The DOI matches its Crossref record; 121 of the 121 references it cites were found in a registry or an index; 21 of the 163 sources its claims cite were checked for support.
Hydration lubrication
Open accessAbstract
The hydration lubrication paradigm, whereby hydration layers are both strongly held by the charges they surround, and so can support large pressures without being squeezed out, and at the same time remain very rapidly relaxing and so have a fluid response to shear, provides a framework for understanding, controlling, and designing very efficient boundary lubrication systems in aqueous and biological media. This review discusses the properties of confined water, which—unlike organic solvents—retains its fluidity down to molecularly thin films. It then describes lubrication by hydrated ions trapped between charged surfaces, and by other hydrated boundary species including charged and zwitterionic polymer brushes, surfactant monolayers, liposomes, and biological macromolecules implicated in synovial joint lubrication. Finally, challenges and prospects for future development of this new boundary lubrication approach are considered.
Overview
CoChat Summary
## TL;DR
This review argues that hydration lubrication is a general boundary-lubrication mechanism in aqueous media: tightly held hydration layers can sustain high normal loads while still responding fluidly to shear. It surveys evidence from confined water, hydrated ions, charged/zwitterionic polymer brushes, surfactants, liposomes, and biological joints.
## Key findings
- Water confined to films thinner than about 3 nm retained close to bulk-like fluidity; the paper states that the effective viscosity in such films was within a factor of 3 of bulk water viscosity, about 0.001 Pa·s.
- In SFB experiments on trapped hydrated ions, friction in the hydration-repulsion regime was extremely low: the effective friction coefficient was estimated to be no greater than ≈ 0.0002, and the review gives an upper-limit estimate of ≈ 0.0003 from a simple model.
- Hydrated cations between charged surfaces could support large pressures; the paper estimates a crude maximal hydration-repulsion pressure of about 10^9 N/m^2 (1 GPa), while noting that measured repulsion in the cited experiments extended to about 0.3 MPa and later work to about 10 MPa.
- Zwitterionic pMPC brush layers showed very low friction in water: the paper reports friction coefficients as low as 0.0004 at pressures as high as about 8 MPa, and liposome-coated surfaces reached friction coefficients as low as 2 × 10^-5 at mean pressures over 10 MPa.
- In cartilage-related measurements, HA-coated surfaces gave a friction coefficient of about 0.3, HA/aggrecan complexes about 0.01 up to roughly 10 atm, and lubricin-bearing surfaces about 0.02 up to about 5–10 atm; the paper says these are still higher than the friction reported for healthy joints, around 0.001.
## Methods
- Review article synthesizing previously published surface force balance (SFB), tribology, and biological lubrication studies rather than presenting a new standalone experiment.
- Discusses model systems including mica–mica, mica–gold, charged polymer brushes, surfactant monolayers, phospholipid liposomes, and cartilage-related macromolecules in aqueous media.
- Interprets force–distance and shear-force measurements, using concepts such as hydration repulsion, hydration shell relaxation, and simple estimates based on load, area, and viscosity to infer friction coefficients and pressure scales.
## Limitations
- The paper explicitly says several key issues remain unresolved, including the precise mechanism of hydration lubrication, whether hydration shells respond Newtonianly to shear, the ultimate pressures at which the mechanism applies, and how to rank charged groups by hydration-lubrication efficiency.
- The text notes that some estimates are crude or upper limits, especially the 1 GPa pressure estimate for hydration repulsion and the friction estimates derived from simple shear-viscosity arguments.
- Evident from the text: much of the evidence comes from idealized SFB experiments on atomically smooth mica or similarly controlled surfaces, and the paper explicitly cautions that other dissipation modes and less ideal surfaces may limit how representative these results are for real soft or biological interfaces.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
20 Valid · 0 Not valid · 76 Not checked · 57 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“In contrast, for the case of water, almost uniquely, the liquid phase is denser than the solid phase (which is why ice floats). Thus the densification of a thin confined water film acts to suppress its tendency to solidify [54], which is why water in films of thickness down to a single monolayer or so retains close to its bulk fluidity.”
What the sources say
- Supportedcites [54] Jagla E A. Boundary lubrication properties of materials with expansive freezing. Phys Rev Lett88: 245504 (2002) source
Our copy states the claim's substance in its own vocabulary: the density inversion is carried by the paper's central concept of 'expansive freezing' (Intro, p. 1: 'the good lubrication properties of water can be associated to its expansive freezing'), and the consequence — compression/densification suppressing solidification — is stated both in Results (p. 2: 'The film remains in a liquid-like state as F s increases ... particles ... can go closer ... upon a reduction of d , without generating a higher degree of order') and in the Summary (p. 3: 'materials with expansive freezing ... do not show a strong tendency to solidify as they are squeezed'). The citing sentence's follow-on point about near-bulk fluidity in molecular-thickness films is also in the paper (p. 3, viscosity 'no more than a few times the bulk value'). The only element our copy does not carry is the 'almost uniquely' qualifier — the paper calls water a 'noteworthy exception' to the boundary-lubrication rule rather than asserting rarity of the density anomaly — but that is framing, not the attributed mechanism. (LLM, conf=0.85)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Chen et al. [80] measured the friction coefficients between sliding surfaces bearing such brushes [43]. The results are summarized in Fig. 12, which shows that the friction coefficients in pure water remain as low as 0.0004 even at pressures as high as ca. 8 MPa (80 atm).”
What the sources say
- Not checked yetcites [80] Chen M, Briscoe W H, Cohen H, Armes S P, Klein J. Polyzwitterionic brushes: extreme lubrication by design. European Polymer Journal47: 511–523 (2011) source
Checked before — its earlier verdict is held back until a new check runs.
- Supportedcites [43] Chen M, Briscoe W H, Armes S P, Klein J. Lubrication at physiological pressures by polyzwitterionic brushes. Science323: 1698–1701 (2009) source
The Figure 4 caption (Figure Captions) gives a friction coefficient of 0.00043 for pMPC-brush-coated surfaces sliding in water. The Published paper reports measurements up to 7.5 MPa (75 atmospheres), consistent with the citing sentence’s approximate 8 MPa (80 atmospheres). (LLM, conf=0.92)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not checked yet
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Raviv et al. [44, 74] studied the shear forces between charged polymer brushes in water, and discovered that such brushes provided boundary lubrication that was significantly more efficient than neutral polymer brushes.”
What the sources say
- Supportedcites [44] Raviv U, Giasson S, Kampf N, Gohy J F, Jérôme R, Klein J. Lubrication by charged polymers. Nature425: 163–165 (2003) source
The abstract says charged polymer brushes in water provide superior lubrication to other polymeric surfactants. The Fig. 3 comparison (indexed under Abstract) specifically shows that friction remains extremely low for charged brushes at high compression, while it rises for neutral brushes in water. (LLM, conf=0.93)
- Not checked — no full text of the sourcecites [74] Raviv U, Giasson S, Gohy J-F, Jerome R, Klein J. Normal and frictional forces between surfaces bearing polyelectrolyte brushes. Langmuir24: 8678–8687 (2008) source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“To overcome this, Chen et al. [79] adopted a different strategy -covalently growing polymers from the substrate to produce a much more strongly attached brush, consisting of poly[2-(Methacryloyloxy)ethyl PhosphoCholine], pMPC, chains [43, 79, 80].”
What the sources say
- Not checked — no full text of the sourcecites [79] Chen M, Briscoe W H, Armes S P, Cohen H, Klein J. Robust, biomimetic polymer brush layers grown directly from a planar mica surface. ChemPhysChem8: 1303–1306 (2007) source
- Supportedcites [43] Chen M, Briscoe W H, Armes S P, Klein J. Lubrication at physiological pressures by polyzwitterionic brushes. Science323: 1698–1701 (2009) source
The Published paper describes pMPC brushes grown from macroinitiator-coated mica surfaces and identifies the process as grafting-from growth. It also says the grafted-from chains have stronger attachment, while note 15 states that the chains are covalently attached to initiation sites. Page numbers are not provided in our copy. (LLM, conf=0.94)
- Supportedcites [80] Chen M, Briscoe W H, Cohen H, Armes S P, Klein J. Polyzwitterionic brushes: extreme lubrication by design. European Polymer Journal47: 511–523 (2011) source
The Introduction (p. ~1, passage 3) states that 'grafting from' grows polymer from surface-bound initiators 'monomer by monomer via covalent bonding', which 'can lead to much stronger anchoring', and that in this study pMPC (poly(2-(methacryloyloxy)ethyl phosphorylcholine)) brushes 'have been directly grown from planar mica pre-coated with macroinitiator using atom transfer radical polymerisation'. Section 2.4 (passages 1 and 4) details the covalent surface-initiated ATRP growth of pMPC from macroinitiator-coated mica, and Section 3.1 (passage 2) confirms the resulting grafted layer by XPS. This matches the attributed claim exactly. (LLM, conf=0.92)
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
Every source the paper cites for this claim was checked and supports it.
In the paper
“At physiologically high salt concentrations up to 0.1 M salt, the friction coefficient with the pMPC brushes was found [43] to increase slightly (to around 0.001 - 0.002):”
What the sources say
- Supportedcites [43] Chen M, Briscoe W H, Armes S P, Klein J. Lubrication at physiological pressures by polyzwitterionic brushes. Science323: 1698–1701 (2009) source
The Published paper reports that the friction coefficient of pMPC brushes increases slightly with salt concentration while remaining around (1.5 ± 1) × 10⁻³. It describes measurements at approximately 0.1 M NaNO₃, consistent with the citing sentence’s approximate range of 0.001–0.002. (LLM, conf=0.92)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
82 more claims · 7 with their cited sources checked
Create a free account to see all 153 claims and to verify the 5 references still open.
- It may state two separate claims as one. 56
- Probably not a substantial claim. 16
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“SFB studies show a general tendency for metal ions to increase the lubrication of water films confined between negatively charged mica surfaces, at least for ionic concentrations in the order of 100 mM NaCl.39,42,49”
From Lubricating properties of single metal ions at interfaces (2018) · cites this paper as [49]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“SFB studies indicate that ultrapure water remains mostly fluid even when confined to gaps <3.5 nm, resulting in a 3-5 fold increase in viscosity.22,28,42,49”
From Lubricating properties of single metal ions at interfaces (2018) · cites this paper as [49]
Experimental — accuracy not yet measured
Citations
Cites
(1999) · Choice Reviews Online · doi:10.5860/choice.37-0940 · Cited by 14,314
New-Concept Chemotherapy by Nanoparticles of Biodegradable Polymers: Where Are We Now?
Feng, S.-S. (2006) · Nanomedicine · doi:10.2217/17435889.1.3.297 · Cited by 1,951
Israelachvili, J. N., & Adams, G. E. (1978) · Journal of the Chemical Society, Faraday Transactions 1: Physical Chemistry in Condensed Phases · doi:10.1039/f19787400975 · Cited by 1,812
Colloids and Surfaces A: Physicochemical and Engineering Aspects
Shibatani, M., Asakawa, T., Enomae, T., & Isogai, A. (2008) · Cited by 1,256
Tethered chains in polymer microstructures
Halperin, A., Tirrell, M., & Lodge, T. P. (2006) · Advances in Polymer Science · doi:10.1007/bfb0051635 · Cited by 1,139
The Friction and Lubrication of Solids
Bowden, F. P., & Tabor, D. (2001) · doi:10.1093/oso/9780198507772.001.0001 · Cited by 1,059
Pashley, R. M. (1981) · Journal of Colloid and Interface Science · doi:10.1016/0021-9797(81)90348-9 · Cited by 958
Derjaguin, B. V., Churaev, N. V., & Muller, V. M. (1987) · Springer eBooks · doi:10.1007/978-1-4757-6639-4 · Cited by 942
Lubrication by charged polymers
Raviv, U., Giasson, S., Kampf, N., Gohy, J.-F., Jérôme, R., & Klein, J. (2003) · Nature · doi:10.1038/nature01970 · Cited by 910
Self-citationCVI.A molecular theory of friction
Tomlinson, G. A. (1929) · The London, Edinburgh, and Dublin Philosophical Magazine and Journal of Science · doi:10.1080/14786440608564819 · Cited by 905
Research works printed but not linked: 14
- Dowson D. History of Tribology. London: Longmans, 1979.
- Bhushan B. Modern Tribology Handbook, Vols. 1 and 2. Boca Raton: CRC Press, 2001.
- Hardy W, Bircumshaw I. Boundary lubrication: Plane surfaces and the limitations of Amontons Law. In Proc. Roy. Soc., London, UK, 1925: 1–27.
- Hardy W B. Collected Works. Cambridge: Cambridge University Press, 1936.
- Bowden F P, Tabor D. The Friction and Lubrication of Solids I. Oxford: Clarendon Press, 1950.
- Bowden F P, Tabor D. The Friction and Lubrication of Solids II. Oxford: Clarendon Press, 1964.
- Dowson D, Wright V, Longfield M D. Human joint lubrication. Biomed Eng4: 160–165 (1969)
- Saluja P P S. Environment of ions in aqueous solutions. Int Rev Sci Electrochemistry, Part 1, Physical Chemistry Series26: 1–51 (1976)
- Burgess J. Metal Ions in Solution. Chichester: Ellis Horwood Ltd., 1978.
- Disalvo E A, Lairion F, Martini F, Almaleck H. Water in biological membranes at interfaces: Does it play a functional role? J Argent Chem Soc92: 1–22 (2004)
- Wright V, Dowson D. Lubrication and cartilage. J Anat121: 107–118 (1976)
- Wright V. Lubrication and wear in joints. London: Sector Publishing, 1969.
- Maroudas A. Hyaluronic acid films. In: lubrication and wear in living and artificial human joints. Proc Inst Mech Eng181:122–124 (1967)
- Bartlett P N. General discussion. Faraday Discuss156: 203–222 (2012)
Cited by
Mechanical properties of nanoparticles: basics and applications
Guo, D., Xie, G., & Luo, J. (2014) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/47/1/013001 · Cited by 723
Recent Progress in Cartilage Lubrication
Lin, W., & Klein, J. (2021) · Advanced Materials · doi:10.1002/adma.202005513 · Cited by 446
Self-citationLubrication of Articular Cartilage
Jahn, S., Seror, J., & Klein, J. (2016) · Annual Review of Biomedical Engineering · doi:10.1146/annurev-bioeng-081514-123305 · Cited by 406
Self-citationSupramolecular synergy in the boundary lubrication of synovial joints
Seror, J., Zhu, L., Goldberg, R., Day, A. J., & Klein, J. (2015) · Nature Communications · doi:10.1038/ncomms7497 · Cited by 355
Self-citationHan, Y., Yang, J., Zhao, W., Wang, H., Sun, Y., Chen, Y., Luo, J., Deng, L., Xu, X., Cui, W., et al. (2021) · Bioactive Materials · doi:10.1016/j.bioactmat.2021.03.022 · Cited by 308
Metadata
- Authors
- Klein, J.
- Affiliations
- Weizmann Institute of Science (IL)
- Corresponding author
- Klein, Jacob
- ORCID
- Klein, Jacob
- Venue
- Friction
- Publisher
- Tsinghua University Press
- Published
- 2013-03
- Volume
- 1
- Issue
- 1
- Pages
- 1-23
- ISSN
- 2223-7690 (ISSN-L)
- 2223-7704
- OpenAlex
- W4211157371
- Cited by
- 567
- References
- 118
- Citations by year
- 2026: 37 · 2025: 64 · 2024: 61 · 2023: 44 · 2022: 67 · 2021: 54 · 2020: 53 · 2019: 49 · 2018: 29 · 2017: 25 · 2016: 24 · 2015: 21 · 2014: 26 · 2013: 13
- FWCI
- 37.11
- Type
- journal article
- Language
- en
- Open access
- diamond
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/2.0 (tdm)
- creativecommons.org/licenses/by/2.0 (vor, 25 d)
- Locations
- Friction (publishedVersion, cc-by)
- Funders
- McCutchen Foundation
- Israel Science Foundation
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Lubricants and Their Additives
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Life Sciences › Biochemistry, Genetics and Molecular Biology › Biophysics › Chemical and Physical Studies
- Keywords
- hydration lubrication, boundary lubrication, confined water, hydration shell, charged surfaces, hydrated ions, zwitterionic polymer brushes, surfactant monolayers, liposomes, biological macromolecules, synovial joint lubrication, aqueous lubrication
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (qwen3.8-omni-flash and gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Hydration lubrication. https://app.cochat.ai/papers/10.1007/s40544-013-0001-7
- The paper
- Klein, J. (2013). Hydration lubrication. Friction. https://doi.org/10.1007/s40544-013-0001-7
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.