The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Development of stiff, strong, yet tough composites by the addition of solvent exfoliated graphene to polyurethane
Open accessAbstract
Abstract We have prepared graphene dispersions, stabilised by polyurethane in tetrahydrofuran and dimethylformamide. These dispersions can be drop-cast to produce free-standing composite films. The graphene mass fraction is determined by the concentration of dispersed graphene and can be controllably varied from 0% to 90%. Raman spectroscopy and helium ion microscopy show the graphene to be well-dispersed and well-exfoliated in the composites, even at mass fractions of 55%. On addition of graphene, the Young’s modulus and stress at 3% strain increase by ×100, saturating at 1 GPa and 25 MPa, respectively, for mass fractions above 50 wt%. While the ultimate tensile strength does not vary significantly with graphene content, the strain at break and toughness degrade heavily on graphene addition. Both these properties fall by ×1000 as the graphene content is increased to 90 wt%. However, the rate of increase of Young’s modulus and stress at 3% strain with mass fraction is greater than the rate of decrease of ductility and toughness. This makes it possible to prepare composites with high modulus, stress at low strain and ultimate tensile strength as well as relatively high toughness and ductility. This could lead to new materials that are stiff, strong and tough.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Graphene-based composite materials
Stankovich, S., Dikin, D. A., Dommett, G. H. B., Kohlhaas, K. M., Zimney, E. J., Stach, E. A., Piner, R. D., Nguyen, S. T., & Ruoff, R. S. (2006) · Nature · doi:10.1038/nature04969 · Cited by 12,922
Koerner, H., Price, G., Pearce, N. A., Alexander, M., & Vaia, R. A. (2004) · Nature Materials · doi:10.1038/nmat1059 · Cited by 1,034
Cited by
Two-Dimensional Nanosheets Produced by Liquid Exfoliation of Layered Materials
Coleman, J. N., Lotya, M., O’Neill, A., Bergin, S. D., King, P. J., Khan, U., Young, K., Gaucher, A., De, S., Smith, R. J., et al. (2011) · Science · doi:10.1126/science.1194975 · Cited by 7,242
Self-citationGraphene-based polymer nanocomposites
Potts, J. R., Dreyer, D. R., Bielawski, C. W., & Ruoff, R. S. (2011) · Polymer · doi:10.1016/j.polymer.2010.11.042 · Cited by 3,123
Mechanical properties of graphene and graphene-based nanocomposites
Papageorgiou, D. G., Kinloch, I. A., & Young, R. J. (2017) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.07.004 · Cited by 2,579
The chemical and structural analysis of graphene oxide with different degrees of oxidation
Krishnamoorthy, K., Veerapandian, M., Yun, K., & Kim, S.-J. (2013) · Carbon · doi:10.1016/j.carbon.2012.10.013 · Cited by 2,017
The mechanics of graphene nanocomposites: A review
Young, R. J., Kinloch, I. A., Gong, L., & Novoselov, K. S. (2012) · Composites Science and Technology · doi:10.1016/j.compscitech.2012.05.005 · Cited by 1,294
Metadata
- Authors
- Khan, U., May, P., O’Neill, A., & Coleman, J. N.
- Venue
- Carbon
- Publisher
- Elsevier BV
- Published
- 2010-11
- Volume
- 48
- Issue
- 14
- Pages
- 4035-4041
- ISSN
- 0008-6223 (ISSN-L)
- OpenAlex
- W2006849467
- Cited by
- 309
- References
- 2
- FWCI
- 10.97
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Development of stiff, strong, yet tough composites by the addition of solvent exfoliated graphene to polyurethane. https://app.cochat.ai/papers/10.1016/j.carbon.2010.07.008
- The paper
- Khan, U., May, P., O’Neill, A., & Coleman, J. N. (2010). Development of stiff, strong, yet tough composites by the addition of solvent exfoliated graphene to polyurethane. Carbon. https://doi.org/10.1016/j.carbon.2010.07.008
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.