The DOI matches its Crossref record; 13 of the 13 references it cites were found in a registry or an index.
Melt pool temperature and cooling rates in laser powder bed fusion
Open accessAbstract
In laser powder bed fusion, melt pool dynamics and stability are driven by the temperature field in the melt pool. If the temperature field is unfavourable defects are likely to form. The localised and rapid heating and cooling in the process presents a challenge for the experimental methods used to measure temperature. As a result, understanding of these process fundamentals is limited. In this paper a method is developed that uses coaxial imaging with high-speed cameras to give both the spatial and temporal resolution necessary to resolve the surface temperature of the melt pool. A two wavelength imaging setup is used to account for changes in emissivity. Temperature fields are captured at 100 kHz with a resolution of 20 μm during the processing of a simple Ti6Al4V component. Thermal gradients in the range 5–20 K/μm and cooling rates in range 1–40 K/μs are measured. The results presented give new insight into the effect of parameters, geometry and scan path on the melt pool temperature and cooling rates. The method developed here provides a new tool to assist in optimising scan strategies and parameters, identifying the causes of defect prone locations and controlling cooling rates for local microstructure development.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.02.014 · Cited by 2,766
Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
Everton, S. K., Hirsch, M., Stravroulakis, P., Leach, R. K., & Clare, A. T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.099 · Cited by 1,469
Denudation of metal powder layers in laser powder bed fusion processes
Matthews, M. J., Guss, G., Khairallah, S. A., Rubenchik, A. M., Depond, P. J., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.05.017 · Cited by 809
Zhao, C., Fezzaa, K., Cunningham, R. W., Wen, H., De Carlo, F., Chen, L., Rollett, A. D., & Sun, T. (2017) · Scientific Reports · doi:10.1038/s41598-017-03761-2 · Cited by 758
In-process sensing in selective laser melting (SLM) additive manufacturing
Spears, T. G., & Gold, S. A. (2016) · Integrating Materials and Manufacturing Innovation · doi:10.1186/s40192-016-0045-4 · Cited by 495
Clijsters, S., Craeghs, T., Buls, S., Kempen, K., & Kruth, J.-P. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6214-8 · Cited by 437
Criales, L. E., Arısoy, Y. M., Lane, B., Moylan, S., Donmez, A., & Özel, T. (2017) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2017.03.004 · Cited by 309
Quality control of laser- and powder bed-based Additive Manufacturing (AM) technologies
Berumen, S., Bechmann, F., Lindner, S., Kruth, J.-P., & Craeghs, T. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.089 · Cited by 307
Ki, H., Mazumder, J., & Mohanty, P. S. (2002) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-002-0190-6 · Cited by 293
Mani, M., Lane, B. M., Donmez, M. A., Feng, S. C., & Moylan, S. P. (2017) · International Journal of Production Research · doi:10.1080/00207543.2016.1223378 · Cited by 225
Pyrometric analysis of thermal processes in SLM technology
Pavlov, M. D., Doubenskaia, M., & Smurov, I. Y. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.080 · Cited by 140
FURUMOTO, T., Takashi, U. E. D. A., Alkahari, M. R., et al. (2013) · CIRP Annals · doi:10.1016/j.cirp.2013.03.032 · Cited by 129
Closed-loop automatic feedback control in electron beam melting
Mireles, J., Terrazas, C. A., Gaytan, S. M., Roberson, D. A., & Wicker, R. B. (2015) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6708-4 · Cited by 58
Cited by
Alloys-by-design: Application to new superalloys for additive manufacturing
Tang, Y. T., Panwisawas, C., Ghoussoub, J. N., Gong, Y., Clark, J. W. G., Németh, A. A. N., McCartney, D. G., & Reed, R. C. (2021) · Acta Materialia · doi:10.1016/j.actamat.2020.09.023 · Cited by 678
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Metal additive manufacturing: Technology, metallurgy and modelling
Cooke, S., Ahmadi, K., Willerth, S., & Herring, R. (2020) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2020.07.025 · Cited by 378
Guo, C., Li, G., Li, S., Hu, X., Lu, H., Li, X., Xu, Z., Chen, Y., Li, Q., Lu, J., et al. (2023) · Nano Materials Science · doi:10.1016/j.nanoms.2022.08.001 · Cited by 273
Metadata
- Authors
- Hooper, P. A.
- Venue
- Additive Manufacturing
- Publisher
- Elsevier BV
- Published
- 2018-08
- Volume
- 22
- Pages
- 548-559
- ISSN
- 2214-7810 (ISSN-L)
- 2214-8604
- OpenAlex
- W2803999279
- Cited by
- 707
- References
- 13
- FWCI
- 30.54
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.