantly more stable than PEG graft copolymer films and kept their protein-repellent properties under all investigated conditions and (ii) that film degradation was due to side chain degradation rather than due to copolymer desorption.

Overview

Integrity signals

Registry

Crossref · 10.1007/s13758-011-0001-y

Cites

82 of 82 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Figures

Fig. 1 a Comparison of mechanical testing single fiber properties for PCL with Voce hardening law. b Example of tube model subjected to compressive loading in ANSYS. c Simulated response to torsional loading as winding angle is varied
Fig. 1 a Comparison of mechanical testing single fiber properties for PCL with Voce hardening law. b Example of tube model subjected to compressive loading in ANSYS. c Simulated response to torsional loading as winding angle is variedCC BY · PubMed Central
Fig. 2 a Variation in pore architecture and quantity with winding angle for ten fiber pairs. Increase in number of fiber crossover points (b) and corresponding decrease in average pore size (c) with increasing number of fibers and winding angle. d Variation of total porosity with number of fiber pairs and winding angle
Fig. 2 a Variation in pore architecture and quantity with winding angle for ten fiber pairs. Increase in number of fiber crossover points (b) and corresponding decrease in average pore size (c) with increasing number of fibers and winding angle. d Variation of total porosity with number of fiber pairs and winding angleCC BY · PubMed Central
Fig. 3 Comparison of simulated response to uniaxial tensile and compressive loading for tubes comprised of ten a unbonded and b bonded fiber pairs with varying winding angle. SEM images showing interwoven melt electrospun fibers with c minimal evidence of bonding due to melt fusion at the crossover points, and d evidence of fusion between fibers. All scale bars 100 μm
Fig. 3 Comparison of simulated response to uniaxial tensile and compressive loading for tubes comprised of ten a unbonded and b bonded fiber pairs with varying winding angle. SEM images showing interwoven melt electrospun fibers with c minimal evidence of bonding due to melt fusion at the crossover points, and d evidence of fusion between fibers. All scale bars 100 μmCC BY · PubMed Central
Fig. 4 a Schematic illustration showing fabrication of a porous tube by combining melt electrospinning with direct writing by using a rotating collector on a translating stage. Due to the characteristic lag effect of the melt electrospinning jet, the effective translation of the jet (Te) which corresponds to the tube height is shorter than the actual programmed translation of the stage (Tp). b Porous tube fabricated by combining melt electrospinning of PCL with direct writing. c SEM image showing smooth uniform fibers interwoven and oriented at 60° to the central axis of the tube
Fig. 4 a Schematic illustration showing fabrication of a porous tube by combining melt electrospinning with direct writing by using a rotating collector on a translating stage. Due to the characteristic lag effect of the melt electrospinning jet, the effective translation of the jet (Te) which corresponds to the tube height is shorter than the actual programmed translation of the stage (Tp). b Porous tube fabricated by combining melt electrospinning of PCL with direct writing. c SEM image showing smooth uniform fibers interwoven and oriented at 60° to the central axis of the tubeCC BY · PubMed Central
Fig. 5 Front and oblique μCT images of a 3 mm central section of melt electrospun tubes shows tubes are comprised of ten fibrous layers and the pore size decreases as the winding angle is increased from a 30° to b 45° and c 60°. All scale bars 1 mm
Fig. 5 Front and oblique μCT images of a 3 mm central section of melt electrospun tubes shows tubes are comprised of ten fibrous layers and the pore size decreases as the winding angle is increased from a 30° to b 45° and c 60°. All scale bars 1 mmCC BY · PubMed Central
Fig. 6 Mechanical testing of melt electrospun wound tubes in a tension and b in compression (where the onset of buckling is shown). Response of tubes to mechanical loading in c tension and d compression. Mean values and standard error bars are shown (n = 5)
Fig. 6 Mechanical testing of melt electrospun wound tubes in a tension and b in compression (where the onset of buckling is shown). Response of tubes to mechanical loading in c tension and d compression. Mean values and standard error bars are shown (n = 5)CC BY · PubMed Central
Fig. 7 Culture of hOBs on CaP coated electrospun PCL tubular scaffolds. a Optical image showing fibers with winding angle of 45° prior to CaP coating. b SEM image showing the coated PCL meshes prior to cell seeding. An SEM image taken at higher resolution (inset 25 × 25 μm) reveals the microstructure of the biomimetic coating. c CLSM 3D projection of hOBs cultured on the scaffold for 2 weeks. Cells were fixed and stained for f-actin (red) and nuclei (blue). An overlay of the fluorescent and transmission light microscopy image is shown. d LSM 3D projection taken at higher magnification [same conditions as in c]. e SEM image showing hOBs after 2 weeks of culture on the scaffold. Arrows in d and e indicate fiber crossovers where hOBs start to span neighbouring fibers. f Live/dead assay by using FDA/PI staining showed that >90% of the hOBs were alive after 2 weeks of culture
Fig. 7 Culture of hOBs on CaP coated electrospun PCL tubular scaffolds. a Optical image showing fibers with winding angle of 45° prior to CaP coating. b SEM image showing the coated PCL meshes prior to cell seeding. An SEM image taken at higher resolution (inset 25 × 25 μm) reveals the microstructure of the biomimetic coating. c CLSM 3D projection of hOBs cultured on the scaffold for 2 weeks. Cells were fixed and stained for f-actin (red) and nuclei (blue). An overlay of the fluorescent and transmission light microscopy image is shown. d LSM 3D projection taken at higher magnification [same conditions as in c]. e SEM image showing hOBs after 2 weeks of culture on the scaffold. Arrows in d and e indicate fiber crossovers where hOBs start to span neighbouring fibers. f Live/dead assay by using FDA/PI staining showed that >90% of the hOBs were alive after 2 weeks of cultureCC BY · PubMed Central
Fig. 8 Culture of mOBs on melt electrospun PCL fibers taken from a tube with a winding angle of 30°. mOBs initially showed good attachment and then proliferated over a culture period of 4 weeks. a After 4 weeks of culture a 2 mm biopsy punch was used to harvest the specimen shown in b–d. SEM showed that the mOBs formed a mineralized ECM not only on the scaffold fibers but also inside and across the pore architecture (b and c). d CLSM revealed by using DAPI/Phalloidin staining alignment of mOBs along the fiber axis
Fig. 8 Culture of mOBs on melt electrospun PCL fibers taken from a tube with a winding angle of 30°. mOBs initially showed good attachment and then proliferated over a culture period of 4 weeks. a After 4 weeks of culture a 2 mm biopsy punch was used to harvest the specimen shown in b–d. SEM showed that the mOBs formed a mineralized ECM not only on the scaffold fibers but also inside and across the pore architecture (b and c). d CLSM revealed by using DAPI/Phalloidin staining alignment of mOBs along the fiber axisCC BY · PubMed Central
Fig. 9 Met-5A cells were seeded on PCL meshes at a density of 2 × 105 cells in 40 μL. Scaffold/cell constructs were imaged every 2 weeks performing cell viability and imaging analyses using CLSM (a–c) and SEM (d). a Over the culture period a cell viability of greater than 90% was determined by live/dead staining. b Maximal projections of CLSM images (inset scale bars 100 μm) revealed an ongoing cell/ECM sheet formation covering more than 75% of the pore space indicated by (c) 3D reconstructions. d SEM revealed the morphology of Met-5A cells, where sheet formation started on day 14 and continued up to day 28
Fig. 9 Met-5A cells were seeded on PCL meshes at a density of 2 × 105 cells in 40 μL. Scaffold/cell constructs were imaged every 2 weeks performing cell viability and imaging analyses using CLSM (a–c) and SEM (d). a Over the culture period a cell viability of greater than 90% was determined by live/dead staining. b Maximal projections of CLSM images (inset scale bars 100 μm) revealed an ongoing cell/ECM sheet formation covering more than 75% of the pore space indicated by (c) 3D reconstructions. d SEM revealed the morphology of Met-5A cells, where sheet formation started on day 14 and continued up to day 28CC BY · PubMed Central

Verification

Claims the paper makes

We couldn’t retrieve this paper’s full text, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Citations

Cites

Show all 82 references

Research works printed but not linked: 2

  1. 1960, J Polym Sci Part A Polym Chem, 46, 51
  2. 2001, J Biomed Mater Res, 56, 324, 10.1002/1097-4636(20010905)56:3<324::AID-JBM1100>3.0.CO;2-P · doi:10.1002/1097-4636(20010905)56:3<324::aid-jbm1100>3.0.co;2-p

Cited by

See all 251

Metadata

Authors
Pidhatika, B., Rodenstein, M., Chen, Y., Rakhmatullina, E., Mühlebach, A., Acikgöz, C., Textor, M., & Konradi, R.
Affiliations
  • ETH Zurich (CH)
  • Hong Kong University of Science and Technology (HK)
  • University of Bern (CH)
  • BASF (Switzerland) (CH)
Venue
Biointerphases
Published
2012-02-09
Volume
7
Issue
1
Pages
1-1
ISSN
  • 1559-4106 (ISSN-L)
  • 1934-8630
OpenAlex
W2058340976
Cited by
251
References
83
Citations by year
2026: 8 · 2025: 10 · 2024: 12 · 2023: 9 · 2022: 7 · 2021: 16 · 2020: 17 · 2019: 27 · 2018: 23 · 2017: 19 · 2016: 24 · 2015: 26 · 2014: 28 · 2013: 15 · 2012: 10
FWCI
11.16
Type
journal article
Language
en
Open access
Licence
Locations
  • Biointerphases (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • Rare & Special e-Zone (The Hong Kong University of Science and Technology) (submittedVersion)
  • Bern Open Repository and Information System (University of Bern) (submittedVersion)
Funders
  • Schweizerischer Nationalfonds zur Förderung der Wissenschaftlichen Forschung
  • Division of Materials Research
Topics
  • Physical Sciences › Materials Science › Surfaces, Coatings and Films › Polymer Surface Interaction Studies
  • Physical Sciences › Engineering › Ocean Engineering › Marine Biology and Environmental Chemistry
  • Physical Sciences › Chemistry › Organic Chemistry › Advanced Polymer Synthesis and Characterization
Keywords
poly(2-methyl-2-oxazoline), polyethylene glycol, brush coating, graft copolymers, non-fouling surfaces, antifouling, protein adsorption, film stability, side chain degradation, physiological media
MeSH terms
Adsorption, Blood Proteins, Polyamines, Polyethylene Glycols, Coated Materials, Biocompatible

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Comparative Stability Studies of Poly(2-methyl-2-oxazoline) and Poly(ethylene glycol) Brush Coatings. https://app.cochat.ai/papers/10.1007/s13758-011-0001-y
The paper
Pidhatika, B., Rodenstein, M., Chen, Y., Rakhmatullina, E., Mühlebach, A., Acikgöz, C., Textor, M., & Konradi, R. (2012). Comparative Stability Studies of Poly(2-methyl-2-oxazoline) and Poly(ethylene glycol) Brush Coatings. Biointerphases. https://doi.org/10.1007/s13758-011-0001-y

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.