The DOI matches its Crossref record; 38 of the 38 references it cites were found in a registry or an index.
Development of stiff, strong, yet tough composites by the addition of solvent exfoliated graphene to polyurethane
Open accessAbstract
We have prepared graphene dispersions, stabilised by polyurethane in tetrahydrofuran and dimethylformamide. These dispersions can be drop-cast to produce free-standing composite films. The graphene mass fraction is determined by the concentration of dispersed graphene and can be controllably varied from 0% to 90%. Raman spectroscopy and helium ion microscopy show the graphene to be well-dispersed and well-exfoliated in the composites, even at mass fractions of 55%. On addition of graphene, the Young’s modulus and stress at 3% strain increase by ×100, saturating at 1 GPa and 25 MPa, respectively, for mass fractions above 50 wt%. While the ultimate tensile strength does not vary significantly with graphene content, the strain at break and toughness degrade heavily on graphene addition. Both these properties fall by ×1000 as the graphene content is increased to 90 wt%. However, the rate of increase of Young’s modulus and stress at 3% strain with mass fraction is greater than the rate of decrease of ductility and toughness. This makes it possible to prepare composites with high modulus, stress at low strain and ultimate tensile strength as well as relatively high toughness and ductility. This could lead to new materials that are stiff, strong and tough.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Measurement of the Elastic Properties and Intrinsic Strength of Monolayer Graphene
Lee, C., Wei, X., Kysar, J. W., & Hone, J. (2008) · Science · doi:10.1126/science.1157996 · Cited by 20,847
Raman Spectrum of Graphene and Graphene Layers
Ferrari, A. C., Meyer, J. C., Scardaci, V., Casiraghi, C., Lazzeri, M., Mauri, F., Piscanec, S., Jiang, D., Novoselov, K. S., Roth, S., et al. (2006) · Physical Review Letters · doi:10.1103/physrevlett.97.187401 · Cited by 15,047
Graphene-based composite materials
Stankovich, S., Dikin, D. A., Dommett, G. H. B., Kohlhaas, K. M., Zimney, E. J., Stach, E. A., Piner, R. D., Nguyen, S. T., & Ruoff, R. S. (2006) · Nature · doi:10.1038/nature04969 · Cited by 12,922
High-yield production of graphene by liquid-phase exfoliation of graphite
Hernandez, Y., Nicolosi, V., Lotya, M., Blighe, F. M., Sun, Z., De, S., McGovern, I. T., Holland, B., Byrne, M., Gun'Ko, Y. K., et al. (2008) · Nature Nanotechnology · doi:10.1038/nnano.2008.215 · Cited by 6,285
Self-citationSmall but strong: A review of the mechanical properties of carbon nanotube–polymer composites
Coleman, J. N., Khan, U., Blau, W. J., & Gun’ko, Y. K. (2006) · Carbon · doi:10.1016/j.carbon.2006.02.038 · Cited by 4,071
Self-citationFunctionalized graphene sheets for polymer nanocomposites
Ramanathan, T., Abdala, A. A., Stankovich, S., Dikin, D. A., Herrera-Alonso, M., Piner, R. D., Adamson, D. H., Schniepp, H. C., Chen, X., Ruoff, R. S., et al. (2008) · Nature Nanotechnology · doi:10.1038/nnano.2008.96 · Cited by 3,470
Synthesis and exfoliation of isocyanate-treated graphene oxide nanoplatelets
Stankovich, S., Piner, R. D., Nguyen, S. T., & Ruoff, R. S. (2006) · Carbon · doi:10.1016/j.carbon.2006.06.004 · Cited by 2,224
Liang, J., Huang, Y., Zhang, L., Wang, Y., Ma, Y., Guo, T., & Chen, Y. (2009) · Advanced Functional Materials · doi:10.1002/adfm.200801776 · Cited by 1,605
Enhanced Mechanical Properties of Graphene-Based Poly(vinyl alcohol) Composites
Zhao, X., Zhang, Q., Chen, D., & Lu, P. (2010) · Macromolecules · doi:10.1021/ma902862u · Cited by 1,426
Koerner, H., Price, G., Pearce, N. A., Alexander, M., & Vaia, R. A. (2004) · Nature Materials · doi:10.1038/nmat1059 · Cited by 1,034
High-Concentration, Surfactant-Stabilized Graphene Dispersions
Lotya, M., King, P. J., Khan, U., De, S., & Coleman, J. N. (2010) · ACS Nano · doi:10.1021/nn1005304 · Cited by 1,015
Self-citationHigh‐Concentration Solvent Exfoliation of Graphene
Khan, U., O'Neill, A., Lotya, M., De, S., & Coleman, J. N. (2010) · Small · doi:10.1002/smll.200902066 · Cited by 1,010
Self-citationStrong and ductile poly(vinyl alcohol)/graphene oxide composite films with a layered structure
Xu, Y., Hong, W., Bai, H., Li, C., & Shi, G. (2009) · Carbon · doi:10.1016/j.carbon.2009.08.022 · Cited by 732
Processing-property relationships of polycarbonate/graphene composites
Kim, H., & Macosko, C. W. (2009) · Polymer · doi:10.1016/j.polymer.2009.05.038 · Cited by 669
Measurement of Multicomponent Solubility Parameters for Graphene Facilitates Solvent Discovery
Hernandez, Y., Lotya, M., Rickard, D., Bergin, S. D., & Coleman, J. N. (2010) · Langmuir · doi:10.1021/la903188a · Cited by 659
Self-citationLiquid‐Phase Exfoliation of Nanotubes and Graphene
Coleman, J. N. (2009) · Advanced Functional Materials · doi:10.1002/adfm.200901640 · Cited by 654
Self-citationInterfacial Stress Transfer in a Graphene Monolayer Nanocomposite
Gong, L., Kinloch, I. A., Young, R. J., Riaz, I., Jalil, R., & Novoselov, K. S. (2010) · Advanced Materials · doi:10.1002/adma.200904264 · Cited by 643
High Performance Nanotube‐Reinforced Plastics: Understanding the Mechanism of Strength Increase
Coleman, J. N., Cadek, M., Blake, R., Nicolosi, V., Ryan, K. P., Belton, C., Fonseca, A., Nagy, J. B., Gun'ko, Y. K., & Blau, W. J. (2004) · Advanced Functional Materials · doi:10.1002/adfm.200305200 · Cited by 610
Self-citationMeasurement of carbon nanotube–polymer interfacial strength
Barber, A. H., Cohen, S. R., & Wagner, H. D. (2003) · Applied Physics Letters · doi:10.1063/1.1579568 · Cited by 540
Nano-indentation studies on polymer matrix composites reinforced by few-layer graphene
Das, B., Eswar Prasad, K., Ramamurty, U., & Rao, C. N. R. (2009) · Nanotechnology · doi:10.1088/0957-4484/20/12/125705 · Cited by 407
Korley, L. T. J., Pate, B. D., Thomas, E. L., & Hammond, P. T. (2006) · Polymer · doi:10.1016/j.polymer.2006.02.093 · Cited by 366
Koerner, H., Liu, W., Alexander, M., Mirau, P., Dowty, H., & Vaia, R. A. (2005) · Polymer · doi:10.1016/j.polymer.2005.02.025 · Cited by 351
Kim, I., & Jeong, Y. G. (2010) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.21956 · Cited by 331
Lee, Y. R., Raghu, A. V., Jeong, H. M., & Kim, B. K. (2009) · Macromolecular Chemistry and Physics · doi:10.1002/macp.200900157 · Cited by 297
Bourlinos, A. B., Georgakilas, V., Zboril, R., Steriotis, T. A., Stubos, A. K., & Trapalis, C. (2009) · Solid State Communications · doi:10.1016/j.ssc.2009.09.018 · Cited by 291
Nguyen, D. A., Lee, Y. R., Raghu, A. V., Jeong, H. M., Shin, C. M., & Kim, B. K. (2009) · Polymer International · doi:10.1002/pi.2549 · Cited by 252
Mechanical Reinforcement of Polyethylene Using Polyethylene‐Grafted Multiwalled Carbon Nanotubes
Yang, B. ‐., Pramoda, K. P., Xu, G. Q., & Goh, S. H. (2007) · Advanced Functional Materials · doi:10.1002/adfm.200600599 · Cited by 247
Raghu, A. V., Lee, Y. R., Jeong, H. M., & Shin, C. M. (2008) · Macromolecular Chemistry and Physics · doi:10.1002/macp.200800395 · Cited by 245
The mechanical properties and morphology of a graphite oxide nanoplatelet/polyurethane composite
Cai, D., Yusoh, K., & Song, M. (2009) · Nanotechnology · doi:10.1088/0957-4484/20/8/085712 · Cited by 226
Carbon nanotube-reinforced polyurethane composite fibers
Chen, W., Tao, X., & Liu, Y. (2006) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.01.024 · Cited by 177
Yoo, H. J., Jung, Y. C., Sahoo, N. G., & Cho, J. W. (2006) · Journal of Macromolecular Science Part B · doi:10.1080/00222340600767471 · Cited by 143
Transient Microstructure of Low Hard Segment Thermoplastic Polyurethane under Uniaxial Deformation
Koerner, H., Kelley, J. J., & Vaia, R. A. (2008) · Macromolecules · doi:10.1021/ma800306z · Cited by 113
Structural and mechanical characterization of nanoclay-reinforced agarose nanocomposites
Li, X., Gao, H., Scrivens, W. A., Fei, D., Thakur, V., Sutton, M. A., Reynolds, A. P., & Myrick, M. L. (2005) · Nanotechnology · doi:10.1088/0957-4484/16/10/006 · Cited by 100
Cai, D., & Song, M. (2009) · Nanotechnology · doi:10.1088/0957-4484/20/31/315708 · Cited by 98
Shape memory polyurethane containing mesogenic moiety
Jeong, H. M., Lee, J. B., Lee, S. Y., & Kim, B. K. (2000) · Journal of Materials Science · doi:10.1023/a:1004728814128 · Cited by 97
The effect of solvent choice on the mechanical properties of carbon nanotube–polymer composites
Khan, U., Ryan, K. M., Blau, W. J., & Coleman, J. N. (2007) · Composites Science and Technology · doi:10.1016/j.compscitech.2007.04.015 · Cited by 78
Self-citationReal-Time Study of Graphene’s Phase Transition in Polymer Matrices
Li, Q., Li, Z., Chen, M., & Fang, Y. Z. (2009) · Nano Letters · doi:10.1021/nl900681n · Cited by 54
Khan, U. N., Blighe, F. M., & Coleman, J. N. (2010) · The Journal of Physical Chemistry C · doi:10.1021/jp102938q · Cited by 49
Self-citation
Cited by
Two-Dimensional Nanosheets Produced by Liquid Exfoliation of Layered Materials
Coleman, J. N., Lotya, M., O’Neill, A., Bergin, S. D., King, P. J., Khan, U., Young, K., Gaucher, A., De, S., Smith, R. J., et al. (2011) · Science · doi:10.1126/science.1194975 · Cited by 7,242
Self-citationGraphene-based polymer nanocomposites
Potts, J. R., Dreyer, D. R., Bielawski, C. W., & Ruoff, R. S. (2011) · Polymer · doi:10.1016/j.polymer.2010.11.042 · Cited by 3,123
Mechanical properties of graphene and graphene-based nanocomposites
Papageorgiou, D. G., Kinloch, I. A., & Young, R. J. (2017) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.07.004 · Cited by 2,579
The chemical and structural analysis of graphene oxide with different degrees of oxidation
Krishnamoorthy, K., Veerapandian, M., Yun, K., & Kim, S.-J. (2013) · Carbon · doi:10.1016/j.carbon.2012.10.013 · Cited by 2,017
The mechanics of graphene nanocomposites: A review
Young, R. J., Kinloch, I. A., Gong, L., & Novoselov, K. S. (2012) · Composites Science and Technology · doi:10.1016/j.compscitech.2012.05.005 · Cited by 1,294
Metadata
- Authors
- Khan, U., May, P., O’Neill, A., & Coleman, J. N.
- Venue
- Carbon
- Publisher
- Elsevier BV
- Published
- 2010-11
- Volume
- 48
- Issue
- 14
- Pages
- 4035-4041
- ISSN
- 0008-6223 (ISSN-L)
- OpenAlex
- W2006849467
- Cited by
- 309
- References
- 38
- FWCI
- 10.97
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.