The DOI matches its Crossref record; 183 of the 191 references it cites were found in a registry or an index.
One-part alkali-activated materials: A review
Open accessAbstract
Alkali-activated materials (AAM) are recognized as potential alternatives to ordinary Portland cement (OPC) in order to limit CO 2 emissions as well as beneficiate several wastes into useful products. However, the alkali activation process involves concentrated aqueous alkali solutions, which are corrosive, viscous, and, as such, difficult to handle and not user friendly. Consequently, the development of so-called one-part or “just add water” AAM may have greater potential than the conventional two-part AAM, especially in cast-in-situ applications. One-part AAM involves a dry mix that consists of a solid aluminosilicate precursor, a solid alkali source, and possible admixtures to which water is added, similar to the preparation of OPC. The dry mix can be prepared at elevated temperatures to facilitate the reactivity of certain raw materials. This review discusses current studies of one-part AAMs in terms of raw materials, activators, additives, mechanical and physical properties, curing mechanisms, hydration products, and environmental impacts.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“The mechanical strength of one-part geopolymers was found to be comparable to that of two-part geopolymers prepared with liquid activators [46].”
From A Review on Geopolymer Technology for Lunar Base Construction (2022) · cites this paper as [46]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A safe operating space for humanity
Rockström, J., Steffen, W., Noone, K., Persson, Å., Chapin, F. S., Lambin, E. F., Lenton, T. M., Scheffer, M., Folke, C., Schellnhuber, H. J., et al. (2009) · Nature · doi:10.1038/461472a · Cited by 13,333
Geopolymer technology: The current state of the art
Duxson, P., Fernández-Jiménez, A., Provis, J. L., Lukey, G. C., Palomo, A., & van Deventer, J. S. J. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0637-z · Cited by 4,742
Davidovits, J. (1991) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/bf01912193 · Cited by 4,305
Ullmann's Encyclopedia of Industrial Chemistry
(2000) · Wiley eBooks · doi:10.1002/14356007 · Cited by 3,811
Carbon dioxide equivalent (CO2-e) emissions: A comparison between geopolymer and OPC cement concrete
Turner, L. K., & Collins, F. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.01.023 · Cited by 2,468
Provis, J. L. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.02.009 · Cited by 2,272
Costs and carbon emissions for geopolymer pastes in comparison to ordinary portland cement
McLellan, B. C., Williams, R. P., Lay, J., van Riessen, A., & Corder, G. D. (2011) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2011.02.010 · Cited by 1,949
Lea's Chemistry of Cement and Concrete
(2019) · Elsevier eBooks · doi:10.1016/c2013-0-19325-7 · Cited by 1,938
Duxson, P., Provis, J. L., Lukey, G. C., Mallicoat, S., Kriven, W. M., & van Deventer, J. S. J. (2005) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2005.06.060 · Cited by 1,812
New cements for the 21st century: The pursuit of an alternative to Portland cement
Shi, C., Jiménez, A. F., & Palomo, A. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.03.016 · Cited by 1,691
Sustainable cement production—present and future
Schneider, M., Römer, M., Tschudin, M., & Bolio, H. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.03.019 · Cited by 1,649
Global CO 2 emissions from cement production
Andrew, R. M. (2018) · Earth System Science Data · doi:10.5194/essd-10-195-2018 · Cited by 1,583
Geopolymer concrete: A review of some recent developments
Singh, B., Ishwarya, G., Gupta, M., & Bhattacharyya, S. K. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.03.036 · Cited by 1,487
Mechanism of geopolymerization and factors influencing its development: a review
Khale, D., & Chaudhary, R. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0401-4 · Cited by 1,475
Environmental management. Life cycle assessment. Principles and framework
(2006) · BSI Standards · doi:10.3403/30151316 · Cited by 1,427
Habert, G., de Lacaillerie, J.-B. D., & Roussel, N. (2011) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2011.03.012 · Cited by 1,420
García-Lodeiro, I., Palomo, A., Fernández‐Jiménez, A., & Macphee, D. E. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.05.006 · Cited by 1,381
On the Development of Fly Ash-Based Geopolymer Concrete
Hardjito, D., Wallah, S. E., Sumajouw, D. M. J., & Rangan, B. V. (2004) · ACI Materials Journal · doi:10.14359/13485 · Cited by 1,256
Resistance of geopolymer materials to acid attack
Bakharev, T. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.06.005 · Cited by 1,123
A review: The comparison between alkali-activated slag (Si + Ca) and metakaolin (Si + Al) cements
Li, C., Sun, H., & Li, L. (2010) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.03.020 · Cited by 1,109
Sustainable development and climate change initiatives
Damtoft, J. S., Lukasik, J., Herfort, D., Sorrentino, D., & Gartner, E. M. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.09.008 · Cited by 1,096
Fly ash-based geopolymer: clean production, properties and applications
Zhuang, X. Y., Chen, L., Komarneni, S., Zhou, C. H., Tong, D. S., Yang, H. M., Yu, W. H., & Wang, H. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.03.019 · Cited by 1,023
Lea's Chemistry of Cement and Concrete
(1998) · Elsevier eBooks · doi:10.1016/b978-0-7506-6256-7.x5007-3 · Cited by 1,019
Geopolymers and other alkali activated materials: why, how, and what?
Provis, J. L. (2013) · Materials and Structures · doi:10.1617/s11527-013-0211-5 · Cited by 1,014
Alkali-activated binders: A review
Pacheco-Torgal, F., Castro-Gomes, J. P., & Jalali, S. (2007) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.10.015 · Cited by 990
Effect of elevated temperatures on geopolymer paste, mortar and concrete
Kong, D. L. Y., & Sanjayan, J. G. (2010) · Cement and Concrete Research · doi:10.1016/j.cemconres.2009.10.017 · Cited by 985
Geopolymerisation: A review and prospects for the minerals industry
Komnitsas, K., & Zaharaki, D. (2007) · Minerals Engineering · doi:10.1016/j.mineng.2007.07.011 · Cited by 962
Provis, J. L., & van Deventer, J. S. J. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2 · Cited by 916
Duxson, P., Mallicoat, S., Lukey, G. C., Kriven, W. M., & van Deventer, J. S. J. (2006) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2006.05.044 · Cited by 905
Fly Ash-Based Geopolymer Concrete
Hardjito, D., Wallah, S. E., Sumajouw, D. M. J., & Rangan, B. V. (2005) · Australian Journal of Structural Engineering · doi:10.1080/13287982.2005.11464946 · Cited by 893
Assessment of CO2 reduction of alkali-activated concrete
Yang, K., Song, J., & Song, K.-I. (2012) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2012.08.001 · Cited by 841
Technical and commercial progress in the adoption of geopolymer cement
Van Deventer, J. S. J., Provis, J. L., & Duxson, P. (2012) · Minerals Engineering · doi:10.1016/j.mineng.2011.09.009 · Cited by 820
Designing Precursors for Geopolymer Cements
Duxson, P., & Provis, J. L. (2008) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2008.02787.x · Cited by 691
Handbook of Alkali-Activated Cements, Mortars and Concretes
Leonelli, C. (2015) · Elsevier eBooks · doi:10.1016/c2013-0-16511-7 · Cited by 688
Geopolymers : structure, processing, properties and industrial applications
Provis, J. L., & van Deventer, J. S. J. (2009) · Cited by 677
Rice husk ash as an alternate source for active silica production
Della, V. P., Kühn, I., & Hotza, D. (2002) · Materials Letters · doi:10.1016/s0167-577x(02)00879-0 · Cited by 657
Durability evaluation of geopolymer and conventional concretes
Albitar, M., Ali, M. S. M., Visintin, P., & Drechsler, M. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.01.056 · Cited by 632
Alkali-activated cements Opportunities and challenges
Roy, D. M. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(98)00093-3 · Cited by 611
Gartner, E., & Hirao, H. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.04.012 · Cited by 607
(Micro)-structural comparison between geopolymers, alkali-activated slag cement and Portland cement
Lecomte, I., Henrist, C., Liégeois, M., Maseri, F., Rulmont, A., & Cloots, R. (2006) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2005.12.021 · Cited by 605
Myers, R. J., Bernal, S. A., San Nicolas, R., & Provis, J. L. (2013) · Langmuir · doi:10.1021/la4000473 · Cited by 579
Walkley, B., Nicolas, R. S., Sani, M., Rees, G. J., Hanna, J. V., van Deventer, J. S. J., & Provis, J. L. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.08.010 · Cited by 561
The surface chemistry of Bayer process solids: a review
Hind, A. R., Bhargava, S. K., & Grocott, S. C. (1999) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/s0927-7757(98)00798-5 · Cited by 549
Fly ash-based geopolymers: The relationship between composition, pore structure and efflorescence
Zhang, Z., Provis, J. L., Reid, A., & Wang, H. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.06.004 · Cited by 545
Chindaprasirt, P., Silva, P. D., Sagoe‐Crentsil, K., & Hanjitsuwan, S. (2012) · Journal of Materials Science · doi:10.1007/s10853-012-6353-y · Cited by 543
Ken, P. W., Ramli, M. B., & Cheah, C. B. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.12.065 · Cited by 526
Kim, M. S., Jun, Y., Lee, C., & Oh, J. E. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.09.011 · Cited by 521
A review on alkaline activation: New analytical perspectives
Palomo, A., Krivenko, P., Garcia-Lodeiro, I., Kavalerova, E., Maltseva, O., & Fernández-Jiménez, A. (2014) · Materiales de Construcción · doi:10.3989/mc.2014.00314 · Cited by 501
Review Processing, properties and applications of reactive silica from rice husk—an overview
Chandrasekhar, S., Satyanarayana, K. G., Pramada, P. N., Raghavan, P., & Gupta, T. N. (2003) · Journal of Materials Science · doi:10.1023/a:1025157114800 · Cited by 491
Wan, Q., Rao, F., Song, S., García, R. E., Morales‐Estrella, R., León-Patiño, C. A., & Zhang, Y. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.01.014 · Cited by 483
29Si NMR Study of Structural Ordering in Aluminosilicate Geopolymer Gels
Duxson, P., Provis, J. L., Lukey, G. C., Separovic, F., & van Deventer, J. S. J. (2005) · Langmuir · doi:10.1021/la047336x · Cited by 481
Temuujin, J., Williams, R. P., & van Riessen, A. (2009) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2009.03.016 · Cited by 465
Red mud addition in the raw meal for the production of Portland cement clinker
Tsakiridis, P. E., Agatzini-Leonardou, S., & Oustadakis, P. (2004) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2004.08.002 · Cited by 445
Effect of fire exposure on cracking, spalling and residual strength of fly ash geopolymer concrete
Sarker, P. K., Kelly, S., & Yao, Z. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.06.059 · Cited by 441
Nematollahi, B., Sanjayan, J., & Shaikh, F. U. A. (2015) · Ceramics International · doi:10.1016/j.ceramint.2014.12.154 · Cited by 430
Concrete: An eco material that needs to be improved
Flatt, R. J., Roussel, N., & Cheeseman, C. R. (2012) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2011.11.012 · Cited by 397
Variation in hybrid cements over time. Alkaline activation of fly ash–portland cement blends
García-Lodeiro, I., Fernández‐Jiménez, A., & Palomo, A. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.03.022 · Cited by 396
An overview of geopolymers derived from industrial by-products
Mehta, A., & Siddique, R. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.09.136 · Cited by 393
Utilization of silica fume in concrete: Review of durability properties
Khan, M. I., & Siddique, R. (2011) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2011.09.016 · Cited by 374
TRENDS IN RED MUD UTILIZATION – A REVIEW
Paramguru, R. K., RATH, P. C., & Misra, V. N. (2004) · Mineral Processing and Extractive Metallurgy Review · doi:10.1080/08827500490477603 · Cited by 372
Palacios, M., & Puertas, F. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.10.014 · Cited by 368
Synthesis and strength optimization of one-part geopolymer based on red mud
Ye, N., Yang, J., Liang, S., Hu, Y. Q., Hu, J., Xiao, B., & Huang, Q. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.02.099 · Cited by 364
Minimising the global warming potential of clay based geopolymers
Heath, A. C., Paine, K. A., & McManus, M. C. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.04.046 · Cited by 356
Life cycle inventories for the production of sodium silicates
Fawer, M. S., Concannon, M., & Rieber, W. (1999) · The International Journal of Life Cycle Assessment · doi:10.1007/bf02979498 · Cited by 338
A study on the setting characteristics of sodium silicate-activated slag pastes
Chang, J.-R. (2003) · Cement and Concrete Research · doi:10.1016/s0008-8846(02)01096-7 · Cited by 332
Recent update on the environmental impact of geopolymers
Habert, G., & Ouellet-Plamondon, C. (2016) · RILEM Technical Letters · doi:10.21809/rilemtechlett.2016.6 · Cited by 330
Effect of Alumina Release Rate on the Mechanism of Geopolymer Gel Formation
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2010) · Chemistry of Materials · doi:10.1021/cm101151n · Cited by 322
Properties of cementless mortars activated by sodium silicate
Yang, K., Song, J., Ashour, A. F., & Lee, E. (2007) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.07.003 · Cited by 319
A thermodynamic model for C-(N-)A-S-H gel: CNASH_ss. Derivation and validation
Myers, R. J., Bernal, S. A., & Provis, J. L. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.07.005 · Cited by 318
Review of mechanical properties of short fibre reinforced geopolymer composites
Shaikh, F. U. A. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.01.026 · Cited by 314
Opc-fly ash cementitious systems: study of gel binders produced during alkaline hydration
Palomo, A., Fernández‐Jiménez, A., Kovalchuk, G., Ordoñez, L. M., & Naranjo, M. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0585-7 · Cited by 290
One‐Part Geopolymers Based on Thermally Treated Red Mud/NaOH Blends
Ke, X., Bernal, S. A., Ye, N., Provis, J. L., & Yang, J. (2014) · Journal of the American Ceramic Society · doi:10.1111/jace.13231 · Cited by 284
Global CO2 emissions from cement production
Andrew, R. M. (2017) · Figshare · doi:10.5281/zenodo.831454 · Cited by 282
The effect of silica availability on the mechanism of geopolymerisation
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.02.001 · Cited by 281
The role of particle technology in developing sustainable construction materials
Provis, J. L., Duxson, P., & van Deventer, J. S. J. (2010) · Advanced Powder Technology · doi:10.1016/j.apt.2009.10.006 · Cited by 280
Alkali–aggregate reaction in activated fly ash systems
García-Lodeiro, I., Palomo, A., & Fernández‐Jiménez, A. (2006) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.11.002 · Cited by 262
Life cycle assessment (LCA) of alkali-activated cements and concretes
Ouellet‐Plamondon, C., & Habert, G. (2015) · Elsevier eBooks · doi:10.1533/9781782422884.5.663 · Cited by 257
Combustion behaviour of rice husk in a bubbling fluidised bed
Armesto, L., Bahillo, A., Veijonen, K., Cabanillas, A., & Otero, J. (2002) · Biomass and Bioenergy · doi:10.1016/s0961-9534(02)00046-6 · Cited by 250
Effect of chemical admixtures on properties of high-calcium fly ash geopolymer
Rattanasak, U., Pankhet, K., & Chindaprasirt, P. (2011) · International Journal of Minerals Metallurgy and Materials · doi:10.1007/s12613-011-0448-3 · Cited by 247
The mechanism of geopolymer gel formation investigated through seeded nucleation
Rees, C. A., Provis, J. L., Lukey, G. C., & van Deventer, J. S. J. (2007) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2007.12.019 · Cited by 244
Thermal Activation of Albite for the Synthesis of One‐Part Mix Geopolymers
Feng, D., Provis, J. L., & van Deventer, J. S. J. (2011) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2011.04925.x · Cited by 243
One-Part Geopolymer Mixes from Geothermal Silica and Sodium Aluminate
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie8006825 · Cited by 239
Bauxite residue in cement and cementitious applications: Current status and a possible way forward
Pontikes, Y., & Angelopoulos, G. N. (2013) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2013.01.005 · Cited by 224
Hydration kinetics in hybrid binders: Early reaction stages
Garcia-Lodeiro, I., Fernandez-Jimenez, A., & Palomo, A. (2013) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.03.025 · Cited by 224
Nematollahi, B., Sanjayan, J., Qiu, J., & Yang, E. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.11.117 · Cited by 224
Life-cycle analysis of geopolymers
Weil, M., Dombrowski, Κ., & Buchwald, A. (2009) · Elsevier eBooks · doi:10.1533/9781845696382.2.194 · Cited by 223
Dehydroxylation of kaolinite to metakaolin—a molecular dynamics study
Sperinck, S., Raiteri, P., Marks, N. A., & Wright, K. (2010) · Journal of Materials Chemistry · doi:10.1039/c0jm01748e · Cited by 222
Geopolymer technology, from fundamentals to advanced applications: a review
Majidi, B. (2009) · Materials Technology · doi:10.1179/175355509x449355 · Cited by 219
Zhang, M., Zhao, M., Zhang, G., Mann, D., Lumsden, K., & Tao, M. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.07.108 · Cited by 219
Adsorption of superplasticizer admixtures on alkali-activated slag pastes
Palacios, M., Houst, Y. F., Bowen, P., & Puertas, F. (2009) · Cement and Concrete Research · doi:10.1016/j.cemconres.2009.05.005 · Cited by 215
Properties and sustainability of alkali-activated slag foamed concrete
Yang, K., Lee, K., Song, J., & Gong, M.-H. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2013.12.068 · Cited by 214
The suitability of thermally activated illite/smectite clay as raw material for geopolymer binders
Buchwald, A., Hohmann, M., Posern, K., & Brendler, E. (2009) · Applied Clay Science · doi:10.1016/j.clay.2009.08.026 · Cited by 214
Sodium silicate-based alkali-activated slag mortars
Brough, A. R., Holloway, M., Sykes, J. M., & Atkinson, A. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00356-2 · Cited by 211
Tensile Strain Hardening Behavior of PVA Fiber-Reinforced Engineered Geopolymer Composite
Nematollahi, B., Sanjayan, J., & Shaikh, F. U. A. (2015) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001242 · Cited by 207
Rahier, H., Simons, W., Mele, B. V., & Biesemans, M. (1997) · Journal of Materials Science · doi:10.1023/a:1018563914630 · Cited by 201
Synthesizing one-part geopolymers from rice husk ash
Sturm, P., Gluth, G. J. G., Brouwers, H. J. H., & Kühne, H. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.017 · Cited by 201
Co-disposal of MSWI fly ash and Bayer red mud using an one-part geopolymeric system
Ye, N., Chen, Y., Yang, J., Liang, S., Hu, Y. Q., Xiao, B., Huang, Q., Shi, Y., Hu, J., & Wu, X. (2016) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2016.06.042 · Cited by 198
Characterisation of One-Part Geopolymer Binders Made from Fly Ash
Hajimohammadi, A., & van Deventer, J. S. J. (2016) · Waste and Biomass Valorization · doi:10.1007/s12649-016-9582-5 · Cited by 192
Rheology and Setting of Alkali-Activated Slag Pastes and Mortars: Effect of Organic Admixture
Palacios, M., Banfill, P. F. G., & Puertas, F. (2008) · ACI Materials Journal · doi:10.14359/19754 · Cited by 191
Nematollahi, B., Sanjayan, J., Qiu, J., & Yang, E. (2017) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2016.12.005 · Cited by 189
Compressive strength of one-part alkali activated fly ash using red mud as alkali supplier
Choo, H., Lim, S. H., Lee, W. W., & Lee, C.-H. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.015 · Cited by 185
Activating solution chemistry for geopolymers
Provis, J. L. (2009) · Geopolymers · doi:10.1533/9781845696382.1.50 · Cited by 184
Pore characteristics in one-part mix geopolymers foamed by H 2 O 2 : The impact of mix design
Hajimohammadi, A., Ngo, T., Mendis, P. A., Nguyen, T. N., Kashani, A., & van Deventer, J. S. J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.05.084 · Cited by 183
GEOPOLYMER: Chemistry & Applications
Davidovits, J. (2011) · Cited by 183
A novel method to produce dry geopolymer cement powder
Abdel‐Gawwad, H. A., & Abo-El-Enein, S. A. (2014) · HBRC Journal · doi:10.1016/j.hbrcj.2014.06.008 · Cited by 176
Preparation, structure and hydrothermal stability of alternative (sodium silicate-free) geopolymers
Koloušek, D., Brus, J., Urbanová, M., Andertová, J., Hulı́nský, V., & Vorel, J. (2007) · Journal of Materials Science · doi:10.1007/s10853-007-1910-5 · Cited by 176
Mellado, A., Catalán, C., Bouzón, N., Borrachero, M. V., Monzó, J., & Payá, J. (2014) · RSC Advances · doi:10.1039/c4ra03375b · Cited by 173
Comparative deflection hardening behavior of short fiber reinforced geopolymer composites
Nematollahi, B., Sanjayan, J., & Shaikh, F. U. A. (2014) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.07.085 · Cited by 172
García-Lodeiro, I., Donatello, S., Fernández‐Jiménez, A., & Palomo, A. (2016) · Materials · doi:10.3390/ma9070605 · Cited by 169
Recent advances in the applied chemistry of the rare metals. Jubilee memorial lecture
ATKINSON, R. H. (1940) · Journal of the Society of Chemical Industry · doi:10.1002/jctb.5000591202 · Cited by 161
Yang, K., & Song, J. (2009) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)0899-1561(2009)21:3(119 · Cited by 159
Manufacture of hybrid cements with fly ash and bottom ash from a municipal solid waste incinerator
García-Lodeiro, I., Taboada, V. C., Fernández‐Jiménez, A., & Palomo, A. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.12.079 · Cited by 157
Djobo, J. N. Y., Elimbi, A., Tchakouté, H. K., & Kumar, S. (2016) · RSC Advances · doi:10.1039/c6ra03667h · Cited by 156
Alkali-activated fly ash-based geopolymers with zeolite or bentonite as additives
Hu, M., Zhu, X., & Long, F. (2009) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2009.07.006 · Cited by 153
Nie, Q., Hu, W., Ai, T., Huang, B., Shu, X., & He, Q. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.144 · Cited by 151
Fire endurance of steel reinforced fly ash geopolymer concrete elements
Sarker, P. K., & McBeath, S. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.04.054 · Cited by 147
Utilization of ferroalumina as raw material in the production of Ordinary Portland Cement
Vangelatos, I., Angelopoulos, G. N., & Boufounos, D. (2009) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2009.02.049 · Cited by 142
Geopolymerization and Its Potential Application in Mine Tailings Consolidation: A Review
Rao, F., & Liu, Q. (2015) · Mineral Processing and Extractive Metallurgy Review · doi:10.1080/08827508.2015.1055625 · Cited by 137
Drying shrinkage and creep performance of geopolymer concrete
Sagoe‐Crentsil, K., Brown, T., & Taylor, A. (2013) · Journal of Sustainable Cement-Based Materials · doi:10.1080/21650373.2013.764963 · Cited by 137
Resistance of geopolymer and Portland cement based systems to silage effluent attack
Aiken, T. A., Sha, W., Kwasny, J., & Soutsos, M. N. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.11.015 · Cited by 136
Garg, N., & White, C. E. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta00412e · Cited by 136
Mechanochemical synthesis of one-part alkali aluminosilicate hydraulic cement
Matalkah, F., Xu, L., Wu, W., & Soroushian, P. (2016) · Materials and Structures · doi:10.1617/s11527-016-0968-4 · Cited by 135
Chemically-bonded cementitious materials based on metakaolin
Palomo, A., & Glasser, F. P. (1992) · British ceramic. Transactions and journal · Cited by 132
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2011) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2011.02.045 · Cited by 126
Shi, C., Shi, Z., Hu, X., Zhao, R. X., & Chong, L. (2015) · Materials and Structures · doi:10.1617/s11527-014-0505-2 · Cited by 126
Effect of phosphate on the hydration of alkali-activated red mud–slag cementitious material
Gong, C., & Yang, N. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00260-x · Cited by 120
Comparison of embodied energies of Ordinary Portland Cement with Bayer-derived geopolymer products
Jamieson, E., McLellan, B. C., van Riessen, A., & Nikraz, H. (2015) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.03.008 · Cited by 118
Binder Chemistry – High-Calcium Alkali-Activated Materials
Bernal, S. A., Provis, J. L., Fernández‐Jiménez, A., Krivenko, P. V., Kаvalerova, Е., Palacios, M., & Shi, C. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2_3 · Cited by 118
Provis, J. L., & van Deventer, J. S. J. (2009) · Elsevier eBooks · doi:10.1533/9781845696382.1 · Cited by 110
Peng, M. X., Wang, Z. H., Shen, S. H., & Xiao, Q. G. (2014) · Materials and Structures · doi:10.1617/s11527-014-0350-3 · Cited by 109
Clay reactivity: Production of alkali activated cements
Ruiz-Santaquiteria, C., Fernández‐Jiménez, A., Skibsted, J., & Palomo, A. (2013) · Applied Clay Science · doi:10.1016/j.clay.2012.10.012 · Cited by 104
Railway sleepers made of alkali activated fly ash concrete
Palomo, A., Fernández‐Jiménez, A., Hombrados, C. L., & Lleyda, J. L. (2007) · Revista de ingeniería de construcción · doi:10.4067/s0718-50732007000200001 · Cited by 103
Potassium-rich biomass ashes as activators in metakaolin-based inorganic polymers
Peys, A., Rahier, H., & Pontikes, Y. (2015) · Applied Clay Science · doi:10.1016/j.clay.2015.11.003 · Cited by 103
Suwan, T., & Fan, M. (2016) · Materials and Manufacturing Processes · doi:10.1080/10426914.2016.1198013 · Cited by 103
Peng, M. X., Wang, Z. H., Shen, S. H., Xiao, Q. G., Li, L. J., Tang, Y. C., & Hu, L. L. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.11.010 · Cited by 96
Binder Chemistry – Low-Calcium Alkali-Activated Materials
Provis, J. L., Fernández‐Jiménez, A., Kamseu, E., Leonelli, C., & Palomo, A. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2_4 · Cited by 94
Seiffarth, T., Hohmann, M., Posern, K., & Kaps, C. (2012) · Applied Clay Science · doi:10.1016/j.clay.2012.09.010 · Cited by 90
EFC geopolymer concrete aircraft pavements at Brisbane West Wellcamp Airport
Glasby, T., Day, J., Genrich, R., & Aldred, J. (2015) · Cited by 88
Comparison of Geopolymer Fly Ash and Ordinary Portland Cement to the Strength of Concrete
Abdullah, M. M. A. B., Kamarudin, H., Binhussain, M., Nizar, I. K., Razak, R. A., & Zarina, Y. (2013) · Advanced Science Letters · doi:10.1166/asl.2013.5187 · Cited by 88
Development of Sucrose and Citric Acid as the Natural based Admixture for Fly Ash based Geopolymer
Kusbiantoro, A., Ibrahim, M. S., Muthusamy, K., & Alias, A. (2013) · Procedia Environmental Sciences · doi:10.1016/j.proenv.2013.02.075 · Cited by 85
Sturm, P., Gluth, G. J. G., Simon, S., Brouwers, H. J. H., & Kühne, H. (2016) · Thermochimica Acta · doi:10.1016/j.tca.2016.04.015 · Cited by 85
Preparation of drying powder inorganic polymer cement based on alkali-activated slag technology
Wang, K.-T., Du, L.-Q., Lv, X., He, Y., & Cui, X. (2017) · Powder Technology · doi:10.1016/j.powtec.2017.02.036 · Cited by 85
Influence of Curing on the Strength Development of Calcium-Containing Geopolymer Mortar
Li, X., Wang, Z., & Jiao, Z. (2013) · Materials · doi:10.3390/ma6115069 · Cited by 84
A review on thermophysical evaluation of alkali-activated geopolymers
Salahuddin, M. B. M., Mazlan, N., & Mustapha, F. B. (2014) · Ceramics International · doi:10.1016/j.ceramint.2014.11.119 · Cited by 83
Properties of alkali-activated mortar and concrete using lightweight aggregates
Yang, K., Song, J., & Lee, J.-S. (2009) · Materials and Structures · doi:10.1617/s11527-009-9499-6 · Cited by 82
Current developments and future needs in standards for cementitious materials
Hooton, R. D. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.05.022 · Cited by 78
Solid Reactant-Based Geopolymers from Rice Hull Ash and Sodium Aluminate
Hajimohammadi, A., & van Deventer, J. S. J. (2016) · Waste and Biomass Valorization · doi:10.1007/s12649-016-9735-6 · Cited by 77
Sturm, P., Greiser, S., Gluth, G. J. G., Jäger, C., & Brouwers, H. J. H. (2015) · Journal of Materials Science · doi:10.1007/s10853-015-9232-5 · Cited by 70
Abdollahnejad, Z., Miraldo, S., Pacheco-Torgal, F., & de Aguiar, J. L. B. (2015) · European Journal of Environmental and Civil engineering · doi:10.1080/19648189.2015.1125392 · Cited by 67
Peng, M. X., Wang, Z. H., Xiao, Q. G., Song, F., Xie, W., Yu, L. C., Huang, H. W., & Yi, S. J. (2017) · Applied Clay Science · doi:10.1016/j.clay.2017.01.020 · Cited by 67
Are geopolymers more suitable than Portland cement to produce high volume recycled aggregates HPC?
Pacheco-Torgal, F., Ding, Y., Miraldo, S., Abdollahnejad, Z., & Labrincha, J. A. (2012) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2012.07.004 · Cited by 66
Effect of Na3PO4 on the Hydration Process of Alkali-Activated Blast Furnace Slag
Kalina, L., Bílek, V., Novotný, R., Mončeková, M., Másilko, J., & Koplík, J. (2016) · Materials · doi:10.3390/ma9050395 · Cited by 65
Peys, A., Arnout, L., Blanpain, B., Rahier, H., Acker, K. V., & Pontikes, Y. (2017) · Waste and Biomass Valorization · doi:10.1007/s12649-017-9877-1 · Cited by 60
Flow and Compressive Strength of Alkali-Activated Mortars
Yang, K., Song, J., Lee, K., & Ashour, A. F. (2009) · ACI Materials Journal · doi:10.14359/56316 · Cited by 57
The behavior of silica in geothermal brine from Dieng geothermal power plant, Indonesia
Pambudi, N. A., Itoi, R., Yamashiro, R., Alam, B. Y. C. S., Tusara, L., Jalilinasrabady, S., & Jaelani, K. M. (2015) · Geothermics · doi:10.1016/j.geothermics.2014.12.003 · Cited by 53
Memon, F. A., Nuruddin, F., Demie, S., & Shafiq, N. (2012) · Cited by 53
Provis, J. L. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2_1 · Cited by 51
Benefits of Sealed-Curing on Compressive Strength of Fly Ash-Based Geopolymers
Lee, S., Van Riessen, A., & Chon, C.-M. (2016) · Materials · doi:10.3390/ma9070598 · Cited by 49
Duxson, P. (2009) · Elsevier eBooks · doi:10.1533/9781845696382.1.37 · Cited by 48
Compressive strength, microstructure and hydration products of hybrid alkaline cements
Abdollahnejad, Z., Hlavacek, P., Miraldo, S., Pacheco-Torgal, F., & de Aguiar, J. L. B. (2014) · Materials Research · doi:10.1590/s1516-14392014005000091 · Cited by 48
Dry powder alkali-activated slag cements
Kovtun, M., Kearsley, E. P., & Shekhovtsova, J. (2015) · Advances in Cement Research · doi:10.1680/jadcr.14.00078 · Cited by 47
Synthesis, characterisation and thermal behaviour of lithium aluminosilicate inorganic polymers
O’Connor, S. J., & MacKenzie, K. J. D. (2010) · Journal of Materials Science · doi:10.1007/s10853-010-4383-x · Cited by 45
Mechanisms and kinetics of gel formation in geopolymers
Rees, C. A. (2007) · Minerva Access (University of Melbourne) · Cited by 43
Obonyo, E., Kamseu, E., Melo, U. C., & Leonelli, C. (2011) · Sustainability · doi:10.3390/su3020410 · Cited by 41
Superplasticizer Addition to Carbon Fly Ash Geopolymers Activated at Room Temperature
Carabba, L., Manzi, S., & Bignozzi, M. C. (2016) · Materials · doi:10.3390/ma9070586 · Cited by 41
Petrillo, A., Cioffi, R., Felice, F. D., Colangelo, F., & Borrelli, C. (2016) · Environmental Progress & Sustainable Energy · doi:10.1002/ep.12421 · Cited by 40
Harish, K. V., & Rangaraju, P. R. (2013) · Advances in Civil Engineering Materials · doi:10.1520/acem20120056 · Cited by 39
Historical Aspects and Overview
Provis, J. L., Duxson, P., Kаvalerova, Е., Krivenko, P. V., Pan, Z., Puertas, F., & van Deventer, J. S. J. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2_2 · Cited by 38
Milestones in the analysis of alkali-activated binders
Provis, J. L., & Bernal, S. A. (2014) · Journal of Sustainable Cement-Based Materials · doi:10.1080/21650373.2014.958599 · Cited by 38
Geopolymerization of a silica residue from waste treatment of chlorosilane production
Gluth, G. J. G., Lehmann, C. W., Rübner, K., & Kühne, H. (2012) · Materials and Structures · doi:10.1617/s11527-012-9972-5 · Cited by 37
Khorasanipour, M. (2015) · Journal of Geochemical Exploration · doi:10.1016/j.gexplo.2015.03.001 · Cited by 37
Cements with a low clinker content: versatile use of raw materials
García-Lodeiro, I., Fernández‐Jiménez, A., & Palomo, A. (2015) · Journal of Sustainable Cement-Based Materials · doi:10.1080/21650373.2015.1040865 · Cited by 36
Efficacy of Available Superplasticizers on Geopolymers
Nematollahi, B., & Sanjayan, J. (2014) · Research Journal of Applied Sciences Engineering and Technology · doi:10.19026/rjaset.7.420 · Cited by 34
Characterisation of the Sarcheshmeh copper mine tailings, Kerman province, southeast of Iran
Malakooti, S. J., Tonkaboni, S. Z. S., Noaparast, M., Ardejani, F. D., & Naseh, R. (2013) · Environmental Earth Sciences · doi:10.1007/s12665-013-2630-6 · Cited by 27
Global CO 2 emissions from cement production
Andrew, R. M. (2017) · doi:10.5194/essd-2017-77 · Cited by 21
Specific Examples of Hybrid Alkaline Cement
Fernández‐Jiménez, A., García-Lodeiro, I., Donatello, S., Maltseva, O., & Palomo, A. (2014) · MATEC Web of Conferences · doi:10.1051/matecconf/20141101001 · Cited by 20
Optimising Ambient Setting Bayer Derived Fly Ash Geopolymers
Jamieson, E., Kealley, C. S., van Riessen, A., & Hart, R. (2016) · Materials · doi:10.3390/ma9050392 · Cited by 19
Chan, C. C. S., Thorpe, D., & Islam, M. M. (2015) · doi:10.1109/ieem.2015.7385607 · Cited by 12
Effect of Superplasticizers on Workability of Fly Ash Based Geopolymer
Nematollahi, B., & Sanjayan, J. (2014) · Springer eBooks · doi:10.1007/978-981-4585-02-6_61 · Cited by 10
Nematollahi, B., & Sanjayan, J. (2016) · Swinburne figshare (Swinburne University of Technology) · Cited by 8
Development of foam one-part geopolymers
Abdollahnejad, Z. (2016) · Portuguese National Funding Agency for Science, Research and Technology (RCAAP Project by FCT) · Cited by 4
Research works printed but not linked: 7
- H. Kühl, Slag cement and process making the same, US Patent 900,939 (1908).
- Purdon, 1940, The action of alkalis on blast-furnace slag, J. Soc. Chem. Ind., 59, 191
- R.F. Heitzmann, M. Fitzgerald, J.L. Sawyer, Mineral binder and compositions employing the same, Mineral binder and compositions employing the same. US Patent 4,642,137 (1987).
- W. Schwarz, A. Lerat, Tectoaluminosilicate cement and a process for its manufacture, Tectoaluminosilicate cement and a process for its manufacture. U.S. Patent 5,372,640 (1994).
- J. Davidovits, Method for obtaining a geopolymeric binder allowing to stabilize, solidify and consolidate toxic or waste materials, Method for obtaining a geopolymeric binder allowing to stabilize, solidify and consolidate toxic or waste materials. U.S. Patent 5,349,118 (1994).
- García-Lodeiro, 2012, Hybrid alkaline cements. Part I: Fundamentals, Rev. Rom. Mater. Rom. J. Mater., 42, 330
- Gluth, 2013, Geopolymerization of a silica residue from waste treatment of chlorosilane production, Mater. Struct., 46, 1291, 10.1617/s11527-012-9972-5 · DOI
Cited by
Sorted by citations
Recent progress in low-carbon binders
Shi, C., Qu, B., & Provis, J. L. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.05.009 · Cited by 732
Drying shrinkage in alkali-activated binders – A critical review
Mastali, M., Kinnunen, P., Dalvand, A., Mohammadi-Firouz, R., & Illikainen, M. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.09.125 · Cited by 470
Advances in alkali-activation of clay minerals
Khalifa, A., Çizer, Ö., Pontikes, Y., Heath, A. C., Patureau, P., Bernal, S. A., & Marsh, A. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106050 · Cited by 457
Wang, A., Zheng, Y., Zhang, Z., Liu, K., Li, Y., Shi, L., & Sun, D. (2020) · Engineering · doi:10.1016/j.eng.2019.08.019 · Cited by 397
Oderji, S. Y., Chen, B., Ahmad, M. R., & Shah, S. F. A. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.03.290 · Cited by 362
Metadata
- Authors
- Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M.
- Affiliations
- University of Oulu (FI)
- Venue
- Cement and Concrete Research
- Publisher
- Elsevier BV
- Published
- 2018-01
- Volume
- 103
- Pages
- 21-34
- ISSN
- 0008-8846 (ISSN-L)
- OpenAlex
- W2768077267
- Cited by
- 1,456
- References
- 191
- Citations by year
- 2026: 223 · 2025: 201 · 2024: 212 · 2023: 203 · 2022: 216 · 2021: 159 · 2020: 121 · 2019: 87 · 2018: 32
- FWCI
- 17.47
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- Locations
- Cement and Concrete Research (publishedVersion, cc-by-nc-nd)
- Funders
- Tekes (1105/31/2016)
- Topics
- Physical Sciences › Engineering › Civil and Structural Engineering › Concrete and Cement Materials Research
- Physical Sciences › Materials Science › Materials Chemistry › Magnesium Oxide Properties and Applications
- Physical Sciences › Environmental Science › Environmental Engineering › Microbial Applications in Construction Materials
- Keywords
- alkali-activated materials, aluminosilicate precursors, alkaline activator, dry mix, CO2 emission reduction, waste valorization, curing mechanism, hydration products, mechanical properties, environmental impact
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
