Additive manufacturing of high solid content lunar regolith simulant paste based on vat photopolymerization and the effect of water addition on paste retention properties
Open accessIntegrity signals
Registry
Cites
Statistics
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
Xiao et al. measured density and open porosity at 2.73 g/cm3 and 3.12%, respectively.
“The density and open porosity were measured at 2.73 g/cm 3 and 3.12%, respectively.”
From A comprehensive review of lunar-based manufacturing and construction (2024) · cites this paper as [289]
The compression strengths reported by Wang, Liu, and Xiao are well beyond what other available papers have reported.
“The compression strength reported by Wang [288], Liu [285], and Xiao [289] are well beyond what other available papers have reported and should be independently replicated and verified.”
From A comprehensive review of lunar-based manufacturing and construction (2024) · cites this paper as [289]
Xiao et al. reported flexural strength of 132.21 MPa and compressive strength of 444.23 MPa in the optimal scenario.
“In the optimal scenario, a flexural strength of 132.21 MPa and a compressive strength of 444.23 MPa are reported.”
From A comprehensive review of lunar-based manufacturing and construction (2024) · cites this paper as [289]
Cites
Solar 3D printing of lunar regolith
Meurisse, A., Makaya, A., Willsch, C., & Sperl, M. (2018) · Acta Astronautica · doi:10.1016/j.actaastro.2018.06.063 · Cited by 287 · see citing works
Robust and elastic lunar and martian structures from 3D-printed regolith inks
Jakus, A. E., Koube, K. D., Geisendorfer, N. R., & Shah, R. N. (2017) · Scientific Reports · doi:10.1038/srep44931 · Cited by 141 · see citing works
Sintering of micro-trusses created by extrusion-3D-printing of lunar regolith inks
Taylor, S. L., Jakus, A. E., Koube, K. D., Ibeh, A. J., Geisendorfer, N. R., Shah, R. N., & Dunand, D. C. (2018) · Acta Astronautica · doi:10.1016/j.actaastro.2017.11.005 · Cited by 125 · see citing works
Additive manufacturing of lunar regolith structures
Altun, A. A., Ertl, F., Marechal, M., Makaya, A., Sgambati, A., & Schwentenwein, M. (2021) · Open Ceramics · doi:10.1016/j.oceram.2021.100058 · Cited by 88 · see citing works
Mechanical behaviour of additively manufactured lunar regolith simulant components
Goulas, A., Binner, J. G., Engstrøm, D. S., Harris, R. A., & Friel, R. J. (2019) · Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications · doi:10.1177/1464420718777932 · Cited by 84 · see citing works
Flagged first, then by citations
Cited by
Sorted by citations
A comprehensive review of lunar-based manufacturing and construction
Azami, M., Kazemi, Z., Moazen, S., Dubé, M., Potvin, M.-J., & Skonieczny, K. (2024) · Progress in Aerospace Sciences · doi:10.1016/j.paerosci.2024.101045 · Cited by 57 · see citing works
- Authors
- Xiao, C., Zheng, K., Chen, S., Li, N., Shang, X., Wang, F., Liang, J., Khan, S. B., Shen, Y., Lu, B., Ma, H., & Chen, Z.
- Affiliations
- Dongguan University of Technology (CN)
- Shenzhen University (CN)
- Corresponding author
- Chen, Shenggui
- Ma, Hongwei
- Chen, Zhangwei
- ORCID
- Venue
- Additive Manufacturing
- Publisher
- Elsevier BV
- Published
- 2023-06
- Volume
- 71
- Pages
- 103607
- ISSN
- 2214-7810 (ISSN-L)
- 2214-8604
- OpenAlex
- W4376130072
- Cited by
- 63
- References
- 5
- Citations by year
- 2026: 3 · 2025: 15 · 2024: 41 · 2023: 4
- FWCI
- 7.58
- Type
- journal article
- Language
- en
- Open access
- green
- doi.org
- Licence
- Locations
- Additive manufacturing (publishedVersion)
- SSRN Electronic Journal (acceptedVersion)
- Funders
- Guangdong Provincial Department of Science and Technology
- Basic and Applied Basic Research Foundation of Guangdong Province (2019B1515130005)
- Topics
- Physical Sciences › Engineering › Building and Construction › Innovations in Concrete and Construction Materials
- Physical Sciences › Engineering › Automotive Engineering › Additive Manufacturing and 3D Printing Technologies
- Physical Sciences › Engineering › Mechanical Engineering › Additive Manufacturing Materials and Processes
- Keywords
- lunar regolith simulant, vat photopolymerization, stereolithography, water addition, emulsification, surface tension reduction, viscosity reduction, layer thickness, interlayer bonding, flexural strength, compressive strength, in-situ resource utilization, lunar base construction
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
