The DOI matches its Crossref record; 51 of the 51 references it cites were found in a registry or an index.
The effect of powder oxidation on defect formation in laser additive manufacturing
Open accessAbstract
Abstract Understanding defect formation during laser additive manufacturing (LAM) of virgin, stored, and reused powders is crucial for the production of high quality additively manufactured parts. We investigate the effects of powder oxidation on the molten pool dynamics and defect formation during LAM. We compare virgin and oxidised Invar 36 powder under overhang and layer-by-layer build conditions using in situ and operando X-ray Imaging. The oxygen content of the oxidised powder was found to be ca. 6 times greater (0.343 wt.%) than the virgin powder (0.057 wt.%). During LAM, the powder oxide is entrained into the molten pool, altering the Marangoni convection from an inward centrifugal to an outward centripetal flow. We hypothesise that the oxide promotes pore nucleation, stabilisation, and growth. We observe that spatter occurs more frequently under overhang conditions compared to layer-by-layer conditions. Droplet spatter can be formed by indirect laser-driven gas expansion and by the laser-induced metal vapour at the melt surface. Under layer-by-layer build conditions, laser re-melting reduces the pore size distribution and number density either by promoting gas release from keyholing or by inducing liquid flow, partially or completely filling pre-existing pores. We also observe that pores residing at the track surface can burst during laser re-melting, resulting in either formation of droplet spatter and an open pore or healing of the pore via Marangoni flow. This study confirms that excessive oxygen in the powder feedstock may cause defect formation in LAM.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
NIH Image to ImageJ: 25 years of image analysis
Schneider, C. A., Rasband, W. S., & Eliceiri, K. W. (2012) · Nature Methods · doi:10.1038/nmeth.2089 · Cited by 64,638
Biesinger, M. C., Payne, B. P., Grosvenor, A. P., Lau, L. W. M., Gerson, A. R., & Smart, R. S. C. (2011) · Applied Surface Science · doi:10.1016/j.apsusc.2010.10.051 · Cited by 11,640
Image denoising by sparse 3-D transform-domain collaborative filtering
Dabov, K., Foi, A., Katkovnik, V., & Egiazarian, K. (2007) · IEEE Transactions on Image Processing · doi:10.1109/tip.2007.901238 · Cited by 9,283
TrackMate: An open and extensible platform for single-particle tracking
Tinevez, J.-Y., Perry, N., Schindelin, J., Hoopes, G. M., Reynolds, G. D., Laplantine, E., Bednarek, S. Y., Shorte, S. L., & Eliceiri, K. W. (2017) · Methods · doi:10.1016/j.ymeth.2016.09.016 · Cited by 3,380
Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.02.014 · Cited by 2,766
Profex: a graphical user interface for the Rietveld refinement program BGMN
Doebelin, N., & Kleeberg, R. (2015) · Journal of Applied Crystallography · doi:10.1107/s1600576715014685 · Cited by 1,808
Olakanmi, E. O., Cochrane, R. F., & Dalgarno, K. W. (2015) · Progress in Materials Science · doi:10.1016/j.pmatsci.2015.03.002 · Cited by 1,742
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., Kamath, C., & Rubenchik, A. M. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.005 · Cited by 1,616
Steen, W. M. (1998) · Springer eBooks · doi:10.1007/978-1-4471-3609-5 · Cited by 1,547
Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
Everton, S. K., Hirsch, M., Stravroulakis, P., Leach, R. K., & Clare, A. T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.099 · Cited by 1,469
Maire, E., & Withers, P. J. (2014) · International Materials Reviews · doi:10.1179/1743280413y.0000000023 · Cited by 1,374
Self-citationReducing porosity in AlSi10Mg parts processed by selective laser melting
Aboulkhair, N. T., Everitt, N. M., Ashcroft, I., & Tuck, C. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.001 · Cited by 1,281
Qiu, C., Panwisawas, C., Ward, R., Basoalto, H., Brooks, J. W., & Attallah, M. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.06.004 · Cited by 1,041
Selective laser melting of aluminium components
Louvis, E., Fox, P., & Sutcliffe, C. J. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.019 · Cited by 933
Alloy design for aircraft engines
Pollock, T. M. (2016) · Nature Materials · doi:10.1038/nmat4709 · Cited by 931
Steen, W. M., & Mazumder, J. (2010) · Springer eBooks · doi:10.1007/978-1-84996-062-5 · Cited by 907
Qiu, C., Adkins, N. J. E., & Attallah, M. M. (2013) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.04.099 · Cited by 821
In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing
Leung, C. L. A., Marussi, S., Atwood, R. C., Towrie, M., Withers, P. J., & Lee, P. D. (2018) · Nature Communications · doi:10.1038/s41467-018-03734-7 · Cited by 817
Self-citationDenudation of metal powder layers in laser powder bed fusion processes
Matthews, M. J., Guss, G., Khairallah, S. A., Rubenchik, A. M., Depond, P. J., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.05.017 · Cited by 809
Zhao, C., Fezzaa, K., Cunningham, R. W., Wen, H., De Carlo, F., Chen, L., Rollett, A. D., & Sun, T. (2017) · Scientific Reports · doi:10.1038/s41598-017-03761-2 · Cited by 758
Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting
Kasperovich, G., & Hausmann, J. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.01.025 · Cited by 735
Harrison, N. J., Todd, I., & Mumtaz, K. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.04.035 · Cited by 690
Spierings, A. B., Herres, N., & Levy, G. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111124770 · Cited by 614
An ESCA method for determining the oxide thickness on aluminum alloys
Strohmeier, B. R. (1990) · Surface and Interface Analysis · doi:10.1002/sia.740150109 · Cited by 595
Residual Stress within Metallic Model Made by Selective Laser Melting Process
Shiomi, M., Osakada, K., Nakamura, K., Yamashita, T., & Abe, F. (2004) · CIRP Annals · doi:10.1016/s0007-8506(07)60677-5 · Cited by 591
Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg
Weingarten, C., Buchbinder, D., Pirch, N., Meiners, W., Wissenbach, K., & Poprawe, R. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.02.013 · Cited by 585
Fluid and particle dynamics in laser powder bed fusion
Bidare, P., Bitharas, I., Ward, R. M., Attallah, M. M., & Moore, A. J. (2018) · Acta Materialia · doi:10.1016/j.actamat.2017.09.051 · Cited by 555
Ly, S., Rubenchik, A. M., Khairallah, S. A., Guss, G. M., & Matthews, M. J. (2017) · Scientific Reports · doi:10.1038/s41598-017-04237-z · Cited by 521
Liu, Y., Yang, Y., Mai, S., Wang, D., & Song, C. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.08.086 · Cited by 498
Guo, Q., Zhao, C., Escano, L. I., Young, Z., Xiong, L., Fezzaa, K., Everhart, W., Brown, B., Sun, T., & Chen, L. (2018) · Acta Materialia · doi:10.1016/j.actamat.2018.03.036 · Cited by 409
Tan, J. H., Wong, W. L. E., & Dalgarno, K. W. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2017.10.011 · Cited by 407
Multiscale Modeling of Powder Bed–Based Additive Manufacturing
Markl, M., & Körner, C. (2016) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070115-032158 · Cited by 401
Fundamentals of Selective Laser Melting of alloyed steel powders
Rombouts, M., Kruth, J. P., Froyen, L., & Mercelis, P. (2006) · CIRP Annals · doi:10.1016/s0007-8506(07)60395-3 · Cited by 400
Qiu, C., Yue, S., Adkins, N. J. E., Ward, M., Hassanin, H., Lee, P. D., Withers, P. J., & Attallah, M. M. (2015) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.01.031 · Cited by 385
Self-citationSimchi, A., & Pohl, H. (2003) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(03)00341-1 · Cited by 377
Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., Ashcroft, I., Wildman, R. D., & Hague, R. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2882-8 · Cited by 342
Balling processes during selective laser treatment of powders
Tolochko, N. K., Mozzharov, S. E., Yadroitsev, I. A., Laoui, T., Froyen, L., Titov, V. I., & Ignatiev, M. B. (2004) · Rapid Prototyping Journal · doi:10.1108/13552540410526953 · Cited by 299
Selective laser melting of Invar 36: Microstructure and properties
Qiu, C., Adkins, N. J. E., & Attallah, M. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.10.020 · Cited by 292
X-ray photoelectron spectroscopy studies of reactions on chromium metal and chromium oxide surfaces
Payne, B. P., Biesinger, M. C., & McIntyre, N. S. (2010) · Journal of Electron Spectroscopy and Related Phenomena · doi:10.1016/j.elspec.2010.12.001 · Cited by 280
Dawes, J., Bowerman, R., & Trepleton, R. (2015) · Johnson Matthey Technology Review · doi:10.1595/205651315x688686 · Cited by 248
Mani, M., Lane, B., Donmez, A., Feng, S., Moylan, S., & Fesperman, R. (2015) · doi:10.6028/nist.ir.8036 · Cited by 242
Mani, M., Feng, S., Brandon, L., Donmez, A., Moylan, S., & Fesperman, R. (2017) · Additive Manufacturing Handbook · doi:10.1201/9781315119106-34 · Cited by 181
Synthesis of Nickel and Nickel Hydroxide Nanopowders by Simplified Chemical Reduction
Tientong, J., Garcia, S., Thurber, C. R., & Golden, T. D. (2014) · Journal of Nanotechnology · doi:10.1155/2014/193162 · Cited by 162
The effect of oxygen on transitional Marangoni flow in laser spot welding
Zhao, C., Kwakernaak, C., Pan, Y., Richardson, I. M., Saldi, Z. S., Kenjereš, S., & Kleijn, C. R. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.07.056 · Cited by 148
Leung, C. L. A., Marussi, S., Towrie, M., del Val, J., Atwood, R., Bodey, A. J., Jones, J. R., Withers, P. J., & Lee, P. D. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.08.025 · Cited by 137
Self-citationDynamic intensity normalization using eigen flat fields in X-ray imaging
Nieuwenhove, V. V., Beenhouwer, J. D., Carlo, F. D., Mancini, L., Marone, F., & Sijbers, J. (2015) · Optics Express · doi:10.1364/oe.23.027975 · Cited by 133
Additive Manufacturing: Policy Needed
Roca, J. B., Vaishnav, P., Fuchs, E. R. H., & Morgan, M. G. (2016) · Nature Materials · doi:10.1038/nmat4658 · Cited by 90
Metallurgical and Mechanical Evaluation of 4340 Steel Produced by Direct Metal Laser Sintering
Jelis, E., Clemente, M., Kerwien, S., Ravindra, N. M., & Hespos, M. R. (2015) · JOM · doi:10.1007/s11837-014-1273-8 · Cited by 83
Selective laser melting of Inconel 625 using pulse shaping
Mumtaz, K., & Hopkinson, N. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011049261 · Cited by 83
Effect of powder oxidation on the impact toughness of electron beam melting Ti-6Al-4V
Grell, W. A., Solis-Ramos, E., Clark, E. A., Lucon, E., Garboczi, E. J., Predecki, P., Loftus, Z., & Kumosa, M. (2017) · Additive manufacturing · doi:10.1016/j.addma.2017.08.002 · Cited by 54
Surface tension and wettability studies of liquid Fe-Ni-O alloys
Sharan, A., & Cramb, A. W. (1997) · Metallurgical and Materials Transactions B · doi:10.1007/s11663-997-0113-4 · Cited by 50
Cited by
Svetlizky, D., Das, M., Zheng, B., Vyatskikh, A. L., Bose, S., Bandyopadhyay, A., Schoenung, J. M., Lavernia, E. J., & Eliaz, N. (2021) · Materials Today · doi:10.1016/j.mattod.2021.03.020 · Cited by 1,371
Powder Bed Fusion of nickel-based superalloys: A review
Sanchez, S., Smith, P., Xu, Z., Gaspard, G., Hyde, C. J., Wits, W. W., Ashcroft, I. A., Chen, H., & Clare, A. T. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103729 · Cited by 541
Mostafaei, A., Ghiaasiaan, R., Ho, I.-T., Strayer, S., Chang, K.-C., Shamsaei, N., Shao, S., Paul, S., Yeh, A.-C., Tin, S., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101108 · Cited by 531
Metallurgy, mechanistic models and machine learning in metal printing
DebRoy, T., Mukherjee, T., Wei, H. L., Elmer, J. W., & Milewski, J. O. (2020) · Nature Reviews Materials · doi:10.1038/s41578-020-00236-1 · Cited by 497
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Metadata
- Authors
- Leung, C. L. A., Marussi, S., Towrie, M., Atwood, R. C., Withers, P. J., & Lee, P. D.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2019-03
- Volume
- 166
- Pages
- 294-305
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2904897658
- Cited by
- 336
- References
- 51
- FWCI
- 15.03
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.